Publications
Filters
total: 633
Catalog Publications
-
Ekspertyza techniczna dotycząca dynamiki mostu MD7 w ciągu S-7 nad rzeką Wisłą
PublicationCelem opracowania jest analiza odpowiedzi dynamicznej mostu podwieszonego MD7 w ciągu S-7 nad rzeką Wisłą wraz z estakadami dojazdowymi pod kątem interpretacji wyników pozyskanych z badań pod próbnym obciążeniem dynamicznym, wyników symulacji numerycznych oraz danych pomiarowych z systemu monitoringu technicznego.
-
Lamb wave propagation in a single lap adhesive joint
PublicationThe aim of the paper is the analysis of Lamb wave propagation in adhesive joints. The research was performed on a single lap adhesive joint of two steel plates. Two types of joints, namely an intact and with defect were considered. In experimental investigations the condition assessment of the joint was performed with the use of antisymmetric Lamb waves excited by a plate piezo actuators and measured by a laser vibrometer. Numeri-cal...
-
Optymalizacja projektu montażu obiektu MS-4/B realizowanego w ramach zadania „Budowa drogi ekspresowej S7 na odc. Miłomłyn-Olsztynek, Pododcinek Ostróda Północ - Ostróda Południe, w ciągu drogi S7 wraz z budową obwodnicy Ostródy w ciągu DK 16 (Pododcinek "B")” wraz z uzgodnieniami z nadzorem autorskim i nadzorem naukowym
PublicationCelem opracowania jest przeprowadzenie optymalizacji projektu montażu obiektu MS-4/B realizowanego w ramach zadania „Budowa drogi ekspresowej S7 na odc. Miłomłyn-Olsztynek, Pododcinek Ostróda Północ - Ostróda Południe, w ciągu drogi S7 wraz z budową obwodnicy Ostródy w ciągu DK 16 (Pododcinek "B")” oraz uzgodnienie wprowadzonych zmian z Nadzorem Autorskim (NA).
-
Zagadnienia modelowania procesu produkcji wodoru dla potrzeb energetyki w reakcji dekompozcji metanolu w innowacyjnych reaktorach termokatalitycznych ze stopu Ni3Al
PublicationZagadnienia modelowania procesu produkcji wodoru dla potrzeb energetyki w reakcji dekompozcji metanolu w innowacyjnych reaktorach termokatalitycznych ze stopu Ni3Al
-
From a Point Cloud to a 3D Model - an Exercise for Users of AutoCAD and Revit
PublicationThe paper presents a proposal of the topic of an exercise for students of building faculties as part of classes on 3D modelling. The task consists in creating a three-dimensional model based on the measurement obtained with the Leica P30 laser scanner. Due to the maximum number of points in the cloud in the presented programs, the output files must be properly cleared and reduced. The point cloud was pre-processed in Cyclone software....
-
Enhanced energy conversion as a result of fluid-solid interaction in micro- and nanoscale
PublicationIt is known that nano- and micromechanics require new approaches to right describing of surface-like phenomena which lead to an enhanced energy conversion. In this work, a general form of surface forces that consist of a contribution from both the friction and mobility components has been extended to collect the effects of bulk and surface motion of a fluid. Quite similar impact can be observed for a solid-fluid mixture, where...
-
Proximal fibular osteotomy as a treatment for degenerative meniscal extrusion
PublicationMeniscal extrusion treatment is a key focus area for research and clinical study of degenerative knee pathology. The contact forces between the meniscus and the bones cause external displacements of the meniscus that are resisted by the circumferential fibres. The main risk factors for the excessive deformation of the meniscus are meniscal root tears, disruption of the circumferential fibres, knee malalignment and high body mass...
-
wyKOMBinuj mOst 2016 – ogólnopolski konkurs budowy mostów z papieru
PublicationW dniach 4–6 maja 2016 roku po raz kolejny odbył się ogólnopolski konkurs konstruktorski „wyKOMBinuj mOst 2016” organizowany przez Koło Naukowe Mechaniki Budowli KoMBo z Wydziału Inżynierii Lądowej i Środowiska. Była to już 9. edycja wydarzenia, które na przestrzeni lat zyskało renomę i prestiż w całej Polsce.
-
System monitoringu technicznego w obiektach mostowych - niezbędne czy przydatne?
PublicationW pracy przedstawiono rozważania na temat zasadności stosowania systemów monitoringu technicznego w mostach. Wskazano rodzaje systemów oraz przykłady zastosowań: utrzymanie, bezpieczeństwo oraz weryfikacja założeń projektowych.
-
Cooperation areas between universities and industry - case studies in the area of civil engineering
PublicationThe paper describes the areas of cooperation between universities and industry in the area of civil engineering. Presented examples are related to didactics, research grants and commissioned works. On the basis of the authors own experiences the mutual benefits of cooperation in different areas are described. As well as the assessment criteria of the areas of cooperation by the scientific community. The first area of cooperation...
-
3 Hz – WYMÓG KONIECZNY?
PublicationReferat jest pewnym przyczynkiem do dyskusji nad formalnymi uwarunkowaniami ujętymi w różnych dokumentach, a dotyczących wymagań z zakresu dynamiki mostów. W szczególności zapisu cyt.: ,,Stany graniczne użytkowania uważa się za przekroczone, jeżeli wymagania użytkowe dotyczące konstrukcji obiektu nie są dotrzymane. Oznacza to, że w konstrukcji obiektu nie powinny wystąpić: … 4) drgania własne o częstotliwości mniejszej niż 3 Hz”;...
-
Analiza możliwości wykorzystania propagacji fal sprężystych do diagnostyki nakładkowego połączenia dźwigara blachownicowego
PublicationW pracy przedstawiono wyniki analiz doświadczalnych propagacji fal sprężystych w modelu połączenia nakładkowego dwuteowego dźwigara blachownicowego. W testach wykorzystano zestaw urządzeń do generacji i akwizycji sygnałów oraz przetworniki piezoelektryczne. Badano możliwość wykrycia całkowitego poluzowania pojedynczych śrub i grup łączników przy zastosowaniu wzbudzenia punktowego i liniowego. Przeprowadzone analizy z wykorzystaniem...
-
Projekt i analizy obliczeniowe kładki dla pieszych przez rz. Motławę w Gdańsku
PublicationArtykuł dotyczy projektu oraz analiz obliczeniowych wykonanych dla kładki dla pieszych przez rzekę Motława w Gdańsku. Na podstawie zwycięskiej koncepcji ogłoszonego w 2012 roku przez miasto Gdańsk konkursu zgłoszonej przez słoweńskie biuro PONTING zespół MOSTY GDAŃSK opracował projekt budowlany i wykonawczy konstrukcji. Wykonano zaawansowane statyczne i dynamiczne obliczenia MES. Ich celem było jak najlepsze odzwierciedlenie pracy...
-
Composite Sandwich Footbridge – Numerical ESL FEM Calculations vs. In Situ Measurements
PublicationSelected results of the static analysis of composite sandwich footbridge with the corresponding in situ measured values are compared in the paper. The analysed bridge is a research object, which was built in 2015 and is currently located at the Gdańsk University of Technology campus. Since it is a novel structure, a proper definition of the bridge numerical model, allowing its safe design, is very important. Therefore, instead...
-
Analizy obliczeniowe sieci ciepłowniczej w ramach realizacji nowego odcinka Al. Niepodległości w Białymstoku na osiedlach: Starosielce, Zielone Wzgórza i Leśna Dolina
PublicationOpracowanie zawiera wyniki analiz obliczeniowych dot. sieci ciepłowniczych wykonanych z rurociągów klasy C.
-
Seminarium Baltazar Open Days
PublicationArtykuł syntetycznie przedstawia zagadnienia poruszone podczas seminarium dotyczącego konstrukcji kompozytowych Baltazar Open Days 2016, które odbyło się w dniach 6-8.12.2016 w Ostródzie.
-
Opinia techniczna nt. zachowania dynamicznego zaprojektowanej kładki nad ul. Szarych Szeregów w Radomiu
PublicationOpracowanie przedstawia opinię nt. zachowania dynamicznego kładki nad ul. Szarych Szeregów w Radomiu, która ma być realizowana przez VISTAL GDYNIA S.A.
-
Ekspertyza techniczna dot. uwarunkowań w zakresie dynamiki mostów
PublicationReferat jest pewnym przyczynkiem do dyskusji nad formalnymi uwarunkowaniami ujętymi w różnych dokumentach, a dotyczących wymagań z zakresu dynamiki mostów. W szczególności zapisu cyt.: ,,Stany graniczne użytkowania uważa się za przekroczone, jeżeli wymagania użytkowe dotyczące konstrukcji obiektu nie są dotrzymane. Oznacza to, że w konstrukcji obiektu nie powinny wystąpić: … 4) drgania własne o częstotliwości mniejszej niż 3 Hz”;...
-
Ekspertyza techniczna dotycząca drgań konstrukcji mostu w km 26,571/26,578 linii kolejowej nr 4 (CMK) w m. Huta Zawadzka
PublicationOpracowanie zawiera wyniki symulacji obliczeniowych, których celem bylo wyjaśnienie przyczyn nadmiernych drgań wieszaków wiaduktu kolejowego.
-
Betonowe nawierzchnie przepuszczalne w obliczu systemów wielokryterialnych oceny.
PublicationCoraz większym zainteresowaniem cieszą się obecnie nawierzchnie betonowe, które dobrze współgrają, a zarazem kontrastują sie z technologiami takimi jak asfalt, płyty chodnikowe, kostka brukowa itp. Wciąż ulepsza się i poszukuje nowych, niestandardowych rozwiązań i zastosowań dla nawierzchni betonowych. Obecnie nie liczy sie jedynie pomysł, ale również to w jako sposób określony element będzie oddziaływał na człowieka i środowisko....
-
Analizy obliczeniowe przebudowywanej sieci ciepłowniczej w ramach realizacji zadania „Nowy przebieg drogi krajowej nr 91 – odcinek Trasy Wschodniej od pl. Daszyńskiego do ul. Grudziądzkiej w Toruniu”
PublicationOpracowanie zawiera wyniki analiz obliczeniowych dot. sieci ciepłowniczych wykonanych z rurociągów klasy C.
-
Opracowanie ekspertyzy technicznej dot. nośności kompozytowego przęsła mostu dla pieszych
PublicationW opracowaniu przedstawiono charakterystyki materiałów oraz wyniki badań i obliczeń statyczno – wytrzymałościowych przekazanego Gminie Miasta Pruszcz Gdański kompozytowego przęsła mostu dla pieszych wykonanego jako obiekt badawczy w ramach projektu FOBRIDGE pt. ,,Opracowanie kompozytowych przęseł mostów dla pieszych do zastosowania nad drogami GP” współfinansowanego przez Narodowe Centrum Badań i Rozwoju w ramach umowy nr PBS1/B2/6/2013,...
-
Kompozytowy most dla pieszych. Badania doświadczalne i przygotowanie do projektowania
PublicationDysertacja powstała w ramach grantu badawczego NCBiR, pt. „Opracowanie kompozytowych przęseł mostów dla pieszych do zastosowania nad drogami GP”, nr PBS1/B2/6/2013. Głównym celem pracy było wsparcie procesu projektowania kompozytowego mostu pieszo-rowerowego. Zakres pracy obejmuje badania doświadczalne elementów kompozytowych GFRP, walidację modeli obliczeniowych oraz wykorzystanie aparatu analizy wrażliwości do procesu projektowego....
-
Ekspertyza techniczna dot. wpływu drgań na obiekt „Targ Rakowy i Sienny” w kompleksie Forum Gdańsk
PublicationEkspertyza dotyczy obiektu przekrywającego tory kolejowe w rejonie Targu Siennego i Targu Rakowego w Gdańsku stanowiącego część kompleksu Forum Gdańsk określającej wpływ ruchu kolejowego na konstrukcję oraz na użytkowników obiektu.
-
Ekspertyza techniczna dot. belek strunobetonowych typu MG
PublicationOpracowanie ma na celu zaopiniowanie rozwiązań projektowych dotyczących prefabrykowanych (reprezentatywnych) belek strunobetonowych typu MG. Belki mają być stosowane w obiektach zespolonych beton-beton o schematach statycznych swobodniepodpartych, uciąglonych (dwuprzęsłowych) oraz ramowych.
-
Przeprowadzenie pomiarów i wykonanie opinii mającej na celu określenie wpływu drgań na halę magazynową oraz przebywających w niej i pomieszczeniach biurowych ludzi
PublicationW opracowaniu przedstawiono rezultaty prac eksperckich, kóre polegały na przeprowadzeniu pomiarów i wykonaniu opinii mającej na celu określenie wpływu drgań wywołanych przez pracujące urządzenia na halę magazynową zlokalizowaną przy ul. Energetycznej 9 w Kowalach oraz przebywających w pomieszczeniach biurowych ludzi.
-
Ekspertyza techniczna dot. stref zakotwień kabli sprężających – obiekt MS-6 w ciągu S7
PublicationOpracowanie zawiera wyniki badań i symylacji MES na temat stref zakotwień wewnętrznych kabli sprężenia podłużnego oraz wskazuje na przyczyny przemieszczenia biernych bloków kotwiących wewnętrznych kabli sprężenia podłużnego przęsła 7-8 mostu MS-6 zlokalizowanego w drogi krajowej S-7 na odcinku Miłomłyn – Olsztynek.
-
Examples of Original Descriptive Geometry Task Items
PublicationThe paper presents several descriptive geometry drawing tasks and a comprehensive approach to their evaluation. The results as the task profile include the most important features and enable interpretation of the tasks in the educational system.
-
Domieszki przeciwmrozowe i ich stosowanie w niskich temperaturach
PublicationProwadzenie monolitycznych robót betonowych w okresie jesienno-zimowym wciąż stanowi istotny problem w budownictwie.Główny problem stanowi niewłaściwe wykonywanie robót betoniarskich w okresie ujemnych temperatur. Za produkty, które umożliwiają reakcje cementu z wodą w ujemnych temperaturach uważa się domieszki przeciwmrozowe. Ich stosowanie umożliwia obniżenie temperatury krzepnięcia wody poniżej 0oC, przyspiesza wiązanie i podnosi...
-
Diagnostyka żelbetowej kładki dla pieszych z zastosowaniem metody georadarowej
PublicationMetoda georadarowa, jako jedna z technik nieniszczących, znalazła szerokie zastosowanie w diagnostyce obiektów budowlanych. Z powodzeniem wykorzystuje się ją do oceny stanu technicznego konstrukcji żelbetowych określając rozkład i liczbę prętów zbrojeniowych, a także możliwe uszkodzenia. W pracy przedstawiono badania doświadczalne przeprowadzone na żelbetowej kładce dla pieszych z wykorzystaniem metody georadarowej. W celu poprawnej...
-
Symulacje przepływu ciepła przez płytę betonową
PublicationW pracy przedstawiono symulacje numeryczne dojrzewania betonu w płycie górnej skrzynki czteroprzęsłowego mostu typu extradosed. Model matematyczny opisujący przepływ ciepła dedykowany jest do prognozowania dojrzałości i wytrzymałości twardniejącego betonu. Proponowany model zaimplementowano w autorskim programie numerycznym napisanym w środowisku Matlab. Podejście numeryczne zweryfikowano za pomocą danych doświadczalnych uzyskanych...
-
Monitoring dojrzewania betonu skrzynki mostu MS3/B DK-16 - sekcja S3.18P
PublicationCelem niniejszego opracowania jest przeprowadzenie badań modułów sprężystości betonu klasy C60/75 oraz monitoring zmian temperaturowych w wybranych punktach sekcji S3.18P. System pomiaru temperatury służy także do wyznaczenia rzeczywistych wytrzymałości betonu w trakcie dojrzewania, sformułowania wskazówek dotyczących terminów demontażu deskowań lub weryfikacji terminów rozpoczęcia procesu sprężania konstrukcji.
-
ROZPRAWA DOKTORSKA. Rodzina elementów hybrydowo-mieszanych w 6-parametrowej teorii powłok, analiza geometrycznie nieliniowa powłok o funkcyjnej zmienności materiału wzdłuż grubości
PublicationW rozprawie opracowano rodzinę 4–węzłowych hybrydowo–mieszanych elementów skończonych w ramach nieliniowej 6–parametrowej teorii powłok, w której szóstym stopniem swobody jest obrót owinięcia. Elementy mieszane i częściowo mieszane sformułowano na podstawie odpowiednio podstawowego i autorsko zmodyfikowanego trójpolowego funkcjonału Hu–Washizu. W pracy zastosowano oryginalną interpolację niezależnych pól niesymetrycznych odkształceń...
-
Symulacje numeryczne jako wsparcie badania właściwości barier ochronnych
PublicationArtykuł przedstawia możliwości wykorzystania symulacji numerycznych do badań efektywności urządzeń bezpieczeństwa ruchu drogowego w aspekcie sposobów ich konfgurowania. Obecnie w celu dopuszczenia do stosowania bariery ochronne muszą przejść specjalistyczne testy zderzeniowe. Ze względu na wysoki koszt tych badań coraz częściej producenci barier oraz inne podmioty odpowiadające za urządzenia bezpieczeństwa ruchu drogowego (brd)...
-
Metoda samoorganizacji i podążania za liderem roju nieholonomicznych robotów mobilnych z wykorzystaniem wirtualnych elementów sprężysto-tłumiących
PublicationCelem pracy jest demonstracja metody samoorganizacji i podążania za liderem nieholonomicznego roju robotów mobilnych, opartej na wirtualnych, tłumionych, liniowych sprężynach łączących sąsiadujące roboty. Analizę metody sterowania poprzedza wyprowadzenie dynamiki dwukołowego robota oraz określenie zależności między wirtualnymi siłami a wejściami sterującymi robota w celu osiągnięcia stabilnej formacji roju. Analizowane są dwa przypadki...
-
Zastosowanie metod nieniszczących w diagnostyce nawierzchni drogowych w rejonie obiektów mostowych
PublicationW artykule przedstawiono możliwość wykorzystania metod nieniszczących w diagnostyce nawierzchni drogowych jako alternatywę do metod tradycyjnych w celu wyjaśnienia przyczyn powstawania zarysowań poprzecznych nawierzchni w sąsiedztwie obiektów mostowych. Wykorzystano dwie metody skanowania: laserowe w celu szczegółowej inwentaryzacji powierzchni nawierzchni oraz georadarowe (GPR) w celu inwentaryzacji struktury nawierzchni. W wyniku...
-
HYDROGEN PRODUCTION PERFORMANCE IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF NI3AL
PublicationThe main aim of the following paper is mathematical modelling for momentum, heat and mass transfer, which is accompanied by chemical surface reactions of the flow of the mixture helium and methanol. The thermocatalytic devices used for decomposition of hydrocarbons incorporate vertical microchannels coupling at the ends and heated to 500 oC at the walls. The results of the experiment were compared with CFD calculations to calibrate...
-
Wybrane zagadnienia modelowania Thermal-FSI określające przepływ płynu i wymianę ciepła na przykładzie benchmarkowego eksperymentu wymiennika ciepła z minikanałami
PublicationWybrane zagadnienia modelowania Thermal-FSI określające przepływ płynu i wymianę ciepła na przykładzie benchmarkowego eksperymentu wymiennika ciepła z minikanałami
-
Guided waves for nondestructive diagnostics of embedded waveguides
PublicationThe thesis concentrates on comprehensive theoretical, numerical and experimental analysis of guided wave propagation in bars embedded in concrete or mortar. The investigations are focused on a particular type of objects representing a laboratory model of a ground anchor. Complex description of wave propagation phenomena in partially embedded bars is given and its application in...
-
FEM analysis of composite materials failure in nonlinear six field shell theory
PublicationThe monography deals with the problem of failure initiation in thin laminated composites. Known techniques of laminate structures modelling are briefly characterised. Eventually, shell based approach is chosen for the purpose of the description of the composite structures behaviour, as it predicts their deformation and states of stress effectively in a global sense. The nonlinear six parameter shell theory (6p theory) with asymmetric...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublicationIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...
-
Właściwości termoizolacyjne kompozytu wapienno-cementowego z udziałem paździerzy konopnych=Thermal insulation properties of the lime-cement composite with hemp shives
PublicationPrzedstawiono wyniki badań kompozytów wykonanych na bazie wapna budowlanego, cementu i dolomitu - spoiwa wiążącego z udziałem paździerzy konopi. Określono ich podstawowe właściwości, tj.: gęstość objętościową, współczynnik przewodzenia ciepła oraz wytrzymałości na ściskanie. Otrzymane wyniki dowodzą, że wytworzone kompozyty wapienno-cementowe z udziałem paździerzy konopnych są lekkie i charakteryzują się niskim współczynnikiem...
-
Experimental and theoretical study on high-temperature creep of VT6 titanium alloy under multi-axial loading conditions
PublicationIn the framework of damage mechanics, we discuss a new mathematical model that describes the kinetics of the stress–strain state and damage accumulation during material degradation by the mechanism of long-term strength under complex multiaxial stress state. An experimental and theoretical technique is proposed for determination of material parameters and scalar constitutive functions for damaged media based on specially set experiments...
-
Characterization of Corrosion-Induced Fracture in Reinforced Concrete Beams Using Electrical Potential, Ultrasound and Low-Frequency Vibration
PublicationThe paper deals with the non-destructive experimental testing of the reinforced concrete beams under progressive corrosion. A series of experiments using electrical potential, ultrasound and low-frequency vibrations techniques are reported. Electrical potential and natural frequencies were used to characterise and monitor the corrosion process at its initial state. The P-wave velocity measurements were proved to be effective in...
-
A procedure for the identification of effective mechanical parameters of additively manufactured elements using integrated ultrasonic bulk and guided waves
PublicationThe subject of the current work was a simple but robust novel two-stage procedure for the non-destructive determination of effective elastic constants using ultrasonic wave propagation. First, ultrasonic bulk wave velocities measured on cubic samples were used to calculate most of the elements of the stiffness matrix. Secondly, the remaining elements were determined using the dispersion curves of elastic guided waves measured on...
-
Butyrylcholinesterase signal sequence self-aggregates and enhances amyloid fibril formation in vitro
PublicationAlzheimer’s disease (AD) pathogenesis has been attributed to extracellular aggregates of amyloid β (Aβ) plaques and neurofibrillary tangles in the human brain. It has been reported that butyrylcholinesterase (BChE) also accumulates in the brain Aβ plaques in AD. We have previously found that the BChE substitution in 5′UTR caused an in-frame N-terminal extension of 41 amino acids of the BChE signal peptide. The resultant variant...
-
Numerical analysis of lumbar spine injury during road safety barrier collision
PublicationPurpose: Enhancing road safety is a critical goal worldwide, necessitating the development of clear standards for road safety systems. This study focuses on lumbar spine (L-spine) compression injuries during collisions with concrete road safety barriers (RSBs). It aims to analyze internal forces during impact to understand L-spine injury biomechanics in such accidents. Methods: The research included a literature review, analyzing...
-
Mechanical response of human thoracic spine ligaments under quasi-static loading: An experimental study
PublicationPurpose This study aimed to investigate the geometrical and mechanical properties of human thoracic spine ligaments subjected to uniaxial quasi-static tensile test. Methods Four human thoracic spines, obtained through a body donation program, were utilized for the study. The anterior longitudinal ligament (ALL), posterior longitudinal ligament (PLL), capsular ligament (CL), ligamenta flava (LF), and the interspinous ligament and...
-
Pharmacomicrobiomics of cell-cycle specific anti-cancer drugs – is it a new perspective for personalized treatment of cancer patients?
PublicationIntestinal bacteria are equipped with an enzyme apparatus that is involved in the active biotrans-formation of xenobiotics, including drugs. Pharmacomicrobiomics, a new area of pharmacology, analyses interactions between bacteria and xenobiotics. However, there is another side to the coin. Pharmacotherapeutic agents can significantly modify the microbiota, which consequently affects their efficacy. In this review, we comprehensively...
-
Methodology of generation of CFD meshes and 4D shape reconstruction of coronary arteries from patient-specific dynamic CT
PublicationDue to the difficulties in retrieving both the time‑dependent shapes of the vessels and the generation of numerical meshes for such cases, most of the simulations of blood flow in the cardiac arteries use static geometry. The article describes a methodology for generating a sequence of time‑dependent 3D shapes based on images of different resolutions and qualities acquired from ECG‑gated coronary artery CT angiography. The precision...
-
Experimental and Numerical Investigations of the Effect of Curing Conditions on the Temperature Rise of Concrete
PublicationThis paper presents experimental and numerical studies investigating the impact of three curing conditions on temperature evolution in concrete cubes. The tests were performed on samples of the same volume (3.375 dm3) under different curing conditions: room temperature, insulation boxes, and adiabatic calorimeter. Various cements (Portland cement, Portland composite cement, and blast furnace slag cement) and aggregates (gravel...
-
On mechanics of piezocomposite shell structures
PublicationThis study presents an original and novel investigation into the mechanics of piezo-flexo-magneto-elastic nanocomposite doubly-curved shells (PFMDCSs) and the ability to detect the lower and higher levels of electro-magnetic fields. In this context, by utilizing the first-order shear deformation shell model, stresses and strains are acquired. By imposing Hamilton's principle and the von Kármán approach, the governing equations...
-
Novel Tools for Comprehensive Functional Analysis of LDLR (Low-Density Lipoprotein Receptor) Variants
PublicationFamilial hypercholesterolemia (FH) is an autosomal-dominant disorder caused mainly by substitutions in the low-density lipoprotein receptor (LDLR) gene, leading to an increased risk of premature cardiovascular diseases. Tremendous advances in sequencing techniques have resulted in the discovery of more than 3000 variants of the LDLR gene, but not all of them are clinically relevant. Therefore, functional studies of selected variants...
-
Nanoparticle Tracking Analysis of Urinary Extracellular Vesicle Proteins as a New Challenge in Laboratory Medicine
PublicationUrinary extracellular vesicle (uEV) proteins may be used as specific markers of kidney damage in various pathophysiological conditions. The nanoparticle-tracking analysis (NTA) appears to be the most useful method for the analysis of uEVs due to its ability to analyze particles below 300 nm. The NTA method has been used to measure the size and concentration of uEVs and also allows for a deeper analysis of uEVs based on their protein...
-
M-integral for finite anti-plane shear of a nonlinear elastic matrix with rigid inclusions
PublicationThe path-independent M-integral plays an important role in analysis of solids with inhomogeneities. However, the available applications are almost limited to linear-elastic or physically non-linear power law type materials under the assumption of infinitesimal strains. In this paper we formulate the M-integral for a class of hyperelastic solids undergoing finite anti-plane shear deformation. As an application we consider the problem...
-
Damage of a post-tensioned concrete bridge – Unwanted cracks of the girders
PublicationThe cracking of a post-tensioned T-beam superstructure, which was built using the incremental launching method, is analyzed in the paper. The problem is studied in detail, as specific damage was observed in the form of longitudinal cracks, especially in the mid-height zone of the girder at the interface of two assembly sections. The paper is a case study. A detailed inspection is done and non-destructive testing results of the...
-
Anisotropy and compaction gradient assessment on rammed earth specimens through sonic tomography approach
PublicationRammed earth is a traditional construction technique that has recently gained attention because of its benefits from an ecological perspective. The conservation of the existing valuable cultural heritage sites and the quality control of new constructions built with this material require the development and application of practical inspection techniques. This paper explores the application of sonic tests and sonic tomography as...
-
Discrete element method modelling of elastic wave propagation in a meso-scale model of concrete
PublicationThis paper deals with the accurate modelling of ultrasonic wave propagation in concrete at the mesoscopic level. This was achieved through the development of a discrete element method (DEM) model capable of simulating elastic wave signals comparable to those measured experimentally. The main objective of the work was to propose a novel methodology for constructing a meso-scale model of concrete dedicated to the analysis of elastic...
-
Numerical Analysis of Mice Carotid Arteries’ Response Emphasizing the Importance of Material Law Constants’ Validation
PublicationIn this paper, a detailed validation of the passive material properties of mice carotid arteries and constants of the Fung and Holzapfel hyperelastic material laws is conducted by means of static nonlinear FEM analyses. The response of the carotid arteries in an inflation test is studied here for the following mouse models: wild-type, mdx, sgcd−/−, Eln+/+, Eln+/−, Fbln5+/+, and Fbln5−/−. All FEM computations are conducted on models...
-
In Vitro and In Vivo Imaging-Based Evaluation of Doxorubicin Anticancer Treatment in Combination with the Herbal Medicine Black Cohosh
PublicationAs a substitution for hormone replacement therapy, many breast cancer patients use black cohosh (BC) extracts in combination with doxorubicin (DOX)-based chemotherapy. In this study, we evaluated the viability and survival of BC- and DOX-treated MCF-7 cells. A preclinical model of MCF-7 xenografts was used to determine the influence of BC and DOX administration on tumor growth and metabolism. The number of apoptotic cells after...
-
Numerical modelling of different airbag folding patterns and their influence on occupant responses in frontal vehicle impact
PublicationThis paper presented a procedure for airbag folding for the application in occupant safety studies and analysed the influence of different airbag folding patterns on the occupant severity in frontal impact. Airbags were folded in two patterns: zig-zag and top-roll, using two folding techniques: Initial Metric Method and Explicit Folding. The explicit folding was found to be more expensive in terms of preparation time. However,...
-
Badania mostu III Tysiąclecia im. Jana Pawła II w ciągu Trasy Sucharskiego w Gdańsku
PublicationW pracy przedstawiono zakres oraz wyniki badań podczas próbnego obciążenia drogowego mostu podwieszonego przez rzekę Martwą Wisłę w Gdańsku. Scharakteryzowano metodę pomiarów (aparaturę pomiarową), omówiono wyniki badań statycznych i dynamicznych oraz przedstawiono podsumowanie i wnioski z badań.
-
Der betonschutz vor der Wirkung der aggressiven Umgebung
PublicationPraca dotyczy zabezpieczenia powierzchni betonowych przed wnikaniem oleju, wody, roztworów soli. W pracy przedstawiono podstawy teoretyczne transportu cieczy, ruch cieczy w kapilarach.
-
On the paradox of torsional buckling of thin-walled I columns
PublicationAnaliza wyboczenia skrętnego pręta cienkościennego o dwuteowym przekroju poprzecznym ze zmienną, w pewnych granicach, szerokością półek wykazała, że siła krytyczna wyboczenia skrętnego może przekraczać granice wyznaczone przez siły odpowiadające prętom o stałych ekstremalnych szerokościach półek. Ten paradoksalny wynik uzyskano w ramach teorii prętów cienkościennch o przekroju nieodkształcalnym. Ponadto wykazano, że punkt bifurkacji...
-
Simple model of rain wind induced vibrations of stayed cables.
PublicationAnalizowano prosty, liniowy model drgań kabli mostów wantowych pod obciążeniem wiatrem i deszczem. Zakłada się, iż częstotliwość ruchu górnej kropli po powierzchni kabla i częstotliwość kabla są równe oraz iż amplituda ruchu kropli dla danej prędkości wiatru są stałe. Otrzymane rezultaty są porównane z istniejącymi w literaturze wynikami badań eksperymentalnych. Podaje się analityczne związki służące do oszacowania tłumienia...
-
Modelowanie drgań kabli wywołanych działaniem wiatru i deszczu
PublicationW referacie zaproponowano prosty, liniowy model drgań kabli mostów wantowych obciążonych wiatrem i deszczem. Założono, iż częstotliwość ruchu górnej kropli po powierzchni kabla i częstotliwość kabla są równe oraz iż amplituda ruchu kropli dla danej prędkości wiatru są stałe. Otrzymane rezultaty porównano z istniejącymi w literaturze wynikami badań eksperymentalnych. Podano analityczne związki służące do oszacowania tłumienia aerodynamicznego...
-
Eigenschaften der selbstverdichtenden Betone mit zerstreuter Bewehrung.
PublicationReferat dotyczy badania wpływu różnych domieszek upłynniających i dodatków(mikrowypełniaczy oraz włókna stalowego i polipropylenowego) na właściwości mieszanki betonowej samozagęszczalnej jaki na parametry betonu stwardniałego. Badania prowadzono w dwóch etapach. W etapie I opracowano receptury kilku mieszanek samozagęszczalnych bez dodatku włókien. W etapie II na mieszankach wytypowanych w etapie I po dodaniu różnych ilości...
-
Flatter jednoprzęsłowej wiszącej kładki dla pieszych
PublicationPrzedstawiono analizę aerodynamiczną stateczności wybranego typu wiszącej kładki dla pieszych z uwzględnieniem zjawiska flatteru i dywergencji.
-
Crack identification in cantilever beam using wavelets
PublicationPrzedstawiono metodę identyfikacji zniszczeń przy użyciu transformacji falkowej. Rozpatrzono przykład belki wspornikowej. Pokazano, że transformacja falkowa wykrywa miejsce zniszczenia.
-
Ausgewahlten Warme und Feuchtigkeits probleme von Industriefussboden.
PublicationWiele obiektów budowlanych, jak hale przemysłowe, magazyny, warsztaty, hangary, sklepy, supermarkety itp. wyposażonych jest w posadzkę ułożoną bezpośrednio na gruncie. Rola, jaką pełni najniżej położona w tych obiektach posadzka podlega takim samym prawom fizyki budowli jak i mechaniki, tak jak każdy inny znaczący element konstrukcyjny obiektu. Oczywiście nie można jej rozpatrywać w aspekcie elementu wydzielonego z pewnej całości,...
-
Kompozyty cementowo-popiołowe modyfikowane dodatkiem włókien stalowych.
PublicationPraca dotyczy określenia wpływu niewielkiej ilości włókien stalowych na właściwości techniczne kompozytów popiołowo-cementowych. W opracowaniu przedstawiono wyniki badań kompozytów w zakresie zmian wytrzymałości na rozciąganie przy zginaniu, zmian wytrzymałości na rozciąganie przy rozłupywaniu, zmian wytrzymałości na ściskanie.
-
Zagadnienia termiczno-wytrzymałościowe przy projektowaniu i eksploatacji posadzek na gruncie.
PublicationNa podstawie wyników obliczeń przeprowadzonych dla przykładów można stwierdzić, że nawet mała różnica temperatury na grubości podkładu może doprowadzić do sporych deformacji oraz zarysowań wskutek około 5-krotnego przyrostu wielkości naprężeń wewnętrznych. Przedstawiono obliczenia cieplne posadzek na gruncie, zagadnienia wytrzymałościowe, wybrane zagadnienia z wykonawstwa.
-
Podłogi na gruncie.
PublicationRola podłogi na gruncie będącej jednym z bardziej odpowiedzialnych ustrojów każdego obiektu budowlanego jest niejednokrotnie lekceważona, a nawet pomijana już na etapie jego projektowania.W artykule przedstawiono wymagania stawiane podłogom, zagadnienia wytrzymałościowe i zasady konstruowania podłóg na podłożu gruntowym oraz obliczenia cieplne podłóg na gruncie.
-
Modelowanie testów dynamicznych skokiem z progu wykonanych na moście wantowym w ciągu ulicy Sucharskiego w Gdańsku.
PublicationPrzedstawiono numeryczne symulacje testu dynamicznego przeprowadzonego na podwieszonym moście w ciągu Trasy Sucharskiego w Gdańsku. Drgania mostu wywołane były skokiem przedniej osi samochodu TATRA z progu o wysokości 7 cm. Samochód modelowano jako układ o dwóch stopniach swobody dla którego parametry określono na podstawie pomiarów dwoma akcelerometrami umiejscowionymi na przedniej masce i osi samochodu. przestrzenny model...
-
3-węzłowy płaski element powłokowy z 6 stopniem swobody
PublicationPraca dotyczy zastosowania płaskiego trójkątnego (trójwęzłowego) elementu powłokowego w analizie powłok w zakresie nieliniowym geometrycznie. Użyte elementy otrzymano poprzez połączenie elementów wyprowadzonych dla stanu membranowego i zgięciowego.
-
Mechanical Properties of 3D Printed Parts and Their Injection Molded Alternatives Subjected to Environmental Aging
PublicationAdditive manufacturing is the technology used in medical, industrial, or lifestyle applications. The scientific literature include works reporting various manufacturing parameters’ influence on changes in additive manufacturing components’ mechanical behavior, especially with fused filament fabrication (FFF). The changes in mechanical strength and toughness of FFF compared to injection molding parts were studied. In the study,...
-
On implementation of fibrous connective tissues’ damage in Abaqus software
PublicationConnective fibrous tissues, such as tendons and ligaments, in humans and animals exhibit hyperelastic behaviour. The constitution of the material of these tissues is anisotropic due to the presence of the collagen fibres, where one family of fibres is the typical case. Traumatic events and/or aging may sometimes lead to the damage of the tissue. The study of motion of affected joints or limbs is usually not permitted in vivo. This...
-
A model of damaged media used for describing the process of non-stationary creep and long-term strength of polycrystalline structural alloys
PublicationThe main laws of the processes of creep and long-term strength of polycrystalline structural alloys are considered. From the viewpoint of continuum damaged media (CDM), a mathematical model is developed that describes the processes of viscoplastic deformation and damage accumulation under creep. The problem of determining material parameters and scalar functions of the developed constitutive relations based on the results of specially...
-
CONCRETE MIX DESIGN USING ABRAMS AND BOLOMEY METHODS
PublicationOne way to reduce the consumption of cement is to optimize its use. Many known methods of concrete design, based on the Abrams law and the Bolomey method. Therefore, the authors chose those methods for analysis. The concrete composition with the assumed strength class, calculated by any method differs significantly. This applies especially to the cement content, as its content in the composition of concrete varies from 20 to 50%....
-
Sustainable utilization of copper post-flotation waste in cement composites
PublicationThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
Mixed 4-node shell element with assumed strain and stress in 6-parameter theory
PublicationWe propose a mixed hybrid 4-node shell elements based on Hu-Washizu principle. Apart from displacements both strains and stress fields are treated as independent fields. The element is derived in the framework of a general nonlinear 6-field shell theory with drilling rotation which is dedicated to the analysis of multifold irregular shells with intersections. The novelty of the presented results stems from the fact that the measures...
-
Protein overproduction alters exosome secretion in Chinese hamster ovary cells
PublicationDespite the abundance of available cell lines, nearly 70% of all recombinant therapeutic proteins today are produced in Chi-nese hamster ovary (CHO) cells. The impact of protein overproduction on the secretion of exosomes by CHO cells has been investigated here. Increased secretion of extracellular vesicles (EVs) by protein overexpressing CHO cells was demonstrated with protein content assay, nanoparticle tracking analysis, and...
-
On rotary inertia of microstuctured beams and variations thereof
PublicationWe discuss the classic rotary inertia notion and extend it for microstructured beams introducing new microinertia parameters as an additional dynamic response to microstructure changes. Slender structures made of beam- or platelet-lattice metamaterials may exhibit not only large translations and rotations but also general deformations of inner structure. Here we considered a few examples of beam-like structures and derive their...
-
Can we really solve an arch stability problem?
PublicationWe bring attention to the problem of solving nonlinear boundary-value problems for elastic structures such as arches and shells. Here we discuss a classical problem of a shear-deformable arch postbuckling. Considering a postbuckling behaviour of a circular arch we discuss the possibility to find numerically a solution for highly nonlinear regimes. The main attention is paid to the problem of determination of all solutions. The...
-
Thermo-resonance analysis of an excited graphene sheet using a new approach
PublicationForced vibration of graphene nanoplate based on a refined plate theory in conjunction with higher-order nonlocal strain gradient theory in the thermal environment has been investigated. Regarding the higher-order nonlocal strain gradient theory, both stress nonlocality and size-dependent effects are taken into account, so the equilibrium equations which are governing on the graphene sheet have been formulated by the theory....
-
THE METHOD OF MEASURING THE MEMBRANE COVER GEOMETRY USING LASER SCANNING AND SYNCHRONOUS PHOTOGRAMMETRY
PublicationThe authors present the experience and results of field studies carried out at the technical acceptance of Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland). An unusual design of covering made in the form of “Sheerfill I” technical fabric membrane required spanned in the form of sails, required the use of terrestrial laser scanning. Such approach allowed for the fast and accurate record of the surface of individual panels...
-
Experimental and numerical analysis of wave propagation in ground anchors
PublicationThe article focuses on wave propagation phenomenon in ground anchors. The main aim of the investigation is the non-destructive diagnostics and the assessment of the state of ground anchors, using the guided wave propagation method. Laboratory models of anchors with different lengths of the anchor body were tested and voltage signals of propagating waves were registered at several locations. For all tested specimens corresponding...
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublicationThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Recent Achievements in Constitutive Equations of Laminates and Functionally Graded Structures Formulated in the Resultant Nonlinear Shell Theory
PublicationThe development of constitutive equations formulated in the resultant nonlinear shell theory is presented. The specific features of the present shell theory are drilling rotation naturally included in the formulation and asymmetric measures of strains and stress resultants. The special attention in the chapter is given to recent achievements: progressive failure analysis of laminated shells and elastoplastic constitutive relation...
-
Detection of debonding in adhesive joints using Lamb wave propagation
PublicationAdhesively bonded joints are widely used in many branches of industry. Mechanical degradation of this type of connections does not have significant symptoms that can be noticed during visual assessment, so non-destructive testing becomes a very important issue. The paper deals with experimental investigations of adhesively bonded steel plates with different defects. Five samples (an intact one and four with damages in the form...
-
Ultrasonic Tomography of Brick Columns Based on FEM Calculations
PublicationUltrasonic tomography is one of the most developed method of non-destructive testing. Despite being used mainly in medicine, it is becoming more and more popular as a method for monitoring of structural elements. It allows to examine the internal structure and technical condition of the tested element. This paper investigates the influence of crosssectional geometry on an obtained tomographic image. Wave propagation signals were...
-
Dynamic Response of the Suspended on a Single Cable Footbridge
PublicationThe article presents numerical simulations, dynamic in situ load tests and a structural health monitoring (SHM) system installed in a suspended on a single cable footbridge. Numerical simulations performed prior to construction indicated the possibility of structural dynamics problems, finally confirmed in the course of dynamic test loading. In the dynamic load course the bridge deck developed vibrations displaying accelerations...
-
Innovative Research Into Road Restraint Systems
PublicationKey to understanding the needs and building road infrastructure management tools to prevent and mitigate run-off-road accidents is to identify hazards and their sources which are a result of wrong design, construction, installation and maintenance of road restraint systems [1]. Building such tools requires advanced studies with field tests, simulations and models to demonstrate the effects of selected parameters on road user safety...
-
FEM simulation of laminate failure in the three point bending
PublicationThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Modelling of elastic wave propagation in a bolted joint using a thin layer of shell elements
PublicationThere are many mathematical models describing the propagation of elastic waves through the imperfect boundary of two media. They were successfully applied to modelling of high frequency bulk waves and their interaction with local defects. On the other hand, the existing literature models of bolted connections ignore the aspect of imperfect connection between elements. Therefore, this paper presents the concept of application of...
-
Mixed 4-node shell element with assumed strain and stress in 6-parameter theory
PublicationWe propose a mixed hybrid 4-node shell elements based on Hu-Washizu principle. Apart from displacements both strains and stress fields are treated as independent fields. The element is derived in the framework of a general nonlinear 6-field shell theory with drilling rotation which is dedicated to the analysis of multifold irregular shells with intersections. The novelty of the presented results stems from the fact that the measures...
-
Wybrane metody wzmacniania ceglanych obiektów zabytkowych.
PublicationWzmacnianie konstrukcji murowych stanowi jedno z najbardziej istotnych przedsięwzięć w dziedzinie utrwalania zabytków. Licznie prowadzone badania potwierdzają, że prawidłowo zaplanowane oraz wykonane wzmocnie nie uszkodzonej konstrukcji murowej obiektu zabytkowego pozwala na jego stabilizację i właściwe funkcjonowanie. W artykule zaprezentowano wybrane metody wzmacniania ceglanych konstrukcji obiektów zabytkowych. Przedstawiono...
-
The validation process of truss model with joint eccentricities
PublicationNowadays, due to the technological reasons in modern lightweight steel trusses, fabricated from cold-formed sections, positive eccentricities appear in the truss nodes, to induce additional forces truss chords. In order to account for the real load-carrying capacity of truss node area the steel structure research was conducted in scale 1:1. As a result of experimental research, the forms of deformation and strains of the walls...
-
Failure characterisation of sandwich beams using integrated acoustic emission and digital image correlation techniques
PublicationThe paper presents the experimental study of the failure behaviour of sandwich beams subjected to bending. The samples examined are sandwich beams made of polyethylene terephthalate foam core and glass fibre-reinforced polymer laminate face sheets. In a series of experiments, it has been proposed to integrate diagnostic techniques with acoustic emission and digital image correlation to accurately track the cracking process on the...
-
Technique for reducing erosion in large-scale circulating fluidized bed units
PublicationThis paper presents a methodology, implemented for a real industrial-scale circulating fluidized bed boiler, to mitigate the risk of heating surfaces exposed to an intensive particle erosion process. For this purpose, a machine learning algorithm was developed to support the boiler reliability management process. Having a tool that can help mitigate the risk of uncontrolled power unit failure without expensive and technically complex...