Filters
total: 2242
filtered: 1785
displaying 1000 best results Help
Search results for: photosynthesis rates
-
Simultaneous Removal of Al, Cu and Zn Ions from Aqueous Solutions Using Ion and Precipitate Flotation Methods
PublicationThis paper presents the results of investigations concerning the simultaneous removal of Al(III), Cu(II), and Zn(II) from dilute aqueous solutions using ion and precipitate flotation methods. The effects of initial solution pH, surface active substance concentration, and the gas velocity on the flotations’ efficiency and course are studied. Experimental results are discussed in terms of physicochemical aspects related to aqueous...
-
Application of galvanodynamic impedance spectroscopy for studying passive film cracking under mechanical strain
PublicationThe paper reports the results of simultaneous mechanical and electrochemical investigations on austenitic (18/8) stainless steel in a 2 % solution of sulphuric acid. The measurements were performed using Galvanodynamic Electrochemical Impedance Spectroscopy (GDEIS). Electrochemical analysis of mechanical passive layer cracking and repassivation conditions during a tensile test was carried out. Application of this methodology allowed...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublicationThe paper discusses the effect of application of water-Al2O3 nanofluid, as a working fluid, on the efficiency of a flat plate solar collector. The mass concentration of nanoparticles was 0.1%, 0.2% and 0.4%. The tests were conducted for two values of radiation of about 1050 W/m2 and 400 W/m2, and volume flow rates of 60 l/h, 120 l/h and 170 l/h. The efficiency was calculated according to recommendations of the Polish Standard....
-
Vertical vibration reduction and audible sound analysis in surface grinding with electroplated tools
PublicationOne of the first approaches to the development of a grinding process monitoring system based on audible sound sensors is presented in the paper. Electroplated diamond tools (abrasive D64 and D107) were used in a modified single-disc lapping machine configuration for flat grinding of ceramics (Al2O3). The main aim of the machine modification was to reduce the vertical vibration in order to decrease the tool wear and to increase...
-
Corrosion hazards and inhibitor protection in the seawater injection system on the Baltic sea rig
PublicationOil extraction efficiency in LOTOS Petrobaltic Company is increased by means of injection of seawater into an oilfield aquifer, which is implemented on the Baltic Beta rig, operating on the Baltic Sea. Operational experience has shown a significant degree of corrosion aggressiveness in the injected water, which necessitates frequent repairs of the seawater injection installation. Evaluation of the corrosion phenomena is crucial...
-
Wpływ liczby mieszkańców na obliczenia ilości ścieków w projektowaniu kanalizacji sanitarnej
PublicationZmiana sposobu rozliczania zużycia wody, promocja wodooszczędnych technologii oraz uszczelnienie kanałów wyraźnie wpłynęły na ilość odprowadzanych do kanalizacji ścieków. Obecnie stwierdzić można, że opracowania z lat 70-tych XX wieku podają zawyżone wskaźniki odpływu ścieków, skutkiem czego są problemy eksploatacyjne. Bez wątpienia, prawidłowe zaprojektowanie kanalizacji sanitarnej to zadanie trudne, wymagające między innymi prawidłowego...
-
Nitrification, denitrification, and dephosphatation capability of activated sludge during co-treatment of intermediate-age landfill leachates with municipal wastewater
PublicationThis study focuses on the possible use and efficacy of the co-treatment of landfill leachate (intermediate-age) with municipal wastewater. The nitrification, denitrification, and dephosphatation capability of activated sludge acclimated with a mixture of raw municipal wastewater (RWW) with gradually increasing amounts of raw landfill leachate (RLL) (from 0.5 to 5% v/v) were tested. Biochemical tests were conducted simultaneously...
-
Organic matter removal efficiency in treatment wetlands simulation by COD fractions
PublicationThe objective of this paper was to investigate the organic fraction (colloidal, particulate, and dissolved) in sewage treatment in treatment wetland. Performance of TWs was simulated well with a simple first order model k – C* based on monitoring data. In this investigation background or residual concentration (C*) was assumed to be equal concentration of input influent organic matter in particulate (CODp). Calculated reaction...
-
Understanding the kinetics and atmospheric degradation mechanism of chlorotrifluoroethylene (CF2=CFCl) initiated by OH radicals
PublicationThe atmospheric degradation of chlorotrifluoroethylene (CTFE) by OH˙ was investigated using density functional theory (DFT). The potential energy surfaces were also defined in terms of single-point energies derived from the linked cluster CCSD(T) theory. With an energy barrier of −2.62 to −0.99 kcal mol−1 using the M06-2x method, the negative temperature dependence was determined. The OH˙ attack on Cα and Cβ atoms (labeled pathways...
-
Effect of Vascular Lumen Reduction on the Performance and Energy Consumption of an Innovative Implantable LVAD
PublicationThis paper presents the results of a study on the effect of vascular lumen reduction on the performance of an innovative implantable LVAD (left ventricular assist device). It details the pressures in the individual cardiac chambers as a function of device frequency. In addition, mass flow rates and energy consumption of the device are examined, varying with lumen reduction and operating frequency. While the lumen reduction of the...
-
Nitrogen transformations and mass balances in anaerobic/anoxic/aerobic batch experiments with full-scale biomasses from BNR activated sludge systems.
PublicationThe aim of this study was to investigate nitrogen mass balances occurring inside full-scale BNR activated sludge systems, with special attention to colloidal and dissolved organic nitrogen (CON and DON) transformations. For this purpose, laboratory experiments were carried out using process biomass from two large BNR plants in northern Poland. Two parallel batch reactors were operated in a 3-phase (anaerobic/anoxic/aerobic) cycle....
-
Nitrogen transformations and mass balances in anaerobic/anoxic/aerobic batch experiments with full-scale biomasses from BNR activated sludge systems.
PublicationThe aim of this study was to investigate nitrogen mass balances occurring inside full-scale BNR activated sludge systems, with special attention to colloidal and dissolved organic nitrogen (CON and DON) transformations. For this purpose, laboratory experiments were carried out using process biomass from two large BNR plants in northern Poland. Two parallel batch reactors were operated in a 3-phase (anaerobic/anoxic/aerobic) cycle....
-
Disinfection characteristics of an advanced rotational hydrodynamic cavitation reactor in pilot scale
PublicationHydrodynamic cavitation is a promising technique for water disinfection. In the present paper, the disinfection characteristics of an advanced hydrodynamic cavitation reactor (ARHCR) in pilot scale were studied. The effects of various flow rates (1.4–2.6 m3/h) and rotational speeds (2600–4200 rpm) on the removal of Escherichia coli (E. coli) were revealed and analyzed. The variation regularities of the log reduction and reaction...
-
Influence of nitrogen and organic matter fractions on wastewater treatment in treatment wetland
PublicationMunicipal wastewater contains both biodegradable and non-degradable pollutants. Moreover, they are present in dissolved, colloidal and particulate forms. These fractions are characterised by various decomposition rates, hence their bioavailability during microbial respiration. It was confirm that biological degradation rate in terms of COD reduction is influenced by particle size speciation. Therefore, the objective of the study...
-
Localization and Orientation of Xanthophylls in a Lipid Bilayer
PublicationXanthophylls (polar carotenoids) play diverse biological roles, among which are modulation of the physical properties of lipid membranes and protection of biomembranes against oxidative damage. Molecular mechanisms underlying these functions are intimately related to the localization and orientation of xanthophyll molecules in lipid membranes. In the present work, we address the problem of localization and orientation of two xanthophylls...
-
Impact of slow breathing on the blood pressure and subarachnoid space width oscillations in humans
PublicationThe aim of the study was to assess cardiac and respiratory blood pressure (BP) and subarachnoid space (SAS) width oscillations during the resting state for slow and fast breathing and breathing against inspiratory resistance. Experiments were performed on a group of 20 healthy volunteers (8 males and 12 females; age 25.3 ± 7.9 years; BMI = 22.1 ± 3.2 kg/m2). BP and heart rate (HR) were measured using continuous finger-pulse photoplethysmography....
-
Microstructure and corrosion behaviour of carbon steel and ferritic and austenitic stainless steels in NaCl solutions and the effect of p-nitrophenyl phosphate disodium salt
PublicationThe microstructure and corrosion behavior of carbon steel (CSA516) and ferritic (SS410) and austenitic (SS304L) stainless steels were studied and compared. Corrosion tests were carried out in 0.5 M NaCl solutions. Rates of corrosion were monitored based on weight loss, Tafel extrapolation and linear polarization resistance (LPR) methods. Rates of corrosion were ranked following the order: CSA516 >> SS410 > SS304L. The impact of...
-
Experimental research on helical coil biomass boiler with oil as a heating fluid
PublicationThis paper presents an experimental research of helical coil biomass boiler with thermal oil heating agent. Heat exchanger consists of two coaxial helical coils swept by the flue gases. The burner is a single vertical retort connected to the fuel tank (wooden pellets). The boiler is a part of micro-power plant in which the heat from the boiler is exchanged with low-boiling HFE7100 to produce steam for a custom steam turbine. The...
-
CO2 capture through direct-contact condensation in a spray ejector condenser and T- junction separator
PublicationThe design principle underlying the steam condensation and CO2 purification in a gas power plant with a focus on reducing CO2 emissions encompasses the deployment of a spray ejector condenser (SEC) and separator. This innovative system facilitates direct-contact condensation of steam with non-condensable gas (CO2) by inter acting with a spray of subcooled water, seamlessly integrated with a T-junction separator mechanism aimed...
-
Multi-response optimization on the effect of wet and eco-friendly cryogenic turning of D2 steel using Taguchi-based grey relational analysis
PublicationMaterial removal processes, including turning and milling, are still commonly used operations for manufacturing most of mechanical components in modern industry. Apart from the cutting parameters, the cooling method has the great impact on the technological efects and, above all, on the environmental friendliness of production. In this study, multi-response optimization on the efect of wet and cryogenic machining is performed during...
-
Understanding the capacitance of thin composite films based on conducting polymer and carbon nanostructures in aqueous electrolytes
PublicationIn this work electrochemical performance of thin composite films consisted of poly(3,4-ethylenedioxythiophene) (PEDOT), graphene oxide (GOx) and oxidized multiwalled carbon nanotubes (oxMWCNTs) is investigated in various sulphates (Li2SO4, Na2SO4, K2SO4, MgSO4) and acidic (H2SO4) electrolytes. Capacitance values, rate capability and cycling stability achieved for the composite layers are correlated with the electrolytes’ properties...
-
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublicationPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
Quality Evaluation of Speech Transmission via Two-way BPL-PLC Voice Communication System in an Underground Mine
PublicationIn order to design a stable and reliable voice communication system, it is essential to know how many resources are necessary for conveying quality content. These parameters may include objective quality of service (QoS) metrics, such as: available bandwidth, bit error rate (BER), delay, latency as well as subjective quality of experience (QoE) related to user expectations. QoE is expressed as clarity of speech and the ability...
-
The role of biodegradable particulate and colloidal organic compounds in biological nutrient removal activated sludge systems
PublicationThe efficiency of denitrification and enhanced biological phosphorus removal in biological nutrient removal activated sludge systems is strongly dependent on the availability of appropriate carbon sources. Due to high costs of commercial compounds (such as methanol, ethanol, acetic acid, etc.) and acclimation periods (usually) required, the effective use of internal substrates is preferred. The aim of this study was to determine...
-
The effects of different aeration modes on ammonia removal from sludge digester liquors in the nitritation–anammox proces
PublicationThe aim of this study was to determine the impact of continuous and intermittent aeration on the rate of ammonia removal in the combined nitritation–anammox process. This process was run in two parallel sequencing batch reactors (SBRs), with a working volume V = 10 L, treating sludge digester liquors from the Gdansk (Poland) wastewater treatment plant (WWTP). The ammonia oxidizing bacteria were cultivated from activated sludge...
-
Air-cooled photovoltaic roof tile as an example of the BIPVT system – An experimental study on the energy and exergy performance
PublicationThe air-cooled photovoltaic tile is a subject of presented investigations, which focused on improving the overall system efficiency of PV tiles with heat recovery. The operational efficiency of a PV roof tile, together with the construction optimising the air cooling efficiency, were the main points of plans realized at this research stage. The article describes the experimental research consisting of the assessment of electrical,...
-
The resistance of S235JR steel to cavitation erosion
PublicationThe erosion resistance of S235JR steel to flow cavitation was investigated. In order to understand an influence of steel properties and cavitation intensities on the degradation mechanisms, low-carbon S235JR steel was tested in the as-received state and after thermal treatment (annealing) under four different flow velocities. Annealing decreased steel hardness, which made S235JR steel less resistant to cavitation erosion. The performed...
-
Electrochemical investigations on corosivity of de-icing liquids for railway infrastructure
PublicationThe paper presents the results of electrochemical tests of the de-icing fluid for railway infrastructure. DC and AC electrochemical tests were performed to determine the corrosion rates of structural steel, cast iron and aluminium in the newly produced fluid. The results were compared with the corrosion rates of the same materials in the fluid without corrosion inhibitors. The obtained test results indicate a low corrosion risk...
-
Activity and discrimination against women in the labour market in the countries of Baltic Sea Region
PublicationAn increasing participation of women in the labour market seem to be a key to overcome the problems of the EU labour market and to achieve the objectives of Strategy Europe 2020. Therefore, the objective of this paper is to identify differences in the situation of women in the labour market in selected countries such as those in the Baltic Sea region and to attempt to verify the hypothesis of the existence of discrimination against...
-
Optical emission spectroscopy of plasma generated by a waveguide-supplied microwave plasma source operated at 915MHz
PublicationIn this paper we present the results of an optical emission spectroscopic study of an atmospheric pressure microwave (915 MHz) nitrogen and nitrogen with carbon dioxide (1%) plasma at high working gas flow rate. This study was aimed at determining rotational Trot and vibrational Tvib temperatures of N+2 ions and N2, CN molecules. The plasma was generated in a waveguide-supplied cavity-resonant type microwave plasma source. All...
-
The Influence of Water and Mineral Oil on Pressure Losses in Hydraulic Motor
PublicationIn this paper, pressure losses in hydraulic motor supplied with water and mineral oil (two liquids that have significantly different viscosity and lubricating properties) are described and compared. The experimental tests were conducted using a hydraulic satellite motor that is dedicated to working with different liquids, including water. The methodology of measuring the pressure drop in internal channels of this motor is also...
-
Thermal Image Processing for Respiratory Estimation from Cubical Data with Expandable Depth
PublicationAs healthcare costs continue to rise, finding affordable and non-invasive ways to monitor vital signs is increasingly important. One of the key metrics for assessing overall health and identifying potential issues early on is respiratory rate (RR). Most of the existing methods require multiple steps that consist of image and signal processing. This might be difficult to deploy on edge devices that often do not have specialized...
-
The protection and monitoring of a distribution piping network for potable water supply
PublicationPurpose – The purpose of this paper is to implement the corrosion protection method for steel pipes used in a municipal water-pipe network. Results of an inhibitor protection system installed on the system are presented. Inhibitor protection was required due to the high corrosivity of the water collected by a surface intake, which had resulted in a large number of failures and low water quality, due to the presence of corrosion...
-
Wpływ kierunku rozchodzenia się fali detonacyjnej oraz współczynnika asymetrii na rozkład prędkości odkształceń w kotlinie walcowniczej podczas asymetrycznego walcowania pasma Al-Cu. The influences of the direction of explosion wave and asymetrical coefficient at the distribution of strain rate in the roll cap of bimetallic plate Al-Cu of rolling process.
PublicationPrzedstawiono symulacje komputerowe walcowania blach Al-Cu łączonych wybuchowo. Symulacje przeprowadzono dla procesu walcowania w walcarce o średnicy walców D=150 mm z indywidualnym napędem walców roboczych. W ramach badań numerycznych określony został wpływ kierunku rozchodzenia się fali detonacyjnej na rozkład prędkości odkształcenia w kotlinie walcowniczej asymetrycznie walcowanej blachy bimetalowej Al-Cu.
-
Optoelectronic properties of curved carbon systems
PublicationSystematic investigation of optoelectronic properties of curved carbon systems has been performed and the results have been compared with the representatives of flat carbon systems. Moreover, the application of third order dispersion corrected density functional tight binding method (with third order corrections of self-consistent charges) including Becke-Johnson dumping (DFTB3-D3(BJ)) has been validated in order to obtain reliable...
-
A novel concept of enhanced direct-contact condensation of vapour- inert gas mixture in a spray ejector condenser
PublicationAn analytical model of direct steam condensation (DCC) in the novel idea of spray ejector condenser (SEC) in the presence of inert gas has been developed. It is based on continuity, momentum and energy equations for the steam-carbon dioxide mixture and direct contact condensation mechanisms due to heat transfer and concentration. Crucial in the process of DCC is atomisation of the motive fluid in the ejector. The effect of atomised...
-
Acid-aided epoxy-amine curing reaction as reflected in epoxy/Fe3O4 nanocomposites: Chemistry, mechanism, and fracture behavior
PublicationThis work seeks to answer the question whether or not the presence of acid functional groups accelerate epoxyamine curing reaction. Epoxy/Fe3O4 nanocomposite was considered as a case, where discussions are based on chemistry, mechanism behind curing reactions and fracture behavior influenced by acid assistance to crosslinking. Fe3O4 magnetic nanoparticles (MNPs) with nanosilica decorative layer (B-MNP) were synthesized and subsequently...
-
Utilizing Morphological and Physiological Parameters of Lemna minor for Assessing Tetracyclines’ Removal
PublicationAntibiotics with significant environmental toxicity, e.g., tetracyclines (TCs), are often used in large quantities worldwide, with 50–80% of the applied dose ending up in the environment. This study aimed to investigate the effects of exposure to tetracycline hydrochloride (TC) and minocycline hydrochloride (MIN) on L. minor. Our research evaluated the phytotoxicity of the TCs by analyzing plant growth and biomass and evaluating...
-
Rotational state-changing collisions of C2H− and C2N− anions with He under interstellar and cold ion trap conditions: A computational comparison
PublicationWe present an extensive range of quantum calculations for the state-changing rotational dynamics involving two simple molecular anions that are expected to play some role in the evolutionary analysis of chemical networks in the interstellar environments, C2H− (X1Σ+) and C2N− (X3Σ−), but for which inelastic rates are only known for C2H−. The same systems are also of direct interest in modeling selective photo-detachment experiments...
-
Acclimation of denitrifying activated sludge to a single vs. complex external carbon source during a start-up of sequencing batch reactors treating ammonium-rich anaerobic sludge digester liquors
PublicationIn this study, denitrification of ammonium- reach anaerobic sludge digester liquor was investigated during start-up periods of two laboratory- scale ‘‘fill-and-draw’’ reactors. One reactor was fed with a single carbon source (ethanol), whereas the other reactor was fed with a complex carbon source (fusel oil). During two acclimation experiments, the structure of microbial community involved in denitrification was analyzed using...
-
Investigating Fuel Injection Strategies to Enhance Ship Energy Efficiency in Wave Conditions
PublicationThe prediction of fuel consumption and resulting transportation costs is a crucial stage in ship design, particularly for conditions involving motion in waves. This study investigates the real-time fuel consumption of a container ship when sailing in waves. The overall ship performance is evaluated using a novel non-linear coupled hull-engine-propeller interaction model. A series of towing tank experiments for hull resistance in...
-
Mechanism of reaction of RNA-dependent RNA polymerase from SARS-CoV-2
PublicationWe combine molecular dynamics, statistical mechanics, and hybrid quantum mechanics/molecular mechanics simulations to describe mechanistically the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) RNA-dependent RNA polymerase (RdRp). Our study analyzes the binding mode of both natural triphosphate substrates as well as remdesivir triphosphate (the active form of drug), which is bound preferentially over ATP by RdRp while...
-
Rheology of Variable Viscosity‐Based Mixed Convective Inclined Magnetized Cross Nanofluid with Varying Thermal Conductivity
PublicationCross nanofluid possesses an extraordinary quality among the various fluidic models to explore the key characteristics of flowing fluid during very low and very high shear rates and its viscosity models depend upon shear rate. The current study establishes the numerical treatment regarding variable viscosity‐based mixed convective inclined magnetized Cross nanofluid with var‐ ying thermal conductivities over the moving permeable...
-
Methods of Determining Pressure Drop in Internal Channels of a Hydraulic Motor
PublicationIn this paper, new methods for determining the pressure drop in internal channels of a hydraulic motor are proposed and described. Mathematical models of pressure losses in internal channels have also been described. Experimental tests of the satellite motor were carried out according to one of the proposed methods. The tests were carried out for two liquids, i.e., water and mineral oil. Experimental studies have shown that at...
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublicationEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
Share of the wage factor in national income – selected aspects
PublicationThe aim of this study is to examine changes in the share of the wage factor in national income, in selected EU countries against labour productivity and investment rates reflecting changes in capital-labour relations, indicated by researchers as determinants of change of the share of the wage factor in national income. The scope of the study includes a review of literature devoted to the issue of wage factor share in national income...
-
The selective salinity and hydrazine parameters for the start-up of non-anammox-specific biomass SBR
PublicationThe presence of ammonium (NH 4+ ) in wastewater above the permissible limits leads to undesirable ecological impact and public health concerns. In this study, the anaerobic ammonium oxidizing (anammox) bacteria-mediated nitrogen removal was investigated using a sequential batch reactor (SBR). Effects of different salinity levels were evaluated on the bacterial activity at: mild (below 0.2 g NaCl/L), elevated (18.2 g NaCl/L) and...
-
Effect of Surface Treatment of Halloysite Nanotubes (HNTs) on the Kinetics of Epoxy Resin Cure with Amines
PublicationThe epoxy/clay nanocomposites have been extensively considered over years because of their low cost and excellent performance. Halloysite nanotubes (HNTs) are unique 1D natural nanofillers with a hollow tubular shape and high aspect ratio. To tackle poor dispersion of the pristine halloysite (P-HNT) in the epoxy matrix, alkali surface-treated HNT (A-HNT) and epoxy silane functionalized HNT (F-HNT) were developed and cured with...
-
Cure Index demonstrates curing of epoxy composites containing silica nanoparticles of variable morphology and porosity
PublicationAn image was taken by Cure Index on curability of epoxy with silica nanoparticles having variable morphology and porosity. Three kinds of silica nanoparticles with non-porous curved-rod, non-porous spherical, and mesoporous spherical microstructures were synthesized and characterized by Fourier-transform infrared spectroscopy, scanning electron microscopy (SEM) and Brunauer–Emmett–Teller analyses. Epoxy nanocomposites containing...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublicationThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...