Search results for: EUTECTIC SOLVENTS
-
Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects
PublicationMetallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...
-
Green chromatography
PublicationAnalysis of organic compounds in samples characterized by different composition of the matrix is very important in many areas. A vast majority of organic compound determinations are performed using gas or liquid chromatographic methods. It is thus very important that these methods have negligible environmental impact. Chromatographic techniques have the potential to be greener at all steps of the analysis, from sample collection...
-
Investigation of use of hydrophilic/hydrophobic NADESs for selective extraction of As(III) and Sb(III) ions in vegetable samples: Air assisted liquid phase microextraction and chemometric optimization
PublicationIn this paper, a green, cost-effective sample preparation method based on air assisted liquid phase microextraction (AA-LPME) was developed for the simultaneous extraction of As(III) and Sb(III) ions from vegetable samples using hydrophilic/hydrophobic natural deep eutectic solvents (NADESs). Central composite design was used for the optimization of extraction factors including NADES volume, extraction cycle, pH, and curcumin concentration....
-
Betaine and L-carnitine ester bromides: Synthesis and comparative study of their thermal behaviour and surface activity
PublicationSix esters of both betaine and L-carnitine bromides, featuring alkyl groups ranging from C8 to C18 in length, have been synthesized. The thermal behaviour of these twelve bio-based salts has been analyzed and compared by thermal gravimetric analysis and differential scanning calorimetry. The L-carnitine alkyl ester bromides melted below 100 C and can hence be considered ionic liquids (ILs) with full rights. Conversely, the betaine...
-
Process Control of Biogas Purification Using Electronic Nose
PublicationNowadays, biogas produced from landfills and wastewater treatment plants or lignocellulosic biomass is important sustainable and affordable source of energy. Impurities from biogas stream can cause a serious odor problem, especially for residents of areas immediately adjacent to production plants. Therefore, biogas pre-treatment is necessary to protect engines that convert biogas into energy and in order to increase the specific...
-
Metrics for green analytical chemistry
PublicationGreen analytical chemistry, although not being a new concept, does not have a greenness metrics system. Green chemistry metrics are not suitable for analytical procedure assessment because they often refer to the mass of the product. Some efforts have been made to develop suitable metrics for analytical chemistry. Some are simple to use but do not cover all aspects of analytical methods’ environmental impact. Others are more comprehensive...
-
Analytical data on molecular umbrella: cispentacin and molecular umbrella: fluorescent probe conjugates
Open Research DataAnalytical data (NMR, MS, FTIR) for nine conjugates of molecular umbrella with cispentacin, Lys(Mca) or Nap-NH2. The conjugates have been rationally designed as potential antifungal agents. 1H NMR and 13C NMR spectra were obtained at 500 MHz Varian Unity Plus spectrometer and the deuterated solvents were used as internal locks. High-resolution mass...
-
Initial Considerations
PublicationChemical processes have made use of a wide number of volatile organic solvents due to their efficiency in countless unit operations. The increasing knowledge on the environmental, health, and safety hazards associated to their use has significantly contributed to the search for greener alternatives. The primary purpose of this book is to provide an overview of alternative solvents with reduced issues that have successfully replaced...
-
Ionic liquids for nano- and microstructures preparation. Part 2: Application in synthesis
PublicationIonic liquids (ILs) are widely applied to prepare metal nanoparticles and 3D semiconductor microparticles. Generally, they serve as a structuring agent or reaction medium (solvent), however it was also demonstrated that ILs can also play a role of a co-solvent, metal precursor, reducing as well as surface modifying agent. The crucial role and possible types of interactions between ILs and growing particles have been presented in...
-
Performance tuning of chitosan-based membranes by protonated 2-Pyrrolidone-5-carboxylic acid-sulfolane DES for effective water/ethanol separation by pervaporation
PublicationToday, the applicability of deep eutectic solvents (DES) in various fields, including membrane science and technology, is extensively investigated. In pioneering works, we have implemented different DES as a component of chitosan (CS)-based flat membranes for pervaporation (PV) separation. Herein, we present a new protonated (by sulphuric acid) 2-Pyrrolidone-5-carboxylic acid: sulfolane DES, as a green additive for its chemical...
-
Application of Aqueous Biphasic Systems Extraction in Various Biomolecules Separation and Purification: Advancements Brought by Quaternary Systems
PublicationAqueous biphasic systems (ABS) extraction is a simple, selective, efficient and easy to scale-up technology that, over the years, has attracted a considerable attention from the researcher community as an alternative methodology in downstream processing of a wide variety of biomolecules. This review summarizes and discusses the fundamental features of ABS, as well as its advantages and disadvantages, as a separation and purification...
-
Management of Dark Fermentation Broth via Bio Refining and Photo Fermentation
PublicationLignocellulose and starch-based raw materials are often applied in the investigations regarding biohydrogen generation using dark fermentation. Management of the arising post-fermentation broth becomes a problem. The Authors proposed sequential processes, to improve the efficiency of both hydrogen generation and by-products management carried under model conditions. During the proposed procedure, the simple sugars remaining in...
-
Membrane separation processes for the extraction and purification of steviol glycosides: an overview
PublicationSteviol glycosides (SGs), as natural sweeteners from Stevia rebaudiana, are currently employed for replacing sugar and its derivatives in several food products and formulations. Such compounds play an essential role in human health. Their usage provides a positive effect on preventing diseases related to sugar consumption, including diabetes mellitus, cancer, and lipid metabolism disorders. The traditional extraction of SGs is...
-
2,6-Bis((benzoyl-R)amino)pyridine (R = H, 4-Me, and 4-NMe2) Derivatives for the Removal of Cu(II), Ni(II), Co(II), and Zn(II) Ions from Aqueous Solutions in Classic Solvent Extraction and a Membrane Extraction
Publication -
How green are ionic liquids? – A multicriteria decision analysis approach
PublicationDue to various desirable physicochemical properties, ionic liquids (ILs) are still gaining in popularity. ILs have been recurrently considered green solvents. However, environmental, health and safety assessments of ILs have raised certain doubts about their benignness, and their greenness status is currently unclear. To clarify the situation on their greenness, we perform a comprehensive assessment of more than 300 commercially...
-
Temperature of formation of Au nanostructures
Open Research DataNanostructures were obtained via annealing of thin Au films. In order to determine possible nanoislands formation mechanisms, dependence on initial film thickness was examined. For the surface morphology studies, nanograin structure and chemical composition analysis, SEM, HR TEM and EDS measurements were performed, respectively. Morphology studies shown...
-
The dispersive micro-solid phase extraction method for MS-based lipidomics of human breast milk*
PublicationA simple and rapid microextraction method ensuring high lipidome coverage was developed for liquid chromatography mass spectrometry (LC-MS)-based lipidomics of human breast milk. The dispersive microsolid phase extraction (D-µ-SPE) technique, coupled with the design of experiment (DoE) method, enabled the study of the influence of several conditions (desorption solvent, stationary phase ratio, and sorption and desorption time)...
-
Porosity and swelling properties of novel polyurethane–ascorbic acid scaffolds prepared by different procedures for potential use in bone tissue engineering
PublicationIn this work, a novel polyurethane (PU) system based on poly(ethylene-butylene) adipate diol, 1,6-hexamethylene diisocyanate, 1,4-butanediol, and ascorbic acid was used to prepare scaffolds with potential applications in bone tissue engineering. Two fabrication methods to obtain porous materials were chosen: phase separation (PS)/salt particle leaching (PL) and solvent casting (SC)/salt PL. The calculated porosity demonstrated...
-
Ultrasound assisted extraction
PublicationThe use of green and sustainable extraction techniques is very popular topic in the multidisciplinary area of chemistry, biology and technology. There is no doubt that extraction constitutes a very important step of analytical procedures of separation, detection, identification and determination of wide spectrum analytes from samples characterized by complex and very often nonhomogeneous composition of matrix. Traditional techniques...
-
A Green Chemistry "environmentally friendly" approach to the synthesis of chloro-intermediates of ephedrine/pseudoephedrine
PublicationMethylamphetamine is an addictive stimulant drug that strongly activates certain systems in the brain. It is closely related chemically to amphetamine, but the central nervous system effects of methamphetamine are greater. There is much interest in methylamphetamine among scientists and therefore the synthesizes of methylamphetamine and its metabolites are carried out on a large scale in chemical laboratories. Globally, ephedrine...
-
Photophysics of Soret-Excited Tin(IV) Porphyrins in Solution
PublicationThe photophysics of low-chlorin tin(IV) tetraphenylporphyrin dihydroxide, a core building block for axially substituted supramolecular tin porphyrin constructs, has been studied in a variety of hydrogen-bonding, nonpolar, and aprotic polar solvents using steady-state, nanosecond, and femtosecond time-resolved emission, and femtosecond time-resolved absorption methods. In hydrogen-bonding solvents the metalloporphyrin exists as...
-
Green sample preparation techniques for chromatographic determination of small organic compounds
PublicationAccurate monitoring of the state of the environment requires the introduction of additional isolation and/or preconcentration step prior to the chromatographic determination. In this work the information about novel methodological and instrumental solutions in relation to different variants of microextraction techniques are presented. Attention is focused on analytical procedure and suitable analytical tools for extraction of the...
-
Evaluation of the Greenness of Analytical Procedures
PublicationThis contributions introduces the need to develop the methods to evaluate analytical procedures in the light of green analytical chemistry. Green chemistry metrics are not applicable in analytical chemistry because they refer to the mass of product and no product with mass is generated during analytical determination. Analytical greenness evaluations are based on scoring - such as NEMI or Eco-scale or comparative analysis as it...
-
A review: Fabrication of porous polyurethane scaffolds
PublicationThe aim of tissue engineering is the fabrication of three-dimensional scaffolds that can be used for the reconstruction and regeneration of damaged or deformed tissues and organs. A wide variety of techniques have been developed to create either fibrous or porous scaffolds from polymers, metals, composite materials and ceramics. However, the most promising materials are biodegradable polymers due to their comprehensive mechanical...
-
The Sonocatalytic Activation of Persulfates on Iron Nanoparticle Decorated Zeolite for the Degradation of 1,4-Dioxane in Aquatic Environments
PublicationIn the chemical industry, 1,4-diethylene dioxide, commonly called dioxane, is widely used as a solvent as well as a stabilizing agent for chlorinated solvents. Due to its high miscibility, dioxane is a ubiquitous water contaminant. This study investigates the effectiveness of catalyst- and ultrasound (US)-assisted persulfate (PS) activation with regard to degrading dioxane. As a first step, a composite catalyst was prepared using...
-
Aqueous Biphasic Systems Using Chiral Ionic Liquids for the Enantioseparation of Mandelic Acid Enantiomers
Publication -
DETERMINATION OF SURFACTANTS IN ENVIRONMENTAL SAMPLES - PART I. CATIONIC COMPOUNDS = Oznaczanie Surfaktantów W Próbkach Środowiskowych. Część I. Związki Kationowe
PublicationCompounds from the group of cationic surfactants are widely applied in household, industrial, cleaning, disinfectant, cosmetic and pharmaceutical products as their specific properties (antimicrobial, emulsifying, anticorrosion, softening). After use, cationic surfactants are disposed to wastewater-treatment plants and finally with effluent water to surface waters due to their incomplete degradation. Moreover, they can freely circulate...
-
The XPS studies of the CB-PLA electrodes after different surface treatments (chemical, electrochemical, enzymatic)
Open Research DataThe dataset contains the Xray Photoelectron Spectroscopy results of the studies performed under different conditions of surface activation of the CB-PLA 3D printed electrodes. The activation was performed by hydrolysis in different solvents (DMF, 1M HCl, 1M NaOH), electrolysis in 1M NaOH, enzymatic treatment in polymerase or simultaneous electrolysis...
-
XPS study of the NH4-VOx powders
Open Research DataVanadium pentoxide samples were prepared by sol-gel method. The starting solution was prepared by mixing vanadium (V) oxytripropoxide (Aldrich) in an anhydrous ethanol as solvent and acetylacetone. By drying the sol at 323 K for 48 h, it transforms via gel into a xerogel powder. Next, the precursor powder was pressed into the disk-shaped pellets. Samples...
-
Application of Multivariate Adaptive Regression Splines (MARSplines) for Predicting Hansen Solubility Parameters Based on 1D and 2D Molecular Descriptors Computed from SMILES String
PublicationA new method of Hansen solubility parameters (HSPs) prediction was developed by combining the multivariate adaptive regression splines (MARSplines) methodology with a simple multivariable regression involving 1D and 2D PaDEL molecular descriptors. In order to adopt the MARSplines approach to QSPR/QSAR problems, several optimization procedures were proposed and tested. The effectiveness of the obtained models was checked via standard...
-
Analysis of pesticide residue in fruits and vegetables using analytical analytical protocol based on application of QuEChERS technique and GC-ECD system
PublicationQuEChERS sample preparation method was used for the determination of 10 pesticides and their metabolites in fruits (apple, grape) and vegetables (tomato, paprika), coupled to gas chromatography with electron capture detector (GC-ECD). The experimental parameters including amount of the sample, types of solvents, extraction time and types of sorbent at the purification stage were optimized. The GC-ECD method was validated in terms...
-
Green analytical chemistry metrics: A review
PublicationGreen analytical chemistry encourages reducing the use of toxic chemicals/reagents, using energy-efficient equipment, and generating minimal waste. The recent trends in analytical method development focus on the miniaturization of the sample preparation devices, the development of solventless or solvent-minimized extraction techniques, and the utilization of less toxic solvents. The twelve principles of GAC serve as a basic guideline...
-
Bio-based semi-aromatic polyesters for coating applications
PublicationLinear and branched bio-based semi-aromatic (co)polyesters were evaluated as resins for solvent-basedand powder coatings. Dimethyl-2,5-furandicarboxylate (DMF), 2,3-butanediol and various multifunc-tional comonomers were used to synthesize amorphous hydroxyl-end-capped (co)polyesters. The resinswere cross-linked using the -caprolactam blocked trimer of isophorone diisocyanate. Both the solvent-based and powder coatings proved to...
-
Exploring the cocrystallization potential of urea and benzamide
PublicationThe cocrystallization landscape of benzamide and urea interacting with aliphatic and aromatic carboxylic acids was studied both experimentally and theoretically. Ten new cocrystals of benzamide were synthesized using an oriented samples approach via a fast dropped evaporation technique. Information about types of known bi-component cocrystals augmented with knowledge of simple binary eutectic mixtures was used for the analysis...
-
Ground tire rubber functionalization as a promising approach for the production of sustainable adsorbents of environmental pollutants
PublicationWaste tires management and further utilization are currently one of the biggest concerns regarding the environment and human health protection. At present, shredding, grinding, or pulverization of waste tires are the most popular options for industrial recycling. Although many solutions for ground tire rubber (GTR) applications were checked and verified so far, their further implementation at an industrial scale is still very limited....
-
Evaluation of Green Sample Preparation Techniques for Organic Compounds
PublicationNowadays, Green Analytical Chemistry (GAC) idea is of high importance, with impact on the rapid growth in the sample preparation area with special emphasis on sample preparation simplification, miniaturization and automation. Due to the fact that GAC is of high importance today, this study is focused on the evaluation of green sample preparation techniques for organic compounds. It is well known that sample preparation is considered...
-
SEM micrographs of NH4VO3 crystals - molar concetration factor
Open Research DataThe DataSet contains the scanning electron microscopy (SEM) micrographs of NH4VO3 nano_crystals obtained by the LPE-IonEx method. The SEM images clearly show that the morphology of the end product can be nicely tuned by changing the molar concentration of ammonium salt in the solvent.
-
Improving carbon dioxide capture in aqueous ammonia solutions by fine SiO2 particles
PublicationAmmonia solutions are considered to be effective solvents for carbon dioxide absorption. Despite the numerous advantages of these solvents, their high volatility is a significant technical and economic problem. Therefore, in this work, silica particles were used as additives to improve CO2 absorption and inhibit NH3 desorption. SiO2 microparticles and colloidal SiO2 particles in the concentration range of 0-0.15 wt.% were used...
-
An improved scalable method of isolating asphaltenes
PublicationA new, improved and scalable procedure of asphaltene fraction isolation is presented and compared to standard test methods. The new procedure uses 1:40 feedstock to solvent (n-heptane) ratio (g/mL), filtration through a cellulosic thimble and extensive washing in a Soxhlet type extractor. The group type composition and purity of the asphaltene fractions have been examined using thin-layer chromatography with flame-ionization detection....
-
Challenges in determination of pesticides from various chemical groups in fruits and vegetables applying QuEChERS method
PublicationPesticides are a large group of compounds with different physical and chemical properties, which place some of them among the most toxic, environmentally stable, and mobile substances. Nevertheless, their number, use, and application are continuously expanding. A consequence of their use is the possible presence of residues in treated food products. To protect consumers from exposure to unacceptable levels of pesticides Maximum...
-
Ionic liquids-based microextraction techniques
PublicationIn recent years, the development of highly efficient analytical techniques is of great importance, however, the direct analysis of complex sample matrix is still impossible in many cases. Therefore, the step of sample preparation is commonly involved in an analytical procedure. Over the years, it has been realized that the major source of inaccuracy and imprecision on general analysis results from the operations associated to sample...
-
Implementation of multicriteria decision analysis in design of experiment for dispersive liquid-liquid microextraction optimization for chlorophenols determination
PublicationA novel and efficient approach to optimization of extraction step prior the chromatographic determination of nine chlorinated phenols is described. It is based on the combination of design of experiments and multicriteria decision analysis. Such an approach is used to optimize dispersive liquid-liquid microextraction procedure for the determination of 9 chlorophenols in water samples. Three parameters are optimized – sample volume,...
-
Experimental and theoretical studies on the Sulfamethazine-Urea and Sulfamethizole-Urea solid-liquid equilibria
PublicationThe miscibility of active pharmaceutical ingredients with excipients is an important aspect in pharmaceutical technology protocols. In this study, the differential scanning calorimetry (DSC) was used for Sulfamethazine-Urea (SI–U) and Sulfamethizole-Urea (SO–U) solid-liquid phase diagrams determination. Both sulfonamides form simple binary eutectics with Urea. The lack of new co-crystal phase formation was confirmed by inspection...
-
Analytical chemistry with biosolvents
PublicationOne of the current trends in green analytical chemistry is the introduction of green solvents, some of which are biobased. At the same time, the development of the biorefinery concept has allowed more biochemicals to be obtained with increased efficiency and from a wider range of feedstocks. The first examples of the use of biosolvents in analytical applications included extractions performed with alcohols, esters, and terpenes....
-
DETERMINATION OF SURFACTANTS IN ENVIRONMENTAL SAMPLES. PART II. ANIONIC COMPOUNDS
PublicationSurfactants (SAA) with negative charge of polar group are named as anionic compounds. They are main constituent of most products containing synthetic surfactants. The linear alkylbenzene sulfonates (LAS), alkyl ethoxysulfates (AES) and alkyl sulfates (AS) are typically applied from this class of compounds. Those surfactants are ingredients of household detergents and cleaners, laundry detergents, cosmetic. Moreover they can be...
-
Microwave assisted liquefaction with crude glycerol as a potential method of brewer's spent grain utylization
PublicationBrewer's spent grain was applied as a low-cost industrial type of lignocellulose biomass in a liquefaction and solvent: biomass ratio on the efficiency of the process, chemical structure and basic properties of obtained prepared polyols and soil residues shed light on the biomass degradation mechanism through application of microwaves and further reaction of degradation products with solvent particles.
-
Molecularly imprinted polymers applied in capillary electrochromatography and electrophoresis techniques
PublicationMolecularly imprinted polymers (MIPs) are synthetic materials with predetermined selectivity for a particular analyte or group of structure-linked chemicals which make them an ideal separation component. The process of developing and applying new types of MIPs in the field of environmental analytical chemistry has been broadly discussedi n many scientific studies in recent years. The use of new types of MIP sorbents as unique sorption...
-
AFM imaging of surface of modern soldering alloy
Open Research DataFollowing the announcement in 2006 of European Union directives aimed at limiting the use of lead in electronic products, there was an urgent need to use lead-free solders in the electronics industry. Due to production requirements, it is necessary to use solders with different melting points. To replace the low-melting eutectic Sn 37 wt. Pb, the most...
-
Application of dispersive liquid - liquid microextraction for determination of pesticides from various chemical groups in water samples
PublicationPesticides are a global risk because they move with the wind, rain and sea currents from other regions, which makes getting to places which were never used before. Their presence was detected in all types of water circulating in the ecosystem, which is an easy source of exposure to life and health of all living organisms. Currently, it is considered one of the most dangerous and toxic pollutants, which fate and function is still...
-
Linear and branched polyester resins based on dimethyl-2,5-furandicarboxylate for coating applications
PublicationIn this study, novel bio-based hydroxyl-functional (co)polyesters from dimethyl-2, 5-furandicarboxylate (DMF), 2,3-butanediol, and a variety of comonomers viz. glycerol, pentaerythritol or trimethylolpropane are prepared using a solvent-free, bulk polycondensation technique. Extensive molecular and thermal characterization was performed to elucidate the properties of these materials. The materials showed suitable properties for solvent-borne...