Search results for: method configuration
-
Pollutants removal effectiveness in hydrophyte filters with sequential vertical and horizontal flow
PublicationThe object of investigations was the constructed wetland in Wiedersberg in Saxonia in Germany supplied with domestic sewage from 145 inhabitants. The biological part was composed of sequential reed beds with vertical and horizontal flow of sewage. It in one of new solutions, because up till now configuration with vertical bed situated at front of biological part of treatment was applied.The evaluation of object performance was...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublicationDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Light-Powered Starter for Micro-Power Boost DC–DC Converter for CMOS Image Sensors
PublicationThe design of a starter for a low-voltage, micro-power boost DC–DC converter intended for powering CMOS image sensors is presented. A unique feature of the starter is extremely low current, below 1 nA, supplying its control circuit. Therefore, a high-voltage (1.3 V) configuration of series-connected photovoltaic diodes available in a standard CMOS process or a small external LED working in photovoltaic mode can be used as an auxiliary...
-
A Wind Energy Conversion System Based on a Generator with Modulated Magnetic Flux
PublicationIn this work, the concept of an energy conversion system for wind turbines based on the modified permanent magnet synchronous generator (PMSG) is presented. In the generator, a pair of three-phase windings is used, one of which is connected in a “star” and the second in a “delta” configuration. At the outputs of both windings, two six-pulse uncontrolled (diode) rectifiers are included. These rectifiers are mutually coupled by a...
-
Detection system for optical coherence tomography: Czerny-Turner spectrometer
PublicationResearch methods based on spectral analysis have powerful impact on development in many field of science. Signal spectrum can be a source of useful and important data. It enables to obtain information about physical and chemical properties of tested materials. This paper has been devoted to describe optical design for high resolution spectrometer, which is significant element of optical coherence tomography (OCT) systems. Designed...
-
Single-phase, Five-level Inverter with SPWM-Based Neutral Point Voltage Balancing Scheme
PublicationMultilevel inverter topologies provide several advantages over two-level inverter configuration. These benefits are the reason for the growing interest in multilevel topologies among research society. One of the most popular topological concepts (diode and active switch clamping) requires neutral-point potential balancing due to series-connected capacitor banks across the input dc link in such derived inverter configurations. This...
-
QUASI-DISTRIBUTED NETWORK OF LOW-COHERENCE FIBER-OPTIC FABRY-PÉROT SENSORS WITH CAVITY LENGTH-BASED ADDRESSING
PublicationDistributed measurement often relies on sensor networks. In this paper, we present the construction of low coherent fiber-optic Fabry-Pérot sensors connected into a quasi-distributed network. We discuss the mechanism of spectrum modulation in this type of sensor and the constraints of assembly of such sensors in the network. Particular attention was paid to separate the signals from individual sensors, which can be achieved by...
-
Collision-free network exploration
PublicationMobile agents start at different nodes of an n-node network. The agents synchronously move along the network edges in a collision-free way, i.e., in no round two agents may occupy the same node. An agent has no knowledge of the number and initial positions of other agents. We are looking for the shortest time required to reach a configuration in which each agent has visited all nodes and returned to its starting location. In...
-
Proceedings of the 9th International Conference on Structural Dynamics, EURODYN 2014
PublicationSince offshore wind turbine supporting structures are subjected to dynamic environments with time-varying loading conditions, it is important to model their dynamic behavior and validate these models by means of vibrational experiments. In this paper assessment of dynamical state of the structure is investigated by means of both: numerical modeling, and experimental modal analysis. In experimental modal analysis, capturing the...
-
Guided waves for monitoring of plate structures with linear cracks of variable length
PublicationDamage occurring at the work of plate structures may grow to a considerable size. The joint action – the detection of a defect at the earliest possible stage, the monitoring of its growth and the determination of its critical size in the context of structural reliability allows optimizing the cost of the maintenance and repair of structural elements. Thus the development of monitoring systems for permanent observation of fault...
-
Highly linear CMOS triode transconductor for VHF applications
PublicationA high-speed, fully balanced complementary-symmetry metal-oxide-semiconductor (CMOS) triode transconductor is presented. The proposed approach exploits a pseudo-differential-pair triode configuration with a simple adaptive circuit stabilising the drain-to-source voltages of metal-oxide-semiconductor (MOS) transistors. Since no additional active circuits (apart from the resistors made of the cut-off MOS devices) and no feedback...
-
Effect of Compounding Conditions on Static and Dynamic Mechanical Properties of High Density Polyethylene/Ground Tire Rubber Blends
PublicationSearching for new and cost-effective methods of waste rubber recycling is a subject of research in many scientific centers in the world. In this paper there are presented results of the research of the extrusion process of cheap and environmentally friendly thermoplastic compositions containing 50 % wt. of masses of ground tire rubber (GTR). The aim of this study was to determine the relationship between the mixing conditions and...
-
Reliability data safety instrumented systems SIS from the functional safety analysis example critical instalation
Open Research DataThe dataset represents the results of an example of functional safety analysis systems is presented below. It is based on a control system, which consists of some basic components like sensors, programmable logic controllers and valves. It is a part of petrochemical critical installations. The communication between sensor logic controllers and actuators...
-
Testbed analysis of video and VoIP transsmission performance in IEEE 802.11 b/g/n networks
PublicationThe aim of the work is to analyze capabilities and limitations of different implementations of IEEE 802.11 technologies (IEEE 802.11 b/g/n), utilized for both video streaming and VoIP calls directed to mobile devices. Our preliminary research showed that results obtained with currently popular simulation tools can be drastically different than these possible in real-world environment, so, in order to correctly evaluate performance...
-
PROGRAMMABLE YANG - BASED INTERFACE IN CONTROL OF OPTICAL TRANSPORT NETWORK
PublicationSince over a decade we observe intensive effort of research institutions and industrial consortia on extending flexibility and automation of the transport network control also known under the term network programmability. Key aspect of each programming interface is ability to evolve but also sensitivity to future modifications. As indicated in the past work in the specific context of optical transport networks an important criterion...
-
Analyzing energy/performance trade-offs with power capping for parallel applications on modern multi and many core processors
PublicationIn the paper we present extensive results from analyzing energy/performance trade-offs with power capping observed on four different modern CPUs, for three different parallel applications such as 2D heat distribution, numerical integration and Fast Fourier Transform. The CPU tested represent both multi-core type CPUs such as Intel⃝R Xeon⃝R E5, desktop and mobile i7 as well as many-core Intel⃝R Xeon PhiTM x200 but also server, desktop...
-
Pulse-Width Modulation Template for Five-Level Switch-Clamped H-Bridge-Based Cascaded Multilevel Inverter
PublicationThis article presents a carrier-based pulse-width modulation (PWM) template for a 5-level, H bridge-based cascaded multilevel inverter (MLI). The developed control concept generates adequate modulation template for this inverter topology wherein a sinusoidal modulating waveform is modified to fit in a single triangular carrier signal range. With this modulation approach, classical multiplicity and synchronization of the triangular...
-
Set of Experience and Decisional DNA: Experience-Based Knowledge Structures
PublicationThis chapter presents a description of Set of Experience Knowledge Structure (SOEKS) and Decisional DNA (DDNA), argumentation for a knowledge representation, composition, configuration and metrics. SOEKS is a combination of filtered and amalgamated information obtained from formal decision events. It facilitates effective explicit representation of decisional experience taken from different technologies. SOEKS comprises variables,...
-
Analysis of Induced Voltages and Power Losses in High Voltage Power Cables for Selected Methods of Cables Sheaths Bonding
PublicationPower is increasingly supplied to city centres with 110 kV cable lines. This is a convenient way to supply power, and practically the only one possible in areas of dense urban development. A high-voltage cable contains a coaxial metallic sheath, in which in normal operation and in fault conditions (during short-circuits) significant line-to-earth voltages can be induced, which threatens electric shock and/or damage to the cable’s...
-
Organic Vapor Sensing Mechanisms by Large-Area Graphene Back-Gated Field-Effect Transistors under UV Irradiation
PublicationThe gas sensing properties of graphene back-gated field-effect transistor (GFET) sensors toward acetonitrile, tetrahydrofuran, and chloroform vapors were investigated with the focus on unfolding possible gas detection mechanisms. The FET configuration of the sensor device enabled gate voltage tuning for enhanced measurements of changes in DC electrical characteristics. Electrical measurements were combined with a fluctuation-enhanced...
-
Shielded HMSIW-Based Self-Triplexing Antenna With High Isolation for WiFi/WLAN/ISM Band
PublicationThis article presents a novel design of a miniaturized self-triplexing antenna (STA) based on the shielded half-mode substrate integrated waveguide (S-HMSIW) for WiFi/WLAN/ISM-band applications. The S-HMSIW is constructed by assembling one row of vias and an open slot at the open-ended side of the conventional HMSIW. This configuration increases the quality factor and minimizes unwanted radiation loss, which allows for achieving...
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublicationThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...
-
Programmable Input Mode Instrumentation Amplifier Using Multiple Output Current Conveyors
PublicationIn this paper a programmable input mode instrumentation amplifier (IA) utilising second generation, multiple output current conveyors and transmission gates is presented. Its main advantage is the ability to choose a voltage or current mode of inputs by setting the voltage of two configuration nodes. The presented IA is prepared as an integrated circuit block to be used alone or as a sub-block in a microcontroller or in a field...
-
Numerical Comparison of Damping Amplification Effects Obtained in Neighborhood of a Mechanism Singular Position - Viscous and Electromagnetic Cases
PublicationIn the paper, results of numerical investigations are presented. A continuous beam is considered as the main vibrating element. Two energy dissipations methods are compared: viscous dampers and DC generators. To increase the damping effectiveness, velocity amplification is proposed, i.e., a mechanism is introduced between the beam and the damping element, and the mechanism configuration is set as closed to the singular position...
-
SDN testbed for validation of cross-layer data-centric security policies
PublicationSoftware-defined networks offer a promising framework for the implementation of cross-layer data-centric security policies in military systems. An important aspect of the design process for such advanced security solutions is the thorough experimental assessment and validation of proposed technical concepts prior to their deployment in operational military systems. In this paper, we describe an OpenFlow-based testbed, which was...
-
Acoustic imaging of selected areas of Gdansk Bay with the aid of parametric echosounder and side-scan sonar
PublicationThe article presents and analyses the data recorded during sounding of the Gdansk Bay seabed with the aid of a parametric echosounder and a side-scan sonar. The accuracy of seabed structure examination, as a condition for obtaining valuable results, requires correct configuration of echolocation devices and proper calibration of peripheral devices, such as the survey unit geographical position sensor – GPS, the navigation unit,...
-
Synthesis and antimicrobial activity of amino acid and peptide derivatives of mycophenolic acid
PublicationThe series of 16 novel amino acid and peptide mycophenolic acid (MPA) derivatives was obtained as potential antibacterial agents. Coupling of MPA with respective amines was optimized with condensing reagents such as EDCI/DMAP and T3P/TEA. Amino acid analogs were received both as methyl esters and also with the free carboxylic group. The biological activity of the products was tested on five references bacterial strains: Klebsiella...
-
A Developer's View of Application Servers Interoperability
PublicationThe paper describes analysis of application servers interoperability that considers both the available level of integration and the required level of development complexity. Development complexity ranges from simple GUI operations to changes of undocumented features in configuration files. We verify if an integration can be established on a given level of development complexity, rather than verify if it is objectively feasible....
-
Synthesis of Combretastatin A-4 Analogs and their Biological Activities
PublicationCombretastatin A-4 (CA-4) is a natural product, which consists of two phenyl rings, linked by an ethylene bridge. CA-4, inhibitor of polymerization of tubulin to microtubules, possesses a strong antitumor and anti-vascular properties both in vitro and in vivo. Previous studies showed that disodium phosphate salt of CA-4, a water-soluble prodrug is well tolerated at therapeutically useful doses. However, it should be noted that...
-
Hydrodron — New Step for Professional Hydrography for Restricted Waters
PublicationHydrographic surveys in restricted areas are becoming increasingly important, but often impossible to carry out with conventional hydrographic vessels. Presumably in this case an employment of unmanned vehicles is the only reasonable solution. As restricted water areas include, among others: harbours, roadsteads, rivers or lakes. The HydroDron platform, due to its mobility, can operate in the above-mentioned areas. It is adapted...
-
Minichannel and minigap classification criteria based on the aspect ratio of the minigeometry: A numerical study
PublicationA detailed numerical investigation has been carried out to analyze the diabatic flow distribution and velocity profile in 18 minigeometries with various aspect ratios for V-type and I-type flow configurations (for 36 cases) assuming ethanol as a working fluid. The aim of the study is to distinguish the value of the aspect ratio for which the flow in minigeometry starts to be two-dimensional (minigap). Cases with a constant Reynolds...
-
Fabrication and Crystal Structure of Sol-Gel Deposited BST Thin Films with Compositional Gradient
PublicationIn the present research technology of compositionally graded barium strontium titanate Ba1-xSrxTiO3 thin films deposited on stainless steel substrates by sol-gel spin coating followed with thermal annealing at T = 650°C is reported. Results of thermal behavior of the sol-gel derived powders with compositions used for fabrication of graded structure (i.e. with Sr mole fraction x = 0.5, 0.4 and 0.3) are described. X-ray diffraction...
-
A Simple-Topology Compact Broadband Circularly Polarized Antenna With Unidirectional Radiation Pattern
PublicationIn this letter, a geometrically simple, reflector-backed single-point-fed circularly polarized (CP) antenna with unidirectional radiation pattern is presented. The structure comprises a simple coplanar waveguide (CPW) feeding circuit with an open slot etched on one side of the coplanar ground. The enhanced CP bandwidth is obtained by combining the loop mode, the slot mode, and the asymmetrical configuration of the coplanar ground...
-
High load capacity spur gears with conchoidal path of contact
PublicationThe present study is devoted to investigation of spur gears with a conchoidal path of contact and a convex-convex contact between teeth. The load capacity and energy efficiency were evaluated using both theoretical and experimental approaches. The theoretical analysis showed that the conchoidal gear pairs are 5–21% stronger in terms of contact stress and have similar energy efficiency as compared to the involute gear pairs of the...
-
Optimisation of cooperation of hybrid renewable energy sources with hydrogen energy storage toward the lowest net present cost
PublicationThe paper presents the results of a technical and economic analysis of the power supply for a model industrial facility based on intermittent renewable energy sources in the form of wind turbines and photovoltaic modules, supplemented with hydrogen energy storage. The adopted power supply strategy assumed the maximisation of self-consumption of self-produced electricity. Six variants were considered, including two with an energy...
-
Performance and Energy Aware Training of a Deep Neural Network in a Multi-GPU Environment with Power Capping
PublicationIn this paper we demonstrate that it is possible to obtain considerable improvement of performance and energy aware metrics for training of deep neural networks using a modern parallel multi-GPU system, by enforcing selected, non-default power caps on the GPUs. We measure the power and energy consumption of the whole node using a professional, certified hardware power meter. For a high performance workstation with 8 GPUs, we were...
-
Impact of the Artificial Strait in the Vistula Spit on the Hydrodynamics of the Vistula Lagoon (Baltic Sea)
PublicationIn the Vistula Lagoon, storm surges are induced by variable sea levels in the Gulf of Gdańsk and wind action. The rising of the water level in the southern part of the basin, exceeding 1.0 m above mean sea level, can be dangerous for the lowland area of Żuławy Elbląskie, causing the inundation of the polders adjacent to the lagoon. One of the potential possibilities to limit the flood risk is to decrease the water level in the...
-
Comprehensive thermodynamic analysis of the CAES system coupled with the underground thermal energy storage taking into account global, central and local level of energy conversion
PublicationA key aspect of CAES is the optimal configuration of the thermodynamic cycle. In this paper, the situation of cooperation between the current conventional power plants and wind farms is analyzed, and then, based on thermodynamic models, the process of storing thermal and electrical energy in the CAES system coupled with a heat storage and recovery is developed. Therefore, three levels can be distinguished, namely: the global level...
-
Fractionation and origin of dissolved and colloidal organic nitrogen in BNR plant effluent
PublicationThe characteristics of effluent dissolved and colloidal organic nitrogen (DON and CON) as well as their origin, fate and biodegradability in wastewater treatment plants and receiving waters were identified as the major issues that limit the ability to achieve low total N in the effluent. This study presents the results of a comprehensive survey, which was conducted in eight biological nutrient removal (BNR) WWTPs in northern Poland....
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublicationIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...
-
Simulations of wave propagation and attenuation in fields of colliding ice floes
Open Research DataThis dataset contains results of numerical smulations of sea ice-wave interactions, corresponding to laboratory experiments conducted at the Large Ice Model Basin (LIMB) at the Hamburg Ship Model Basin (HSVA) as part of the LS-WICE ("Loads on Structure and Waves in Ice"; https://zenodo.org/record/1067170#.XrLt_dhpxhE) project. THe simulations were conducted...
-
Performance Analysis of Multicast Video Streaming in IEEE 802.11 b/g/n Testbed Environment
PublicationThe aim of the work is to analyse capabilities and limitations of different IEEE 802.11 technologies (IEEE 802.11 b/g/n), utilized for both multicast and unicast video streaming transmissions directed to mobile devices. Our preliminary research showed that results obtained with currently popular simulation tools can be drastically different than these possible in real-world environment, so, in order to correctly evaluate performance...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublicationBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublicationEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
The Way One Defines Specification Matters: On the Performance Criteria for Efficient Antenna Optimization in Aggregated Bi-Objective Setups
PublicationDesign of antenna structures for real-world applications is a challenging task that often involves addressing multiple design requirements at a time. Popular solution approaches to this class of problems include utilization of composite objectives. Although configuration of such functions has a significant effect on the cost and performance of the optimization, their specific structure is normally determined based on engineering...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublicationThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
Cascaded Buck Hybrid Interlink Converter for Multiple-Input / Multiple-Output Operation
PublicationThe provision of isolated- and non-isolated DC output voltages by Power electronics power-conditioning devices in the recent ‘green-energy-revolution’ era is on course. In this paper, a structure for multi-input multi-output(MIMO) DC–DC buck converter is proposed to generate output voltages of varying levels with fewer component-count. The DC output voltage of each of the constituting buck converters can be used independently or...
-
Direction-of-Arrival Estimation Methods in Interferometric Echo Sounding
PublicationNowadays, there are two leading sea sounding technologies: the multibeam echo sounder and the multiphase echo sounder (also known as phase-dierence side scan sonar or bathymetric side scan sonar). Both solutions have their advantages and disadvantages, and they can be perceived as complementary to each other. The article reviews the development of interferometric echo sounding array configurations and the various methods applied...
-
Electron Scattering from Methyl Formate (HCOOCH3): A Joint Theoretical and Experimental Study
PublicationElastic low-energy electron collisions with methyl formate have been studied theoretically at the level of various theories. The elastic integral cross section was calculated using Schwinger multichannel and R-matrix methods, in the static-exchange and static-exchange plus polarization levels of approximations for energies up to 15 eV. The absolute total cross section for electron scattering from methyl formate has been measured...
-
Canonical switched capacitor converters. Comments, complements, and refinements
PublicationSwitched Capacitor Converters (SCC) form useful blocks in low/medium power applications as they are suitable for integration, both as off-chip and on-chip IC realizations. However, the problem with SCC is that their voltage conversion ratio is topology-dependent. By changing the SC circuit configuration, we can gain control over voltage conversion but the available ratio remains of a discrete nature, i.e. it maps into a countable...