Search
displaying 1000 best results Help
Search results for: GLUED CONNECTIONS
-
Analysis of balancing of four stroke V6 engines
PublicationAnalysis of balance of V6 engines with a common-pin crankshaft depending on a cylinder bank angle and the crank radius to connecting rod length ratios , based on the relations derived, is presented in the paper. The bank angles providing the lowest moment of inertia forces in reciprocating motion, for selected values, were determined. The position of the plane of the main counterweights in order to maximum balance of the moment...
-
Spectral reflectance modeling of ZnO layers made with Atomic Layer Deposition for application in optical fiber Fabry-Perot interferometric sensors
PublicationSuitability of zinc oxide (ZnO) layers grown using Atomic Layer Deposition for operation in optical-fiber extrinsic Fabry-Perot sensors is investigated using a numerical model. Reflectance spectra obtained using the developed model indicate that the application of these layers in optical-fiber extrinsic Fabry-Perot sensors is difficult as it may require a source whose spectrum width is about 300 nm. A series of ZnO layers grown...
-
Reconstruction Methods for 3D Underwater Objects Using Point Cloud Data
PublicationExisting methods for visualizing underwater objects in three dimensions are usually based on displaying the imaged objects either as unorganised point sets or in the form of edges connecting the points in a trivial way. To allow the researcher to recognise more details and characteristic features of an investigated object, the visualization quality may be improved by transforming the unordered point clouds into higher order structures....
-
Pareto Ranking Bisection Algorithm for Expedited Multi-Objective Optimization of Antenna Structures
PublicationThe purpose of this letter is introduction of a novel methodology for expedited multi-objective design of antenna structures. The key component of the presented approach is fast identification of the initial representation of the Pareto front (i.e., a set of design representing the best possible trade-offs between conflicting objectives) using a Pareto-ranking bisection algorithm. The algorithm finds a discrete set of Pareto-optimal...
-
A New Coupler Concept for Contactless High-Speed Data Transmission Monitoring
PublicationThis paper presents a new concept of a couplerthat can be applied to high-speed data transmission contactlessmeasurements. The proposed approach is dedicated for differentialsignal transmission monitoring in microstrip coupled lineson printed circuit boards (PCBs). The coupler, produced on aseparate PCB, is overlayed on the transmission line with thedifferential signal and delivers decoupled differential signal tothe main measurement...
-
Fiber optic displacement sensor with signal analysis in spectral domain
PublicationIn this paper, a study of a low-coherence fiber optic displacement sensor is presented. The sensor consisted of a broadband source whose central wavelength was either at 1310 nm or 1550 nm, a sensing Fabry-Pérot interferometer operating in reflective mode and an optical spectrum analyzer acting as the detection setup. All these components were connected by a single-mode fiber coupler. Metrological parameters of the sensor were...
-
Role of public space in designing complex urban structures
PublicationThe aim of this article is to present the main assumptions about design studios as held in the Faculty of Architecture at Gdańsk University of Technology (FA-GUT), Gdańsk, Poland, adapted to the development of key competencies in the urban planning of complex urban structures. One of these competencies is the design of public spaces. The main goal of the studios was to deliver knowledge of the role of public spaces in the design...
-
Analytical design method for widening the intertrack space
PublicationThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Arching of railway turnouts by analytical design method
PublicationThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Experimental study of the impact of notches and holes made in the front edge of adherends on the properties of static and fatigue strength of adhesive joints
PublicationThe paper presents the results of experimental studies aimed at determining the effect of holes and notches at the front edge of adherends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets joined with Araldite 2014-2 epoxy adhesive were tested. Comparative tests of static strength in the shear test as well as high-cycle fatigue strength tests were carried out. Joints with three holes with a diameter...
-
Józef Kotus dr hab. inż.
People -
Evaluation of RTKLIB's Positioning Accuracy Using low-cost GNSS Receiver and ASG-EUPOS
PublicationThe paper focuses on a comparison of different positioning methods provided by free and open source software (FOSS) package called RTKLIB. The RTKLIB supports real‐time and post‐processed positioning. The most important modes of operation tested by the authors are Kinematic, Static, Fixed and Precise Point Positioning (PPP). The data for evaluation were obtained from low‐cost Global Navigation Satellite System (GNSS) receiver....
-
Systematic approach to binary classification of images in video streams using shifting time windows
Publicationin the paper, after pointing out of realistic recordings and classifications of their frames, we propose a new shifting time window approach for improving binary classifications. We consider image classification in tewo steps. in the first one the well known binary classification algorithms are used for each image separately. In the second step the results of the previous step mare analysed in relatively short sequences of consecutive...
-
Dynamic Data Management Among Multiple Databases for Optimization of Parallel Computations in Heterogeneous HPC Systems
PublicationRapid development of diverse computer architectures and hardware accelerators caused that designing parallel systems faces new problems resulting from their heterogeneity. Our implementation of a parallel system called KernelHive allows to efficiently run applications in a heterogeneous environment consisting of multiple collections of nodes with different types of computing devices. The execution engine of the system is open for...
-
Evaluating Asymmetric N-Grams as Spell-Checking Mechanism
PublicationTypical approaches to string comparing marks two strings as either different or equal without taking into account any similarity measures. Being able to judge similarity is however required for spelling error corrections, as we want to find the best match for a given word. In this paper we present a bi2quadro-grams method for spelling errors correction. The method proposed uses different n-grams dimension for the source (checked)...
-
Kolekcja muzyczna Kazimierza Czekotowskiego (1901-1972) w zbiorach Biblioteki Głównej Akademii Muzycznej im. Stanisława Moniuszki w Gdańsku
PublicationThe Main Library of Stanisław Moniuszko Academy of Music in Gdansk gathers and stores many collections submitted by different people, especially by the pedagogues of the Academy. One of them is a collection of notes used in artistic work and maybe in vocal teaching by the outstanding Polish singer Kazimierz Czekotowski. The article describes the contents of the collection, particularly the items concerning composers and publishers....
-
Methodology for the Correction of the Spatial Orientation Angles of the Unmanned Aerial Vehicle Using Real Time GNSS, a Shoreline Image and an Electronic Navigational Chart
PublicationUndoubtedly, Low-Altitude Unmanned Aerial Vehicles (UAVs) are becoming more common in marine applications. Equipped with a Global Navigation Satellite System (GNSS) Real-Time Kinematic (RTK) receiver for highly accurate positioning, they perform camera and Light Detection and Ranging (LiDAR) measurements. Unfortunately, these measurements may still be subject to large errors-mainly due to the inaccuracy of measurement of the optical...
-
Elective design I: Waterfront Areas in a Changing Climate – Solutions for Gdańsk
e-Learning CoursesElective design I:Waterfront Areas in a Changing Climate – Solutions for Gdańsk for MSc in Arch. Seminars & assignments: 30 hTeacher: Lucyna Nyka, Jakub Szczepański, Justyna Borucka + assist. teacher from Gdańsk Tech Waterfront Areas in a Changing Climate – Solutions for Gdańsk – This course explores challenges, conflicts and concepts in waterfront areas, their connection to architectural and urban design in the time of...
-
Development of Intelligent Control for Annealing Unit to Ensure the Minimization of Retroactive Effects on the Supply Network
PublicationResearch conducted by our team focused on the development of a complete annealing unit, using modern technologies and components, such as a programmable logic controller, an industrial computer and microcontrollers, ensuring an intelligent way to control power semiconductor elements (SSR relays), with regard to minimizing retroactive effects on the supply network. This modern configuration offers a number of new possibilities of...
-
Share of the wage factor in national income – selected aspects
PublicationThe aim of this study is to examine changes in the share of the wage factor in national income, in selected EU countries against labour productivity and investment rates reflecting changes in capital-labour relations, indicated by researchers as determinants of change of the share of the wage factor in national income. The scope of the study includes a review of literature devoted to the issue of wage factor share in national income...
-
On local buckling of cold-formed channel members
PublicationThe paper deals with local buckling of the compressed flanges of cold-formed thin-walled channel beams subjected to pure bending or axially compressed columns. Arbitrarily shaped flanges of open cross-sections and the web-flange interactions are taken into account. Buckling deformation of a beam flange is described by displacement related to torsion of the flange about the line of its connection with the web. Total potential energy...
-
A Wideband Rotary-Joint-Free H-Plane Horn Antenna With 360° Steerable Radiation Pattern Using Gap Waveguide Technology
PublicationConsidering the limitations of electronically steerable antennas such as limited steering span, gain degradation for large steering angles, complexity, and cost, this article is focused on the design of a simple mechanically steerable H-plane horn antenna. It is shown that since there is no need for an electrical connection between the top and bottom sections of a gap waveguide (GWG), if a sectoral horn is properly designed and realized...
-
High catalytic performance of laccase wired to naphthylated multiwall carbon nanotubes
PublicationThe direct electrical connection of laccase on the electrode surface is a key feature in the design of efficient and stable biocathodes. However, laccases can perform a direct electron transfer only when they are in the preferable orientation toward the electrode. Here we report the investigation of the orientation of Laccase from Amano on multi-walled carbon nanotube surface modified with naphthalene group. Naphthylated multi...
-
Cellular network quality evaluation at a university campus on the eve of 5G
PublicationThanks to the availability of mobile devices and the spread of broadband access around the world, the number of network users continues to grow. This has raised user awareness when it comes to the quality of content they consume. Many service providers and operators focus on monitoring QoN (Quality of Network) and QoS (Quality of Service) parameters, particularly those influenced by bandwidth and latency. However, for most end-users,...
-
Three-dimensional characterization of porosity in iron ore pellets: A comprehensive study
PublicationThis paper presents a comprehensive study on the production and reduction of high-quality iron ore pellets characterized by a basicity index nearing 0.5 and diameters ranging from 1 to 2 cm. The reduction process was carried out in a hydrogen atmosphere at temperatures spanning 800–1000 ◦ C and a pressure of 8 bar. Initial f indings revealed substantial variations in pellet density and compressive strength, attributed to their...
-
Video traffic data - Interchange Skawina (A4-44), Poland
Open Research DataThe data includes video traffic data registered with 5 video cameras at entry and exit lanes of the Skawina interchange within A4 motorway in Poland (interchange of motorway A4 and national road 44), located in the Krakow Agglomeration. The data covers the one day: 31.08.2017 (motorway A4).
-
Video traffic data - Interchange Krakow Poludnie (A4-7), Poland
Open Research DataThe data includes video traffic data registered with 5 video cameras at entry and exit lanes of the Krakow Poludnie interchange within A4 motorway in Poland (interchange of motorway A4 and national road 7), located in the Krakow Agglomeration. The data covers the one day: 29.08.2017 (motorway A4).
-
Experimental investigations on heat transfer enhancement in shell coil heat exchanger with VARIABLE Baffles GEOMETRY
PublicationThe paper presents the possibility of using passive intensification of heat transfer in the form of baffles to increase the energy efficiency of the shell and coil heat exchanger. The experiment was carried out by using a modular coil heat exchanger in the form of an electric heater. Water was used as a working fluid with constant thermal-flow parameters at the inlet of the module. It should be noted that experiments were made...
-
Modele numeryczne uwzględniające tarczową pracę pokrycia dachowego z blach trapezowych
PublicationW artykule porównano wybrane sposoby uwzględniania w modelowaniu numerycznym tarczowej pracy pokrycia dachowego z blachy trapezowej, możliwe do zrealizowania w programie Autodesk Robot Structural Analysis Professional 2015, w celu oceny słuszności stosowania ich do obliczeń konstrukcji nośnej współpracującej z poszyciem z blachy trapezowej. Analizy przeprowadzono dla pojedynczej przepony. Za pomocą powłokowych elementów skończonych...
-
Advanced sensitivity analysis of the impact of the temporal distribution and intensity of rainfall on hydrograph parameters in urban catchments
PublicationKnowledge of the variability of the hydrograph of outflow from urban catchments is highly important for measurements and evaluation of the operation of sewer networks. Currently, hydrodynamic models are most frequently used for hydrograph modeling. Since a large number of their parameters have to be identified, there may be problems at the calibration stage. Hence, sensitivity analysis is used to limit the number of parameters....
-
Experiencing historic waterways and water landscapes of the Vistula River Delta
PublicationThe paper gives insights into the characteristics of Vistula River Delta water landscapes, referring to the process of creating land out of water by Polish, Dutch and German settlers. Based on this, the paper presents an integrated strategy formed upon studies in cultural geography and aesthetics, and focused on enhancing the unique characteristics of the region and its rediscovery by tourism. The long process of constructing Vistula...
-
Development of Intelligent Road Signs with V2X Interface for Adaptive Traffic Controlling
PublicationThe objective of this paper is to present a practical project of intelligent road signs, under which a series of new products for the regulation of traffic is being created. The engineering part of the project, described in this paper, was preceded by a series of experimental studies, the results of which were described in another paper accepted for publication at the MTS-ITS conference 2019, entitled "Comparative study on the effectiveness...
-
Possibilities for Developing Electromobility by Using Autonomously Powered Trolleybuses Based on the Example of Gdynia
PublicationTrolleybus transport refers to contemporary challenges related to a reduction in emissions of greenhouse gases and CO2 into the atmosphere formulated by international institutions, such as the United Nations, the Organisation for Security and Co-operation in Europe, or the European Union. Departure from fossil fuels in urban transport is one of the key challenges for the coming years. Trolleybuses are an important tool in this...
-
Educating planners in Europe: A review of 21st century study programmes
PublicationEducation for urban, regional and spatial planning has become a regular subject throughout most European nations; this can be attributed in part to European policies promoting planning and spatially balanced development, but also to the recognition that planning can support sustainability. Nevertheless, there is lingering and justifiable concern about the status, profile and recognition of planning as a profession in its own right...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublicationThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
On-line ranking of split graphs
PublicationA vertex ranking of a graph G is an assignment of positive integers (colors) to the vertices of G such that each path connecting two vertices of the same color contains a vertex of a higher color. Our main goal is to find a vertex ranking using as few colors as possible. Considering on-line algorithms for vertex ranking of split graphs, we prove that the worst case ratio of the number of colors used by any on-line ranking algorithm...
-
THE INTERACTION BETWEEN STEEL COLUMN CHORD AND CLOSELY SPACED REINFORCEMENT.
PublicationNowadays, more often than before, civil engineering designers are willing to use steel build-up members composed of single or doubled cold-formed chords interconnected using different mechanical connectors. This paper subject is an analysis of cooperation of a closely spaced built-up cold-formed chord interconnected with series of bolts that are located along the length of the member in a specific spacing. This distance along the...
-
Decomposition of Acoustic and Entropy Modes in a Non-Isothermal Gas Affected by a Mass Force
PublicationDiagnostics and decomposition of atmospheric disturbances in a planar flow are considered in this work. The study examines a situation in which the stationary equilibrium temperature of a gas may depend on the vertical coordinate due to external forces. The relations connecting perturbations are analytically established. These perturbations specify acoustic and entropy modes in an arbitrary stratified gas affected by a constant...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublicationThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
The analysis of the determination of points positions using photogrammetric methods
PublicationThis article was created as a result of research conducted within the master thesis. The purpose of the research was to analyze the accuracy of determining the actual position of the photographed points according to the calculated parameters. The accuracy of photos alignment was determined as parameters, which determine their external and internal orientation. In order to determine the location of the determined points, it was...
-
Estimation of the Maximum Permissible PV Power to be Connected to the MV Grid
PublicationIn recent decades, a significant increase in the share of renewable energy sources in power grids at various voltage levels has been observed. A number of articles have been published highlighting emerging problems in low-voltage grids with a large share of prosumers and in medium- and high-voltage grids to which photovoltaic (PV) plants are connected. The article analyzes the medium-voltage grid in terms of the possibility of...
-
Strony WWW bibliotek jako element promocji i narzędzie komunikacji z użytkownikiem
PublicationW artykule przedstawiono zasady tworzenia stron WWW bibliotek, ze szczególnym uwzględnieniem bibliotek kościelnych. Zwrócono uwagę na elementy interfejsu i narzędzia służące informacji o zbiorach i usługach, a także promocji działalności biblioteki. Omówiono narzędzia z obszaru Web 2.0, służące komunikacji z użytkownikami w przestrzeni wirtualnej w czasie rzeczywistym (takie jak komunikatory, czaty, formularze zapytań) na przykładzie...
-
Modelowanie i symulacja ruchu pojazdu zabytkowego podczas hamowania
PublicationOpracowano model samochodu zabytkowego z wykorzystaniem metody masa-sprężyna, służącego do symulacji procesu hamowania pojazdu zabytkowego z możliwością pomiaru drogi hamowania. Konfiguracja sieci połączeń między punktami mas elementów zawieszenia oraz opony okazuje się mieć bardzo duży wpływ na zachowanie symulowanego samochodu podczas hamowania. Poprawność symulacji sprawdzono porównując wyniki uzyskane z symulacji oraz z pomiarów...
-
Predykcyjne sterowanie równoległym filtrem aktywnym ze sprzężeniem od prądu zasilającego
PublicationArtykuł przedstawia nowatorską strategię predykcyjnego sterowania równoległym energetycznym filtrem aktywnym (EFA). Proponowane sterowanie zawiera sprzężenie zwrotne od prądu zasilającego i wiąże zalety sterowania w układzie otwartym oraz zamkniętym – szybkość reakcji na zmianę prądu odbioru i bardzo wysoką skuteczność kompensacji. Wysoka jakość prądu kompensacyjnego wynika również z zastosowania w sterowaniu algorytmów predykcyjnych,...
-
Incremental construction of Minimal Tree Automata [online]
PublicationWe describe an algorithm that allows the incremental addition or removal of unranked ordered trees to minimal frontier-to-root deterministic tree automaton (DTA). The algorithm takes a tree t and a minimal DTA A as input; it outputs a minimal DTA A' which accepts the language L(A) accepted by A incremented (or decremented) with the tree t. The algorithm can be used to efficiently maintain dictionaries which store large collections...
-
The experience of movement in the built form and space: A framework for movement evaluation in architecture
Publication“Movement in architecture” is an organized system of various types of movements stimulated by specific architectural elements. This research was conducted through a qualitative-analytical method and empirical and bibliographical research methods with the aim to categorize different types of movements based on the explorer and observer relationships with the built space and form. So far, most of the related studies have focused...
-
A compartment model of alveolar–capillary oxygen diffusion with ventilation–perfusion gradient and dynamics of air transport through the respiratory tract
PublicationThis paper presents a model of alveolar–capillary oxygen diffusion with dynamics of air transport through the respiratory tract. For this purpose electrical model representing the respiratory tract mechanics and differentia equations representing oxygen membrane diffusion are combined. Relevant thermodynamic relations describing the mass of oxygen transported into the human body are proposed as the connection between these models,...
-
Hydraulic potential of the Lower Vistula (Poland)
PublicationThe Vistula is the largest river in Poland. Lower Vistula (part of the river discussed in this paper) is almost four hundred kilometers long river section extending from the tributary Narew to the outflow to the Baltic Sea. In the 17th century the Vistula was the most navigable river in Europe. After partitioning of Poland the Vistula lost its significance. Now the Lower Vistula should provide a navigation connection to the Europe...
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plants. Part B: Prosumer and Distributed Power Industry
PublicationAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. A new modification of a gas turbine cycle with the combustion chamber at the turbine outlet has been described in the paper. A special air by-pass system of the combustor was applied, and in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with an effective heat exchanger could...
-
Analysis of an Energy Management System of a Small Plant Connected to the Rural Power System
PublicationThis paper presents the analysis of an energy management system (EMS) implemented to fulfill the requirements of a microgrid (MG) power supply owned by a small industrial company and connected to the rural power system. The main goal of this system is to ensure connection with the existing rural power system in terms of energy exchange, as well as to perform islanding mode operation of the microgrid based on the energy demand of...