Filtry
wszystkich: 26601
wybranych: 5075
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: RETAINED AUSTENITE
-
A brief note on monotonic and fatigue fracture events investigation of thin-walled tubular austenitic steel specimens via fracture surface topography analysis (FRASTA)
PublikacjaThe main objective of this short communication is to show the fracture progression in each loading case and complement knowledge about fracture mechanisms underpinning the tensile and fatigue performance of thin-walled tubes. For this purpose, the fracture surface topography analysis (FRASTA) method was used in the thin-walled tubular austenitic stainless-steel specimens. Two cases were analyzed: monotonic tension, and uniaxial...
-
The Effect of Cryogenic Treatment on Microstructure and Mechanical Response of AISI D3 Tool Steel Punches
PublikacjaRecently, deep cryogenic treatment is performed to improve the mechanical responses (wear, hardness, fatigue, and thermal conductivity) of various steel components. Researchers have tried to evaluate the eco-friendly and nontoxic process to optimize the parameters. Cold-shearing punches used to manufacture various holes that undergo severe impact loading and wear in the metal forming process. This study concerns the effect of soaking...
-
Mechanism of Reduced Sintering Temperature of Al2O3–ZrO2 Nanocomposites Obtained by Microwave Hydrothermal Synthesis
PublikacjaA novel method to obtain Al2O3–ZrO2 nanocomposites is presented. It consists of the co-precipitation step of boehmite (AlO(OH)) and ZrO2, followed by microwave hydrothermal treatment at 270 ◦ C and 60 MPa, and by calcination at 600 ◦ C. Using this method, we obtained two nanocomposites: Al2O3–20 wt % ZrO2 and Al2O3–40 wt % ZrO2. Nanocomposites were characterized by Fourier transformed infrared spectroscopy, Raman spectroscopy,...
-
Oiled soil washing in dynamic conditions by micellar surfactants solutions and obtained effluents treatment
PublikacjaZbadano możliwość zastosowania micelarnych roztworów biosurfaktantu (JBR 425), surfaktantów syntetycznych (Rokanolu NL5, NL6, NL8) i ich mieszanin (Rokanol NL6 : JBR 425) do wymywania oleju syntetycznego z gruntu w procesie mycia gleby w warunkach dynamicznych. Micelarne roztwory Rokanolu NL6 oraz NL8 wykazały nieznacznie wyższą efektywność wymywania oleju z gruntu w porównaniu z efektywnością usuwania oleju przy pomocy roztworów...
-
Water Behavior of Aerogels Obtained from Chemically Modified Potato Starches during Hydration
Publikacja -
Three Point Bending of Laser Engineered Net Shaping (LENS) Repaired Inconel 625
Publikacja -
The Effectiveness of Using a Pretrained Deep Learning Neural Networks for Object Classification in Underwater Video
Publikacja -
Physicochemical properties of whole fruit plum powders obtained using different drying technologies
Publikacja -
Chemical Composition and Antioxidant Properties of Powders Obtained from Different Plum Juice Formulations
Publikacja -
Nuclear Magnetic Relaxation and d-Wave Pairing in a Model of a Superconductor with Non-Retarded Attraction
Publikacja -
Lyotropic liquid crystal based on zinc oxide nanoparticles obtained by microwave solvothermal synthesis
Publikacja -
Surface topography analysis based on fatigue fractures obtained with bending of the 2017A-T4 alloy
Publikacja -
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
Publikacja -
Fe-modified activated carbon obtained from biomass as a catalyst for α-pinene autoxidation
Publikacja -
Comparison of strain results at a laser weld notch obtained by numerical calculations and experimental measurements
PublikacjaIn the development of ship structures applying new materials and it’s purposeful placement play an important role. During the last years, especially in a construction of ro-ro type vessels, the usage of novel sandwich structures in cargo decks is profitable. Steel sandwich panel is an innovative solution which at a todays state of development can be used for the construction of any members not taking part in a global bending of...
-
Synthesis, structure and properties of novel poly(hydroxyurethane)s obtained by non-isocyanate route
PublikacjaNon-isocyanate polyurethanes (NIPUs) can be synthesized by polyaddition of five-membered bis(cyclic carbonate)s and primary diamines. NIPUs are an alternative for the commonly used (in the form of foams, elastomers, coatings or fibers) in the industry polyurethanes obtained using toxic and moisture sensitive diisocyanates, polyols and low-molecular weight chain extenders. The main aim of this work was to synthesize non-isocyanate...
-
Intercomparison of TEC obtained from the IRI model to the one derived from GPS measurements
PublikacjaIRI (International Reference Ionosphere) is a well-known standard of the ionosphere, but nowadays GPS permanent observations are also the base of the regional and global ionosphere models. In this paper, comparison of TEC (Total Electron Content) derived from the IRI model to the global TEC parameters derived from GPS measurements is presented. Global TEC maps show, that GPS derived ionosphere models, in opposition to the IRI,...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
GOOD HEALTH PRODUCTS AND POLYMER COMPOSITES OBTAINED WITH THE USE OF NATURAL ORIGIN MICRO- AND NANOFIBERS
PublikacjaThe aim of this work was focused on good health products and polymer composites obtained with the use of natural origin micro- and nanofibers. Many different type of the natural plants are used in the production of good health products and polymer processing like curcuma, cellulose, microalgae and others. Often are used as a antioxidants and fillers. In this work the effect of algae and cellulose as a microfillers on the chosen...
-
Seismic performance evaluation of steel buckling-restrained braced frames including SMA materials
PublikacjaThe permanent deformation of the building after seismic excitations can be determined by the Maximum Residual Interstory Drift Ratio (MR-IDR), which may be used for measuring the damage states. Low-post yield stiffness of the steel buckling-restrained braced frame (BRBF) makes this system vulnerable to large MR-IDR after a severe earthquake event. To overcome this issue, this paper investigates the seismic limit state performances...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublikacjaThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Viscoelastic properties of oil-in-water emulsions stabilized by acylpropyleneglycol emulsifiers obtained with sodium soaps
PublikacjaZbadano właściwości reologiczne emulsji typu O/W, stabilizowanych emulgatorami acylopropylenoglikolowymi. Do badań wykorzystano reometr o kontrolowanym naprężeniu ścinającym. Wykonano testy oscylacyjne tzw. ''dużej deformacji próbki'' oraz analizy typu ''pełzanie i powrót''. Stwierdzono, że właściwości lepkosprężyste emulsji determinowane były składem stosowanego emulgatora. Wszystkie badane układy emulsyjne charakteryzowały się...
-
Complementary studies of residual stress distribution of repaired power plant steam turbine casing
PublikacjaRozkład i poziom naprężeń własnych w korpusach turbin badano za pomocą efektu Barkhausena oraz metodą nawiercania otworów. Badano również twardość. Korpusy były reperowane metodą zaspawania. Wykazano, iż zastosowana technologia nie wprowadza naprężeń o poziomie zagrażającym dalszej ekploatacji korpusu.
-
Multitaper-Based Post-processing of Compact Antenna Responses Obtained in Non-anechoic Conditions
PublikacjaThe process of developing antenna structures typically involves prototype measurements. While accurate validation of far-field performance can be performed in dedicated facilities like anechoic chambers, high cost of construction and maintenance might not justify their use for teaching, or low-budget research scenarios. Non-anechoic experiments provide a cost-effective alternative, however the performance metrics obtained in such...
-
Enhancing seismic performance of buckling-restrained brace frames equipped with innovative bracing systems
PublikacjaNowadays, to improve the performance of conventional bracing systems, in which, buckling in the pressure loads is the main disadvantage, the buckling-restrained brace (BRB) is introduced as a solution. In this study, the performance of the BRB system was improved with innovative lateral-resisting systems of double-stage yield buckling-restrained brace (DYB), and a combination of DYB improved with shape memory alloy (SMA) materials...
-
Mg2+ Doping Effects on the Structural and Dielectric Properties of CaCu3Ti4O12 Ceramics Obtained by Mechanochemical Synthesis
PublikacjaIn this study, ceramic CaCu3Ti4O12 (CCTO) and CaCu3−xMgxTi4O12 solid solutions in which 0.1 ≤ x ≤ 0.5 were prepared by the mechanochemical method, realized by a high‐energy ball milling technique. The effects of the Mg2+ ion concentration and sintering time on the dielectric response in the prepared ceramics were investigated and discussed. It was demonstrated that, by the use of a sufficiently high energy of mechanochemical treatment,...
-
Recycling of Polyurethanes Containing Flame-Retardants and Polymer Waste Transformed into Flame-Retarded Polyurethanes
PublikacjaThe growing number of polyurethanes (PUs) produced every year has developed methods for their mechanical and chemical recycling which yield valuable products like substitutes for commercial polyols or flame-retardants. PUs can be produced in different shapes and forms (i.e., elastomers, flexible or rigid foams, coatings, etc.) using several different components (i.e., di- or polyisocyanates, ester- or ether-based polyols, low-molecular...
-
Conformers and hydrogen bond transformations in N-methylpiperidine betaine 2,4-dinitrophenolate crystals
Publikacja -
Preparation and characterization of activated carbons obtained from the waste materials impregnated with phosphoric acid(V)
Publikacja -
Biopolyols obtained via crude glycerol-based liquefaction of cellulose: their structural, rheological and thermal characterization
PublikacjaIn this work lignocellulose biomass liquefaction was used to produce biopolyols suitable for the manufacturing of rigid polyurethane foams. In order to better evaluate the mechanism of the process, pure cellulose was applied as a raw material. The effect of time and temperature on the effectiveness of liquefaction and the parameters of resulting biopolyols were characterized. The prepared materials were analyzed in terms of their...
-
Structural and Magnetic Properties of Co‒Mn Codoped ZnO Nanoparticles Obtained by Microwave Solvothermal Synthesis
Publikacja -
Valuable natural products from marine and freshwater macroalgae obtained from supercritical fluid extracts
Publikacja -
Analyzing sets of phylogenetic trees obtained from bayesian MCMC process using topology metrics
PublikacjaThe reconstruction of evolutionary trees is one of the primary objectives in phylogenetics. Such a tree represents historical evolutionary relationship between different species or organisms. Tree comparisons are used for multiple purposes, from unveiling the history of species to deciphering evolutionary associations amongorganisms and geographical areas.In the paper, we describe a general method for comparing hylogenetic trees....
-
CdS thin films obtained by thermal treatment of cadmium(II) complexprecursor deposited by MAPLE technique
PublikacjaCienkie warstwy kompleksu [Cd{SSi(O-But)3}(S2CNEt2)]2 zostały osadzone na podłożach Si przy użyciu techniki MAPLE (ablacja laserowa z zamrożoną matrycą). Otrzymanie warstw CdS było możliwe dzięki zastosowaniu obróbki termicznej podłoży z naniesionym prekursorem. Powierzchnia filmów była analizowana pod kątem morfologii przy użyciu mikroskopii sił atomowych (AFM) oraz pomiarów elipsometrycznych (SE).
-
Comparing N3-60 cascade exit angles obtained from tunnel measurements and numerical calculations
PublikacjaThe article compares the results of measurements performed in the aerodynamic tunnel at CUT and numerical simulation carried out for a plane cascade of N3-60 profiles. Comparing the measured and calculated results provides opportunities for assessing the range of systematic differences between simulation predictions and actual experimental results.
-
Structure and superconductivity of VN-SiO2 films obtained by thermal nitridation of sol-gel derived coatings
PublikacjaPraca prezentuje wyniki badań strukturalnych oraz właściwości nadprzewodzących cienkich warstw xVN-(100-x)SiO2, gdzie x = 90, 80, 70, 60 mol%. Warstwy zostały wykonane metodą termicznego azotowania z użyciem amoniaku cienkich warstw tlenkowych otrzymanych metodą zol-żel. Badania struktury przeprowadzono metodami XRD oraz XPS, natomiast właściwości nadprzewodzące badano metodą MMMA. Właściwości nadprzewodzące warstw zależą zarówno...
-
Structure and thermoelectric properties of Bi–Te alloys obtained by novel method of oxide substrates reduction
PublikacjaA novel method of thermoelectric materials fabrication has been developed. Oxide reagents have been melted at high temperature in air, quenched, milled to powder and reduced in hydrogen to form Bi–Te alloys. Structural and thermoelectric properties of samples have been investigated depending on initial composition and temperature of reduction process. Sample 25Bi2O3–75TeO2 reduced at 340 °C for 10 h has been found to be a p-type...
-
The influence of photointercalaction and photochromism effects on the photocatalytic properties of electrochemically obtained maze-like MoO3 microstructures
PublikacjaMolybdenum oxide (α-MoO3) thin films with oriented crystalline facets were synthesised by anodization of Mo foils. The obtained samples were exposed to UV–Vis illumination in aqueous electrolytes providing different cations. The morphology and structure of modified samples were investigated. The effect of photointercalated alkali metal cations (Li+, Na+, K+) on optical and structural properties was studied using UV–vis and Raman...
-
Biopolyols obtained via microwave-assisted liquefaction of lignin: structure, rheological, physical and thermal properties
PublikacjaThe present study examined the application of polyols obtained via microwave-assisted liquefaction of lignin in the production of rigid polyurethane foam. Lignin was liquefed in crude glycerol and 1,4-butanediol at diferent temperatures (130–170 °C), without a catalyst and using various biomass concentrations (15 and 30 wt%). The physicochemical properties, process yield, and FTIR-based identifcation of the obtained polyols were...
-
Effect of TiO2 Concentration on Microstructure and Properties of Composite Cu–Sn–TiO2 Coatings Obtained by Electrodeposition
PublikacjaIn this work, Cu–Sn–TiO2 composite coatings were electrochemically obtained from a sulfate bath containing 0–10 g/L of TiO2 nanoparticles. The effect of TiO2 particles on kinetics of cathodic electrodeposition has been studied by linear sweep voltammetry and chronopotentiometry. As compared to the Cu–Sn alloy, the Cu–Sn–TiO2 composite coatings show rougher surfaces with TiO2 agglomerates embedded in the metal matrix. The highest...
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublikacjaThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublikacjaIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
-
Validity of impedance spectra obtained by dynamic electrochemical impedance spectroscopy verified by Kramers-Kronig transformation.
PublikacjaArtykuł przedstawia weryfikację wiarygodności widm impedancyjnych otrzymanych za pomocą niedawno wprowadzonej techniki eksperymentalnej - Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej (Dynamic Electrochemical Impedance Spectroscopy, DEIS). Technika ta zakłada, że badany system jest pseudostacjonarny jeśli czas pomiaru jest odpowiednio krótki. Czas potrzebny na otrzymanie pojedynczego spektrum zależy od długości okna...
-
The Chemical and Biological Properties of Nanohydroxyapatite Coatings with Antibacterial Nanometals, Obtained in the Electrophoretic Process on the Ti13Zr13Nb Alloy
PublikacjaThe risk of an early inflammation after implantation surgery of titanium implants has caused the development of different antimicrobial measures. The present research is aimed at characterizing the effects of nanosilver and nanocopper dispersed in the nanohydroxyapatite coatings, deposited on the Ti13Zr13Nb alloy, and on the chemical and biological properties of the coatings.The one-stage deposition process was performed by the...
-
Fatigue of titanium alloy Ti6Al4V with diamond structure obtained by Laser Power Bed Fusion method
PublikacjaThis paper presents the results of fatigue tests conducted on Ti6Al4V titanium alloy with diamond structure obtained by the Laser Power Bed Fusion method. Samples used in tests were printed with porosities: 81%, 73%, 50%, 34% and near-zero porosity. Samples were subjected to cyclic tests with a constant stress amplitude. The number of cycles until sample failure was registered. Obtained fatigue test results made it possible to...
-
Anab initiostudy of the betaine anion–dipole-bound anionic state of a model zwitterion system
Publikacja -
Refined theoretical study of radiative association: Cross sections and rate constants for the formation of SiN
PublikacjaRadiative association of silicon mononitride (SiN) in its two lowest molecular electronic states is studied through quantum and classical dynamics. Special attention is paid to the behavior of the cross section at high collision energies. A modified expression for the semiclassical cross section is presented which excludes transitions to continuum states. This gives improved agreement with quantum mechanical perturbation theory...
-
Effect of urea and glycine betaine on the hydration sphere of model molecules for the surface features of proteins
PublikacjaWater properties may significantly affect protein stability. Osmolytes are compounds that intrinsically affect water in many different ways and thus can influence proteins with this type of indirect mechanism. In this study, we characterize water properties in ternary solutions: model–water–osmolyte, with two model molecules: N-methylacetamide (NMA) and dimethyl sulfoxide (DMSO) and two osmolytes: glycine betaine (TMG)and urea....
-
Comparison of selected clustering algorithms of raw data obtained by interferometric methods using artificial neural networks
Publikacja -
Accuracy analysis of 3D model obtained by photogrammetric method on the example of historic room from Wisłoujście Fortress
PublikacjaThe article presents a comparison of obtained models of a test object. Close range photogrammetry was used to obtain 3D models. As test object was used one of the rooms located in Wisłoujście Fortress in Gdańsk, Poland. Different models were obtained by using different distribution and number of reference points. Article contains analysis of differences between coordinates of control points obtained from total station measurements...