Search
Filters
total: 3753
filtered: 3149
displaying 1000 best results Help
Search results for: FRICTION RESISTANCES
-
Analiza i ocena poprawności działania węzła tarcia w aspekcie II zasady termodynamiki
PublicationW artykule przedstawiono autorską metodę sprawdzania poprawności działania węzła tarcia traktowanego jako układ tribologiczny w aspekcie II zasady termo-dynamiki na podstawie analizy i oceny wyników badań laboratoryjnych wykonanych na stanowisku badawczym. Jako stanowisko wykorzystany został zmodyfikowany węzeł tarcia aparatu czterokulowego T-02. Zaprezentowano algorytm, według którego zostały wykonane badania empiryczne. Wykazano,...
-
Cavitation behavior of the SUPERSTON alloy after laser treatment
PublicationResults of laser treatment at cryogenic conditions and its influence on microstructure, microhardness and cavitation resistance of the SUPERSTON alloy are presented in this paper. Obtained results point at possibility of the increase hardness and cavitation resistance of the parts worked in cavitation conditions.
-
Presence and distribution of antibiotic-resistant bacteria in multiphase activated sludge system
PublicationIn total 237 isolates of coliforms (113 strains) and enterococci (124 stains) from influent, mixed liquor in bioreactor and effluent of wastewater treatment plant (WWTP), were isolated on selective media and examined for antibiotic resistance. From 50 to 80% of the coliform strains isolated from the raw and treated sewage were resistant against ceftazidime CAZ, cefuroxim CXM, cefalotin KF and against amoxicillin AML, and only below...
-
WHY SHOULD WE ADOPT NON-USED ATTICS OF MONUMENTAL SACRAL CATHOLIC CHURCHES FOR SECULAR PURPOSES?
PublicationA motive for adapting the desecrated churches to new purposes is a broadly discussed matter, progressively better investigated and defined. Is it advisable to introduce a new, permanent function, complementary to the sacred one in the historical ecclesial buildings? This paper presents the results of the research on benefits of adapting the non-utilized attics of monumental churches still performing their sacred function, located...
-
Enhanced Spectroscopic Insight into Acceptor-Modified Barium Strontium Titanate Thin Films Deposited via the Sol–Gel Method
PublicationIn the present paper, composite thin films of barium strontium titanate (BaxSr1−xTiO3) with an acceptor modifier (magnesium oxide—MgO) were deposited on metal substrates (stainless steel type) using the sol–gel method. The composite thin films feature BaxSr1−xTiO3 ferroelectric solid solution as the matrix and MgO linear dielectric as the reinforcement, with MgO concentrations ranging from 1 to 5 mol%. Following thermal treatment...
-
Te use of acoustic emission for assessment of the oil lubricity in a four-ball tester
Publicationin view of the increased dynamic and temperature load in the compression-ignition engine tribological systems, particular attention is drawn to the problem of such lubrication of the friction nodes that after breaking the boundary layer it could be restored without any wear occurring. therefore, an idea has been devised of introducing to friction nodes, with the lubrication oils, of new substances (operational preparations) modifying...
-
Modeling organic nitrogen conversions in activated sludge bioreactors
PublicationFor biological nutrient removal (BNR) systems designed to maximize nitrogen removal, the effluent total nitrogen (TN) concentration may range from 2.0 to 4.0 g N/m3 with about 25-50% in the form of organic nitrogen (ON). In this study, current approaches to modeling organic N conversions (separate processes vs. constant contents of organic fractions) were compared. A new conceptual model of ON conversions was developed and combined...
-
An investigation of microstructural basis for corrosion behavior of Al-CNT composites fabricated by SPS
PublicationIn this research effect of the addition of multi-wall carbon nanotubes (MWCNTs) as additive powder on microstructure and corrosion behavior of fabricated Al-CNT composites was studied. The aluminum powder and CNTs were mixed with high energy planetary ball-mill. It is observed that by increasing milling time, the uniformity of CNTs on aluminum matrix and consequently corrosion resistance of Al-CNT composite is increased. On the...
-
Hypericum alpestre extract exhibits in vitro and in vivo anticancer properties by regulating the cellular antioxidant system and metabolic pathway of L‐arginine
PublicationConventional treatment methods are not effective enough to fight the rapid increase in cancer cases. The interest is increasing in the investigation of herbal sources for the development of new anticancer therapeutics. This study aims to investigate the antitumor capacity of Hypericum alpestre (H. alpestre) extract in vitro and in vivo, either alone or in combination with the inhibitors of the L‐arginine/polyamine/nitric oxide...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublicationPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Computational complexity and length of recorded data for fluctuation enhanced sensing method in resistive gas sensors
PublicationThis paper considers complexity and accuracy of data processing for gas detection using resistance fluctuation data observed in resistance gas sensors. A few selected methods were considered (Principal Component Analysis – PCA, Support Vector Machine – SVM). Functions like power spectral density or histogram were used to create input data vector for these algorithms from the observed resistance fluctuations. The presented considerations...
-
Tribological model of porous bearings with particular attention given to the lubricant lubricity
PublicationThe friction and wear problems, accompanying all the tribological systems, lead to reduced service life. In order to prevent such situation, it is necessary to maintain fluid friction, which improves durability of all friction nodes in a tribological system. In the paper, the tribological system consists of porous bearings and the model deals with their weakest spots - the oil outflow points in the porous wall. A kinetic model...
-
Evaluation of structural change during fast transformation process of cross-linked NR into liquid NR by light pyrolysis
PublicationThe presence of cross-linked networks in rubber creates a tremendous problem for recycling and reusing of waste rubber. Fast transformation of cross-linked natural rubber (NR) into liquid natural rubber was carried out by light pyrolysis in temperature range from 240 to 300 °C in variable time (in range: 1–30 min). The transformation efficiency was evaluated by measuring the sol fraction and the cross-link density of the gel fraction....
-
Wpływ kierowcy na opór toczenia samochodu
PublicationW pracy omówiono wpływ zachowań kierowcy na opory toczenia pojazdu w ruchu drogowym. Można tu wyróżnić styl jazdy kierowcy oraz jego dbałość o pojazd. Przedstawiono wzrost oporu toczenia w aspekcie dynamicznego przyspieszania oraz szybkiej jazdy na zakręcie. Przeanalizowano także wpływ na opór toczenia takich czynników jak: ciśnienie w ogumieniu obciążenie promieniowe, zbieżność kół jezdnych samochodu oraz zużycie ogumienia.
-
Application of electrochemical impedance spectroscopy to monitoring discharging process of nickel/metal hydride battery.
PublicationThis paper presents the possibility of applying impedance analysis to cell diagnostics. In order to obtain characteristic curves of both electrodes of a NiMH battery simultaneously, a reference electrode was added into the circuit. The authors analysed the cell under three cases, i.e. when its properties are determined only by the state of the positive electrode, only by the state of the negative electrode, or when both electrodes...
-
MANDARIN PEEL AS AN AUSPICIOUS FUNCTIONAL FILLER FOR POLYMER COMPOSITES
PublicationThis work describes the application of mandarin peel (MP) as a waste filler for high-density polyethylene (HDPE) composites. The main goal was to investigate the impact of the filler's essential oils, which include multiple terpenes and terpenoids, on the processing, physicochemical, mechanical, and thermal properties of the composites as a function of different filler content (1 – 10 wt%), as well as its effect on the color and...
-
Advanced Lithium-Ion Battery Model for Power System Performance Analysis
PublicationThe paper describes a novel approach in battery storage system modelling. Different types of lithium-ion batteries exhibit differences in performance due to the battery anode and cathode materials being the determining factors in the storage system performance. Because of this, the influence of model parameters on the model accuracy can be different for different battery types. These models are used in battery management system...
-
Human-associated bacteria and their mobile genetic elements - important minority in wastewater and wastewater impacted ecosystems
PublicationSince human-associated bacteria have been recognized as vectors in two - way gene transmission between the pathogenic and environmental populations, health hazard connected with wastewater discharge requires reevaluation. In this paper the particular attention was given to antimicrobial-resistance of Escherichia coli and enterococci isolated from wastewater and wastewater impacted environments. The obtained results showed that...
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublicationThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...
-
Analysis of the Possibility of Using New Types of Protective Coatings and Abrasion-Resistant Linings under the Operating Conditions of the Spiral Classifier at KGHM Polska Miedź S.A. Ore Concentration Plant
PublicationA study was carried out to select the appropriate coatings for corrosion protection of the spiral classifier working at KGHM Polska Miedź S.A. Ore Concentration Plant. The abrasion resistance of selected protective coatings and wear-resistant linings was investigated using a DT-523 rotary abrasion tester with Taber CS-10 rubber abrasive discs. The average weight loss of the coatings after a cycle of 2000 revolutions was determined....
-
Detailed experimental investigations on frictional pressure drop of R134a during flow boiling in 5 mm diameter channel: The influence of acceleration pressure drop component =Études expérimentales détaillées sur la chute de pression frictionnelle du R134a lors de l'ébullition en écoulement dans un canal de 5 mm de diamètre : influence de la composante d'accélération de la chute de pression
PublicationThis article presents detailed two-phase diabatic pressure drop data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg m−2 s−1. The obtained data are used as a validation of the void fraction literature models, a set of graphs shows comparisons, for a representative set of experimental conditions,...
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublicationIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
Deep slot effect in the squirrel-cage induction motors with scalar (V/F) control
PublicationQualitative characteristics of the electrical drive considerably depend on identification accuracy of math model parameters. In particular, it is depend on detection accuracy of stator active resistance r1 that is used in calculation of flux linkages, rotary speed in sensorless control systems. Paper provides analysis of influence of stator deep slot effect to stator active resistance value
-
Fluctuation-enhanced and conductometric gas sensing with nanocrystalline NiO thin films: A comparison
PublicationNanocrystalline thin films of NiO were prepared by advanced reactive gas deposition, and their responses to formaldehyde, ethanol and methane gases were studied via fluctuation-enhanced and conductometric methods Thin films with thicknesses in the 200–1700-nm range were investigated in as-deposited form and after annealing at 400 and 500 °C. Morphological and structural analyses showed porous deposits with NiO nanocrystals having...
-
Simple Measurement Method for Resistive Sensors Based on ADCs of Microcontrollers
PublicationA new, complete measurement method for resistance measurement of resistive sensors for systems based on microcontrollers equipped with analog-to-digital converters (ADCs) is proposed. The interface circuit consists of only four resistors, including a resistive sensor and a reference resistor, connected directly to the microcontroller pins. It is activated only during measurements, which significantly reduces power consumption....
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublicationThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...
-
IDENTIFICATION OF THE INTERFECE OF LATERAL SLIDE BEARINGS
PublicationIn the paper, the model of slide bearings of motor engine, the metodology of research on this type of bearings and its results are presented measurement standpoint consisting of main elements of Briggs & Stratton 550 serie 10 T 802 model piston motor engine driven by three phase elektric engine is introduced . On the measurement standpoint are measurements were done, needed for specification...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublicationThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
A Simplified Method of Trend Removal to Determine Noise Observed During a Supercapacitor’s Discharging
PublicationIn this paper, new method of trend removal is proposed. This is a simplified method based on Empirical Mode Decomposition (EMD). The method was applied for voltage time series observed during supercapacitor discharging process. It assured the determination of an additive noise component after subtracting the identified trend component. We analyzed voltage time series observed between the terminals of the supercapacitor when discharged...
-
Determination of Earth Pressure and Displacement of the Retaining Structure According to the Eurocode 7-1
PublicationComparative analysis of standard guidelines and findings given in EC7-1 and in Polish Standard PN-83/B-03010. Discussed guidelines concerning active and passive earth pressure as well as at rest pressure state. Wall displacement causing limit states of earth pressure and resistance. Interactive assumptions concerning intermediate earth pressure and resistance values. Conclusions and final remarks.
-
High performance LaNi1-xCoxO3-δ (x = 0.4 to 0.7) infiltrated oxygen electrodes for reversible solid oxide cells
PublicationOxygen electrodes prepared by infiltration of yttria stabilized zirconia backbone with Ce0.8Gd0.2O1.95 barrier layer and LaNi1-xCoxO3-δ (x=0.4 to 0.7) catalyst for application in reversible solid oxide cells have been studied. The effect of temperature and Ni:Co ratio on their phase composition, microstructure and electrochemical properties are discussed. It was shown that oxygen electrodes infiltrated with LaNi0.5Co0.5O3-δ had...
-
Hydrauliczna wiarygodność wyników pomiarów terenowych stosowanych do identyfikacji oporności hydraulicznej przewymiarowanych sieci wodociągowych
PublicationPublikacja zawiera zalecenia metodyczne dotyczące identyfikacji oporności hydraulicznej w przewymiarowanych sieciach wodociągowych na tle spotykanych nieprawidłowości. Krytycznie oceniono wyniki pomiarów terenowych, które zastosowano do tarowania komputerowych modeli przepływów (KMP) pomimo, że nie spełniały kryterium hydraulicznej wiarygodności. Ponadto zaproponowano spadek hydrauliczny jako obiektywny wskaźnik wiarygodności pomiarów,...
-
The quality of sewage sludge stabilized for a long time in reed basins
PublicationThe aim of the work was to determine changes of long-term sewage sludge quality stabilized in reed basins from 7-15 years. The following parameters were evaluated: dry matter and organic matter concentration, nitrogen, phosphorus, and selected heavy metal (Cd, Ni, Pb, Cr, Cu, Zn) fractions. The material for the investigations was collected from 4 reed basin systems (utilisated sewage sludge) located in conventional WWTPs in Denmark...
-
Influence of the grains shape on the mechanical behavior of granular materials
PublicationDiscrete Element Method is a numerical method suitable for modeling geotechnical problems concerning granular media. In most cases simple forms of grains, like discs or spheres, are used. But these shapes are capable of soil behavior modeling up to a certain point only, they cannot reflect all of the features of the medium (large shear resistance and large volumetric change). In order to reflect the complex behavior of the real...
-
Comparative 3D DEM simulations of sand–structure interfaces with similarly shaped clumps versus spheres with contact moments.
PublicationThree-dimensional simulations of a monotonic quasi-static interface behaviour between initially dense cohesionless sand and a rigid wall of different roughness during tests in a parallelly guided direct shear test under constant normal stress are presented. Numerical modelling was carried out by the discrete element method (DEM) using clumps in the form of convex non-symmetric irregularly shaped grains. The clumps had an aspect...
-
Hydrogen effects in duplex stainless steel welded joints - electrochemical studies
PublicationIn this work results on the influence of hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel (DSS) welded joints are described. The results were discussed by taking into account three different areas on the welded joint: weld metal (WM), heat-affected zone (HAZ) and parent metal. The corrosion resistance was qualified with the polarization curves registered in a synthetic sea water. The conclusion is that,...
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublicationTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
Review on Current Status of Echinocandins Use
PublicationFungal infections are rising all over the world every year. There are only five medical compound classes for treatment: triazoles, echinocandins, polyenes, flucytosine and allylamine. Currently, echinocandins are the most important compounds, because of their wide activity spectrum and much lower sides effects that may occur during therapy with other drugs. Echinocandins are secondary metabolites of fungi, which can inhibit the...
-
Dynamics Conscious Approach to Tribometer Design and Tribo-testing
PublicationIn the paper findings are discussed on the issue of dynamic characteristics of a tribometer as a factor influencing the result of the tribological experiment. An advanced approach to tribo-testing is attempted with integrated dynamic analysis of the tribometer and the sliding pair. The fundamental idea is explored of the tribometer being regarded as any machine in which friction is inflicted with all the resulting consequences...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublicationRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
The retrofitting of ships by applying retractable bow hydrofoils: a case study
PublicationIncreasing environmental requirements and a relatively long ship life of 30 years mean more attention is needed to retrofit existing ships. One possibility is using hydrofoils to reduce the ship’s resistance and improve comfort and safety in rough sea conditions. This study investigates the influence of retractable bow hydrofoils on the seakeeping performance and operational conditions of a selected case study vessel (V-shaped...
-
UV-Light-Induced Fluctuation Enhanced Sensing by WO3-Based Gas Sensors
PublicationWO3-based gas sensors were investigated under UV-light irradiation and at different working temperatures with the object of achieving superior sensitivity and selectivity. Resistance fluctuations in the WO3 layer were studied together with dc resistance measurements. The data were taken in synthetic air, ethanol, nitrogen dioxide, and mixtures of these gases. We conclude that UV irradiation can easily be applied to enhance the...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
The influence of screw configuration and screw speed of co-rotating twin screw extruder on the properties of products obtained by thermomechanical reclaiming of ground tire rubber
PublicationThe results of our investigations on the process of continuous thermomechanical reclaiming of ground tire rubber (GTR) carried out using a twin screw extruder are presented.We used a co-rotating twin screw extruder with a special configuration of plasticizing unit, enabling generation of considerable shear forces. The influence of screw configuration and screw speed on breaking of chemical crosslink bonds contained in ground tire...
-
Structural and electronic properties of diamond-composed heterostructures
PublicationDiamond is a promising material for 21st century electronics due to its high thermal and electronic conductivity, biocompatibility, chemical stability, high wear resistance, and possibility of doping. However, the semiconductor properties of diamond, especially free-standing films, have not been fully explored. Nor have their integration with polymers and fragile materials and their applications as electronic components. In this...
-
ENVIRONMENTAL DEGRADATION OF DISSIMILAR AUSTENITIC 316L AND DUPLEX 2205 STAINLESS STEELS WELDED JOINTS
PublicationThe paper describes structure and properties of dissimilar stainless steels welded joints between duplex 2205 and austenitic 316L steels. Investigations were focused on environmentally assisted cracking of welded joints. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement was determined in slow strain rate tests (SSRT) with the strain rate of 2.2 × 10–6 s–1. Chloride-inducted SCC was determined in the...
-
The use of Acoustic Emission to identification damages bearings the main and crank engines about the automatic ignition
PublicationThe article describes the laboratory tests, which make the first stage of the study concerning the use of the AE method to determine the technical state of the slide bearings in engines with self-ignition. The aim of the present tests was to compare the recorded signals in relation to the technical state of the material of the bearing bush and to check the possibility of using the AE method in determining the transition moment...
-
Cavitation Erosion – Phenomenon and Test Rigs
PublicationThe cavitation and cavitation erosion phenomenon have been shortly presented. The main four types of test rigs to investigate the cavitation erosion resistance have been shown. Each type of test design is described and an example of a design is shown. A special attention has been payed to the designs described in the International ASTM Standards: a vibratory design and a cavitating jet cell. There was shown that the design of a...
-
A measurement method for lossy capacitive relative humidity sensors based on a direct sensor-to-microcontroller interface circuit
PublicationA new time-domain measurement method for determining the capacitance and resistance values of lossy relative humidity capacitive sensors is presented. The method is based on a direct sensor-to-microcontroller interface for microcontrollers with internal analog comparators and timers. The interface circuit consists only of four reference resistors (two reference resistors if a microcontroller includes a voltage reference source),...
-
Effects of FSW Tool Plunge Depth on Properties of an Al-Mg-Si Alloy T-Joint: Thermomechanical Modeling and Experimental Evaluation
PublicationOne of the main challenging issues in friction stir welding (FSW) of stiffened structures is maximizing skin and flange mixing. Among the various parameters in FSW that can affect the quality of mixing between skin and flange is tool plunge depth (TPD). In this research, the effects of TPD during FSW of an Al-Mg-Si alloy T-joint are investigated. The computational fluid dynamics (CFD) method can help understand TPD effects on FSW...