displaying 1000 best results Help
Search results for: UNIAXIAL COMPRESSIVE STRENGTH
-
Reliability of Corroded Stiffened Plate Subjected to Uniaxial Compressive Loading
PublicationThe work is focused on the reliability of corroded stiffened plates subjected to compressive uniaxial load based on the progressive collapse approach as stipulated by the Common Structural Rules for Bulk Carriers and Oil Tankers, employing the limit state design. Two different cases have been investigated. In the first model, the corrosion degradation led to uniform thickness loss, whereas the mechanical properties were unchanged,...
-
Compressive Strength and Leaching Behavior of Mortars with Biomass Ash
Publication -
Analysis of ultimate compressive strength of cracked plates with the use of DOE techniques
PublicationThe objective of this work is to investigate the structural compressive response of plates with locked cracks accounting for all relevant factors and correlation between them. The nonlinear FE model considering both geometric and material nonlinearities is employed herein, and the FE model of the structural response of intact plates is validated with the available experimental data. In the common studies, based on One Factor at...
-
Ultimate compressive strength assessment of uncleaned and cleaned corroded plates with locked crack
PublicationThe work presented here investigates the structural response of cleaned corroded plates, subjected to compressive load in the presence of a locked crack, where the change of mechanical properties as a result of corrosion development and the cleaning process is also accounted for. A Finite Element model for assessing the compressive strength, considering geometric and material nonlinearities, is developed, and the analysed plates...
-
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublicationThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
Advanced numerical modelling for predicting residual compressive strength of corroded stiffened plates
PublicationAn advanced methodology for predicting the residual compressive strength of corroded stiffened plates is developed here using the non-linear finite element method. The non-uniform loss of a plate thickness is accounted for on a macro-scale. In contrast, mechanical properties are changed using the constitutive model to reflect the corrosion degradation impact on a micro-scale. Three different stiffened plate thicknesses are considered,...
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublicationThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
Ultimate strength of stiffened plates subjected to compressive load and spatially distributed mechanical properties
PublicationThe present study deals with the ultimate strength of stiffened plates subjected to spatially distributed mechanical properties and compressive load. Normally, mean values of mechanical properties based on tensile tests are used to validate the numerical assessment with experimental results. However, mechanical properties may vary within a single specimen. To investigate the impact of that, random fields of yield stress and Young...
-
Isothermal Calorimetry and Compressive Strength Tests of Mortar Specimens for Determination of Apparent Activation Energy
PublicationThe hydration process of cementitious materials involves a thermally activated reaction that depends on the composition of the mixture and the curing temperature. The main parameter affecting the temperature variation of cast-in-place concrete is the apparent activation energy, which can be used for the efficient prediction of the temperature evolution and maturity index of hardening concrete. This paper discusses two methods to...
-
Feature Importance of Stabilised Rammed Earth Components Affecting the Compressive Strength Calculated with Explainable Artificial Intelligence Tools
Publication -
Predicting Compressive Strength of Cement-Stabilized Rammed Earth Based on SEM Images Using Computer Vision and Deep Learning
Publication -
Compressive strength and density of cement pastes containing iron oxide (Fe3O4) nanoparticles (nanomagnetite)
Open Research Data*.ODS - open-data source spreadsheet - Dataset presenting:
-
Effect of mixing method and particle size on hardness and compressive strength of aluminium based metal matrix composite prepared through powder metallurgy route
Publication -
Rheological and compressive strength (ultrasonic pulse method) properties of cement pastes containing iron oxide (Fe3O4) nanoparticles
Open Research DataRheological data of cement pastes containing different replacement levels of cement with iron oxide nanoparticles deterimined using MCR 301 (Anton Paar) stress-imposed rheometer, equipped with calibrated helicoidal geometry
-
Low temperature cracking equipment: Termal Stress Restrained Specimen Test (TSRST); Uniaxial Tensile Strength Test (UTST); Tensile Creep Test (TCT); Relaxation Test (RT);
Research Equipment -
Effect of coarse grain aggregate on strength parameters of two-stage concrete
Publication. Two-stage concrete (TSC) is a special type of concrete that the method of its construction and implementation is different from conventional one. In TSC, coarse aggregate particles are first placed in the formwork and voids between them are subsequently injected with a special cementations mixture. TSC has been successfully used in many applications, such as underwater construction, casting concrete sections congested with reinforcement...
-
Experimental and numerical investigations of ultimate strength of imperfect stiffened plates of different slenderness
PublicationThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive...
-
Drill holes decrease cancellous bone strength: A comparative study of 33 paired osteoporotic human and 9 paired artificial bone samples
PublicationThis study was designed to compare compressive strength of cancellous bone retrieved from the femoral head in a specimen with and without guide wire hole, with comparison to synthetic bone samples. Femoral heads retrieved from 33 patients who sustained femoral neck fractures and underwent hip arthroplasty were cut into cuboids leaving two matching samples from the same femoral head. Similar samples were prepared from synthetic femurs....
-
Effect of free water on the quasi‑static compression behavior of partially‑saturated concrete with a fully coupled DEM/CFD approach.
PublicationThe work aims to numerically investigate the quasi-static response of partially fluid-saturated concrete under two-dimensional uniaxial compression at the mesoscale. We investigated how the impact of free pore fluid content (water and gas) affected the quasi-static strength of concrete. The totally and partially fluid-saturated concrete behavior was simulated using an improved pore-scale hydro-mechanical model based on DEM/CFD....
-
OCENA NOŚNOŚCI STAREGO MOSTU ŁUKOWEGO W JAGODNIKU
PublicationArtykuł opisuje przeprowadzoną analizę statyczno-wytrzymałościowa 95-letniego betonowego mostu łukowego zlokalizowanego w Jagodniku w północnej Polsce. Trwałość i wytrzymałość starego betonu są określane na podstawie wybranych właściwości mechanicznych, fizycznych i chemicznych. Program badań laboratoryjnych składał się z następującego zestawu badań: pomiary głębokości strefy skarbonatyzowanej i gęstości w stanie suchym, badania...
-
Experimental study and numerical simulation of the dynamic penetration into dry clay
PublicationTests of dry clay were carried out in a uniaxial stress state using the experimental setup which implements the split Hopkinson pressure bar method. Based on the results of these experiments, the compressive strength of clay was determined as an important element of S.S. Grigoryan’s model of the soil medium. In addition, the parameters of this model are determined from the results of experiments using the modified Kolsky method...
-
Simple empirical formula to estimate the main geomechanical parameters of preplaced aggregate concrete and conventional concrete
PublicationPreplaced aggregate concrete (PAC) or two-stage concrete is a specific type of concrete successfully employed in many projects including underwater concrete structures, massive concrete structures, structures made of reinforced concrete, and improvement of concrete structures. PAC is significantly different than the conventional concrete. In this type of concrete, aggregates are initially poured into the mold, the voids between...
-
Mechanical properties of cement pastes containing pristine and silica-coated bismuth oxide (Bi2O3) and gadolinium oxide (Gd2O3) structures
Open Research DataExcel file containing raw mechanical (compressive strength) data of cement pastes containing variable amount of Bi2O3, Gd2O3, Bi2O3-SiO2 and Gd2O3-SiO2 structures. Sample designation in the Excel file is in line with sample designation in the manuscript associated with dataset.
-
Source code - AI models (MLM1-5 - series I-III - QNM opt)
Open Research DataSource code - AI models (MLM1-5 - series I-III - QNM opt) for the paper "Computational Complexity and Its Influence on Concrete Compressive Strength Prediction Capabilities of Machine Learning Models for Concrete Mix Design Support" accepted for publication.
-
Mechanical properties of cement pastes containing pristine and silica-coated bismuth oxide Bi2O3+Gd2O3 structures
Open Research DataExcel (*.xlsx) and Csv (*.csv) files containing raw mechanical (compressive strength) data of cement pastes after 1, 2, 7 and 28 days of curing
-
Multi-functional monodispersed SiO2-TiO2 core-shell nanostructure and TEOS in the consolidation of archaeological lime mortars surfaces
PublicationArchaeological traditional lime mortars are susceptible to many environmental conditions such as the impact of water (rain, humidity, groundwater, etc.), variation of temperatures' degrees, wind and/or pollution. Accordingly, this research aims to provide newly assessed multifunctional Nano-coating for the purpose of archaeological lime mortar protection. For this, the study combined physicochemical and mechanical characterizations...
-
Mechanical properties of concrete mixes M0-M100 concrete mixes
Open Research DataDataset of hardneded properties of concretes containing different amount of magnetite aggregate (M0-M100) mixes.Excel file consists results of:
-
Właściwości termoizolacyjne kompozytu wapienno-cementowego z udziałem paździerzy konopnych=Thermal insulation properties of the lime-cement composite with hemp shives
PublicationPrzedstawiono wyniki badań kompozytów wykonanych na bazie wapna budowlanego, cementu i dolomitu - spoiwa wiążącego z udziałem paździerzy konopi. Określono ich podstawowe właściwości, tj.: gęstość objętościową, współczynnik przewodzenia ciepła oraz wytrzymałości na ściskanie. Otrzymane wyniki dowodzą, że wytworzone kompozyty wapienno-cementowe z udziałem paździerzy konopnych są lekkie i charakteryzują się niskim współczynnikiem...
-
Wykładnicze równanie Arrheniusa jako funkcja dojrzałości twardniejącego betonu
PublicationPoprawne określenie funkcji dojrzałości dla mieszanki betonowej warunkuje powodzenie szacowania wytrzymałości na ściskanie na bazie pomiarów temperatury in situ. W artykule omówiono zastosowanie równania Arrheniusa do opisu funkcji dojrzewania twardniejącego betonu. Szczególną uwagę zwrócono na zależności szybkości zachodzenia reakcji w odmiennych warunkach temperaturowych. Przedstawiono wyniki własnych badań na kostkach zaprawy...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublicationWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Materiały stosowane do wytwarzania implantów kości
PublicationMateriały stosowane do wytwarzania implantów kostnych muszą być biokompatybilne, nietoksyczne, bioaktywne oraz wykazywać odpowiednie właściwości mechaniczne, takie jak wytrzymałość na ściskanie, na zginanie oraz sztywność i twardość. Gama stosowanych materiałów jest bardzo szeroka, obejmuje metale, polimery, ceramikę oraz ich kompozyty. Każdy z tych materiałów ma swoje mocne i słabe strony. Praca stanowi przegląd materiałów stosowanych...
-
Effect of particle size of aluminosilicate microspheres on the change of hydration heat of cement mortars and selected physical, chemical, and mechanical properties.
Open Research DataThis subject of the work is the study of selected properties of cement mortars containing two fractions of aluminosilicate microspheres with grain size in the range of 125 to 250 μm and from 250 to 500 μm. Mortar mixtures with ordinary Portland cement (OPC 42.5R) and three substitution rates of cement by microspheres, 1.5%, 3.5%, and 5.0%, were investigated....
-
2022-2023 - Wytrzymałość materiałów I, PG_00039799
e-Learning CoursesCelem przedmiotu jest zapoznanie studentów z podstawowymi zagadnieniami związanymi z wytrzymałością materiałów. Wykłady dotyczą kolejno: podstawy wytrzymałości materiałów, wytrzymałość pręta prostego na ściskanie/rozciąganie, analiza wytrzymałości dla układów prętowych statycznie niewyznaczalnych, wytrzymałość prętów na skręcanie, wytrzymałość belek zginanie, odkształcenia belki zginanej, ścinanie pręta (pręt ścinany), stany naprężeń,...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublicationThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
FE analysis of support-specimen interaction of compressive experimental test
PublicationThe objective of this work is to investigate the support-specimen interaction during the compressive experimental testing of stiffened plates. The interaction is analyzed employing the nonlinear Finite Element Method using the commercial software ANSYS. The connection between the stiffened plate and testing supports is modelled with the use of contact elements, where several possible interaction scenarios are investigated, and...
-
Mechanical properties of Precontraint 1202 S2 based on uniaxial tensile and creep tests
PublicationThe purpose of the paper is the estimation of the polyvinyl chloride – polyester-coated fabric (Precontraint 1202 S2) mechanical properties under uniaxial tensile tests as well as short- and long-time creep tests. The uniaxial tests are the basis of non-linear elastic description while the creep tests are used for the evaluation of the stiffness parameters in time and for the identification of the standard viscoelastic model. The...
-
STRENGTH of MATERIALS TOWARDS APPLICATIONS (2024)
e-Learning CoursesThe SMTA DATE Course consists of the following problems to be discussed during the lectures: - Introduction to strength of materials towards applications - Fundamentals of modelling in strength of materials towards applications - Materials and basic structures - Fundamentals of modelling in strength of materials towards applications - Definition of environment and loads - General, energy-based and advanced methods for analysis...
-
Effects of Xanthan Gum Biopolymer on the Permeability, Odometer, Unconfined Compressive and Triaxial Shear Behavior of a Sand
PublicationBiopolymers, which are microbially induced polymers, can be used as an alternative material to improve engineering performance of soils. In this paper, a laboratory study of 0.075-1.0 mm size sand and biopolymer (i.e., xanthan gum) mixtures with various mix ratios (0%, 0.5%, 1.0%, and 1.5%) was performed. The materials, specimen preparation, and test methods are described, as are the results of a suite of permeability, odometer, unconfined...
-
Assessment of Tensile Strength Reserve of Asphalt Mixtures at Low Temperatures
PublicationDuring winter conditions, low-temperature cracks develop at the surface of the asphalt pavement when tensile thermal stress induced in the asphalt layer during cooling equals and exceeds the tensile strength of the material. The paper presents the results of tensile strength reserve assessment of asphalt mixtures with neat and SBS-polymer modified bitumen application. The tensile strength reservewas calculated as difference between...
-
A Proposed Soft Computing Model for Ultimate Strength Estimation of FRP-Confined Concrete Cylinders
PublicationIn this paper, the feed-forward backpropagation neural network (FFBPNN) is used to propose a new formulation for predicting the compressive strength of fiber-reinforced polymer (FRP)-confined concrete cylinders. A set of experimental data has been considered in the analysis. The data include information about the dimensions of the concrete cylinders (diameter, length) and the total thickness of FRP layers, unconfined ultimate concrete...
-
Maturity curve for estimating the in-place strength of high performance concrete
PublicationThe paper presents the maturity curve for estimating the in-place early-age compressive strength of concrete. The development of appropriate maturity curve is a complex process. It is important to correctly determine the datum temperature and activation energy, which can be obtained in mortar tests. This paper describes an investigation of the accuracy of the maturity method to estimate the strength when different way to rate constant...
-
Numerical and experimental study on effect of boundary conditions during testing of stiffened plates subjected to compressive loads
PublicationThis study analyses the effect of boundary conditions during testing on the structural behaviour stiffened plates with different thicknesses subjected to compressive loads. The goal of the compressive tests is to analyse the ultimate strength of a stiffened plate. During the test, relevant physical quantities are measured and investigated. The supporting structure's behaviour is investigated by analysing the force-displacements...
-
Influence of water soaking on the ultimate tensile strength of polyester-based coated woven fabrics
PublicationThis research aims to determine the influence of water-soaking on polyester-based coated woven fabrics for ultimate tensile strength and elongation at break under uniaxial tensile tests. The paper begins with a short survey of literature concerning the investigation of the determination of coated woven fabric properties. The authors carried out the uniaxial tensile tests with an application of a flat grip to establish the values...
-
Mechanical properties of the human stomach under uniaxial stress action
PublicationThe aim of this study was to estimate the range of mechanical properties of the human stomach in order to use the collected data in numerical modelling of surgical stapling during resections of the stomach. The biomedical tests were conducted in a self-developed tensile test machine. Twenty-two fresh human stomach specimens were used for the experimental study of its general strength. The specimens were obtained from morbidly obese...
-
Compressive Sensing Approach to Harmonics Detection in the Ship Electrical Network
PublicationThe contribution of this paper is to show the opportunities for using the compressive sensing (CS) technique for detecting harmonics in a frequency sparse signal. The signal in a ship’s electrical network, polluted by harmonic distortions, can be modeled as a superposition of a small number of sinusoids and the discrete Fourier transform (DFT) basis forms its sparse domain. According to the theory of CS, a signal may be reconstructed...
-
Polyester sail technical woven fabric behaviour under uniaxial and biaxial tensile tests
PublicationThe paper is focused on the identification of mechanical properties of a sail technical woven fabric (yacht sailcloth polyester) style 480 AP with MTO (Medium Tempered Optimized) finish. The non-linear elastic behaviour of the fabric applied for sails is investigated under uniaxial and biaxial tensile tests. Comparison of non-linear elastic parameters with others polyester coated fabrics is made. This paper is intended to be an...
-
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublicationThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
Analysis of compressive forces in CFGFT cylindrical pillars and their coatings using laboratory tests and metric spaces
PublicationThe article discusses compressive forces tests in composite-concrete pillars with the use of laboratory active experiment including the factors and properties of materials which have a significant impact on the test results and their repeatability. A polymer composite based on glass fiber reinforced resin with different fiber beam angles (20, 55 and 85) was used as a buffer/coat of the pole. Due to the problems with direct comparison...
-
Signal Reconstruction from Sparse Measurements Using Compressive Sensing Technique
PublicationThe paper presents the possibility of applying a new class ofmathematical methods, known as Compressive Sensing (CS) for recovering thesignal from a small set of measured samples. CS allows the faithful recon-struction of the original signal back from fewer random measurements bymaking use of some non-linear reconstruction techniques. Since of all thesefeatures, CSfinds its applications especially in the areas where, sensing is...
-
Verification of Selected Calculation Methods Regarding Shear Strength in Reinforced and Prestressed Concrete Beams
PublicationThe purpose of this article was an attempt to compare selected calculation methods regarding shear strength in reinforced and prestressed concrete beams. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008 [1], ACI 318- 14 [2] and fib Model Code for Concrete Structures 2010 [3]. The analysis also consists of methods published in technical literature. Calculations of shear strengths were made based...
-
Discrete element method simulations of fracture in concrete under uniaxial compression based on its real internal structure
PublicationThe paper describes experimental and numerical results of concrete fracture under quasi-static uniaxial compression. Experimental uniaxial compression tests were performed on concrete cubic specimens. Fracture in concrete was detected at the aggregate level by means of three non-destructive methods: three-dimensional X-ray microcomputed tomography, two-dimensional scanning electron microscope and manual two-dimensional digital...
-
Strength testing machine results
Open Research DataThe aim of the research project is to determine the rotational stiffness of the connection between the purlin and the part of the truss top chord. The attached files are referred to the forces and displacements obtained from the strength testing machine (two sensors). The 16 specimens were tested on the experimental set up.
-
Design of experiments approach for ultimate strength assessment of corroded stiffened plates
PublicationThe impact of corrosion degradation on the ultimate strength of stiffened plates subjected to compressive loading is investigated. The DoE technique is used considering different plate and column slenderness ratios and corrosion severity. The FE method, considering geometrical and material nonlinearities, is employed. A two-stage corrosion degradation model is adopted. Firstly, a uniform thickness loss is adopted to reflect the...
-
Impact of Tensile and Compressive Stress on Classical and Acoustic Barkhausen Effects in Grain-Oriented Electrical Steel
PublicationIn this paper, we present the results of the investigation of impact of tensile and compressive stress on the classical Barkhausen effect, magnetoacoustic emission (MAE) signal properties, and B(H) hysteresis loops for grain-oriented (GO) electrical steel. Samples have been glued to a nonmagnetic steel bar and stressed within elastic range (±800 μdef) by means of four-point bending method. The samples were cut out in two directions...
-
Verification of selected calculation methods regarding shear strength in beams without web reinforcement
PublicationThe purpose of the article was to compare selected calculation methods regarding shear strength in reinforced concrete beams without web reinforcement. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008, ACI 318-14 and fib Model Code for Concrete Structures 2010. The analysis also consists of authorial methods published in technical literature. Calculations of shear strengths were made based on experimental...
-
JOURNAL OF STRENGTH AND CONDITIONING RESEARCH
Journals -
Determination of mechanical properties of human stomach tissues subjected to uniaxial stretching
Open Research DataThe aim of the study was to determine the biomechanical properties of the walls of the human stomach. The samples were fragments of the human stomach obtained after sleeve gastrectomy. Samples cut parallel to the stomach curves and perpendicular to the stomach curves were tested in each series. All samples were subjected to uniaxial stretching. During...
-
Modelling of concrete behaviour in uniaxial compression and tension with DEM.
PublicationW artykule omowiono wyniki modelowania betonu podczas jednoosiowego sciskania i rozciagania stosujac metode elementów dyskretnych. Beton zostal opisany jako material 3-fazowy (kruszywo, zaprawa cementowa i strefy kontaktu). Szczegolna uwage zwrocono na zjawiska mikro-strukturalne na poziomie kruszywa (lancuchy sil, wiry, obroty ziaren). Wyniki numeryczne zostaly porownano z wynikami badan doswiadczalnych.
-
Ray-tracing analysis of uniaxial birefringent optical components
PublicationW artykule przedstawiono elgorytm pozwalający na wyznaczenie kierunków i natężeń promieni propagowanych w układach optycznych zawierających elemennty wykonane z jednoosiowych materiałów dwójłomnych. Obliczenia w prezentowanym algorytmie są wykonywane na wektorach w globalnym układzie współprzędnych, eliminując konieczność częstych zmian ukłądu współprzędnych. Jako przykład obliczeniowy przedstawiono pełną analizę propagacji promieni...
-
Study on some of the strength properties of soft clay stabilized with plastic waste strips
PublicationIt is well known that if plastic wastes are not well managed, it has a negative impact on the environment as well as on human health. In this study, recycling plastic waste in form of strips for stabilizing weak subgrade soil is proposed. For this purpose, a weak clay soil sample was mixed with 0.2%, 0.3%, and 0.4% of plastic strips by weight of soil, and the experimental results were compared to the control soil sample with 0%...
-
Edgewise Compressive Behavior of Composite Structural Insulated Panels with Magnesium Oxide Board Facings
PublicationEdgewise compression response of a composite structural insulated panel (CSIP) with magnesium oxide board facings was investigated. The discussed CSIP is a novel multifunctional sandwich panel introduced to the housing industry as a part of the wall, floor, and roof assemblies. The study aims to propose a computational tool for reliable prediction of failure modes of CSIPs subjected to concentric and eccentric axial loads. An advanced...
-
Strength of Materials I,Lectures,DAPE,fall 23-24(PG_00055150)
e-Learning CoursesThe aim of the course is to acquire knowledge referring to the Mechanics of Materials (Strength of Materials)
-
Influence of Bitumen Type and Asphalt Mixture Composition on Low-Temperature Strength Properties According to Various Test Methods
PublicationIn regions with low-temperatures, action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties...
-
Strength of Materials II,Lectures,DAPE,spring 21-22 (PG_00050281)
e-Learning CoursesThe aim of the subject is to acquire knowledge related to the strength of materials II (mechanics of material, part 2)
-
Weldability of high strength steel in underwater environment
PublicationThe article describes the problems with weldability of high-strength steels in the aquatic environment. The tendency of steel S355J2G3 and S500M to form cold cracks when welded in wet welding conditions has been experimentally evaluated. It was found that the tested steels have a high propensity to cracking. An experiment has been proposed and tested to evaluate the usefulness of the tempering bead technique as a method of improving...
-
Strength Fracture and Complexity
Journals -
Problems of Strength and Plasticity
Journals -
STRENGTH AND CONDITIONING JOURNAL
Journals -
Micro‑ and nano‑ bentonite to improve the strength of clayey sand as a nano soil‑improvement technique
PublicationNano-additives results in the formation of nano-cementation (NC). This process is recently used to improve the durability of various building materials. NC used to improve the strength of untreated soil materials, also known as nano soil-improvement (NSI). In few years, the role of nano-additives in various types of soils were developed. In this research, the role of micro- and nano- size of bentonite as soil stabilizer was evaluated...
-
Compaction of freshly pluviated granulates under uniaxial and multiaxial cyclic loading.
Publication.
-
Prediction of cast-in-place concrete strength of the extradosed bridge deck based on temperature monitoring and numerical simulations
PublicationThe work is devoted to the implementation of a monitoring system for high performance concrete embedded in the span of an extradosed bridge deck using a modified maturity method augmented by numerical simulations conducted by the authors’ FEM code. The paper presents all research stages of bridge construction and considers the conclusions drawn from the results of laboratory tests, field measurements, and numerical calculations....
-
The influence of core material on strength properties of hybrid sandwich panels
PublicationAlong with high prices of fuels and more restrictive safety and environmental regulations (including environment protection) increased interest in sandwich structures is being observed. One of the solution having growing application potential is steel sandwich panel. The construction consist of very thin steel plates (about 2mm) and stiffeners between them. The main advantage of using such solution is very high strength to weight...
-
Strength of materials II, Tutorials and Laboratory, DaPE, sem. 04, summer 22/23, (PG_00050281)
e-Learning CoursesTutorials and Laboratory on Strength of materials II.
-
The influence of compressive gear on maximal load lifted in competitive powerlifting.
Publication -
Fatigue strength determination of ship structural joints. Part I - Analytical methods for determining fatigue strength of ship tructures
PublicationSpectacular accidents at sea which have happened for a few last years show that hull structures of contemporary sea-going ships are not perfect and must be systematically improved. Fatigue strength is one of the groups of strength problems which affect design of contemporary ship's structures and greatly contribute in their improvement process. In this paper several approaches to estimation of fatigue life of hull structural...
-
Numerical assessment of ultimate strength of severe corroded stiffened plates
PublicationThe objective of this work is to investigate numerically (using the non-linear FEM and the approach stipulated by the Common Structural Rules) the severe nonuniform corrosion degradation effect on the ultimate strength of stiffened plates and compare the results to the already published experimental works. Different factors governing structural behavior of corroded stiffened plates are investigated, such as corrosion degradation level,...
-
Strength parameters of deltaic soils determined with CPTU, DMT and FVT
PublicationThis paper presents the results of soil investigation in soft, normally consolidated organic soil in the estuary of Vistula river. The analysis concerns clayey mud and peat layers interbedded with loose to medium-dense sands. Several Cone Penetration Tests with pore water measurement (CPTU), Dilatometer Tests (DMT) and Field Vane Tests (FVT) were performed on the testing site. The cone factor Nkt was estimated using the results...
-
Strength of Materials II, Tutorial and Laboratory, DaPE, sem. 04, summer 21/22, (PG_00050281)
e-Learning CoursesThe aim of the course is to present the strength calculations of systems in a complex state load.
-
Weldability of high strength steels in wet welding conditions
PublicationIn this paper are characterized problems of high strength steel weldability in underwater wet welding conditions. Water as a welding environment intensifies action of unfavourable factors which influence susceptibility to cold cracking of welded steel joints. The susceptibility to cold cracking of S355J2G3 steel and S500M steel in wet conditions was experimentally estimated (by using Tekken test). It was concluded that the steels...
-
Experimental and numerical investigations of ultimate strength of degradated structures
PublicationThe presented work investigates the corrosion influence on the structural behaviour of structural elements. Nine welded large-scale stiffened plates, and 30 standard small specimens have been subjected to the accelerated marine immersed conditions. After corrosion testing, the specimens have been accurately measured in terms of surface characteristics. The coupon specimens were furtherly subjected to tensile loading to develop...
-
Mechanical strength of stems in aquatic macrophytes
PublicationSummary: In populations of submerged macrophytes, individuals are selected in terms of resistance to the effect of hydrodynamic forces. The aim of this study was to check whether individuals growing in river water are more tensile and bending resistant than plants occurring in places not exposed to flow stress. We determined the ultimate tensile strength of stems in four macrophyte species, Potamogeton natans, P. pectinatus, Batrachium...
-
INFLUENCE OF PRESERVATIVE ON THE TENSILE STRENGTH OF THE TISSUE OF PORCINE CIRCULATORY SYSTEM
PublicationCurrently one of the leading causes of death worldwide is heart diseases which include calcification of heart valves and vascular aneurysm. There are many biomaterials that can substitute pathologically altered tissue, however, none of them is as perfect as native tissue. Currently, scientists are looking for new biomaterials that can be successfully implanted without exposing the patient to reoperation. Each material introduced...
-
Problems with modelling the strength properties of sailing vessels rigging ropes
PublicationThis article presents the basic parameters of soft ropes: natural fibre ropes, soft wire ropes and synthetic fibre ropes used for running rigging. There are only several materials still used for the production of natural fibre ropes, including cotton, jute, hemp, sisal and manila hemp. The most commonly used soft wire ropes are twisted pair ropes; for smaller diameters there is a 6x19M - FC rope and for larger diameters – 6x37M...
-
Underwater wet welding of S1300 ultra-high strength steel
PublicationMarine Structures Volume 81, January 2022, 103120 Underwater wet welding of S1300 ultra-high strength steel Author links open overlay panelJacekTomkówGrzegorzRogalski https://doi.org/10.1016/j.marstruc.2021.103120 Get rights and content Under a Creative Commons licenseopen access Highlights • Technological method of S1300 steel underwater weldability improving was proposed. • Number of cracks and hardness of welded joints was...
-
Investigations on strength and fracture in RC beams scaled along height or length
PublicationThe objective of the present paper is to identify experimentally and theoretically differing failure mechanisms in reinforced concrete beams subjected to four-point bending for a separate variation of the depth and length at the constant thickness. Experiments were performed on reinforced concrete beams under four-point bending. Different failure mechanisms included steel yielding, diagonal tension or shear- compression depending...
-
Advances in Modelling and Analysis of Strength of Corroded Ship Structures
PublicationThe present study reviews the recent advances in modelling and analyses the strength of corroded ship structures. Firstly, the time-variant methodologies that consider only the mean structural element thickness loss due to corrosion degradation are identified. Corrosion degradation is regarded as the phenomenon that causes uneven thinning of specimens. This has been captured by various researchers as the loss of mechanical properties...
-
Uncertainty assessment of ultimate strength of corroded stiffened plates subjected to different maintenance actions
PublicationThe study deals with the uncertainty assessment of different governing factors related to the ultimate strength of the corroded stiffened plates. The load-carrying capacity is predicted with the use of the nonlinear Finite Element Method. The most influencing governing factors in the non-linear FE analysis, such as material properties and initial imperfections are modeled and analysed as stochastic variables. The ultimate strength...
-
Cold Cracking Of Underwater Wet Welded S355G10+N High Strength Steel
PublicationWater as the welding environment determines some essential problems influencing steel weldability. Underwater welding of high strength steel joints causes increase susceptibility to cold cracking, which is an effect of much faster heat transfer from the weld area and presence of diffusible hydrogen causing increased metal fragility. The paper evaluates the susceptibility to cold cracking of the high strength S355G10+N steel used,...
-
Strength analysis of a large-size supporting structure for an offshore wind turbine
PublicationThe offshore wind power industry is the branch of electric energy production from renewable sources which is most intensively developed in EU countries. At present, there is a tendency to install larger-power wind turbines at larger distances from the seashore, on relatively deep waters. Consequently, technological solutions for new supporting structures intended for deeper water regions are undergoing rapid development now. Various...
-
The effects of different doses of caffeine on maximal strength and strength‐endurance in women habituated to caffeine
Publication -
Application of the 3D DEM in the modelling of fractures in pre-flawed marble specimens during uniaxial compression
PublicationPrzedstawiono w tym artykule wyniki modelowania pęknięć w cylindrycznych próbkach marmurowych ze wstępnymi nacięciami w czasie jednoosiowego ściskania . Zastosowano metodę elementów dyskretnych (DEM). Zbadano propagację i koalescencję pęknięć w próbkach marmuru z istniejącymi otwartymi nacięciami pod różnymi kątami do poziomu. Wyniki numerycznych symulacji trójwymiarowych (3D) zostały bezpośrednio porównane z badaniami laboratoryjnymi....
-
On the use of uniaxial one-parameter damage laws for estimating fatigue life under multiaxial loading
PublicationThe goal of this paper is to evaluate the capabilities of different one-parameter fatigue laws to estimate crack initiation in notched components under multiaxial loading. Fatigue damage is accounted for through stress-based, strain-based, and energy-based approaches while the cyclic plasticity at the notch-controlled process zone is estimated using linear-elastic simulations. The results show that energy-based formulations established...
-
Dynamic Signal Strength Mapping and Analysis by Means of Mobile Geographic Information System
PublicationBluetooth beacons are becoming increasingly popular for various applications such as marketing or indoor navigation. However, designing a proper beacon installation requires knowledge of the possible sources of interference in the target environment. While theoretically beacon signal strength should decay linearly with log distance, on-site measurements usually reveal that noise from objects such as Wi-Fi networks operating in...
-
Estimation of the Ultimate Strength of FRP Strips-to-Masonry Substrates Bond
PublicationFiber-Reinforced Polymers (FRP) were developed as a new method over the past decades due to their many beneficial mechanical properties, and they are commonly applied to strengthen masonry structures. In this paper, the Artificial Neural Network (ANN), K-fold Cross-Validation (KFCV) technique, Multivariate Adaptive Regression Spline (MARS) method, and M5 Model Tree (M5MT) method were utilized to predict the ultimate strength of...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublicationThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
Synthesis of CoFe2O4 Nanoparticles: The Effect of Ionic Strength, Concentration, and Precursor Type on Morphology and Magnetic Properties
PublicationThe present study highlights the effect of metal precursor types (SO4 2¯, Cl¯, and NO3¯), their concentration, and the influence of ionic strength of reaction environment on the morphology, surface, and magnetic properties of CoFe2O4 particles. The magnetic nanoparticles were obtained by chemical coprecipitation in alkaline medium at increasing metal concentration in the range of 0.0425 mol·dm-3 to 0.17 mol·dm-3 and calcination...
-
Strength analysis of the support structure of the offshore wind turbine
PublicationThe global power demand from renewable sources is growing. One of a very favorable solution which meets severe environmental protection requirements are the offshore wind turbines. The offshore wind energy sector has experienced very fast development over last decade. Offshore wind farms, in comparison with onshore applications, can provide increased efficiency with reduced noise, visual, transportation and installation con-flicts....
-
Influence of Heat Treatment Temperature on Fatigue Toughness in Medium-Carbon High-Strength Steels
PublicationCurrent research has demonstrated that the tempering temperature affects the martensitic transformation of medium-carbon high-strength steels. This temperature plays an important role in the final microstructure, percentage ratios of martensite to ferrite phases and, consequently, in the mechanical properties and the fatigue response. So far, the relationship between the martensitic tempering temperature and the cyclic deformation...
-
A methodology for ultimate strength assessment of ship hull girder accounting for enhanced corrosion degradation modelling
PublicationThe presented work shows a methodology for the ultimate strength assessment of a ship hull, considering enhanced corrosion modelling. The approach is based on the classical Smith method. However, the recent findings regarding the impact of corrosion degradation on ultimate strength are incorporated. To this end, the stress–strain relationships for particular elements composing ship hull cross-section are modified using a specially...
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublicationThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...