Filters
total: 2227
-
Catalog
displaying 1000 best results Help
Search results for: STANDARDS CONFORMANCE
-
Selected problems of experimental investigation of dynamically loaded journal bearings
PublicationIn the paper some problems concerning relations between external bearing loadings and critical lining stresses are described for test stand with rotating load vector. According to the standard ISO 7905/1 this type of test stand, for dynamically loaded slide bearing, is recommended as a basic research unit for material testing in a complete bearing unit. The lining stress calculation results occurred being dependent on applied calculation...
-
Intelligent turbogenerator controller based on artifical neural network
PublicationThe paper presents a desing of an intelligent controller based on neural network (ICNN). The ICNN ensures at the same time two fundamental functions : the maintaining of generator voltage at the desired value and the damping of the electromechanical oscillations. Its performance is evaluted on a single machine infinite bus power system through computer simulations. The dynamic and transient operation of the proposed controller...
-
EXHAUST TEMPERATURE MEASUREMENTS OF THE MARINE TURBOCHARGED DIESEL ENGINES IN OPERATION
PublicationThe article presents the selected metrology issues concerning the exhaust temperature of the turbocharged marine engines during operation. The special concern has been paid on existing disturbances as well as thermodynamical interpretation of the recorded measurement signal. A diagnostic informativeness of the standard exhaust temperature’s measurements has worked out while the engine runs in steady states has been also considered...
-
Note on the variance of the sum of gaussian functonals
PublicationDowodzi się oszacowania wariancji sum funkcjonałów losowych, konstruowanych dla zależnego ciągu gaussowskiego.Let (Xi; i = 1; 2; : : :) be a Gaussian sequence with Xi 2 N(0; 1) for each i and suppose its correlation matrix R = (ij)i;j1 is the matrix of some linear operator R : l2 ! l2. Then for fi 2 L 2(), i = 1; 2; : : : ; where is the standard normal distribution, we estimate the variation of the sum of the Gaussian functionals...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublicationThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Wideband Model Order Reduction for Macromodels in Finite Element Method
PublicationAbstract: This paper presents a novel algorithm for accelerating 3D Finite Element Method simulations by introducing macromodels created in local model order reduction in the selected subdomains of the computational domain. It generates the projection basis for a compact system of equations associated with a separate subdomain. Due to non-linear frequency dependency in the Right Hand Side (RHS), the standard reduction methods do...
-
Effect of mesh deformation on the accuracy of 3D FEM electromagnetic analysis
PublicationIn this paper, the accuracy of 3D FEM electromagnetic simulations in parametric analysis using mesh deformation techniques is discussed. Mesh deformation techniques allow one to preserve the mesh topology while the geometry is changed. It is shown that the application of mesh deformation can provide accurate simulation results even for very large deformations. On the other hand, it is also shown that the technique has to be used...
-
Podstawy definiowania procesów IT
PublicationNadmiar wdrożeń ISO9000, które na przełomie XX i XXI wieku były bardzo modne, spowodował u szefów polskich firm przesyt i alergię na słowo „ISO”. Tymczasem jest to skarbnica wiedzy zbieranej przez lata i uporządkowanej w numerowany standard. Znajdziemy tam gotowe odpowiedzi na większość nurtujących organizację pytań. Dla firm wytwarzających oprogramowanie lub świadczących usługi IT swego rodzaju biblią powinna być norma ISO/IEC...
-
Intergranular Corrosion Detection Using Electromagnetic Transducers for Ultrasonic Testing
PublicationThe aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after...
-
Instalacje elektryczne niskiego napięcia w standardzie europejskim
PublicationArtykuł przedstawia problemy prawne, techniczne, ekonomiczne w dziedzinie instalacji elektrycznych związane z przystąpieniem Polski do Unii Europejskiej, m.in. zmianę statusu norm, podwyższenie standardów wykonania instalacji, problem odpowiedzialności zawodowej. Objaśnia kwestię znormalizowanych napięć niskich, nowych problemów instalacyjnych oraz instalacji w budynkach inteligentnych.
-
Multidimensional legacy aspects of modernizing web based systems
PublicationPublikacja porusza zagadnienia technik modernizacji tzw. legacy systems mających zastosowanie w cyklach życia oprogramowania. Przedmiotem dyskusji jest także studium przypadku Endoscopy Recommender System. Ponadto rozważany jest wpłw zmian wymagań, platform, standardów oraz strategii rozwoju oprogramowania na status legacy aplikacji webowych.
-
Zarzadzanie ryzykiem jako wymiar strategicznego i przedsiębiorczego podejścia do zarządzania małym i srednim przedsiębiorstwem
PublicationJedną z wielu przyczyn niepowodzenia ekonomicznego małych i średnich przedsiębiorstw jest niezrozumienie lub niewłaściwe rozumienie kwestii zarządzania ryzykiem. Ryzyko w wielu wymiarach sprzężone jest z procesem przedsiębiorczym. Zarządzanie nim wymaga dostrzegania okazji, umiejętności wykorzystywania zagrożeń jako szans oraz dynamicznej odpowiedzi na zmiany w otoczeniu i w samej organizacji. Sposób podej- ścia do zarządzania...
-
Zarządzanie programami badawczymi z uwzględnieniem filozofii nauki
PublicationZarządzanie projektami i programami badawczymi powinno być realizowane z zastosowaniem specyficznych metod zarządzania ze względu na specyfikę badań naukowych. W tym rozdziale zaprezentowano wyniki analiz mających na celu lepsze zrozumienie roli zarządzania programem badawczym z następujących perspektyw: analizy rzeczywistości projektów badawczych, zarządzania projektem i programem oraz filozofii nauki. Praktycznym zastosowaniem...
-
Cele, koncepcja i założenia Krajowego Systemu Zarządzania Ruchem
PublicationW pracy przedstawiono historię prac zmierzających do opracowania jednolitego standardu FRAME. Opisano założenia i cele Krajowego Systemu Zarządzania Ruchem. Przedstawiono 17 modułów wdrożeniowych, które będą wdrażane na drogach sieci TEN-T, sieci dróg krajowych nie należących do tej sieci i na nowo - budowanych odcinkach dróg, w zakresie kontraktów budowlanych. W artykule przedstawiono obszary funkcjonalne KSZR i bazy danych, które...
-
QoS w lokalnych sieciach bezprzewodowych
PublicationZaprezentowano dwa najpopularniejsze obecnie rozwiązania lokalnych sieci bezprzewodowych (Wireless LAN - WLAN). Zarówno sieci standardu IEEE 802.11, jak i ETSI HIPERLAN/2, są postrzegane jako istotne elementy systemów łączności bezprzewodowej czwartej generacji (4G). Ze względu na ograniczoną szerokość pasma radiowego, w sieciach tych niebagatelną rolę zaczynają odgrywać mechanizmy dopasowujące jakość obsługi (QoS) do wymagań aplikacji...
-
QoS w lokalnych sieciach bezprzewodowych.
PublicationZaprezentowano dwa najpopularniejsze obecnie rozwiązania lokalnych sieci bezprzewodowych (Wireless LAN - WLAN). Zarówno sieci standardu IEEE 802.11 jak i ETSI HIPERLAN/2, są postrzegane jako istotne elementy systemów łączności bezprzewodowej czwartej generacji (4G). Ze względu na ograniczoną szerokość pasma radiowego, w sieciach tych niebagatelną rolę zaczynają odgrywać mechanizmy dopasowujące jakość obsługi (QoS) do wymagań aplikacji...
-
Zastosowanie magistrali testującej IEEE 1149.6 do diagnostyki układów cyfrowych sprzężonych pojemnościowo
PublicationPrzedstawiono magistralę ułatwionego testowania standardu IEEE 1149.6 przeznaczoną do diagnostyki złożonych układów cyfrowych sprzężonych pojemnościowo. Zaprezentowano metody transmisji sygnałów cyfrowych o b. wysokich częstotliwościach, a następnie przedstawiono rozwiązania kluczowych elementów magistrali: komórkę brzegowego rejestru wyjściowego z nadajnikiem sygnałów testowych oraz detektor sygnałów różnicowych o sprzężeniu pojemnościowym....
-
The potential of Web-GIS and geovisual analytics in the context of marine cadastre
PublicationThe importance of the marine environment to human existence makes it imperative that information models represent the multidimensional nature of reality as closely as possible in order to facilitate good governance. Information regarding jurisdiction, as well as the effects of formal law and community interests on the marine environment (e.g. nature and spatial extents as well as rights, responsibilities, restrictions etc.) would...
-
Traffic-induced vibrations. The impact on buildings and people
PublicationTraffic-induced vibrations have recently been of major concern to engineers as one of the aspects of so called physical environmental pollution. The interest is related to the observations of serious negative effects of such kind of vibrations on buildings and their inhabitants. Traffic-induced vibrations may cause plaster cracks, structural damage and even failure and collapse of the structure. They may also be the reason of serious...
-
A Comparison of STI Measured by Direct and Indirect Methods for Interiors Coupled with Sound Reinforcement Systems
PublicationThis paper presents a comparison of STI (Speech Transmission Index) coefficient measurement results carried out by direct and indirect methods. First, acoustic parameters important in the context of public address and sound reinforcement systems are recalled. A measurement methodology is presented that employs various test signals to determine impulse responses. The process of evaluating sound system performance, signals enabling...
-
An Industrial Survey on Business Analysis Problems and Solutions
PublicationThe paper focuses on the problems reported by business analysts which have a negative impact on their work and on the applicability of available business analysis (BA) techniques as solutions to such problems. A unified set of BA techniques was developed on the basis of 3 industrial standards associated with IIBA, REQB and IREB certification schemes. A group of 8 business analysts was surveyed to list problems they encounter in...
-
Methodological issues of functional safety and reliability assessment of critical systems in industrial hazardous plants
PublicationThe aim of this article is to identify and discuss some methodological issues that are of interest among functional safety specialists and experts after publication of the second edition of international standards IEC 61508 and IEC 61511, including the design and implementing the safety-related functions of higher safety integrity levels and protection layers. The basic role of safety-related systems is to reduce effectively and...
-
Detection of some volatile degradation products released during photoexposition of ranitidine in a solid state
PublicationRanitidine (RAN) is on top of the list of prescribed drugs, due to its popularity as a selective H2-receptor antagonist, which efficiently decreases the amount of acid produced in the stomach. RAN is not stable both in a solid state and in a solution, which creates manufacturing problems, requires appropriate storage conditions, and results in a short drug shelf-life. The aim of this work was to study the emission of volatile...
-
Defence in depth conception in nuclear power plants and requirements for instrumentation and control systems
PublicationThe aim of this article is to identify and discuss some issues of the safety systems’ design for nuclear power plants equipped with the light water reactors using a defence in depth (D-in-D) conception. Because the functional safety solutions play nowadays an important role for the risk control, the basic requirements for the instrumentation and control systems are specified with regard to relevant international standards. For...
-
Bridge Ergonomic Design: A Review
PublicationHuman error remains the most common cause of marine incidents and it is worth emphasizing that navigator’s performance is directly affected by ergonomic factors on the bridge. Studies regarding influence of bridge design and work environment on the operator are rare, thus the main purpose of this paper is to fill in this gap. Documents issued by recognized organizations, research publications and additional sources were reviewed...
-
An analytical approach to determine the health benefits and health risks of consuming berry juices
PublicationFood products composition analysis is a prerequisite for verification of product quality, fulfillment of regulatory enforcements, checking compliance with national and international food standards, contracting specifications, and nutrient labeling requirements and providing quality assurance for use of the product for the supplemen- tation of other foods. These aspects also apply to the berry fruit and berry juice. It also must...
-
Operational problems of constructed wetland for landfill leachates treatment: case study
PublicationIn the paper the quality fluctuations of leachate from municipal landfill in Gdansk (Poland) over the last 5 years and evaluation of a wetland system designed for treatment of the leachate are discussed.The research has been conducted during the 5 years period. The constructed wetland for leachate treatment, consisting of 2 horizontal subsurface flow reed beds, working in parallel was built in 2001. In the period 2005-06 it underwent...
-
Functional Safety Analysis including Human Factors
PublicationIn this paper selected aspects of human factors are discussed that should be taken into account during the design of safety-related functions for a complex hazardous installation and its protections. The layer of protection analysis (LOPA) methodology is used for simplified risk analysis based on defined accident scenarios. To control the risk the safety instrumented functions (SIFs) are identified and their safety integrity levels...
-
Measurements of ASON/GMPLS connection control layer performance according to the ETSI methodology
PublicationMeasurements of performance have always been crucial for evaluation of telecommunication systems, especially for implementation of network control elements responsible for connection handling which regards to bandwidth reservation, modification and release. That problem also arises in Automatically Switched Optical Network/Generalized Multiprotocol Label Switching (ASON/GMLPS) architecture, which is considered as one of the components...
-
Design of a Distributed System using Mobile Devices and Workflow Management for Measurement and Control of a Smart Home and Health
PublicationThe paper presents design of a distributed system for measurements and control of a smart home including temper- atures, light, fire danger, health problems of inhabitants such as increased body temperature, a person falling etc. This is done by integration of mobile devices and standards, distributed service based middleware BeesyCluster and a workflow management system. Mobile devices are used to measure the parameters and are...
-
Determination of terpene profiles in potential superfruits
PublicationThe aim of this work was to characterize and compare the profiles of volatile terpenes in four potential superfruits. These profiles were determined using headspace solid-phase microextraction coupled with comprehensive two-dimensional gas chromatography linked to time-of-flight mass spectrometry. The proposed technique allowed the separation and identification of 79 terpenes present in cape gooseberry, crabapple, cherry silver...
-
Strategies for Achieving Energy Neutrality in Biological Nutrient Removal Systems – a Case Study of the Slupsk WWTP (northern Poland)
PublicationThe paper presents a model-based evaluation of technological upgrades on the energy and cost balance in a large biological nutrient removal wastewater treatment plant (WWTP) in the city of Slupsk (northern Poland). The proposed upgrades include chemically enhanced primary sludge removal and reduction of the nitrogen load in the deammonification process employed for reject water treatment. Simulations enabled to estimate the increased...
-
Experimental Testbed of ASON/GMPLS architecture
PublicationThe paper presents the ASON/GMPLS architecture realized in the Department of Teleinformation Networks at Gdansk University of Technology based on the FSP 3000R7 ADVA Optical Networking platform. The FSP 3000R7 is a high-performance WDM networking system with GMPLS control plane for bidirectional transmission of optical signals. The system uses a modular structure which enables a flexible upgrade of capacity and functionality. The...
-
Strategies for achieving energy neutrality in biological nutrient removal systems - a case study of the Slupsk WWTP (northern Poland)
PublicationThe paper presents a model-based evaluation of technological upgrades on the energy and cost balance in a large biological nutrient removal wastewater treatment plant (WWTP) in the city of Slupsk (northern Poland). The proposed upgrades include chemically enhanced primary sludge removal and reduction of the nitrogen load in the deammonification process employed for reject water treatment. Simulations enabled to estimate the increased...
-
Procedure based functional safety and information security management of industrial automation and control systems on example of the oil port installations
PublicationThe approach addresses selected technical and organization aspects of risk mitigation in the oil port installations with regard to functional safety and security requirements specified in standards IEC 61508, IEC 61511 and IEC 62443. The procedure for functional safety management includes the hazard identification, risk analysis and assessment, specification of overall safety requirements and definition of...
-
Overview of Knowledge Management in Occupational Safety, Health, and Ergonomics
PublicationOccupational safety, health, and ergonomics (OSHE) are strategic pillars of contemporary organizations. In order to provide safer workplace, it is vital to manage the organizational knowledge, so that effective decision making along with absolute compliance to standards can be executed. The critical challenge for OSHE in modern industry is management of existing individual knowledge (experience), structure knowledge, and organizational...
-
Integrated Functional Safety and Cybersecurity Evaluation in a Framework for Business Continuity Management
PublicationThis article outlines an integrated functional safety and cybersecurity evaluation approach within a framework for business continuity management (BCM) in energy companies, including those using Industry 4.0 business and technical solutions. In such companies, information and communication technology (ICT), and industrial automation and control system (IACS) play important roles. Using advanced technologies in modern manufacturing...
-
System architecture of an INSPIRE-compliant green cadastre system for the EU Member State of Poland
PublicationIn response to the need for a sustainable agricultural policy, which would support activities such as decision making in precise agriculture and mitigation of crop threats, a concept agricultural information system was developed for the area of Poland. This innovative concept, called Green Cadastre (GC), proposes to create a uniform system designed for use on a national scale by both state administration as well as local farmers....
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Using On-line Measurement by Electronic Nose and Computer Simulations for Real-time Control at WWTP
PublicationContinuous investigation of wastewater quality can be carried out by a device called an e-nose. One important feature of the proposed real-time control system for WWTP is that using on-line measurements by e-nose together (Figure 1) with technological sets picked on this basis by means of computer models, it is possible to change treatment process parameters, depending on the current quality of wastewater. It can be used for the...
-
Radio Channel Measurements in Off-Body Communications in a Ferry Passenger Cabin
PublicationThis paper presents an off-body radio channel measurements in a ferry passenger cabin at 2.45 GHz band, for static sleeping scenarios with different body orientation and on-body antennas placements, and also for upper and lower sleeping berths. The measurements have been performed with two types of on-body wearable receiving antennas: FlexPIFA (flexible planar inverted F antenna), and FlexNotch (flexible adhesive-backed notch antenna)...
-
Influence and development of new kinematic systems in flat surface lapping
PublicationThe face grinding and lapping technology is widely used in the field of the precise and ultraprecise manufacturing. It has become an indispensable technology in the manufacture of many parts. An absence of material restrictions allows machining both metal and non-metallic materials, including technical ceramics [1]. Nowadays there are mainly two kinematic systems in lapping machines [2]. The machining plane-parallel surfaces is...
-
Application of a commercially available derivatization instrument and commonly used reagents to HPLC on-line determination of antioxidants
PublicationThis study demonstrates the potential of a commercially available derivatization instrument coupled with HPLC for separation and on-line determination of antioxidants detected with widely used screening reagents - DPPH (2,2-diphenyl-1-picrylhydrazyl), ABTS (2,2'-azino-bis(3-ethylbenzthiazoline-6-sulphonic acid) or FCR (Folin-Ciocalteu's phenol reagent ). As the result of optimization, key parameters of the analytical procedure,...
-
Determination of rectification corrections for semi gantry crane rail axes in the local 3D coordinate system
PublicationElectronic tacheometers are currently the standard instruments used in geodetic work, including also geodetic engineering measurements. The main advantage connected with this equipment is among others high accuracy of the measurement and thus high accuracy of the final determinations represented for example by the points’ coordinates. One of many applications of the tacheometers is the measurement of crane rail axes. This measurement...
-
Multifaceted Analyses of Four Different Prototype Lightweight Photovoltaic Modules of Novel Structure
PublicationDynamic growth of photovoltaic capacity in Poland encourages many entities to invest in photovoltaic systems. However, in the case of buildings with low roof-bearing capacity it can be problematic or even impossible to mount conventional PV modules due to their relatively high weight. Hence, the use of lightweight PV modules is a potential solution. In this paper four different prototype silicon lightweight modules of novel structure...
-
Novel ABTS-dot-blot method for the assessment of antioxidant properties of food packaging
PublicationThe new ABTS-dot-blot method for the direct determination of antioxidant activity of active packaging that is in contact with foodstuffs has been developed. The usefulness of the new method was verified with the use of agarose, pork gelatin, bacterial cellulose and cellulose-chitosan films with incorporated standard antioxidant – Trolox or plant phytochemicals derived from three types of berry juices (chokeberry, blue-berried honeysuckle,...
-
Implementation of the Concept of Flexicurity in the Selected Countries of Central Eastern Europe
PublicationThe CEE countries have to create their own flexicurity policies which would take into account the employment policy guidelines, cultural traditions and socio-economic development. The aim of this article is to examine and evaluate the implementation of the flexicurity concept on the basis of the adopted set of composite indicators. The study covers 9 countries of the CEE region, and the research period covers the years 2007 and 2013....
-
Proces oczyszczania ścieków komunalnych na przykładzie Oczyszczalni ścieków Gdańsk Wschód
PublicationArtykuł przedstawia proces funkcjonowania największej oczyszczalni ścieków w woj. pomorskim -Gdańsk Wschód. W artykule zostały przedstawione etapy modernizacji wskazanego zakładu pod kątem: poprawy skuteczności oczyszczania ścieków oraz zmniejszenia ilości zrzucanych zanieczyszczeń do Zatoki Gdańskiej w kontekście sprostania rygorystycznym standardom krajowym i unijnym.
-
Kształtowanie architektoniczne nadbudówki na statkach do przewozu kontenerów i samochodów.
PublicationW wyniku analizy wybranych typów statków, które były przedmiotem badań rozprawy stwierdzono, że niezależnie od lokalizacji nadbudówki w stosunku do głównych źródeł zagrożeń na statku, ukształtowanie poszczególnych grup pomieszczeń pozwoliło na wykorzystanie standartu użytkowego na dobrym europejskim poziomie w zależności od rozwiązań architektonicznych.
-
Praktyka wykonywania pomiarów instalacji fotowoltaicznych prowadząca do określenia rzeczywistego stanu technicznego
PublicationPraca przedstawia zasady wykonywania pomiarów instalacji fotowoltaicznych wg normy PN-EN 62446-1. Proponowany w normie zakres podstawowy pozwala tylko na ocenę bezpieczeństwa pracy instalacji. Dopiero zakres dodatkowy umożliwia uzyskanie informacji o referencyjnych mocach zainstalowanej elektrowni, jej sprawności, a nawet jednorodności poszczególnych ogniw fotowoltaicznych. Załączone przykłady pomiarów czystych i zabrudzonych paneli...