Filtry
wszystkich: 231
Wyniki wyszukiwania dla: surface stresses
-
Bending of a Three-Layered Plate with Surface Stresses
PublikacjaWe discuss here the bending deformations of a three-layered plate taking into account surface and interfacial stresses. The first-order shear deformation plate theory and the Gurtin-Murdoch model of surface stresses will be considered and the formulae for stiffness parameters of the plate are derived. Their dependence on surface elastic moduli will be analyzed.
-
On stress singularity near the tip of a crack with surface stresses
PublikacjaIn the framework of the simplified linear Gurtin–Murdoch surface elasticity we discuss a singularity of stresses and displacements in the vicinity of a mode III crack. We show that inhomogeneity in surface elastic properties may significantly affect the solution and to change the order of singularity. We also demonstrate that implicitly or explicitly assumed symmetry of the problem may also lead to changes in solutions. Considering...
-
On Nonlinear Dynamic Theory of Thin Plates with Surface Stresses
PublikacjaWe discuss the modelling of dynamics of thin plates considering surface stresses according to Gurtin–Murdoch surface elasticity. Taking into account the surface mass density we derive the two-dimensional (2D) equations of motion. For the reduction of the three-dimensional (3D) motion equations to the 2D ones we use the trough-the-thickness integration procedure. As a result, the 2D dynamic parameters of the plate depend not only...
-
Comparison of anti-plane surface waves in strain-gradient materials and materials with surface stresses
PublikacjaHere we discuss the similarities and differences in anti-plane surface wave propagation in an elastic half-space within the framework of the theories of Gurtin–Murdoch surface elasticity and Toupin–Mindlin strain-gradient elasticity. The qualitative behaviour of the dispersion curves and the decay of the obtained solutions are quite similar. On the other hand, we show that the solutions relating to the surface elasticity model...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublikacjaThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Influence of Surface Laser Treatment on Mechanical Properties and Residual Stresses of Titanium and its Alloys
PublikacjaSurface modification of the titanium and its alloys used in implantology with a long-pulse laser can change the surface topography, but it also leads to changes in the stress sign and magnitude in the resulting subsurface layer. The presented research was aimed at evaluating the state of stress after laser remelting with the Nd:YAG laser of pre-etched titanium alloys Ti6Al4V and Ti13Nb13Zr and pure titanium. The obtained surface...
-
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublikacjaThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Application of the Finite Element Method for Modelling of the Spatial Distribution of Residual Stresses in Hybrid Surface Layers
Publikacja -
Effects of Surface Energy and Surface Residual Stresses on Vibro-Thermal Analysis of Chiral, Zigzag, and Armchair Types of SWCNTs Using Refined Beam Theory
PublikacjaIn this article, vibration characteristics of three different types of Single-Walled Carbon Nanotubes (SWCNTs) such as armchair, chiral, and zigzag carbon nanotubes have been investigated considering the effects of surface energy and surface residual stresses. The nanotubes are embedded in the elastic substrate of the Winkler type and are also exposed to low and high-temperature environments. A new refined beam theory namely, one-variable...
-
INFLUENCE OF SINGLE-STAGE AND DUPLEX SHOT PEENING ON SURFACE ROUGHNESS AND RESIDUAL STRESSES IN Al Mg5 Mn1 Sc0,8 Zr0,4 ALLOY
Publikacja -
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublikacjaLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Modeling of the Two-Dimensional Flow Caused by Sea Conditions and Wind Stresses on the Example of Dead Vistula
PublikacjaThe article presents the results of two-dimensional modeling of flows caused by the sea conditions and wind stresses on the example of Dead Vistula. Based on the available bathymetric data, a numerical model of the river section was created, which was supplemented with data on the position of the water table depending on hydrometeorological conditions. To describe the flow field in steady conditions, a simplified model of two-dimensional...
-
Surface finite viscoelasticity and surface anti-plane waves
PublikacjaWe introduce the surface viscoelasticity under finite deformations. The theory is straightforward generalization of the Gurtin–Murdoch model to materials with fading memory. Surface viscoelasticity may reflect some surface related creep/stress relaxation phenomena observed at small scales. Discussed model could also describe thin inelastic coatings or thin interfacial layers. The constitutive equations for surface stresses are...
-
Experiments and Analysis of the Limit Stresses of a Magnetorheological Fluid
PublikacjaPaper presents the results of a rheological test of a commercial magnetorheological (MR) fluid (MRF-132DG). The researchincludes the problem of measuring and interpreting limit stresses under conditions close to the magnetic saturation of the fluid. Fourdifferent limit stresses were determined, two related to the yield point and two related to the flow point. Methods for determining limitstresses, especially due to excitation...
-
Influence of geometrical imperfections on stresses in cylindrical shells
PublikacjaResults of the numerical analysis of the shells of storage tanks of 50 000 m3 capacity with geometrical imperfections are presented in the paper. Results were verified by tensometric tests performed on the real tank. It was recognized that real geometrical imperfections cause increase of stresses in the tank construction by 30%.
-
On the Bending of Multilayered Plates Considering Surface Viscoelasticity
PublikacjaWe discuss the bending resistance of multilayered plates taking into account surface/interfacial viscoelasticity. Within the linear surface viscoelasticity we introduce the surface/interfacial stresses linearly dependent on the history of surface strains. In order to underline the surface viscoelasticity contribution to the bending response we restrict ourselves to the elastic behaviour in the bulk. Using the correspondence principle...
-
Comparison of calculated and measured thermal stresses in asphalt concrete
PublikacjaThe paper presents the comparison of calculated and measured thermal stresses induced in restrained asphalt concrete specimens by cooling. Thermal stresses were measured in the Thermal Stress Restrained Specimen Test. The calculations of thermal stresses were performed with the use of a theoretical formula based on the temperature dependent stiffness modulus. The novel approach applied in this paper was that the stiffness modulus...
-
Anti-plane surface waves in media with surface structure: Discrete vs. continuum model
PublikacjaWe present a comparison of the dispersion relations derived for anti-plane surface waves using the two distinct approaches of the surface elasticity vis-a-vis the lattice dynamics. We consider an elastic half-space with surface stresses described within the Gurtin–Murdoch model, and present a formulation of its discrete counterpart that is a square lattice half-plane with surface row of particles having mass and elastic bonds different...
-
On the influence of a surface roughness on propagation of anti-plane short-length localized waves in a medium with surface coating
PublikacjaWe discuss the propagation of localized surface waves in the framework of the linear Gurtin–Murdoch surface elasticity and taking into account a roughness of a free boundary. We derive a boundary-value problem for anti-plane motions with curvilinear boundary and surface stresses. Using the asymptotic technique developed earlier, we obtain the form of a localized wave and analyze its amplitude evolution. As the main result we present...
-
Wave transmission across surface interfaces in lattice structures
PublikacjaWithin the lattice dynamics formulation, we present an exact solution for anti-plane surface waves in a square lattice strip with a surface row of material particles of two types separated by a linear interface. The considered problem is a discrete analog of an elastic half-space with surface stresses modelled through the simplified Gurtin–Murdoch model, where we have an interfacial line separating areas with different surface...
-
Estimation of Stresses in a Dry Sand Layer Tested on Shaking Table
PublikacjaTheoretical analysis of shaking table experiments, simulating earthquake response of a dry sand layer, is presented. The aim of such experiments is to study seismic-induced compaction of soil and resulting settlements. In order to determine the soil compaction, the cyclic stresses and strains should be calculated first. These stresses are caused by the cyclic horizontal acceleration at the base of soil layer, so it is important...
-
The effect of tensile stresses on aluminium passive layer durability
PublikacjaW niniejszej pracy przedstawiono wyniki badań DEIS dotyczących wpływu naprężeń rozciągających na trwałość warstwy pasywnej aluminium A91050, prowadzonych w środowisku chlorków w temperaturze pokojowej.Zastosowana technika pozwoliła na wyznaczenie krytycznej wartości wydłużenia, przy której doszło do pęknięcia warstwy pasywnej na badanym stopie.
-
Evaluation of Thermal Stresses in Asphalt Layers in Comparison with TSRST Test Results
PublikacjaThe paper presents the results of calculations and laboratory determination of thermal stresses at low temperatures. The modified Hills and Brien's method was used to calculate the thermal stresses in asphalt layers of pavements and the results were compared against the values obtained at a laboratory with the Thermal Stress Restrained Specimen Test (TSRST) method. The laboratory investigations were conducted using plain grade...
-
The Influence of Modelling Material Zones on Strains and Stresses at Weld Toe Notch
PublikacjaThe latest development in the field of welding technology enabled prefabrication of thin-walled sandwich structures in an industrial scale. Sandwich structures fabricated of steel, or aluminium alloy plates and stiffeners are welded with the use of hi-power CO2 lasers. Strength analysis of such structures with the use of finite element method needs proper material modelling.In this paper the material model of steel sandwich panel...
-
EFFECT OF SURFACE STATE AND STRESS ON AN OXIDATION OF THE ZIRCALOY-2 ALLOY
PublikacjaZr alloys are widely used as materials for nuclear fuel pellets in the nuclear industry. In the case of the LOCA or RIA happen, a temperature may locally reach high values. Even if the high temperature maintains shortly, the zirconium oxides may become permeable, absorb hydrogen appearing in cooling water from decomposition reaction and crack because of formation and brittle failure of hydrides. Such model cannot so far take into...
-
Contribution of Exogenous Proline to Abiotic Stresses Tolerance in Plants: A Review
Publikacja -
Fe analysis of loadson the silo wall and stresses in the silo structure.
PublikacjaArtykuł przedstawia numeryczne wyniki naporu materiałów sypkich na ścinanie podczas przepływu w silosach z lejem w kształcie osiowo-symetrycznego stożka.
-
Combining of global and local stresses in ship hulls on ocean waves.
PublikacjaOpisano zagadnienia superpozycji naprężeń dynamicznych od zginania ogólnego i strefowego, we wzdłużnych wiązarach kadłuba statku. Krytycznie skomentowano wymagania przepisów klasyfikacji i budowy statków, dotyczące oceny wytrzymałości tych elementów konstrukcji. Przedstawiono sposób wykonywania prognozy długoterminowej naprężeń w tych elementach i zaproponowano sposób sumowania charakterystycznych wartości naprężeń od zginania...
-
On weak solutions of boundary value problems within the surface elasticity of Nth order
PublikacjaA study of existence and uniqueness of weak solutions to boundary value problems describing an elastic body with weakly nonlocal surface elasticity is presented. The chosen model incorporates the surface strain energy as a quadratic function of the surface strain tensor and the surface deformation gradients up to Nth order. The virtual work principle, extended for higher‐order strain gradient media, serves as a basis for defining...
-
On Dynamic Boundary Conditions Within the Linear Steigmann-Ogden Model of Surface Elasticity and Strain Gradient Elasticity
PublikacjaWithin the strain gradient elasticity we discuss the dynamic boundary conditions taking into account surface stresses described by the Steigmann–Ogden model. The variational approach is applied with the use of the least action functional. The functional is represented as a sum of surface and volume integrals. The surface strain and kinetic energy densities are introduced. The Toupin–Mindlin formulation of the strain gradient elasticity...
-
Antagonist adhesion effects due to variable substrate surface
PublikacjaThe effects of variability of intrinsic adhesion within a joint have been studied using a single cantilever beam (SCB) test. Fracture energy was found not to be a simple function of relative areas of 2 surface pre-treatments: a 'weak' zone decreased strength more than expected from simple, additive considerations. By severing the adhesive along the strong-weak transition, fracture energy increased.The prior antagonist effect appears...
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublikacjaStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Sawing Processes as a Way of Determining Fracture Toughness and Shear Yield Stresses of Wood
PublikacjaA new computational model, based on fracture mechanics, was used to determine cutting forces. Unlike traditional computing methods, which depend on many coefficients reflecting the machining of solid wood, the new model uses two main parameters: fracture toughness and shear yield stresses. The aim of this study was to apply this new method to determine these parameters for the tooth cutting edge principal positions and longitudinal...
-
Application of Barkhausen method to determine internal stresses in cold-rolled and hot-rolled sheets
PublikacjaThe paper presents investigations on internal stress distribution in plane hot—or cold-rolled sheets dedicated for the cold-formed profiles. The motivation of the research is a new profile design whose bending technology, incorporating a longitudinal welded joint and hot-dip galvanization after bending and welding introduces additional internal stresses. In order to identify the entirety of stresses in the process of sheet production...
-
Evaluation of Thermal Stresses in Asphalt Layers Incomparison with TSRST Test Results
Publikacja -
On long-term prediction of stresses in principal members of ship hull structures.
PublikacjaOpisano krytycznie wymagania towarzystw klasyfikacyjnych dotyczące oceny wytrzymałości wzdłużnych wiązarów i wzdłużnych usztywnień poszycia kadłuba statku. Przedstawiono sposób prognozowania długoterminowego dynamicznych składowych tych naprężeń oraz zaproponowano sposób składania charakterystycznych wartości poszczególnych składowych naprężeń do zastosowania w przepisach Polskiego Rejestru Statków. Sposób ten bazuje na koncepcji...
-
Numerical calculation wall pressure and stresses in cylindrical silos withconical hopper
PublikacjaOmówiono wyniki numerycznego obliczania naporu materiału sypkiego na ściany silosu. Obliczenia wykonano stosując metodę elementów skończonych i sprężysto idealnie plastyczne prawo konstytutywne według Druckera-Pragera. W analizie uwzględniono wpływ osiowy i mimośrodowy.
-
Imaging of grains and internal stresses in GO Fe-Si alloy with Barkhauseneffects
PublikacjaBadano próbki stali transformatorowej Fe-Si ze strukturą zorientowaną (GO). Polowy efekt Barkhausena wykorzystano do zobrazowania ziaren pod warstwą ochronną a poziom naprężeń wewnętrznych wyznaczono wykorzystując mechaniczny efekt Barkhausena.
-
Linear Micropolar Elasticity Analysis of Stresses in Bones Under Static Loads
PublikacjaWe discuss the finite element modeling of porous materials such as bones using the linear micropolar elasticity. In order to solve static boundary-value problems, we developed new finite elements, which capture the micropolar behavior of the material. Developed elements were implemented in the commercial software ABAQUS. The modeling of a femur bone with and without implant under various stages of healing is discussed in details
-
Stresses in the zone of process openings in the shell of a vertical cylindrical steel tank
PublikacjaW dolnej części płaszcza zbiornika walcowego na ciecze konieczne jest wykonanie różnego rodzaju otworów technologicznych. Artykuł poświęcony jest analizie stanu naprężeń w strefie wzmocnień wykonywanych w sąsiedztwie otworów na rurociągi oraz na włazy wyczystkowe w płaszczu zbiornika. Ponieważ charakter zmian naprężeń, a więc i wzmocnień w strefie obu rodzajów otworów jest różny dlatego artykuł podzielony jest na dwie części, z...
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublikacjaThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
Examination of selected failure criteria with asymmetric shear stresses in the collapse analysis of laminated shells
PublikacjaThe paper is concerned with failure analysis of composite shells performed with the usage of the nonlinear 6‐parameter shell theory with drilling rotation degree of freedom. This special theory embodies naturally unlim-ited translations and rotations and is suitable for analysis of irregular shells for instance with various, partic-ularly orthogonal, intersections. The presence of the drilling rotation is inherently accompanied...
-
Stability analysis of single-walled carbon nanotubes embedded in winkler foundation placed in a thermal environment considering the surface effect using a new refined beam theory
PublikacjaThis article is devoted to investigate the stability of different types of Single Walled Carbon Nanotubes (SWCNTs) such as zigzag, chiral, and armchair types which are rested in Winkler elastic foundations exposing to both the low and high temperature environments. Also, the Surface effects which include surface energy and surface residual stresses, are taken into consideration in this study. It may be noted that the surface energy...
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublikacjaLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
A model of liquid film breakdown formed due to impingement of a two-phase jet on a horizontal surface
PublikacjaThe present work aims to provide an explanation to the phenomenon of breakdown of the thin liquid film created by impinging two-phase, liquid-gas jet. Existing in the literature models describe merely thebreakdown of single phase liquid films. The model presented here is based on examination of mass and energy equations under the applied criterion of the minimum of total energy. That allows to determinethe minimum thickness of...
-
Fracture Areas Quantitative Investigating of Bending-Torsion Fatigued Low-Alloy High-Strength Steel
PublikacjaIn this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
-
Numerical calculations of wall pressures and stresses in steel cylindrical silos with concentric and eccentric hoppers
PublikacjaArtykuł przedstawia numeryczną analize naprężeń w płaszczu silosa. Porównane zostały wyniki dla silosów o przepływie centrycznym i mimośrodowym.
-
The effect of external load on ultrasonic wave attenuation in steel bars under bending stresses
PublikacjaThe stress state in deformed solids has a significant impact on the attenuation of an ultrasonic wave propagating through the medium. Measuring a signal with certain attenuation characteristics can therefore provide useful diagnostic information about the stress state in the structure. In this work, basic principles behind a novel attenuation-based diagnostic framework are introduced. An experimental study on steel bars under three-point...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublikacjaThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
Dynamic electrochemical impedance spectroscopy measurements of passive layer cracking under static tensile stresses
Publikacja -
The determination of deformations and stresses of laser welds used for fatigue assessment of steel sandwich panel joints
PublikacjaPanele typu sandwich znajdują szerokie zastosowanie w wielu gałęziach przemysłu. W przypadku niektórych zastosowań wymagających ocenę ryzyka dużą rolę odgrywa ocena trwałości zmęczeniowej spoin laserowych paneli. W pracy prezentowane są metody wyznaczania lokalnych odkształceń i naprężeń w połączeniach spawanych w celu oceny trwałości zmęczeniowej według hipotez lokalnych naprężeń i odkształceń.
-
Dynamic elektrochemical impedance spectroscopy measurements of passive layer cracking under static tensile stresses.
PublikacjaDynamiczna elektrochemiczna spektroskopia impedancyjna umożliwia badanie podatności i odporności korozyjnej różnych materiałów konstrukcyjnych, a w szczególności określenie właściwości elektrochemicznych warstw pasywnych występujących na ich powierzchni. W wielu przypadkach pęknięcie warstwy pasywnej pod wpływem działania naprężeń rozciągających prowadzi do korozji naprężeniowej. Z tego względu badania pękania warstw pasywnych...
-
Dynamic electrochemical impedance spectroscopy measurements of passive layer cracking under static tensile stresses.
PublikacjaDynamiczna Elektrochemiczna Spektroskopia Impedancyjna umożliwia badanie podatności i odporności korozyjnej różnych materiałów konstrukcyjnych, a w szczególności określenie właściwości elektrochemicznych warstw pasywnych występujących na ich powierzchni. W wielu przypadkach pęknięcie warstwy pasywnej pod wpływem działania naprężeń rozciągających prowadzi do korozji naprężeniowej. Z tego względu badania pękania warstw pasywnych...
-
Potential and strain rate impact on the electrochemical properties of 304L stainless steel under tensile stresses.
PublikacjaPraca skupia się na badaniach aspektu elektrochemicznego i mechanicznego pękania warstwy pasywnej obecnej na stali 304L. Przedstawione zostały wyniki chwilowych zmian impedancji oraz zmiany parametrów elektrochemicznych warstwy pasywnej podczas testów rozciągania przy różnych poziomach polaryzacji anodowej oraz szybkości rozciągania. Na ich podstawie można stwierdzić, że zarówno czynnik elektrochemiczny, jak i mechaniczny wpływają...
-
The Impact of Thermal Stresses on Volume Resistivity: Performance Comparison between TR-XLPE and XLPE Cables
PublikacjaMost failures in electric power cables are attributed to the development of water trees inside the insulating materials. Thus, the development and utilization of Tree Retardant Cross-Linked Polyethylene (TR-XLPE) based cables have recently been given great attention to overcome the treeing issues. TR-XLPE cables use low-density polyethylene compounds suppressing the formation of water trees while retaining excellent electrical,...
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublikacjaThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublikacjaIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublikacjaThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublikacjaWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Effects of the preheating laser treatment on microstructure and corrosion resistance of Ti6Al4V bioalloy
PublikacjaThe laser remelting of the Ti6Al4V alloy was made on specimens pre-heated at elevated temperatures. The laser treatment effected in change of microstructures of surface layers and an appearance of blisters and numerous cracks. The corrosion tests demonstrated the decrease in corrosion resistance for each preheating temperature. The observed effects were attributed to negative influence of excessive compressive stresses with no...
-
Importance of sign conventions on analytical solutions to the wave-induced cyclic response of a poro-elastic seabed
PublikacjaThis paper discusses the influence of different sign conventions for strains and stresses, i.e. the solid mechanics sign convention and the soil mechanics sign convention, on the form of governing partial differential equations (the static equilibrium equations and the continuity equation) used to describe the wave-induced cyclic response of a poro-elastic seabed due to propagation of a sinusoidal surface water-wave. Some selected...
-
Mechanical Properties and Residual Stress Measurements of Grade IV Titanium and Ti-6Al-4V and Ti-13Nb-13Zr Titanium Alloys after Laser Treatment
PublikacjaNowadays, surface engineering focuses on research into materials for medical applications. Titanium and its alloys are prominent, especially Ti-6Al-4V and Ti-13Nb-13Zr. Samples made of pure grade IV titanium and the titanium alloys Ti-6Al-4V and Ti-13Nb-13Zr were modified via laser treatment with laser beam frequency f = 25 Hz and laser beam power P = 1000 W during a laser pulse with duration t = 1 ms. Subsequently, to analyze...
-
Surface treatment of C80U steel by long CO2 laser pulses
PublikacjaThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
Finite element models used in diagnostics of transverse cracks in bridge approach pavement
Dane BadawczeTransverse cracks in the asphalt pavement were observed on bridge structures next to single-module expansion joints with a 5 meter approach slab set at the depth of 1 m. The finite element (FE) models of the approach pavement were created to investigate the reasons of premature cracking and crack initiation mechanism over the back edge of the abutment...
-
Effect of crystallization process at cryogenic conditions on the functional properties of the SUPERSTON alloy used in production the ship's propellers
PublikacjaThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the SUPERSTON alloy used for ship's propellers. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. During the laser remelting at cryogenic conditions the microstructure changes significantly. This is related to synergistic effects of the solidification rate, phase transformations...
-
Selected problems of experimental investigation of dynamically loaded journal bearings
PublikacjaIn the paper some problems concerning relations between external bearing loadings and critical lining stresses are described for test stand with rotating load vector. According to the standard ISO 7905/1 this type of test stand, for dynamically loaded slide bearing, is recommended as a basic research unit for material testing in a complete bearing unit. The lining stress calculation results occurred being dependent on applied calculation...
-
Anti-plane shear waves in an elastic strip rigidly attached to an elastic half-space
PublikacjaWe consider the anti-plane shear waves in a domain consisting of an infinite layer with a thin coating lying on an elastic half-space. The elastic properties of the coating, layer, and half-space are assumed to be different. On the free upper surface we assume the compatibility condition within the Gurtin–Murdoch surface elasticity, whereas at the plane interface we consider perfect contact. For this problem there exist two possible...
-
Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
PublikacjaLightweight alloys made from aluminium are used to manufacture cars, trains and planes. The main parts most often manufactured from thin sheets requiring the use of milling in the manufacturing process are front panels for control systems, housing parts for electrical and electronic components. As a result of the final phase of the manufacturing process, cold rolling, residual stresses remain in the surface layers, which can influence...
-
Analysis of electrochemical parameters in time domain during the passive layer cracking occurring on the 304L stainless steel in chlorides solution under tensile stresses
Publikacja -
Analysis of electrochemical parameters in time domain during the passive layer cracking occurring on the 304L stainless steel in chlorides solution under tensile stresses.
PublikacjaDynamiczna Elektrochemiczna Spektroskopia Impedancyjna została wykorzystana do szczegółowej analizy zakresu przejścia stan pasywny - stan aktywny podczas procesu pękania warstwy pasywnej. Wpływ potencjału oraz naprężeń mechanicznych na niszczenie warstwy ochronnej występującej na stali 304L w środowisku 0.5M NaCl w pokojowej temperaturze został przestudiowany. Praca prezentuje chwilowe widma impedancyjne uzyskane przy różnych warunkach...
-
The influence oil additives on spread cracks in silicon nitride
PublikacjaThe paper presents an experimental study of the influence of oil additives (Cl, S, P, cerium dioxide (CeO2)) on spread cracks in silicon nitride. The additives Cl, S, P are bound in molecules in liquid form soluble in the base oil. The CeO2 is purely in powder form in suspension. The use of CeO2 powder was made based on the good results of polishing of silicon nitride. A ceramic angular contact ball bearing was modelled using a...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublikacjaProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
Fatigue fracture morphology of AISI H13 steel obtained by additive manufacturing
PublikacjaThe paper focuses on researching the effect of fatigue loading on metallic structure, lifetime, and fracture surface topographies in AISI H13 steel specimens obtained by selective laser melting (SLM). The topography of the fracture surfaces was measured over their entire area, according to the entire total area method, with an optical three-dimensional surface measurement system. The fatigue results of the SLM 3D printed steel...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublikacjaThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Micro-modelling of shear localization during quasi-static confined granular flow in silos using DEM
PublikacjaThe paper deals with the quasi-static confined flow of cohesionless sand in a plane strain model silo with parallel walls and a slowly movable bottom. Numerical modelling was carried out by the discrete element method (DEM) using spheres with contact moments to approximately capture a non-uniform shape of sand particles. Different initial void ratios of sand and silo wall roughness grades were employed. Regular triangular grooves...
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublikacjaHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...
-
Effect of pulse laser treatment at different process variables on mechanical behavior of carbon nanotubes electrophoretically deposited on titanium alloy
PublikacjaPurpose: Titanium and its alloys are widely used as biomaterials for long-term implants, but they are usually surface-modified due to their weak bioactivity and wear resistance. Laser processing was used to modify the surface layer, and elemental carbon was a component of the deposited coatings. This research aims to use a combination of both methods based on preliminary electrophoretic deposition of multi-wall carbon nanotubes...
-
P92 steel and inconel 617 alloy welds joint produced using ERNiCr-3 filler with GTAW process: Solidification mechanism, microstructure, mechanical properties and residual stresses
PublikacjaThe objective of the current study was to analyse the microstructure, mechanical characteristics, and residual stresses of a dissimilar welded joint (DWJ) made of P92 steel and the Inconel alloy 617 (IN617) using the gas tungsten arc welding (GTAW) method. The ERNiCr-3 filler was selected to produce the conventional V groove (VG) and narrow V groove (NVG) butt joint. The filler deficient zones in the weldments, such as the filler...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublikacjaeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Characterization of the Functionally Graded Shear Modulus of a Half-Space
PublikacjaIn this article, a method is proposed for determining parameters of the exponentialy varying shear modulus of a functionally graded half-space. The method is based on the analytical solution of the problem of pure shear of an elastic functionally graded half-space by a strip punch. The half-space has the depth-wise exponential variation of its shear modulus, whose parameters are to be determined. The problem is reduced to an integral...
-
A new anisotropic bending model for nonlinear shells: Comparison with existing models and isogeometric finite element implementation
PublikacjaA new nonlinear hyperelastic bending model for shells formulated directly in surface form is presented, and compared to four existing prominent bending models. Through an essential set of elementary nonlinear bending test cases, the membrane and bending stresses of each model are examined analytically. Only the proposed bending model passes all the test cases, while the other bending models either fail or only pass the test cases for...
-
Results after grinding C45 steel
Dane BadawczeThe database contains results from nanoindenter, scanning microscope and also X-ray diffractometer. To determine the residual stresses and the size of the crystallites in the ferrite grains in the grinded surface layer, the Williamson Hall analysis of the X-ray diffraction patterns was performed. XRD diffraction patterns were also used to perform a...
-
Experimental research of the effect of face milling strategy on the flatness deviations
PublikacjaIn this paper the dependencies between face milling strategy of EN AW6082-T6 aluminum alloy samples, with difference thicknesses (6, 8, and 12 mm) and two cold rolling directions, and flatness deviations were presented. Three strategies of milling included different proportions of material removed from both sides of the plates. This approach allowed to control the proportions of residual surface stresses on both sides of the specimens,...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublikacjaThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Separation of the effects of notch and macro residual stress on the MFL signal characteristics
PublikacjaMagnetic flux leakage (MFL) distribution for three configurations of samples has been investigated in order to study the influence of notch and plastic deformation separately as well as together. Samples have been made of S355 steel. The MFL signal measurements were carried out along the longest dimension of the sample over a length of 120 mm. Two components of magnetic field were measured: 1) tangential to the main axis and 2)...
-
CONTEMPORARY ART AND CIVIC ENGAGEMENT
PublikacjaThe paper aims to explore the potential role of contemporary art as a catalyst for social transformation and civic engagement. The research focuses on the visual arts and their power to change social attitudes in contemporary society. On the basis of theoretical, transdisciplinary approaches and analysis of artwork the paper investigates emerging forms of art and how they address pressing social issues and concerns that would otherwise...
-
Influence of laser processing of the low alloy medium carbon structural steel on the development of the fatigue crack
PublikacjaThe paper contains the results of the structural analysis, hardness tests and fatigue tests conducted for the medium carbon structural steel with low content of Cr and Ni after its processing with CO2 laser beam. Pre-cracks were made in the round compact tension (RCT) specimen used for fatigue test. Next, four paths, parallel to each other, were melted on both sides of the samples using a laser beam. The paths were perpendicular...
-
Effect of selective laser treatment on initiation of fatigue crack in the main part of an undercarriage drag strut
PublikacjaThis paper presents the results of material characterization and a fatigue test conducted for a laser-re-melted drag strut used in an aircraft landing gear. The drag strut was re-melted with a CO2 laser beam. Eight re-melted paths were made in the form of spiral lines along the axis of the drag strut. Next, the drag strut was subjected to variable loads on a testing machine simulating loads occurring when an aircraft lands. The...
-
Experimental and numerical investigations of ultimate strength of degradated structures
PublikacjaThe presented work investigates the corrosion influence on the structural behaviour of structural elements. Nine welded large-scale stiffened plates, and 30 standard small specimens have been subjected to the accelerated marine immersed conditions. After corrosion testing, the specimens have been accurately measured in terms of surface characteristics. The coupon specimens were furtherly subjected to tensile loading to develop...
-
Investigation of low-temperature cracking in newly constructed high-modulus asphalt concrete base course of a motorway pavement
PublikacjaThe paper presents the issue of low-temperature transverse cracks which have developed in newly constructed base courses made of high-modulus asphalt concrete mix (HMAC). Numerous transverse cracks developed in the analysed HMAC base during the winter season before the pavement was actually completed, both at the transverse joint locations and in the areas between them. This had not happened so far on such a scale during road construction...
-
Results of nanoindentation test to calculate residual stress in an eyelet of undercarriage drag strut after laser treatment
Dane BadawczeIn order to determine the residual stress in the laser-processed an eyelet of undercarriage drag strut, a nanoindentation test was performed before and after stress relief annealing. For this purpose, after the hardness test, the sample was subjected to stress relief annealing at 270 °C for 2 hours. Annealing was performed in a vacuum furnace. Hardness...
-
Extremal thermal loading of a bifurcation pipe
PublikacjaThe subject of considerations is a spherical bifurcation pipe of a live steam made of steel P91, which is an element of a block of coal-fired power plant working with a 18K370 turbine. As experience shows, it is a very sensitive element of the boiler pipelines. An extreme work scenario for such a block has been adopted, in which the turbine is shutting down to a warm state three times in 24 hours. This is an action dictated by...
-
Verification of the new viscoelastic method of thermal stress calculation in asphalt layers of pavements
PublikacjaThe new viscoelastic method of thermal stress calculations in asphalt layers has been developed and published recently by the author. This paper presents verification of this method. The verification is based on the comparison of the results of calculations with results of testing of thermal stresses in Thermal Stress Restrained Specimen Test. The calculations of thermal stresses according to the new method were based on rheological...
-
Mechanical Strength of MV Ship-switchgear During Fault Arc
PublikacjaIn the paper the analysis of pressure stressed in enclosure during fault arc inside switchgear is pre-sented as well. There is introduced the method based on determining stresses which are sum of tensile stresses (membrane) and deflection stresses. For tensile stresses nalysis the energy method, for unrestrainedly supported rectangular plate, was used. In the further part of the paper, the calculations and measurements results...
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublikacjaAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Effect of Porosity on the Thermo-Mechanical Behavior of Friction-Stir-Welded Spark-Plasma-Sintered Aluminum Matrix Composites with Bimodal Micro- and Nano-Sized Reinforcing Al2O3 Particles
PublikacjaThe thermo-mechanical behavior of nanosized Al2O3 particles reinforcing aluminum was analyzed in the present paper. The material was prepared by spark plasma sintering and friction stir welding. The thermal stresses affecting the composite behavior during welding were modeled through COMSOL MultiPhysics, and the results were validated by the analyses of the composites’ mechanical properties. The spark-plasma-sintered materials...
-
Deep eutectic solvent-based shaking-assisted extraction for determination of bioactive compounds from Norway spruce roots
PublikacjaPolyphenolic compounds play an essential role in plant growth, reproduction, and defense mechanisms against pathogens and environmental stresses. Extracting these compounds is the initial step in assessing phytochemical changes, where the choice of extraction method significantly influences the extracted analytes. However, due to environmental factors, analyzing numerous samples is necessary for statistically significant results,...
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublikacjaThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...