Filtry
wszystkich: 1536
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EXPERIMENTAL RESULTS
-
Modelowanie dynamiki odbieraka prądu pojazdu kolejowego do celów diagnostycznych
PublikacjaNiewłaściwa współpraca odbieraka prądu i sieci trakcyjnej, w trudnych warunkach lokalnych, może prowadzić do uszkodzenia sieci trakcyjnej i pantografu. W ramach rozwoju metod monitoringu i diagnostyki dla tych podsystemów, tworzone są nowe i dokładniejsze narzędzia symulacyjne, których zakres obejmuje modelowanie zarówno napowietrznej sieci trakcyjnej i pantografu, a także ich dynamicznego oddziaływania. Głównym celem jest dokładniejsza...
-
Speech codec enhancements utilizing time compression and perceptual coding
PublikacjaA method for encoding wideband speech signal employing standardized narrowband speech codecs is presented as well as experimental results concerning detection of tonal spectral components. The speech signal sampled with a higher sampling rate than it is suitable for narrowband coding algorithm is compressed in order to decrease the amount of samples. Next, the time-compressed representation of a signal is encoded using a narrowband...
-
Dead time effects compensation strategy by third harmonic injection for a five-phase inverter
PublikacjaThis paper proposes a method for compensation of dead-time effects for a fivephase inverter. In the proposed method an additional control subsystem was added to the field-oriented control (FOC) scheme in the coordinate system mapped to the third harmonic. The additional control loop operates in the fixed, orthogonal reference frame ( α - β coordinates) without the need for additional Park transformations. The purpose of this method...
-
Novel Nonlinear High Order Technologies for Damage Diagnosis of Complex Assets
PublikacjaFor the first time worldwide, innovative techniques, generic non-linear higher-order unnormalized cross-correlations of spectral moduli, for the diagnosis of complex assets, are proposed. The normalization of the proposed techniques is based on the absolute central moments, that have been proposed and widely investigated in mathematical works. The existing higher-order, crosscovariances of complex spectral components are not sufficiently...
-
Practical Approach to IP Scheduled Throughput Measurements in Dual Connectivity Systems
PublikacjaIP scheduled throughput defined according to 3GPP TS 36.314 reflects user throughput regardless of traffic characteristics, and therefore has become one of the most important indicators for monitoring Quality of Service (QoS) of the end user in Evolved Universal Terrestrial Radio Access Network (E-UTRAN). However, networks built on a distributed architecture make the above definition impossible to be applied directly due to the...
-
The effect of preliminary creep-strain on material behavior under LCF tension/compression and pure torsion regimes
PublikacjaThis paper presents the results of experimental tests of monotonic tension and torsion, creep-rupture and preliminary creep at 200C and 300C, as well as low-cycle fatigue of 2024 T3511 aluminum alloy. The fatigue process was conducted at room temperature for uniaxial tension/compression and torsion. The as-received material and pre-deformed material were also investigated during creep at elevated temperature. Basic monotonic,...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublikacjaThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublikacjaThe paper presents investigation into the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. Experiments were conducted using the nozzle size of 70 and 100 mikrometer respectively. In the course of investigations obtained were experimental relations between heat flux and wall superheating. It was proved that the phenomenon is similar to that of pool boiling...
-
Improving Control Dynamics of PMSM Drive by Estimating Zero-Delay Current Value
PublikacjaDynamic performance of current control loop still remains crucial for position-, speed-, and torque-controlled drives. In the study, a current loop solution has been designed for field oriented control of permanent magnet synchronous motors (PMSM). It enhances typical PI controller with an estimator of zero-delay current (ZDC) value. The ZDC estimation allows for selecting substantially higher controller gain. It reduces control...
-
NUMERICAL SIMULATIONS OF GAP FLOW ABOVE ROTATING DISK
PublikacjaA rotating disk can be considered a basic configuration for the investigati ons of the impact of various conditions on the flow through the clearance between the s hrouded turbine blade and the casing. Numerical calculations using Fine/Turbo Numeca were conducted to examine the influence of the rotational velocity and the pressure differ ence across the disk on the flow conditions, especially the mass flow through the clearance....
-
A simplified behavioral MOSFET model based on parameters extraction for circuit simulations.
PublikacjaThe paper presents results on behavior modeling of general purpose Metal-Oxide Semiconductor Field-Effect Transistor (MOSFET) for simulation of power electronics systems requiring accuracy both in steady-state and in switching conditions. Methods of parameters extraction including nonlinearity of parasitic capacitances and steady-state characteristics are based on manufacturer data sheet and externally measurable characteristics....
-
Velocity measurement using the fdoa method in ground-based radio navigation system
PublikacjaVelocity is one of the main navigation parameters of the moving objects. However some systems of position estimation using radio wave measurements cannot provide velocity data due to limitation of their performance. In this paper a velocity measurement method for DS-CDMA radio navigation system is proposed, which doesn’t require full synchronization of reference stations carrier frequencies. The article presents basics of FDOA...
-
Novel topology of compact coplanar waveguide resonant cell low-pass filter
PublikacjaIn this study, a novel pseudoelliptic function low-pass filter (LPF) constituted by a compact coplanar waveguide resonant cell has been designed and manufactured. The lumped-element seven-pole prototype has been adequately realized by using complementary perturbations located both in signal line and ground plane metallization. The fabricated uniplanar LPF offers a compact size of 5.6 x 9.8 mm2, return loss better than 26 dB over...
-
Movement perception with the use of a motorized delta armrest and virtual reality
PublikacjaIn this paper we present a combination of neuroscience experiments with the use of a parallel armrest robot to study the effects of temporal delays and spatial biases on the movement perception. A dedicated armrest to guide and manipulate the arm has been developed for these experiments. It is a three-degree-of-freedom Delta structure. In combination with a virtual reality application, the movement perception has been evaluated....
-
Modern technologies in energy demand reducing of public transport — Practical applications
PublikacjaCity of Gdynia (Poland) exploits one of the most modern trolleybus network in Europe, which has been involved in many projects related to the reduction of energy consumption. Some of them are connected with the improving of energy breaking recovery usage. An experimental stationary storage system at Północna substation, which was tested in 2012-2014, is a bright example of a system which is connected with the improving of the...
-
Feature Reduction Using Similarity Measure in Object Detector Learning with Haar-like Features
PublikacjaThis paper presents two methods of training complexity reduction by additional selection of features to check in object detector training task by AdaBoost training algorithm. In the first method, the features with weak performance at first weak classifier building process are reduced based on a list of features sorted by minimum weighted error. In the second method the feature similarity measures are used to throw away that features...
-
Hierarchical Estimation of Human Upper Body Based on 2D Observation Utilizing Evolutionary Programming and 'Genetic Memory'
PublikacjaNew method of the human body pose estimation based on single camera 2D observation is presented. It employs 3D model of the human body, and genetic algorithm combined with annealed particle filter for searching the global optimum of model state, best matching the object's 2D observation. Additionally, motion cost metric is employed, considering current pose and history of the body movement, favouring the estimates with the lowest...
-
Timber-frame house resistant to dynamic loads - analysis of wall panel filled with polyurethane foam
PublikacjaThe present study shows the experimentally and numerically determined response of a single timber-frame house wall panel filled with polyurethane (PU) foam under dynamic loads. The harmonic tests were conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified displacement. Based on the results of the comparison between the experimental tests and the numerical analyses, the numerical...
-
Three-point bending test of sandwich beams supporting the GFRP footbridge design process - validation
PublikacjaSome selected aspects concerning material and construction design issues for pedestrian footbridge made of GFRP composite materials are elaborated in this paper. The analysis is focused on validation tests, which are particularly important because of the advanced technology and materials that are used for this innovative bridge. The considered footbridge is a sandwich-type shell structure comprising of PET foam core and outer skins...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublikacjaThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Isothermal Vulcanization and Non-Isothermal Degradation Kinetics of XNBR/Epoxy/XNBR-g-Halloysite Nanotubes (HNT) Nanocomposites
PublikacjaThe effect of several concentrations of carboxylated nitrile butadiene rubber (XNBR) functionalized halloysite nanotubes (XHNTs) on the vulcanization and degradation kinetics of XNBR/epoxy compounds were evaluated using experimental and theoretical methods. The isothermal vulcanization kinetics were studied at various temperatures by rheometry and differential scanning calorimetry (DSC). The results obtained indicated that the...
-
Diamond Structures for Tuning of the Finesse Coefficient of Photonic Devices
PublikacjaFinesse coefficient is one of the most important parameters describing the properties of a resonant cavity. In this research, a mathematical investigation of the application of diamond structures in a fiber-optic Fabry–Perot measurement head to assess their impact on the finesse coefficient is proposed. We present modeled transmission functions of cavities utilizing a nitrogen-doped diamond, a boron-doped diamond, nanocrystalline...
-
The effect of groyne field on trapping macroplastic. Preliminary results from laboratory experiments
PublikacjaMacroplastic, a precursor of microplastic pollution, has become a new scope of research interest. However, the physical processes of macroplastic transport and deposition in rivers are poorly understood, which makes the decisions of where to locate macroplastic trapping infrastructure difficult. In this research, we conducted a series of experiments in a laboratory channel, exploring the impact of groynes and flexible artificial...
-
Badania laboratoryjne wybranych sposobów koordynacji regulatora transformatora blokowego oraz regulatora generatora
PublikacjaWprowadzenie wymogu stosowania transformatorów blokowych z przekładnią regulowaną pod obciążeniem spowodowało konieczność określenia właściwego sposobu podziału kryteriów sterowania pomiędzy regulator generatora a regulator transformatora blokowego. W referacie zwrócono uwagę na aspekt miejsca pomiaru napięć. Ma to istotny wpływ zarówno na algorytm jak i jakość regulacji. Rozważania teoretyczne zilustrowane zostały wynikami prób...
-
DEFORMATIONS OF INNOVATIVE COLD-FORMED GEB SECTIONS
PublikacjaPermanent urban growth of the world of today world implies demanding challenges for the steel construction industry. Nowadays, one of the most important issues is the cost optimization of steel structures. Since the weight of building materials is a major component of the total cost, engineers and designers try to reduce structural weight, without compromising durability and sustainability of a steel structure. Therefore, light...
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublikacjaT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
Increasing the Utilization of dc-link Voltage of a Five-Leg VSI Based on Rotor Angle Control of Dual Induction Motors
PublikacjaThis paper introduces an increased utilization of the dc-link voltage of a five-leg voltage source inverter (VSI) based on the rotor flux angle control technique for dual induction motors, IM. The main purpose is to utilize additional abilities provided by a multi-motor drive system in limited operating conditions. Generally, a multi-motor drive system is widely used in electric vehicles (EVs), traction systems and in several industrial...
-
Heat transfer enhancement of modular thermal energy storage unit for reversible heat pump cooperation
PublikacjaThe following article presents experimental comparison research on a hexagonal shelland-tube latent thermal energy storage (TES). Such shape of a shell was deliberately chosen instead of a cylindrical one due to its high modularity and with intent for future applications in automobiles (EV and PHEV) air conditioning systems (HVAC). Two geometries of helical coils, acting as tubes, were studied in this article. One was a simple...
-
A methodology for ultimate strength assessment of ship hull girder accounting for enhanced corrosion degradation modelling
PublikacjaThe presented work shows a methodology for the ultimate strength assessment of a ship hull, considering enhanced corrosion modelling. The approach is based on the classical Smith method. However, the recent findings regarding the impact of corrosion degradation on ultimate strength are incorporated. To this end, the stress–strain relationships for particular elements composing ship hull cross-section are modified using a specially...
-
NEW SOLUTIONS FOR THE SOLAR CHARGE CONTROLLERS DESIGN FOR OBTAINING TRUE MPP IN PARTLY SHADED PV MODULES
PublikacjaSoft shading sources such as tree limbs, structural elements of buildings and chimneys, scatter and refract sunlight, significantly reducing the amount of radiation reaching the surface of the module. The hard shadings located directly on the surface (i.e. bird droppings, leaves, snow) tend to stop sunlight completely. These phenomena significantly affects the output characteristics of photovoltaic modules and often contribute...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublikacjaThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Expedited simulation-driven design optimization of UWB antennas by means of response features
PublikacjaIn this work, a method for fast design optimization of broadband antennas is considered. The approach is based on a feature-based optimization (FBO) concept where reflection characteristics of the structure at hand are formulated in terms of suitably defined feature points. Redefinition of the design problem allows for reducing the design optimization cost, because the dependence of feature point coordinates on antenna dimensions...
-
Techno‐economic evaluation of a natural deep eutectic solvent‐based biorefinery: Exploring different design scenarios
PublikacjaThis paper presents a comprehensive techno‐economic evaluation of an integrated natural deep eutectic solvent (NADES)‐based biorefinery – a 1 ton day−1 capacity design plant. The key parameters include payback period, net present value (NPV), and internal rate of return (IRR). These were compared with the parameters of conventional biorefineries. The ‘n th plant’ results clearly revealed that the single product‐based biorefinery...
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublikacjaIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
Immittance Studies of Bi6Fe2Ti3O18 Ceramics
PublikacjaResults of studies focusing on the electric behavior of Bi6Fe2Ti3O18 (BFTO) ceramics are reported. BFTO ceramics were fabricated by solid state reaction methods. The simple oxides Bi2O3, TiO2, and Fe2O3 were used as starting materials. Immittance spectroscopy was chosen as a method to characterize electric and dielectric properties of polycrystalline ceramics. The experimental data were measured in the frequency range D = (101–107)...
-
Effect of urea and glycine betaine on the hydration sphere of model molecules for the surface features of proteins
PublikacjaWater properties may significantly affect protein stability. Osmolytes are compounds that intrinsically affect water in many different ways and thus can influence proteins with this type of indirect mechanism. In this study, we characterize water properties in ternary solutions: model–water–osmolyte, with two model molecules: N-methylacetamide (NMA) and dimethyl sulfoxide (DMSO) and two osmolytes: glycine betaine (TMG)and urea....
-
DFT study of low-energy electron interaction with pyridine, pyrazine and their halo derivatives
PublikacjaIn this work, the density functional theory with B3LYP hybrid functional was employed to calculate quantities useful for estimating the behavior of pyridine, pyrazine and their derivatives monosubstituted with Cl or Br atom, when exposed to low-energy electron impact. Vertical electron affinities obtained in several Pople basis sets and in aug-cc-pVTZ basis set are reported. Although some of the investigated molecules do not form...
-
A coupled constitutive model for fracture in plain concrete based on continuum theory with non-local softening and eXtended Finite Element Method
PublikacjaThe paper presents a constitutive model for concrete which combines a continuous and discontinuous fracture description. In a continuum regime, two different constitutive laws were used. First, a plasticity model with a Rankine failure criterion and an associated fl ow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. In order to capture the width of a localized zone and to obtain mesh-independent...
-
Simple empirical formula to estimate the main geomechanical parameters of preplaced aggregate concrete and conventional concrete
PublikacjaPreplaced aggregate concrete (PAC) or two-stage concrete is a specific type of concrete successfully employed in many projects including underwater concrete structures, massive concrete structures, structures made of reinforced concrete, and improvement of concrete structures. PAC is significantly different than the conventional concrete. In this type of concrete, aggregates are initially poured into the mold, the voids between...
-
Experimental research on a hydrodynamic thrust bearing with hydrostatic lift pockets: Influence of lubrication modes on bearing performance
PublikacjaThe aim of the study is to investigate the performance of a thrust bearing equipped with hydrostatic lift pockets under different lubrication modes. Three types of flat land bearing lubrication modes are studied experimentally: hydrostatic lubrication (HS; forced oil injection to the pockets), hybrid lubrication (HS + HD; hydrostatic lubrication combined with the external forced bearing oil supply) and hydrodynamic lubrication...
-
Mechanics of mesh implanted into abdominal wall under repetitive load. Experimental and numerical study
PublikacjaThere are a number of papers discussing medical and mechanical aspects of ventral hernia management. Despite intensive work on the problem understanding, recurrences of the sickness still happen too often. For that reason new aspects of the problem must be considered. In this paper, a change in the abdominal implant’s stiffness is discussed, which is caused by cyclic loading. Such loading influence abdominal implant e.g. while...
-
The role of low-energy electrons in the charging process of LISA test masses
PublikacjaThe estimate of the total electron yield is fundamental for our understanding of the test-mass charging associated with cosmic rays in the Laser Interferometer Space Antenna (LISA) Pathfinder mission and in the forthcoming gravitational wave observatory LISA. To unveil the role of low energy electrons in this process owing to galactic and solar energetic particle events, in this work we study the interaction of keV and sub-keV...
-
Non-Adaptive Speed and Position Estimation of Doubly-Fed Induction Generator in Grid-Connected Operations
PublikacjaThe nonadaptive speed and position estimation scheme for a doubly-fed induction generator (DFIG) is presented in this article. The observer structure is based on the extension of the mathematical model of DFIG to the introduced H vector. Based on the defined H vector, the nonadaptive position and speed estimation is proposed. The Lyapunov method is extended to the practical stability theorem to stabilize the structure. The classic...
-
In-ADC, Rank-Order Filter for Digital Pixel Sensors
PublikacjaThis paper presents a new implementation of the rank-order filter, which is established on a parallel-operated array of single-slope (SS) analog-to-digital converters (ADCs). The SS ADCs use an “on-the-ramp processing” technique, i.e., filtration is performed along with analog-to-digital conversion, so the final states of the converters represent a filtered image. A proof-of-concept 64 × 64 array of SS ADCs, integrated with MOS...
-
Verification of ESPAR Antennas Performance in the Simple and Calibration Free Localization System
PublikacjaThis paper presents the results of simulations and measurements of an indoor localization system that uses Electronically Steerable Parasitic Array Radiator (ESPAR) antennas with switched directional beam. Proposed antennas are dedicated for 2.4GHz ISM low-cost applications where determination of the incoming signal is required. The antennas performance is analyzed and verified with relation to positioning methods based on the...
-
Comparative molecular modelling of biologically active sterols
PublikacjaMembrane sterols are targets for a clinically important antifungal agent – amphotericin B. The relatively specific antifungal action of the drug is based on a stronger interaction of amphotericin B with fungal ergosterol than with mammalian cholesterol. Conformational space occupied by six sterols has been defined using the molecular dynamics method to establish if the conformational features correspond to the preferential interaction...
-
Low energy electron attachment to platinum(II) bromide (PtBr2)
PublikacjatDissociative electron attachment to PtBr2in the gas phase was studied in the low electron energy rangefrom zero up to 10 eV with an energy resolution of 150 meV. The experiments were carried out using ahemispherical electron monochromator coupled with a quadrupole mass spectrometer and pulse count-ing acquisition system. The only anion observed was Br−. This ion is formed at three resonance electronenergies: 0.4 eV, 1.2 eV and...
-
Domestic ORC micro-CHP combined with a commercial gas boiler
PublikacjaThe chapter presents the results of experimental studies conducted during the launch of the first in Poland demonstration prototype of the micro ORC coupled to a domestic gas boiler. The accomplished studies indicated the possibility for the ORC module to work with such boiler (autonomous source of heat) with a prototype single-stage axial micro turbine as the expansion machine. Confirmation of that fact has been delineated in...
-
Z type Observer Backstepping For Induction Machines
PublikacjaThis paper contains a relatively new synthesis method for non-linear objects, named backstepping. This method can be used to obtain the observer structure. The paper presents the structure of the speed observer which is a new proposition of observer backstepping with additional state variables marked Z. The rotor speed can be estimated in three different ways. The first is based on the adaptive approach, the second on the nonadaptive...
-
Performance of a hybrid microjet – microchannel cooling module
PublikacjaThe paper presents the experimental investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary...