Filtry
wszystkich: 575
wybranych: 497
Wyniki wyszukiwania dla: EQUIVALENT IMPERFECTIONS
-
Evaluating the effect of different operational strategies on the carbon footprint of wastewater treatment plants – case studies from northern Poland
PublikacjaNowadays, low greenhouse gas (GHG) emission is expected at wastewater treatment plants (WWTPs). However, emission quantification and evaluation still faces difficulties related to data availability and uncertainty. The objective of this study was to perform carbon footprint (CF) analysis for two municipal WWTPs located in northern Poland. Slupsk WWTP is a large biological nutrient removal (BNR) facility (250,000 PE) which benefits...
-
Measurements of OF QoS/QoE parameters for media streaming in a PMIPv6 TESTBED WITH 802.11 b/g/n WLANs
PublikacjaA growing number of mobile devices and the increasing popularity of multimedia services result in a new challenge of providing mobility in access networks. The paper describes experimental research on media (audio and video) streaming in a mobile IEEE 802.11 b/g/n environment realizing network-based mobility. It is an approach to mobility that requires little or no modification of the mobile terminal. Assessment of relevant parameters...
-
STABILITY AND LOAD BEARING CAPACITY OF A BARS WITH BUILT UP CROSS SECTION AND ELASTIC SUPPORTS
PublikacjaThe present paper is devoted to the numerical analysis and experimental tests of compressed bars with built–up cross section which are commonly used as a top chord of the roof trusses. The significant impact on carrying capacity for that kind of elements in case of out-of-plane buckling is appropriate choice of battens which are used to provide interaction between separate members. Linear buckling analysis results and nonlinear static...
-
NON-LINE ANALYSIS OF STIFFNESS IN COMPRESSION CONDITIONS
PublikacjaThe analyzes were aimed at demonstrating the influence of parameters describing the deformation of the structure on the uncertainty of critical force, and the impact of technological imperfections on stress uncertainty in compression conditions. In a linear buckling analysis, the problem is considered only for the initial, permanent state of the stiffness matrix. In the case of demonstrating the influence of initial deformations...
-
Axial capacity of steel built-up battened columns
PublikacjaThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Selected issues related to the toxicity of ionic liquids and deep eutectic solvents—a review
PublikacjaGreen Chemistry plays a more and more important role in implementing rules of sustainable development to prevent environmental pollution caused by technological processes, while simultaneously increasing the production yield. Ionic liquids (ILs) and deep eutectic solvents (DESs) constitute a very broad group of substances. Apart from many imperfections, ILs and DESs have been the most promising discoveries in the world of Green...
-
Extending loophole-free nonlocal correlations to arbitrarily large distances
PublikacjaQuantum theory allows spatially separated observers to share nonlocal correlations, which enable them to accomplish classically inconceivable information processing and cryptographic feats. However, the distances over which nonlocal correlations can be realized remain severely limited due to their high fragility to noise and high threshold detection efficiencies. To enable loophole- free nonlocality across large distances, we introduce...
-
RÓWNOWAŻNOŚĆ METOD POMIAROWYCH CIĄGŁYCH I ODNIESIENIA STOSOWANYCH DO OZNACZANIA PM2,5
PublikacjaW pracy przedstawiono wyniki testu terenowego przeprowadzonego na terenie województwa pomorskiego w okresie od 01-01-2013 do 31-12-2013 w celu wykazania równoważności wyników stężeń pyłu zawieszonego PM2,5 uzyskanych za pomocą analizatora automatycznego BAM 1020 w stosunku do wyników uzyskanych za pomocą wagowej metody odniesienia. Przedstawiono sposób określania równoważności wyników uzyskanych za pomocą analizatora i szacowania...
-
Discrete Green's function approach to disjoint domain simulations in 3D FDTD method
PublikacjaA discrete Green’s function (DGF) approach to couple 3D FDTD subdomains is developed. The total-field/scattered-field subdomains are simulated using the explicit FDTD method whilst interaction between them is computed as a convolution of the DGF with equivalent current sources measured over Huygens surfaces. In the developed method, the DGF waveforms are truncated using the Hann’s window. The error varies in the range -65 to -40...
-
FEM simulation of laminate failure in the three point bending
PublikacjaThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
High-precision bearing estimation for active sonar with cylindrical array performed by interpolated array transformation
PublikacjaThe article presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. The antenna’s non-linear shape and the resulting non-uniform sampling of the signal in space, mean that known methods of high-resolution spectral analysis cannot be used. In order to apply an algorithm from this group, a linear virtual antenna must be produced. The paper presents a technique of mapping a cylindrical...
-
Modal properties identification of a novel sandwich footbridge – Comparison of measured dynamic response and FEA
PublikacjaA modern sandwich composite footbridge made of high-tech materials, being an example of practical application of laminated composites in civil engineering, is presented. The in situ non-destructive testing of the footbridge, aiming to identify modal properties and pedestrian comfort, is described. The measured eigenmodes and eigenfrequencies are compared with numerically estimated values. Finite element analyses of the footbridge...
-
All Nonclassical Correlations Can Be Activated into Distillable Entanglement
PublikacjaWe devise a protocol in which general nonclassical multipartite correlations produce a physically relevant effect, leading to the creation of bipartite entanglement. In particular, we show that the relative entropy of quantumness, which measures all nonclassical correlations among subsystems of a quantum system, is equivalent to and can be operationally interpreted as the minimum distillable entanglement generated between the system...
-
Impedance monitoring of corrosion degradation of plasma electrolytic oxidation coatings (PEO) on magnesium alloy
PublikacjaImpedance technique based on continuous multisinusoidal current perturbation was used to explain degradation process of plasma electrolytic oxidation coatings (PEO) on magnesium alloy. An obtained impedance spectrum was fitted by electrical equivalent circuit to describe properties of conversion layer on magnesium alloy. Additionally, galvanostatic mode maintained during experiment, with DC current equal to zero, allowed to achieve...
-
A novel sandwich footbridge - Practical application of laminated composites in bridge design and in situ measurements of static response
PublikacjaA novel sandwich composite footbridge is presented in the paper, as an example of practical application of laminated composites in civil engineering. The in situ static load tests of the footbridge before its acceptation for exploitation are shown and discussed. The results are compared with the corresponding ones from a numerical equivalent single layer model of the sandwich structure created within the framework of finite element...
-
Modelling and analysis of medium frequency transformers for power converters
PublikacjaThe evolutions in power systems and electric vehicles, related to the economic opportunities and the environmental issues, bring the need of high power galvanically isolated DC-DC converter. The medium frequency transformer (MFT) is one of its key components, enabled by the increasing switching frequency of modern power semiconductors like silicon carbide transistors or diodes. The increased operating frequency offers small...
-
Influence of vacuum sublimation deposited metal layer thickness on metrological parameters of the amperometric gas sensor with Nafion membrane
PublikacjaThe paper presents the results of investigation on an influence of vacuum sublimation deposited platinum layer thickness on the signal, sensitivity and response time of a prototype of sulphur dioxide sensor with Nafion membrane. The working electrode was made by vacuum sublimation deposition of platinum on a surface of Nafion membrane. Pt layers deposited changed an initial structure of Nafion membrane and that phenomenon was utilized...
-
Rapid EM-Driven Design of Compact RF Circuits By Means of Nested Space Mapping
PublikacjaA methodology for rapid design of RF circuits constituted by compact microstrip resonant-cells (CMRCs) is presented. Our approach exploits nested space mapping (NSM) technology, where the inner SM layer is used to correct the equivalent circuit model at the CMRC level, whereas the outer layer enhances the coarse model of the entire structure under design. We demonstrate that NSM dramatically improves performance of surrogate-based...
-
Finding small-width connected path decompositions in polynomial time
PublikacjaA connected path decomposition of a simple graph $G$ is a path decomposition $(X_1,\ldots,X_l)$ such that the subgraph of $G$ induced by $X_1\cup\cdots\cup X_i$ is connected for each $i\in\{1,\ldots,l\}$. The connected pathwidth of $G$ is then the minimum width over all connected path decompositions of $G$. We prove that for each fixed $k$, the connected pathwidth of any input graph can be computed in polynomial-time. This answers...
-
Estimators of covariance matrices in Msplit(q) estimation
PublikacjaThis paper proposes methods for the determination of covariance matrices of Msplit(q) estimators. The solutions presented here allow Msplit(q) estimation to be supplemented by the operations from the domain of accuracy analysis (especially that concerning estimators of parameters). Theoretical forms of covariance matrices of Msplit(q) estimators were established using the empirical influence functions and the equivalent covariance...
-
Large thermo-elastic displacement and stability FEM analysis of multilayered plates and shells
PublikacjaThe paper concerns the load capacity analysis of thermally loaded multilayered plates and shells. The multilayered body is treated as an equivalent single layer whose kinematics is consistent with first order shear deformation theory. The authors focus on the thermo-elastic stability problem of the thin-walled structures. The equilibrium paths are traced with the use of Riks-Wempner-Ramm algorithm. By making use of the Tsai-Wu...
-
Stability of roof trusses stiffened by trapezoidal sheeting and purlins
PublikacjaIn the article linear buckling analysis of a set of steel trusses braced by purlins and trapezoidal sheeting are conducted. The buckling load factor due to the height of a corrugated sheeting profile is investigated in parametric studies. The minimal height of trapezoidal sheeting required for preventing the sheeting and chords of the trusses against the buckling is obtained. Two groups of models are considered: “axial” model as...
-
Evaluation of Temperature Influence on Electrochemical Processes Occurring in a Lithium-Ion Supercapacitor with the Use of Dynamic Electrochemical Impedance Spectroscopy
PublikacjaIn order to obtain the full impedance characteristics of a lithium-ion capacitor as a function of temperature, the authors proposed the use of dynamic electrochemical impedance spectroscopy. Impedance tests were carried out under wide range of dynamic temperature changes for lithium-ion supercapacitors. Significant differences in electrochemical processes were observed as a result of working temperature. Moreover, the quality of...
-
Application of probabilistic tools to extend load test design of bridges prior to opening
PublikacjaLoad tests of bridges are widely performed in a large number of countries. Deterministic comparison of measurement results to the theoretical, FEM (finite element method)-based outcomes with possible further calibration is mostly applied. Sometimes, the data collected in the tests are also used to calibrate the reliability factors of bridge structures or their components. This work proposes to complement the stage of the load test...
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublikacjaFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Static load test on concrete pile – instrumentation and results interpretation
PublikacjaFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Compact Quasi-Elliptic-Type Inline Waveguide Bandpass Filters With Nonlinear Frequency-Variant Couplings
PublikacjaThis work presents the design techniques to synthesize a class of compact inline quasi-elliptic-type waveguide cavity bandpass filters based on novel nonlinear frequency-variant couplings (NFVCs). These highly dispersive frequency-variant couplings (FVCs) are realized by means of a pair of partial-height posts that are placed at the junctions between every two cavity resonators. Each NFVC produces a transmission pole in between...
-
The correlation of fractal dimension to fracture surface slope for fatigue crack initiation analysis under bending-torsion loading in high-strength steels
PublikacjaIn this study, the fractal dimension of fatigue fracture surfaces is investigated in order to find an alternative failure loading indicator. Some of many metrological factors are generalized by reducing the fracture surface structure to one factor and develop an entire fracture surface procedure by analyzing the impact of surface slope and calculation resolution. Three notched geometries are studied under cyclic bending-torsion:...
-
Leveraging food waste for electricity: A low-carbon approach in energy sector for mitigating climate change and achieving net zero emission in Hong Kong (China)
PublikacjaIn recent years, food waste has been a global concern that contributes to climate change. To deal with the rising impacts of climate change, in Hong Kong, food waste is converted into electricity in the framework of low-carbon approach. This work provides an overview of the conversion of food waste into electricity to achieve carbon neutrality. The production of methane and electricity from waste-to-energy (WTE) conversion are...
-
Design of novel highly sensitive sensors for crack detection in metal surfaces: theoretical foundation and experimental validation
PublikacjaThe application of different types of microwave resonators for sensing cracks in metallic structures has been subject of many studies. While most studies have been focused on improving the sensitivity of planar crack sensors, the theoretical foundation of the topic has not been treated in much detail. The major objective of this study is to perform an exhaustive study of the principles and theoretical foundations for crack sensing...
-
On asymptotic periodicity of kernel double Markovian operators
PublikacjaIt is proved that a kernel, doubly Markovian operator T is asymptotically periodic if and only if its deterministic σ-field Σd(T)(equivalently Σd(T∗)) is finite. It follows that kernel doubly Markovian operator T is asymptotically periodic if and only if T∗ is asymptotically periodic.
-
Average Size of a Suffix Tree for Markov Sources
PublikacjaWe study a suffix tree built from a sequence generated by a Markovian source. Such sources are more realistic probabilistic models for text generation, data compression, molecular applications, and so forth. We prove that the average size of such a suffix tree is asymptotically equivalent to the average size of a trie built over n independentsequences from the same Markovian source. This equivalenceis only known for memoryless...
-
Implementation of DEIS for reliable fault monitoring and detection in PEMFC single cells and stacks
PublikacjaDynamic Electrochemical Impedance Spectroscopy (DEIS) was presented as novel method for diagnostic and monitoring of PEMFC stack and single cells operation. Impedance characteristics were obtained simultaneously with current - voltage characteristics for stack and each individual cell. Impedance measurements were performed in galvanodynamic mode. It allowed to compare performance of each cell and identification of faulty cell operation...
-
Influence of Thermal Decomposition of Wood and Wood-Based Materials on the State of the Atmospheric Air. Emissions of Toxic Compounds and Greenhouse Gases
PublikacjaThis paper presents the energy characteristics of wood and wood-based materials in the form of commercially available pellets, furniture board (MDF) and OSB. Toxicometric indices were determined for gaseous destructs arising from thermal decomposition and combustion of the materials studied. The paper proves that combustion conditions are crucial in terms of toxic destructive emissions. It has been shown that the combustion of...
-
Reducing Air Pollutant Emissions from the Residential Sector by Switching to Alternative Energy Sources in Single-Family Homes
PublikacjaThe paper discusses a scenario for adapting residential buildings to the requirements of the EU climate and energy package. It analyzes the option of reducing pollutant emissions to ambient air by switching to alternative energy sources in a typical single-family residential building. The most common sources of energy in central heating and ventilation systems and water heating systems were compared, and the analyzed energy carriers...
-
Thermo-elastic non-linear analysis of multilayered plates and shells
PublikacjaGeometrically nonlinear FEM analysis of multilayered composite plates and shells is performed in order to resolve the stability problem of the structures being under the influence of temperature field. The Riks-Wempner-Ramm algorithm with a specially modified multi-choice unloading condition has been implemented in authors’ numerical code. As the representation of multilayered medium the Equivalent Single Layer approach with the...
-
Miniaturized bandpass substrate integrated waveguide filter with frequency-dependent coupling realized using asymmetric GCPW discontinuity
PublikacjaAn asymmetric GCPW discontinuity is proposed to provide frequency-dependent coupling in microwave bandpass filters. Wider and narrow sections introduce, respectively, the capacitive and inductive component to the equivalent circuit representing coupling. By selecting the dimensions of the discontinuity and width of the inductive window in substrate integrated waveguide, an additional transmission zero can be introduced at prescribed...
-
Rapid multi-objective simulation-driven design of compact microwave circuits
PublikacjaA methodology for rapid multi-objective design of compact microwave circuits is proposed. Our approach exploits point-by-point Pareto set identification using surrogate-based optimization techniques, auxiliary equivalent circuit models, and space mapping as the major model correction method. The proposed technique is illustrated and validated through the design of a compact rat-race coupler. A set of ten designs being trade-offs...
-
Równoważność metod pomiarowych ciągłych i odniesienia stosowanych do oznaczania pm10
PublikacjaW pracy przedstawiono wyniki testu terenowego przeprowadzonego na terenie Gdańska w okresie od 01-01-2010 do 31-12-2010 i od 01-01-2011 do 31-12-2011 w celu wykazania równoważności wskazań analizatora Eberline FH 62-1 w stosunku do wagowej metody odniesienia. Przedyskutowano występowanie różnic wskazań wartości stężeń pyłu PM10 w zależności od pory roku dla obu metod pomiarowych. Przedstawiono sposób określania równoważności tych...
-
Noise measurements on low noise pavements - problems with inhomogeneity of wearing course
PublikacjaDuring the last several years, when performing numerous CPX noise measurements on low noise pavements,significant inhomogeneity of the wearing course was observed in numerous cases. Similar problems were almost not existing regarding to the dense pavements.In general three main reasons of inhomogeneity can be defined. The first one are imperfections in technology of production of a asphalt mix or/and errors made already during...
-
Optimizing the computation of a parallel 3D finite difference algorithm for graphics processing units
PublikacjaThis paper explores the possibilities of using a graphics processing unit for complex 3D finite difference computation via MUSTA‐FORCE and WENO algorithms. We propose a novel algorithm based on the new properties of CUDA surface memory optimized for 2D spatial locality and compare it with 3D stencil computations carried out via shared memory, which is currently considered to be the best approach. A case study was performed for...
-
Impedance of cation-coupled electron transfer reaction: Theoretical description of one pathway process
PublikacjaIt has been assumed that cation electron coupled charge transfer can be conducted in accordance with two mutually coupled reactions. Using a differential method an expression was introduced which describes the impedance of a cation electron coupled transfer reaction. Also, an electrical equivalent circuit has been defined. The total faradaic impedance is the sum of electron transfer impedance and cation transfer impedance. Issues...
-
Errors in the analysis of series resonant inverter/converter assuming sinusoidal waveforms of voltage and current
PublikacjaIn this paper the theory and simulation results of the series resonant inverter / converter are presented. In this work the authors carried out a detailed comparative analysis of results obtained using the method of AC analysis in the steady state for the first harmonic with the results of computer simulation. The AC analysis under certain conditions can lead to errors disqualifying this method. In particular, these errors appear...
-
Analiza płyt laminowanych z zastosowaniem zastępczych modeli jednowarstwowych
PublikacjaW pracy przedstawiono analizę porównawczą wybranych modeli obliczeniowych płyt warstwowych, zgodnych z koncepcjš zastępczego modelu jednowarstwowego (Equivalent Single Layer - ESL). Rozważono trzy modele bazujące na teorii ścinania pierwszego rzędu: dwa modele autorskie oraz model paneli laminowanych dostępny w systemie MSC/NASTRAN. Zróżnicowanie modeli wynika z odmiennego podejścia do tzw. korekty ścinania. Przeprowadzono obliczenia...
-
Green, simple analytical method for total biogenic amines content determination in wine using spectrophotometry
PublikacjaA simple, green and equitable procedure for total biogenic amines (BAs) content determination was developed. The scientific novelty lies in the use of commercially available S 0378 dye, the reaction of which with BAs results in a colour change of the solution. Sample preparation and analysis were simplified to make the method suitable for routine analyses even in resource-scarce settings. The optimization of the method was carried...
-
Excitation of Circularly Polarized Wave via Single-Feed Metasurface-Integrated Compact Antenna for Internet of Things
PublikacjaA compact circularly polarized (CP) quasi-omnidirectional antenna is introduced for internet of things (IoT). The structure consists of two components implemented on FR-4 substrates, and sep-arated by an air gap: one printed with a rectangular patch fed through a matching network, and another with a metasurface and a ground plane. Two different methods for impedance matching are employed. An equivalent circuit model of the antenna...
-
In Situ Verification of Numerical Model of Water Hammer in Slurries
PublikacjaThis paper presents a numerical model of transient flow in a pressure slurry pipeline network with verification based on in situ measurements. The model, primarily verified in laboratory conditions, has been extended and applied to the case of a large and complex slurry pipeline network in Poland. In the model, the equivalent density concept was applied. In situ experiments were performed for various unsteady flow episodes, caused by...
-
DETERMINANTS OF INLAND NAVIGATION ON THE VISTULA FROM WARSAW TO GDAŃSK
PublikacjaWaterborne transport is the cheapest, the safest and the least harmful to the natural environment. Restoring regular waterway cargo transport will require revitalisation of the existing trans-shipment and logistics infrastructure for commercial inland ports and building new. Transport policy makers must remember that waterborne transport is the most ecological type of transport. It produces only 10% of the gases emitted to the...
-
Nested Space Mapping Technology for Expedite EM-driven Design of Compact RF/microwave Components
PublikacjaA robust simulation-driven methodology for rapid and reliable design of RF/microwave circuits comprising compact microstrip resonant cells (CMRCs) is presented. We introduce a nested space mapping (NSM) technology, in which the inner space mapping layer is utilized to improve the generalization capabilities of the equivalent circuit model corresponding to a constitutive element of the circuit under consideration. The outer layer...
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship and offshore structures. Part II: Load - pit crack interaction
PublikacjaIn the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation and growth rate, whose presence has been questioned by some authors but accepted by most of them. Influence of pit walls roughness on fatigue life of a plate suffering pit corrosion and presence of so called "non damaging" pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction...