Wyniki wyszukiwania dla: sliding table saw
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublikacjaWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
A method for measurements of geometry and positions of circular saw teethMetoda merania geometrie a polohy zubov v tele piloveho kotuca
PublikacjaW pracy przedstawiono sposób określania geometrii i położenia ostrzy piły tarczowej. Opisano metodę bazująca na numerycznej obróbce zarejestrowanych obrazów ostrzy pił w sposób automatyczny na automatycznym urządzeniu WKOPTar.
-
Metoda badania powłok ceramicznych w ruchu postępowo-zwrotnym = A method for testing of ceramic coatings under reciprocating sliding
PublikacjaOpracowano metodę badania powłok ceramicznych w warunkach tarcia ślizgowego na próbkach tworzących układ o styku niekonforemnym kula - powierzchnia płaska. Pokryte warstwą ceramiczną kule dociskano do próbek płaskich - prostopadłościennych listew (również pokrytych ceramiką), wykonujących ruch postępowo-zwrotny. Jako stanowisko badawcze zastosowano Tribometr Posuwisto-zwrotny TPZ-1. Przebieg zużywania się powłoki ceramicznej oceniano...
-
Friction and wear behaviour of self mated DLC and DLC-W coatings in water or salt in water solution lubricated sliding
PublikacjaPrzedstawiono wyniki badań powłok ceramicznych DLC oraz DLC z wolframem (DLC-W) nałożonych na podłoże ze stali nierdzewnej,przy tarciu ślizgowym , w modelowym skojarzeniu o styku konforemnym (płaskie czoło obracającej się względem swojej osi tulei - powierzchnia płaska). Badania prowadzono stosując smarowanie wodą destylowaną albo wodnym roztworem soli - NaCl. Wyznaczano współczynniki tarcia oraz intensywność zużywania ceramicznej...
-
Wojciech Litwin dr hab. inż.
Osoby1992÷1996 – Studia na Wydziale Mechanicznym Politechniki Gdańskiej1996 – Zatrudniony na Wydziale Oceanotechniki i Okrętownictwa PG2004 – Obrona pracy doktorskiej2014 – obrona rozprawy habilitacyjnej2012 – obejmuje funkcję prodziekan ds. Nauki na Wydziale Oceanotechniki i OkrętownictwaUczestniczył w wielu projektach badawczych oraz pracach zleconych przez przemysł związanych z łożyskowaniem ślizgowym wałów głównych oraz niekonwencjonalnymi...
-
Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearing
Publikacjacomposite. Eachofitslayershasanimportantfunction.Speciallypreparedslidingsurfaceensures minimum resistance.Followingrunning-initssmoothnessbecomesveryhighandthebearingmay continue workingunder fluid lubricationregime.NBRlayerensuresbearingelasticity,goodvibration damping propertiesandinsusceptibilitytoshaftaxismisalignment.Theexternalbrasslayermakes fitting thebearingeasier. Experiment resultsoftheconductedresearchwerecomparedwiththoseforarubberbearingof similar...
-
The extended model predictive-sliding mode control of three-level AC/DC power converters with output voltage and load resistance variations
Publikacja -
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
Badania uszkodzeń powłok ceramicznych wskutek tarcia ślizgowego w ruchu postępowo-zwrotnym = Wear pattern testing of ceramic coatings under reciprocating sliding
PublikacjaBadano (wykorzystując mikroskop optyczny oraz skaningowy) morfologię uszkodzeń wybranych powłok ceramicznych ( m.in. DLC z dodatkiem wolframu) nakładanych na podłoże stalowe, będących skutkiem tarcia slizgowego w ruchu postępowo-zwrotnym skojarzenia kula-powierzchnia płaska. Ślady zużycia na kulach, czyli obszary wygładzonych plateau, mają kształt zbliżony do elipsy. Praca, przy zmiennym zwrocie sił stycznych działających na powierzchnię...
-
The effect of thermal modification of ash wood on granularity and homogeneity of sawdust in the sawing process on a sash gang saw PRW 15-M in view of its technological usefulness
PublikacjaPrzedstawiono wyniki analiz granulometrycznych trocin, drewna jesionowego niemodyfikowanego (Fraxinus exelsior L.) i modyfikowanego termicznie, otrzymanych w procesie przecinania drewna na pilarce ramowej wielopiłowej PRW15-M. Przecinanie drewna prowadzono dla dwu prędkości posuwu 0,36 m·min-1 oraz 1,67 m·min-1. Ziarnistośćpowstających trocin dla drewna jesionowego modyfikowanego termicznie zawierała się w przedziale od 33,5 μm...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #24 - #25.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #24 (upper, rotating), #25 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #30 - #31.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #30 (upper, rotating), #31 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #20 - #21.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #20 (upper, rotating), #21 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #22 - #23.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #22 (upper, rotating), #23 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #26 - #27.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #26 (upper, rotating), #27 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Toward a universal Embedded-Atom Method: II. A set of transferable denisty and dimmer referenced embedding energy functions for all elements of the periodic table as tool for removing two gauge degrees of freedom in EAM potentials
PublikacjaZestaw kluczowych właściwości homodwuatomowych cząsteczek o Z ≤ 103 (równowagowa odległość między atomami re, energia dysocjacji DO, Liczba falowa drgań ωe) zostały zestawione na bazie dostępnych danych eksperymantalnych oraz obliczeń za pomocą teorii funkcjonałów gęstości elektronowej B3LYP/SBKJC.
-
Multi Parameter Sliding Test Result Evaluation for the Selection of Material Pair for Wear Resistant Components of a Hydraulic Motor Dedicated for Use with Environmentally Friendly Working Fluids
Publikacja -
Multi parameter sliding test result evaluation for the selection of material pair for wear resistant components of a hydraulic motor dedicated for use with environmentally friendly working fluids
PublikacjaW referacie przedstawiono zastosowanie metody badań tribologicznych pozwalającej na dokonywanie doboru najlepszych skojarzeń tribologicznych z wybranej populacji poprzez parametryczną ocenę wyników z wielu rodzajów testów tribologicznych wykonywanych na identycznych skojarzeniach materiał - smar - materiał.
-
Comments on “Closed Form Variable Fractional Time Delay Using FFT”
PublikacjaIn this letter drawbacks of the aforementioned paper are pointed out. The proposed approach is improved with minor modifications of the discrete frequency response. This allows for design of fractional delay filters which are close to optimal and can be efficiently implemented in the frequency domain using the sliding DFT based structure. Alternatively, the derived equivalent closed form formulae for offset windows can be used...
-
Analiza możliwości wpływania na pracę promieniowego uszczelnienia ślizgowego poprzez deformowanie jego panwi = Analysis of possibility of influence on the radial sliding seals operating by deformation of the bearing sleeve
PublikacjaW referacie przedstawiono zasadę działania promieniowych uszczelnień ślizgowych oraz ukazano istotny wpływ podstawowych parametrów konstrukcyjnych na skuteczność i jakość ich pracy. Uszczelnienia te stosowane są w instalacjach okrętowych śrub nastawnych, w turbinach wodnych typu Kaplana i maszynach górniczych do drążenia tuneli. Umożliwiają one wprowadzenie oleju pod ciśnieniem do wnętrza obracającego się wału. Zapewnienie stabilnej...
-
Wpływ falistości pierścienia ślizgowego na rozpływ prądu w zestyku ślizgowym maszyny synchronicznej = Influence of slip-ring waviness on current distribution in the sliding contact of a synchronous machine
PublikacjaZestyk ślizgowy maszyny synchronicznej średniej i dużej mocy zawiera na ogół szereg równolegle pracujących szczotek na każdym z pierścieni. Szczotki znajdują się w oprawkach szczotkowych rozmieszczonych przestrzennie wzdłuż obwodu pierścienia. To sprawia, że pracują one w tej samej chwili czasowej na różnych fragmentach pierścienia ślizgowego. Nierównomierny rozpływ prądu może spowodować nadmierne obciążenie niektórych szczotek....
-
Sprzętowa implementacja transformacji Hougha w czasie rzeczywistym
PublikacjaW artykule przedstawiono implementację sprzętową w FPGA algorytmu do wykrywania kształtów aproksymowanych zbiorem linii prostych podczas przetwarzania obrazu cyfrowego w czasie rzeczywistym. W opracowanej strukturze sprzętowej podniesiono efektywność przetwarzania poprzez zastosowanie przetwarzania przepływowego, lookup table, wykorzystanie wyłącznie arytmetyki liczb całkowitych oraz rozproszenie pamięci głosowania. Eksperymentalnie...
-
EMPIRICAL ASSESMENT OF THE MAIN DRIVING SYSTEM OF THE CIRCULAR SAWING MACHINE
PublikacjaThe producers of panel saws tend to improve sawing accuracy and minimise a level of vibrations, to increase their competitiveness at the market. Mechanical vibrations in the main saw driving system, which level depend on a plethora independent factors, may really affect sawing accuracy and general machine tool vibrations. The objective of the research was to explore vibrations signals of the main spindle system, and to extract...
-
Mode vibrations of plates – experimental analysis
PublikacjaIn this paper results of the square MDF plate and circular saw blades examination with the use of the harmonic method to static identification of resonant frequencies and shapes of mode vibrations are presented. Obtained results reveled that for circular saws with large holes in a saw blade appeared two resonant frequencies for the same nodal number.
-
Przydatność białka rybiego w postaci kolagenu lub żelatyny oraz polisacharydu - kapa-karagenu do wytwarzania aktywnych opakowań biodegradowalnych = Usefulness of fish collagen, gelatin and carrageenan for preparation of active biodegradable packages
PublikacjaSummary - The possibility of use of protein films made of fish collagen or gelatin as well as polysaccharide carrageenan films as carriers of enzymes (lysozyme or lysostaphyne), for preparation of microbiologically active packages, was investigated. It was found that crosslinking of such systems with N-[3(dimethylamino)propyl]-N'-ethylcarboimide (EDC) does not influence the activity of lysozyme immobilized in the films (Table 1)....
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublikacjaThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
Rotating rod and ball
PublikacjaWe consider a mechanical system consisting of an infinite rod (a straight line) and a ball (a massless point) on the plane. The rod rotates uniformly around one of its points. The ball is reflected elastically when colliding with the rod and moves freely between consecutive hits. A sliding motion along the rod is also allowed. We prove the existence and uniqueness of the motion with a given position and velocity at a certain time...
-
Influence of magnetic field on wear in high frequency reciprocatingsliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact operating at short stroke and high frequency are presented. It was found that horizontal magnetic field with different orientations relative to the sliding direction is affecting performance of the contact. The increase in frequency of sliding reduces accumulated mass loss and lowers the surface roughness of the wear...
-
Ocena odporności powłok na bazie DLC na doraźne uszkodzenie w warunkach tarcia ślizgowego ze smarowaniem wodą i solą fizjologiczną = Evaluation of DLC based coatings resistance to instanteneous damage under sliding friction conditions with distilated water or saline lubrication
PublikacjaWykonano serię testów w celu wyznaczenia granicznych warunków wymuszenia, zdefiniowaego jako średnie naciski powierzchniowe oraz prędkość ślizgania, po przekroczeniu których następuje gwałtowne zniszczenie powłoki. Na podstawie wyników pomiarów opracowano aproksymowane charakterystyki granicznych wymuszeń w układzie p - v oraz pokrewnych dla badanych materiałów, smarów i zakresu parametrów wymuszenia.
-
Metoda prognozowania mocy skrawania przy przecinaniu piłami polskiego drewna sosnowego z uwzględnieniem wiązkości materiału obrabianego
PublikacjaW pracy zostały przedstawione wartości właściwości materiałowych tj.: wiązkość R oraz naprężenia tnące w strefie skrawania τy, dla drewna sosnowego (Pinus sylvestris L.). Badane próbki drewna pochodziły z czterech Krain Przyrodniczo - Leśnych Polski: Bałtyckiej Krainy Przyrodniczo - Leśnej (kraina A), Karpackiej Krainy Przyrodniczo - Leśnej (kraina B), Małopolskiej Krainy Przyrodniczo - Leśnej (kraina C) oraz Wielkopolsko - Pomorskiej...
-
Recovering Evaluation of Narrow-Kerf Teeth of Mini Sash Gang Saws
PublikacjaSash gang saws with narrow-kerf saw blades are used in the production of glued laminate flooring elements in plants where dry technology is applied. This means that boards or friezes are sawn into top layer lamellae in dry conditions (moisture content of about 10–12%) from expensive wood species, often exotic. The object of this research was stellite-tipped teeth of narrow kerf saw blades sharpened under industrial conditions....
-
HMSE: A tool for coupling MODFLOW and HYDRUS-1D computer programs
PublikacjaA new software HMSE has been developed to facilitate external coupling between two well-known programs for subsurface flow modeling: MODFLOW-2005 (saturated zone flow) and HYDRUS-1D (unsaturated zone flow). Two coupling schemes have been implemented. In the first case the groundwater recharge flux is calculated by HYDRUS-1D assuming a fixed water table position and then passed to MODFLOW input files. In the second case the water...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Nonlinear Model of Synchronous Generator for Autonomous Electrical Power Systems Analysis
PublikacjaThis paper presents the nonlinear lookup table model for synchronous generator (SG) analysis. The saturation effects of the SG magnetic circuit have been considered. The saturated characteristic of the SG magnetic circuit are based on the open circuit saturation curve for magnetizing inductances. The model has been implemented into the Synopsys/Saber software using the MAST modelling language. To implement the no-load voltage characteristic...
-
Capacity of Surface Production of Band Sawing in Manufacture of Oak Floor Upper Layers
PublikacjaThin lamellae, corresponding to the layer components of structural glued members, i.e., 2-ply or 3-ply glued flooring, can be manufactured in re-sawing operations of kiln-dried wood blocks or in wet technologies, which currently seem to be more common because of the shorter drying time. The re-sawing process in wet technology is conducted on dedicated thin-cutting band sawing machines with stellite-tipped band saws. The goal of...
-
Theoretical study of thermofrictional oscillations due to negative friction-temperature characteristic
PublikacjaAnalytical study on oscillations of a body on a moving counterbody has been done by assuming imperfect frictional thermal contact and friction that decreases with contact temperature. It has been shown that stick-slip oscillation occurs due to decrease of friction coefficient when the body moves in the opposite direction to the counterbody. Dynamical characteristics, such as conditions for stable sliding and limit cycles, have...
-
IRAP tax differentiation in Italian Regions
Dane BadawczeThe following table presents the widespread differentiation in the standard IRAP rates applied in the particular regions of Italy. The tax rates in the table have been updated to 2019 (Only Regions marked with "*" updated their tax rates to the 2020 tax period as of March 16, 2020).
-
Wpływ wybranych właściwości maszyny badawczej na wynik eksperymentu tribologicznego z tarciem ślizgowym
PublikacjaNiniejsza monografia stanowi podsumowanie przekrojowych badań związanych z wpływem właściwości stanowiska badawczego (tribometru) na przebieg i rejestrowane wyniki eksperymentu tribologicznego z tarciem ślizgowym ciał stałych smarowanych cieczą w warunkach tarcia bez efektów smarowania hydrodynamicznego. Autor przedstawia wyniki kompleksowych analiz właściwości dynamicznych stanowiska badawczego w kontekście efektów obserwowanych...
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublikacjaThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...
-
Pipelined division of signed numbers with the use of residue arithmetic for small number range with the programmable gate array
PublikacjaIn this work an architecture of the pipelined signed residue divider for the small number range is presented. Its operation is based on reciprocal calculation and multiplication by the dividend. The divisor in the signed binary form is used to compute the approximated reciprocal in the residue form by the table look-up. In order to limit the look-up table address an algorithm based on segmentation of the divisor into two segments...
-
Number of active users of the mobile banking application (only a mobile phone) - 2017
Dane BadawczeCustomers using mobile devices can use their bank account via the bank's website or a separate application. Such a solution allows for easier logging in (usually no customer number is required, but only a password) and a number of additional functions (from a more extensive interface to a larger number of possible operations - making a transfer, opening...
-
Wpływ warunków spawania na własności złączy spawanych ze stali superduplex
PublikacjaW pracy przedstawiono charakterystykę stali duplex i superduplex koncentrując się na ich spawalności. Zaprezentowano wyniki badań własności mechanicznych złączy spawanych ze stali superduplex wykonanych metodami FCAW i SAW.
-
Technologie spawalnicze w okrętownictwie
PublikacjaOmówiono skrótowo: cieplne klasyczne technologie spawalnicze (cięcie i spawanie MMA, SAW, CAW, GMAW, MIG-MAG) oraz technologie rozwoju spawania plazmowego, laserowego i hybrydowego oraz zgrzewania tarciowego z przemieszczeniem (FSW).
-
Towards Safety Case Integration with Hazard Analysis for Medical Devices
PublikacjaSafety case is one of system safety lifecycle products and should be consistent with other lifecycle products like hazard analysis results. In this paper we present a method of safety case integration with hazard tables based on the use of parametrized argument patterns. We describe a hazard table metamodel, a safety argument pattern and a mechanism of pattern instantiation using a linking table which represents references to system...
-
Pipelined division of signed numbers with the use of residue arithmetic in FPGA
PublikacjaAn architecture of a pipelined signed residue divider for small number ranges is presented. The divider makes use of the multiplicative division algorithm where initially the reciprocal of the divisor is calculated and subsequently multiplied by the dividend. The divisor represented in the signed binary form is used to compute the approximated reciprocal in the residue form by the table look-up. In order to reduce the needed length...
-
Lateral forces determine dimensional accuracy of the narrow‑kerf sawing of wood
PublikacjaThe shrinking global forest area limits the supply of industrially usable raw resources. This, in combination with the ever‑increasing consumption of timber due to population growth can lead to the lack of a positive balance between the annual volumetric growth and consumption of wood. An important innovation toward increasing environmental and economic sustainability of timber production is to reduce the volume of wood residues...
-
Empirically adjusted and consistent set of EHT valence orbital parametersfor all elements of the periodic table. Modelling Simul. Mater. Sci. Eng. [online]. 2004 vol. 12 [dostęp..] s. 21-32, 3 rys. 3 tab. bibliogr. 35 poz. Dostępny w Internecie stacks.iop.org/MSMSE/12/21.ISSN 0965-0393 Jednorodny skorygowany empirycznie zbiór parametrów EHT dla orbitali walen- cyjnych pierwiastków.
PublikacjaModel atomu HFS został zmodyfikowany poprzez przypisanie każdemu z atomówindywidualnego parametru ŕ. Wartości ŕ dobrano w oparciu o pierwszy poten-cjał jonizacji atomu. Parametry EHT wyznaczono w oparciu o tak zmodyfikowa-ny model HFS.
-
Contact with coupled adhesion and friction: Computational framework, applications, and new insights
PublikacjaContact involving soft materials often combines dry adhesion, sliding friction, and large deformations. At the local level, these three aspects are rarely captured simultaneously, but included in the theoretical models by Mergel et al., (2019). We here develop a corresponding finite element framework that captures 3D finite-strain contact of two deformable bodies. This framework is suitable to investigate sliding friction even...
-
Summary index of innovations for Poland, Germany and the EU average in 2008-2012
Dane BadawczeIn 2013, PoƖska became one of the so-called "modest innovators".The table illustrates changes in the innovativeness of the countries in question using the SII indicator.
-
Numerical Investigation on Dynamic Performance of a Multi-storey Steel Structure Model and Comparison with Experimental Results
PublikacjaShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Numerical investigation on dynamic performance of a multi-storey steel structure model and comparison with experimental results
PublikacjaShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
MRAS-Based Switching Linear Feedback Strategy for Sensorless Speed Control of Induction Motor Drives
PublikacjaThis paper presents a newly designed switching linear feedback structure of sliding mode control (SLF-SMC) plugged with an model reference adaptive system (MRAS) based sensorless fieldoriented control (SFOC) for induction motor (IM). Indeed, the performance of the MRAS depends mainly on the operating point and the parametric variation of the IM. Hence, the sliding mode control (SMC) could be considered a good control alternative...
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublikacjaThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
-
A pin-on-disc study of airborne wear particle emissions from studded tyre on concrete road contacts
PublikacjaStudded tyres wear surfaces of winter roads, generating inhalable airborne particles. In this study, four concrete road materials and two stud geometries were investigated in terms of wear, road material hardness and airborne particle concentration. The sliding contact between studded tyres and road materials was studied using a pin-on-disc machine in a clean chamber. The results show that the normal load and the stud size have...
-
Ekspertyza dotycząca zdiagnozowania przyczyn przelewania się wody i powstania rozlewisk w systemie retencji w postaci ogrodów deszczowych na terenie osiedla ZDROVO, ul. Niepołomicka w Gdańsku
PublikacjaCelem ekspertyzy jest przedstawienie przyczyn przelewania się wody i powstawania rozlewisk w systemie retencji w postaci ogrodów deszczowych na terenie osiedla ZDROVO przy ul. Niepołomickiej w Gdańsku. Opracowanie zawiera analizę warunków gruntowo-wodnych, analizę przeprowadzonych...
-
Finite-window RLS algorithms
PublikacjaTwo recursive least-squares (RLS) adaptive filtering algorithms are most often used in practice, the exponential and sliding (rectangular) window RLS algorithms. This popularity is mainly due to existence of low-complexity versions of these algorithms. However, these two windows are not always the best choice for identification of fast time-varying systems, when the identification performance is most important. In this paper, we...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublikacjaThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Tribological test for evaluation of Natural PEEK
Dane BadawczeTest of PEEK natural (beige color) samples with sliding speed up to 1,2 m/s and up to 8 MPa of nominal load
-
Sawing Processes as a Way of Determining Fracture Toughness and Shear Yield Stresses of Wood
PublikacjaA new computational model, based on fracture mechanics, was used to determine cutting forces. Unlike traditional computing methods, which depend on many coefficients reflecting the machining of solid wood, the new model uses two main parameters: fracture toughness and shear yield stresses. The aim of this study was to apply this new method to determine these parameters for the tooth cutting edge principal positions and longitudinal...
-
Predicting cutting power for band sawing process of pine and beech wood dried with the use of four different methods
PublikacjaWood drying is an important stage in the woodworking process. After drying, wood is subject to a re-sawing process, for which a high quality surface, low material loss, and high efficiency are often required. In this paper, forecasted values were presented of cutting power for the re-sawing process of pine and beech wood that were dried with four different methods. Forecasting of cutting power for an industrial band saw machine...
-
Results of implementation of Feed Forward Neural Networks for modeling of heat transfer coefficient during flow condensation for low and high values of saturation temperature
Dane BadawczeThis database present results of implementation of Feed Forward Neural Networks for modeling of heat transfer coefficient during flow condensation for low and high values of saturation temperature. Databse contain one table and 7 figures.
-
HYDRODYNAMIC THRUST BEARINGS WITH POLYMER LINING
PublikacjaPolymeric linings of sliding surfaces of the hydrodynamic bearings have been used successfully for over 50 years. Despite of their long history of operation and research, they have not become wide spread in industrial applications. This fact may be surprising, considering th e conclusions that have been published concerning bearing operation and design. This paper summarizes the current...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublikacjaThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
A hierarchical observer for a non-linear uncertain CSTR model of biochemical processes
PublikacjaThe problem of estimation of unmeasured state variables and unknown reaction kinetic functions for selected biochemical processes modelled as a continuous stirred tank reactor is addressed in this paper. In particular, a new hierarchical (sequential) state observer is derived to generate stable and robust estimates of the state variables and kinetic functions. The developed hierarchical observer uses an adjusted asymptotic observer...
-
Investigations of dissimilar stainless steels welded joints for chemical tankers construction
PublikacjaArtykuł przedstawia właściwości mechaniczne złączy różnoimiennych stali typu duplex oraz austenitycznej typu 316L otrzymanych za pomocą spawania automatycznego łukiem krytym. Wykazano możliwość wykorzystania wysokowydajnej metody SAW w miejsce dotychczas stosowanych metod GTAW i GMAW do spawania blach zbiorników statków do przewozu chemikaliów.
-
Borderline Brenner tumor - Female, 62 - Tissue image [1001072953432531]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Borderline Brenner tumor - Female, 62 - Tissue image [10010729534327531]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Borderline Brenner tumor - Female, 62 - Tissue image [10010729534323491]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Borderline Brenner tumor - Female, 62 - Tissue image [10010729534326771]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Borderline Brenner tumor - Female, 62 - Tissue image [10010729534324211]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Fracture Toughness and Shear Yield Strength Determination for Two Selected Species of Central European Provenance
PublikacjaWhen offcut of wood is formed by shearing, Atkins’s analyses of sawing processes can be applied. Using this modern approach, it is possible to determine the fracture toughness and shear yield strength of wood. This model is only applicable for the axial-perpendicular cutting direction because both of these parameters are suitable for the given direction of cutting edge movement and cannot be considered material constants. Alternatively,...
-
Research into flows in turbine blade seals. Part II: Numerical analysis
PublikacjaPrzedstawiono wyniki badań numerycznych programem Fluent przepływów w uszczelnieniu nadbandażowym stopnia turbinowego. Badania wykonano przy zastosowaniu różnych typów siatek obliczeniowych, różnych rodzajów "zszywek" oraz różnych metod obliczeniowych (Mixing Plane, Sliding Mesh, Multiple ReferenceFrame).
-
Fluctuation - enchanced chemical sensing
PublikacjaCzułość i selektywność sensorów gazu może ulec poprawie jednocześnie gdy wykorzysta się informację zawartą w szumach występujących w sensorze. W pracy opisano szczegółowo kilka metod stosowanych do analizy szumów sensorów gazu. Przedstawiono wyniki ostatnich eksperymentów przeprowadzonych na komercyjnych sensorach gazu Taguchi, sensorach SAW oraz MOS-FET.
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublikacjaThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
Wpływ nagniatania ślizgowego na chropowatość zewnętrznych powierzchni obrotowych w częściach maszyn
PublikacjaPodano wyniki badań technologicznych nagniatania ślizgowego wałków ze stali C45.Obróbkę przeprowadzono na tokarce CNC z użyciem nagniataka z tensometrycznym pomiarem siły docisku.Zamieszczono wytyczne dla doboru parametrów obróbki według kryterium wymaganej chropowatości powierzchni obrobianej.
-
Borderline Brenner tumor - Female, 62 - Tissue image [10010729534328621]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Borderline Brenner tumor - Female, 62 - Tissue image [10010729534329801]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
NON-STATIONARY THERMAL SELF-ACTION OF ACOUSTIC BEAMS CONTAINING SHOCK FRONTS IN THERMOCONDUCTING FLUID
PublikacjaNon-stationary thermal self-action of a periodic or impulse acoustic beam containing shock fronts in a thermoconducting Newtonian fluid is studied. Self-focusing of a saw-tooth periodic and impulse sound is considered, as well as that of a solitary shock wave which propagates with the linear sound speed. The governing equations of the beam radius are derived. Numerical simulations reveal that the thermal conductivity weakens the...
-
Właściwości mechaniczne złączy różnoimiennych stali odpornych na korozję
PublikacjaArtykuł przedstawia właściwości mechaniczne złączy różnoimiennych stali typu duplex oraz austenitycznej typu 316L otrzymanych za pomocą spawania automatycznego łukiem krytym (SAW). Wykazano możliwość wykorzystania wysokowydajnej metody spawania automatycznego łukiem krytym do łączenia blach zbiorników statków do przewozu chemikaliów. Uzyskano złącza o zadawalających właściwościach mechanicznych spełniających wymagania towarzystwa...
-
Tribological test for evaluation of CF30 Black PEEK
Dane BadawczeSample numner BL03 and BL04 made of PEEK CF30 (black color) tribologicaly tested with sliding speed up to 1,8 m/s and up to 14 MPa of nominal load under water lubrication.
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublikacjaThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.