Filtry
wszystkich: 2336
wybranych: 2248
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: pv modules efficiency
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublikacjaConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
-
Design Analysis of Micro Gas Turbines in Closed Cycles
PublikacjaThe problems faced by designers of micro-turbines are connected with a very small volume flow rate of working media which leads to small blades’ height and high rotor speed. In the case of gas turbines this limitation can be overcome by the application of a closed cycle with very low pressure at the compressor inlet (lower than atmospheric pressure). In this way we may apply a micro gas turbine unit of accepted efficiency to work...
-
Równolegle przebiegające procesy separacji pianowej jonów Al(III), Cu(II) i Zn(II) z roztworów ich mieszanin
PublikacjaMetody flotacji jonowej i precypitacyjnej należą do procesów separacji pianowej, wykorzystujących zdolność selektywnej adsorpcji niektórych składników roztworu na powierzchni międzyfazowej gaz – ciecz. Do zalet separacji pianowej zalicza się m.in. niewysokie koszty inwestycyjne i eksploatacyjne oraz wysoką skuteczność w obróbce roztworów rozcieńczonych. Celem pracy jest ocena wpływu kluczowych parametrów na wydajność i przebieg...
-
EMI attenuation in a DC-DC buck converter using GaN HEMT
PublikacjaA dc-dc buck converter using gallium nitride (GaN) high electron mobility transistors (HEMT) is experimentally investigated at the discontinuous current mode (DCM) and at the triangular current mode (TCM) operation. The paper objective is to specify the power conversion efficiency and attenuation of common mode (CM) and differential mode (DM) noise voltage, measured at the line impedance stabilization network (LISN) for compared...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublikacjaThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
Solvent-Free Synthesis of Phosphonic Graphene Derivative and Its Application in Mercury Ions Adsorption
PublikacjaFunctionalized graphene was efficiently prepared through ball-milling of graphite in the presence of dry ice. In this way, oxygen functional groups were introduced into material. The material was further chemically functionalized to produce graphene derivative with phosphonic groups. The obtained materials were characterized by spectroscopic and microscopic methods, along with thermogravimetric analysis. The newly developed material...
-
Integrated spatial and energy planning – importance of a problem for contemporary architects and urban planners with focus on environmental factors
PublikacjaAlong with respecting basic sustainable development goals, planners will also be obliged to meet more stringent provisions related to energy efficiency in the coming years. In Poland, a crucial year will be 2021, when the EU directive on the energy efficiency of buildings comes into force. In this matter, not only the characteristics of individual objects are of great importance, but their whole complexes and the overall approach...
-
Microwave treatment in waste rubber recycling – recent advances and limitations
PublikacjaEnvironmentally-friendly microwave heating is increasingly used in polymer chemistry and technology. The selectivity and highly efficiency in the heat transfer present a huge advantage in systems based on recycling, improving their productivity and economic competitiveness. In case of the industrial recycling of waste rubbers, especially end-of-life tires, microwave-induced devulcanization and pyrolysis are nowadays considered...
-
Task Scheduling – Review of Algorithms and Analysis of Potential Use in a Biological Wastewater Treatment Plant
PublikacjaThe idea of task scheduling is to increase the efficiency of a system by minimising wasted time, evenly loading machines, or maximising the throughput of machines. Moreover, the use of appropriate scheduling algorithms often leads to a reduction in the energy costs of the process. Task scheduling problems are found in a variety of industrial areas, and their scale changes significantly depending on the problem. This review shows...
-
Experimental and numerical investigation on shell and coil storage unit with biodegradable PCM for modular thermal battery applications
PublikacjaThermal energy storage (TES) in automotive applications is currently growing in importance. TES can visibly reduce primary energy consumptions, decrease CO2 emission, and improve thermal comfort in electric as well as hybrid vehicles. However, to meet the new ambitious target (15% reduction of CO2 emissions in the new cars until 2025) it is required to use plug-in electric vehicles. For this reason, this paper focuses on the optimization...
-
Bridging challenges of clinical decision support systems with a semantic approach. A case study on breast cancer
PublikacjaThe integration of Clinical Decision Support Systems (CDSS) in nowadays clinical environments has not been fully achieved yet. Although numerous approaches and technologies have been proposed since 1960, there are still open gaps that need to be bridged. In this work we present advances from the established state of the art, overcoming some of the most notorious reported difficulties in: (i) automating CDSS, (ii) clinical workflow...
-
Comparative Analysis of Unmanned Aerial Vehicles Used in Photogrammetric Surveys
PublikacjaThere are many manufacturers on the market offering various types of Unmanned Aerial Vehicles (UAV). The multitude of drones available on the market means that the choice of a UAV for a specific application appears to be a decision problem to be solved. The aim of this article is a comparative analysis of drones used in photogrammetric surveys. The criteria for evaluating the UAVs were: availability and product support, payload...
-
Modular Approach for Modelling Warming Up Process in Water Installations with Flow-Regulating Elements
PublikacjaThe paper presents a new method for modelling the warming up process of a water system with elements regulating the flow in a stochastic manner. The paper presents the basic equations describing the work of typical elements which the water installation is composed of. In the proposed method, a new computational algorithm was used in the form of an iterative procedure enabling the use of boundary conditions that can be stochastically...
-
Kształtowanie poziomu wskaźników sprawności działania przez przedsiębiorstwa z sektora MSP w zależności od osiąganej rentowności aktywów
PublikacjaW artykule przedstawiono różnice w kształtowaniu poziomów wskaźników z obszaru sprawności działania pomiędzy przedsiębiorstwami z sektora MSP w zależności od osiąganej przez nie rentowności aktywów. W trakcie przeprowadzonych badań uwzględniono 34.820 sprawozdania finansowe przedsiębiorstw, prowadzących działalność gospodarczą w 22 różnych działach gospodarki narodowej. Do potwierdzenia zróżnicowania sprawności działania przedsiębiorstw...
-
Organic Rankine cycle as bottoming cycle to a combined Brayton and Clausius - Rankine cycle
PublikacjaA preliminary evaluation has been made of a possibility of bottoming of a conventional Brayton cycle cooperating with the CHP power plant with the organic Rankine cycle installation. Such solution contributes to the possibility of annual operation of that power plant, except of operation only in periods when there is a demand for the heat. Additional benefit would be the fact that an optimized backpressure steam cycle has the advantage...
-
Molecularly imprinted polymers applied in capillary electrochromatography and electrophoresis techniques
PublikacjaMolecularly imprinted polymers (MIPs) are synthetic materials with predetermined selectivity for a particular analyte or group of structure-linked chemicals which make them an ideal separation component. The process of developing and applying new types of MIPs in the field of environmental analytical chemistry has been broadly discussedi n many scientific studies in recent years. The use of new types of MIP sorbents as unique sorption...
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublikacjaThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
The share of investments in gold and oil using the example of selected European stock exchanges– A comparative analysis
PublikacjaIn this article, optimal investment portfolios with minimal risk and maximum efficiency were calculated. The portfolios were designated for ten selected European stock exchanges, based on the listings of the twenty largest companies in each of those markets. All calculations were made based on company shares only, company shares and investments in gold, shares of companies and investments in crude oil as well as shares of companies...
-
Metody redukcji zróżnicowania materiałów wejściowych w warunkach wysokiej różnorodności produktów gotowych
PublikacjaArtykuł opisuje zagadnienie związane z negatywnym wpływem wysokiego zróżnicowania materiałów wejściowych w procesach produkcyjnych o wysokiej różnorodności produktów gotowych. W pierwszej części pracy opisane zostało oddziaływanie zróżnicowania materiału na podstawowe mierniki skuteczności procesu produkcyjnego z uwzględnieniem cen zakupu materiałów, kosztów utrzymania zapasów, jakości produktu oraz wydajności maszyn i urządzeń....
-
A new technology of crude vegetable oil degumming with rhamnolipid solutions
PublikacjaA new technology of crude vegetable oil degumming is described. It is based on rhamnolipid biocomplex solution application for phosphatides removal. The rhamnolipid biocomplex produced by Pseudomonas sp. PS-17 was used as biosurfactant. Rapeseed oil was used in all experiments. First, it was degummed with H2SO4 in order to remove all phosphatides and then 1% (w/w) of granular soybean lecithin was added. Model oil was treated with...
-
Photocatalytic activity of nitrogen doped TiO2 nanotubes prepared by anodic oxidation: The effect of applied voltage, anodization time and amount of nitrogen dopant
PublikacjaNitrogen doped TiO2 nanotube arrays were prepared by anodizing Ti foils in an organic electrolyte containing specified amounts of urea as nitrogen precursor. The photocatalytic activity of the samples was evaluated by analyzing the degradation kinetics of phenol in water. The influence of tubes’ length, tubes’ surface morphology and amount of nitrogen in the TiO2 lattice on hydroxyl radical formation efficiency, photocatalytic...
-
Sewage gardens - constructed wetlands for single family households
PublikacjaDuring the last 30 years the increase of interest in low-cost decentralized and small wastewater treatment plants (WWTP) is observed in Europe. For this purpose sand filters, stabilization ponds, mini reactors with activated sludge, trickling filters and treatment wetlands are used. Among the listed facilities treatment wetlands (TWs) offer effective and reliable treatment efficiency, being at the same time low-cost and simple...
-
Soft – Partial Frequency Reuse Method for LTE-A
PublikacjaIn the paper a novel SPFR frequency reuse method is proposed which can be used for improvement of physical resources utilization efficiency in LTE-A. The proposed method combines both SFR and PFR giving the possibility of more flexible use of frequency band in different regions of a cell. First, a short study on the problem of frequency reuse in cells is discussed including bibliography overview....
-
Modification of Ground Tire Rubber—Promising Approach for Development of Green Composites
PublikacjaGround tire rubber (GTR) was mechano-chemically modified using a road bitumen 100/150 and two types of organic peroxides: di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB) and dicumyl peroxide (DCP). The impact of used additives on reactive sintering efficiency and physico-mechanical properties of modified GTR was investigated using oscillating disc rheometer measurements, followed by tensile tests and swelling behavior studies....
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublikacjaThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
Comparison of the Effectiveness of Health Systems in The European Countries-Two-Stage DEA Model
PublikacjaThis article compares the efficiency of health systems in selected European countries using two-stage data envelopment analysis (DEA), based on data from the EUROSTAT database. In the first step, DEA efficiency scores were calculated for health care systems and, subsequently, the external variables describing lifestyle were used to calculate the truncated regression. Health care resources (physicians, nurses, hospital beds, financial...
-
Stirling engines - the state of technology development and computational models
PublikacjaStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Przyszłość fotowoltaiki - instalacje zintegrowane z budynkiem (BIPV). Cz. 2
PublikacjaSystemy fotowoltaiczne zintegrowane z budynkiem (BIPV) są to integralne elementy konstrukcyjne budynku, służące do zasilania w energię elektryczną. Bezpośrednie lub rozproszone światło promieniowania słonecznego, oświetlając ogniwa słoneczne, wchodzące w skład instalacji, indukuje efekt fotowoltaiczny, generując stałe napięcie elektryczne. Napięcie to może być wykorzystane bezpośrednio do zasilania urządzeń, ładowania akumulatorów...
-
Moduł Warsztaty - narzędzie w procesie edukacji na uczelni wyższej
PublikacjaObecnie istnieje bardzo szeroka gama narzędzi informatycznych, które wspierają proces edukacji przy wykorzystaniu internetu na uczelniach wyższych. Wśród nieodpłatnych narzędzi powszechnie znana jest platforma Moodle. W artykule zaprezentowano jeden z jej modułów – Warsztaty. Przedstawiono jego funkcjonalność. Opisano jego zalety i wady w nauczaniu łączącym techniki online i tradycyjne na uczelni wyższej (blended-learning). W artykule...
-
Effect of synthesis method parameters on properties and photoelectrocatalytic activity under solar irradiation of TiO2 nanotubes decorated with CdS quantum dots
PublikacjaThe growing research interest on photoelectrocatalysis has encouraged the search for new materials with high activity and the development of methods for their synthesis. The successive ionic layer adsorption and reaction (SILAR) method is an effective way to synthesize materials with photoelectrocatalytic (PEC) properties that are active under visible radiation. Therefore, studies on the impact of the parameters of the SILAR method...
-
Adversarial attack algorithm for traffic sign recognition
PublikacjaDeep learning suffers from the threat of adversarial attacks, and its defense methods have become a research hotspot. In all applications of deep learning, intelligent driving is an important and promising one, facing serious threat of adversarial attack in the meanwhile. To address the adversarial attack, this paper takes the traffic sign recognition as a typical object, for it is the core function of intelligent driving. Considering...
-
The concept of stream and system reliability on the example of the bakery industry
PublikacjaThis article presents a new concept of technological system reliability based on the analysis of the relationship of associations of elements of energy streams, matter, information, time and finance. The method of stream specification and the method of determining the reliability values of significant and supporting relationships are given. Relevant relationships between elements of system streams were defined as having one-time...
-
Evaluation of propagation parameters of open guiding structures with the use of complex root finding algorithms
PublikacjaAn efficient complex root tracing algorithm is utilized for the investigation of electromagnetic wave propagation in open guiding structures. The dispersion characteristics of propagated and leaky waves are calculated for a couple of chosen waveguides. The efficiency of the root tracing algorithm is discuses and compared to a global root finding algorithm.
-
Wetting properties of biosurfactant (rhamnolipid) with synthetic surfactants mixtures in the context of soil remediation
PublikacjaWetting properties of synthetic surfactant Rokanol NL6, biosurfactant JBR 425 and their mixture have been investigated.The results show that synthetic surfactant addition worsens physicochemical properties of pure biosurfactant but exhibits much higher oil removal efficiency than biosurfactant does.
-
Deposition and Electrical and Structural Properties of La0.6Sr0.4CoO3 Thin Films for Application in High-Temperature Electrochemical Cells
PublikacjaLow-temperature deposition of electroceramic thin films allows the construction of new devices and their integration with existing large-scale fabrication methods. Developing a suitable low-cost deposition method is important to further advance the development of microdevices. In this work, we deposited a 1-lm-thick La0.6Sr0.4CoO3d (LSC) perovskite with high electrical conductivity on sapphire substrates at 400C and analyzed its...
-
Diagnostic system of wheeled tractors detecting four defect's categories
PublikacjaIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
Reception of Terrestrial DAB+ and FM Radio with a Mobile Device: A Subjective Quality Evaluation
PublikacjaNowadays, terrestrial broadcasting enables to receive content anytime and everywhere. People can obtain information both with a portable or desktop receiver, which include pocket-sized devices as well as high-end Hi-Fi equipment, not to mention car audio systems. Numerous manufacturers include FM-compatible chipsets in a variety of user equipment (UE), including mobile phones. However, digital radio signal processing modules, such...
-
THREE-LEVEL F-TYPE INVERTER
PublikacjaGiven the recent available IGBT switch modules up to 6.5 kV, 1200 A rating, the prospect of the diode-free variant topology of the three-level neutral-point-clamped (3-level, T-type) inverter in certain medium voltage applications is bright; due to its small part count and low conduction losses compared to the diode-clamped NPC inverter. However, within this voltage range, the input dc voltage rating of 50% of the switches per...
-
Optimization-based antenna miniaturization using adaptively-adjusted penalty factors
PublikacjaThe continuing trend for miniaturization of electronic devices necessitates size reduction of the comprising components and circuitry. Specifically, integrated circuit-antenna modules therein require compact radiators in applications such as 5G communications, implantable and on-body devices, or internet of things (IoT). The conflict between the demands for compact size and elec-trical and field performance can be mitigated by...
-
Smart Virtual Product Development: Manufacturing Capability Analysis and Process Planning Module
PublikacjaSmart Virtual Product Development (SVPD) system provides effective use of information, knowledge, and experience in industry during the process of product development in Industry 4.0 scenario. This system comprises of three primary modules, each of which has been developed to cater to a need for digital knowledge capture for smart manufacturing in the areas of product design, production planning, and inspection planning. Manufacturing...
-
An Efficient Simulation Method of Massive MIMO Antenna Arrays used in 5G Mobile Phones
PublikacjaThis paper deals with a model-order reduction method, applied to speed-up the simulations of MIMO antenna arrays, performed by means of finite element method. The obtained results of the numerical tests show that the described technique is reliable and considerably increases the efficiency of the standard finite element method.
-
Pollutants removal effectiveness in hydrophyte filters with sequential vertical and horizontal flow
PublikacjaThe object of investigations was the constructed wetland in Wiedersberg in Saxonia in Germany supplied with domestic sewage from 145 inhabitants. The biological part was composed of sequential reed beds with vertical and horizontal flow of sewage. It in one of new solutions, because up till now configuration with vertical bed situated at front of biological part of treatment was applied.The evaluation of object performance was...
-
Markowitz’s portfolio theory – optimal length of estimation window for gold and the biggests companies on the Warsaw Stock Exchange
PublikacjaThe following article is dedicated to the construction of an investment portfolio consisting of 3 investments from the Polish capital market found in the WIG20 index and from investment in gold. The purpose of the study was to determine the optimal length of the estimation window for building a portfolio with minimal risk and maximum efficiency. The length of the estimation window was also assessed in terms of the rate of return...
-
Protection in elastic optical networks
PublikacjaIn this article, we analyze gains resulting from the use of EON architectures with special focus on transportation of cloud-ready and content-oriented traffic in the context of network resilience. EONs are a promising approach for future optical transport networks and, apart from improving the network spectral efficiency, bring such new capabilities as squeezed protection, which reduces resource requirements in failure scenarios....
-
Pharmaceutical and forensic drug applications of chiral supercritical fluid chromatography
PublikacjaTHE SUPERCRITICAL FLUID IS AN EXCELLENT CHOICE AS THE CHROMATOGRAPHIC MOBILE PHASE BECAUSE IT ALLOWS RAPID SEPARATION WITH HIGH EFFICIENCY AND APPLICATIONS INVOLVING ENANTIORESOLUTION ARE COMMON. SUPERCRITICAL FLUID CHROMATOGRAPHY (SFC) IS INCREASINGLY USED FOR ANALYTICAL, SEMI-PREPARATIVE AND PREPARATIVE PURIFICATION OF CHIRAL COMPOUNDS, INCLUDING PRODUCTION OF ENANTIOMERS THAT ARE MAINLY ENCOUNTERED DURING DRUG DEVELOPMENT. SFC...
-
Can Communication Power of Separable Correlations Exceed That of Entanglement Resource?
PublikacjaThe scenario of remote state preparation with a shared correlated quantum state and one bit of forward communication [B. Dakić et al., Nat. Phys. 8, 666 (2012)] is considered. Optimization of the transmission efficiency is extended to include general encoding and decoding strategies. The importance of the use of linear fidelity is recognized. It is shown that separable states cannot exceed the efficiency of entangled states by...
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublikacjaThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Comparison and Optimization of Saccharification Conditions of Alkaline Pre-Treated Triticale Straw for Acid and Enzymatic Hydrolysis Followed by Ethanol Fermentation
PublikacjaThis paper concerns the comparison of the efficiency of two-stage hydrolysis processes, i.e., alkaline pre-treatment and acid hydrolysis, as well as alkaline pre-treatment followed by enzymatic hydrolysis, carried out in order to obtain reducing sugars from triticale straw. For each of the analyzed systems, the optimization of the processing conditions was carried out with respect to the glucose yield. For the alkaline pre-treatment,...
-
Composites in energy storing prosthetic feet
PublikacjaComposites reinforced with carbon and glass fibers have become the commonly used material in the production of energy storing prosthetic feet (ESPF/elastic feet prostheses). Their properties ensure a stable and light structure that allows for accumulation, storage and release of energy during walking, thus ensuring an increase in gait efficiency. Depending on the modification of the composite in terms of fiber selection, their...
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublikacjaAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...