Filtry
wszystkich: 2467
wybranych: 663
-
Katalog
- Publikacje 663 wyników po odfiltrowaniu
- Czasopisma 2 wyników po odfiltrowaniu
- Osoby 4 wyników po odfiltrowaniu
- Wynalazki 1 wyników po odfiltrowaniu
- Laboratoria 3 wyników po odfiltrowaniu
- Aparatura Badawcza 2 wyników po odfiltrowaniu
- Kursy Online 1 wyników po odfiltrowaniu
- Wydarzenia 2 wyników po odfiltrowaniu
- Dane Badawcze 1789 wyników po odfiltrowaniu
Filtry wybranego katalogu
Wyniki wyszukiwania dla: qm/mm
-
Chip geometry while sawing frozen wood.
PublikacjaW pracy przedstawiono analizę geometrii wiórów zebranych podczas przecierania pryzm sosnowych o temperaturach -5 st. C, -20 st. C, + 18 st. C na pilarce ramowej przecieranych za pomocą cienkich pił. Analizowano rozkład wiórów w funkcji ich wymiarów podłużnych oraz pola powierzchni. W badaniach wykorzystywano kamere cyfrową, a obrazy z niej uzyskane obrabiano za pomoca oprogramowania opracowanego w srodowisku LabView. W widmach...
-
UWB-Based Indoor Navigation in a Flexible Manufacturing System Using a Custom Quadrotor UAV
PublikacjaA novel solution for indoor navigation of a transportation drone in flexible manufacturing is presented in this paper. To address the challenges of accurate and robust drone navigation in occluded environments, an ultra-wideband (UWB) navigation system has been integrated with a commercially available open source control platform. The system offers high accuracy (± 20 mm), low power consumption, resistance to electronic interference,...
-
Development and application of asphalt binder relaxation test in different dynamic shear rheometers
PublikacjaIn this study, a novel relaxation test is proposed to evaluate asphalt binder low temperature properties using a Dynamic Shear Rheometer (DSR) with parallel plates of 4 mm in diameter. Three rheometers from three different manufacturers are used to analyze seven asphalt binders. Different material parameters are derived which are useful to evaluate and discriminate different asphalt binders. Test results of all three instruments...
-
Aqueous Molybdate Provides Effective Corrosion Inhibition of WE43 Magnesium Alloy in Sodium Chloride Solutions
PublikacjaCorrosion and corrosion inhibition of WE43 magnesium alloy were investigated in NaCl solutions containing different amounts of sodium molybdate. Electrochemical, microscopic, and spectroscopic experiments were utilized to examine the mechanism of corrosion inhibition by molybdates. Electrochemical data showed that Na2MoO4 inhibitor provides reliable inhibition at concentrations at and above 100 mM. Raman and XPS spectroscopy demonstrated...
-
N-phosphonomethylglycine utilization by the psychrotolerant yeast Solicoccozyma terricola M 3.1.4.
PublikacjaSolicoccozymaterricolaM 3.1.4., the yeast strain isolated from soil sample from blueberry cultivation in MiedzyrzecPodlaski in Poland, is capable to split of phosphorus to nitrogen and nitrogen to carbon bonds inN-phosphono-methylglycine (PMG, glyphosate). The biodegradation process proceeds in the phosphate-independent manner. Itis the first example of a psychrotolerant yeast strain able to degrade PMGviaCeN bond cleavage accompanied...
-
Thermal Analysis Of Hybrid Microchannel-Microjet Heat Exchanger
PublikacjaThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When laminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
-
Phosphate and Thiophosphate Biphenyl Analogs as Steroid Sulfatase Inhibitors
PublikacjaIn the present work, we report convenient methods for the synthesis and biological evaluation of phosphate and thiophosphate biphenyl derivatives exhibiting steroid sulfatase (STS) activity. The described synthesis is based on straightforward preparation of biphenyl-4-ol and 40-hydroxybiphenyl- 4-carboxylic acid ethyl ester modified with various phosphate or thiophosphate moieties. The inhibitory effects of these compounds were...
-
Stability and limit load analysis of a cold-formed channel section column
PublikacjaThe paper presents stability and limit load analysis of a steel column 1440 mm high of a cold-formed channel section, subjected to a combination of compression and bending. Experimental results were compared to the resistance of a code procedure and to the outcome of numerical non-linear analysis. Comparison was made of numerical solutions by means of static (Riks) and dynamic (Explicit and Implicit) methods. Perfectly elastic...
-
COMPUTER ANALYSIS OF HYDRAULIC CONDITIONS IN A SANITARY CHAMBER
PublikacjaThis paper presents analysis of hydraulic conditions of sewage flow down the slipway (ramp) in the collecting sanitary chamber connecting 3 collectors on the inlet: ⌀600, ⌀800 and ⌀1400 and one on the outlet ⌀1600 mm, with a maximum difference of elevation 5 m. The mathematical model has been made and hydraulic calculations were carried out in steady flow conditions. Then wastewater surface elevation, energy grade line elevation,...
-
Peculiarities of measurement uncertainty evaluation at calibrating a ring gauge
PublikacjaExample S13 from EA-4/02 M:2013 “Calibration of a ring gauge with a nominal diameter of 90 mm” is analyzed. The report uses the kurtosis method and the law of propagation of expanded uncertainty developed by the authors to the expanded uncertainty evaluation. It is shown that the introduction of a coaxiality correction for the ring gauge and the measuring axis of the comparator leads to the need to estimate its standard measurement...
-
Teledetekcyjne badanie konstrukcyjnych elementów żelbetowych z użyciem naziemnego skaningu laserowego
PublikacjaWspółczesna technologia naziemnego skaningu laserowego (TLS) z użyciem skanerów geodezyjnych o zasięgu większym niż 50 metrów pozwala na pomiar geometrii elementów konstrukcyjnych z dokładnością bliską 1 mm. Autorzy, w oparciu o badania laboratoryjne i doświadczenia własne, prezentują rozwiązanie pozwalające na wstępną ocenę belek żelbetowych jako podstawowych elementów konstrukcyjnych budowli typu mosty, wiadukty, budynki wielkopowierzchniowe. Przedmiotem...
-
A new method of current limitation. Nowa metoda ograniczania prądu.
PublikacjaZaprezentowano nowa ideę hybrydowego, bezstykowego ogranicznika prądów zwarciowych oraz możliwości jego aplikacji. W ograniczniku tym zastąpiono łącznik zestykowy bezpiecznikiem o ultra krótkim topiku, dzięki czemu uniknięto niedogodności związanych z napędem występujących w klasycznych łącznikach hybrydowych. Rolą bezpiecznika w tym nowym zestawie jest wyłącznie zadziałanie w warunkach zwarciowych, a po przejęciu prądu...
-
Modelling of axial magnetic field effect on electric arc in ablation capillaries
PublikacjaBadano wpływ osiowego pola magnetycznego na łuk elektryczny w kapilarze ablacyjnej o średnicy do 3 mm. Wyniki porównywano z kapilarą ceramiczną. Łuk zasilany był z baterii kondensatorów prądem do około 1200 A. Stosowano pole magnetyczne wolnozmienne oraz wysokoczęstotliwościowe o indukcji do 10 T. Stwierdzono nawet 3-krotny wzrost napięcia łukowego pod wpływem osiowego pola magnetycznego w kapilarze gazującej, przy braku reakcji...
-
Nonlinear Impedance as Possible Result of Ion-Polaron Interaction in Cu2O-Al2O3-SiO2 Glass
PublikacjaNonlinear a.c. impedance measurements were performed in Cu2O-Al2O3-SiO2 glass in wide frequency range. The obtained results shows that a large nonlinearity in the impedance signal is observed at moderate electric fields of an order 1V/mm. The contents of the third harmonics reaches about 10% and strongly depends on temperature and frequency. The investigated glass exhibits mixed electronic-ionic conductivity. Electronic conduction...
-
Photocatalytic activity and surface properties of carbon-doped titanium dioxide
PublikacjaTiO2 domieszkowany węglem otrzymano poprzez hydrolizę izopropanolanu tytanu(IV) i kalcynację w 350ºC w atmosferze powietrza przez 2h. Przeprowadzone badania wykazały, że fenol (0.21 mM) jest efektywnie degradowany w fazie wodnej, w obecności otrzymanego fotokatalizatora oraz światła z zakresu widzialnego (λ>400 nm). Pole powierzchni właściwej otrzymanego C-TiO2 wynosiło około 127 m2/g, fotokatalizator absorbuje światło z zakresu...
-
Experimental and numerical analysis of streamwise vortex generator for subsonic flow
PublikacjaW pracy przedstawiono porównanie wyników obliczeń numerycznych dwoma kodami (FLUENT i SPARC) na tle badań eksperymentalnych generatora wirów wzdłużnych. Przedstawiono wyniki dla liczb Macha przepływu głównego 0.3 i 0.8. Porównano ciśnienie całkowite w dwóch przekrojach za otworem przez który realizowany jest wydmuch. Przedstawiono strukturę wiru wzdłużnego uzyskaną dla obu programów. Średnica otworu jetu jest równa 1mm, co odpowiada...
-
Identification and characterization of single-stranded DNA-binding protein from the facultative psychrophilic bacteria Pseudoalteromonas haloplanktis
PublikacjaSingle-stranded DNA-binding protein (SSB) plays an important role in DNA metabolism such as DNAreplication, repair, and recombination, and is essential for cell survival. This study reports on the ssb-likegene cloning, gene expression and characterization of a single-stranded DNA-binding protein of Pseudoal-teromonas haloplanktis (PhaSSB) and is the first report of such a protein from psychrophilic microorganism.PhaSSB possesses...
-
Experimental and numerical study of thermal and electrical potential of BIPV/T collector in the form of air-cooled photovoltaic roof tile
PublikacjaAmong renewable energy sources, Building-Integrated Photovoltaic/Thermal (BIPV/T) systems are gaining increasing interest. To improve their economic competitiveness, technologies that increase their efficiency are searched for. The paper is devoted to evaluating the impact of various air-cooling configurations on the thermal and electrical performance of a photovoltaic roof tile. A numerical model of the own experimental system...
-
Mechanical and radiation shielding properties of concrete reinforced with boron--basalt fibers using Digital Image Correlation and X--ray micro--computed tomography
PublikacjaThe paper presents experimental investigations of the radiation shielding, mechanical and fracture properties of concrete reinforced with 5 kg/m3 of novel basalt fibers infused with boron oxide (BBF). However, further studies concerning other dosages i.e. 1 kg/m3, 10 kg/m3, 15 kg/m3 and 20 kg/m3 are currently carried out. Experiments with neutron source revealed that addition of BBF as a dispersed concrete reinforcement could improve...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Using differential pressure sensor to measure nitrous oxide level in a tank
PublikacjaA method for measuring the level of liquid nitrous oxide oxidizer in a hybrid rocket motor oxidizer tank is proposed. Presented approach is more accurate than the most commonly used method of this measurement, which employs weighting of the whole sounding rocket or an oxidizer tank. In our solution we use a differential pressure sensor to measure the change of pressure at the bottom of an oxidizer tank in comparison to the pressure...
-
Near-Field Wireless Sensing of Plastics and Papers Using Frugal Peel-Off Passive Tag
PublikacjaThis article presents a novel frugal approach of testing plastics and papers using a near-field microwave sensing technique with a peel-off tag. The proposed sensing technique involves two electrical entities: the sensor, which may be regarded as a reader, and a disposable tag. The reader is a modified design of a gap-coupled microstrip line (GCML) sensor, while the passive tag is a standard double-ring complementary split-ring...
-
Investigation of Acoustic Properties of Poroelastic Asphalt Mixtures in Laboratory and Field Conditions
PublikacjaMeasures for the improvement of acoustic conditions in the vicinity of roads include the construction of pavement structures with low-noise surfaces with optimal macrotexture and the highest possible sound absorption coefficient. Laboratory evaluation of acoustic properties of a designed asphalt mixture before its placement in the pavement is a good solution. Currently, the most popular method for the determination of the sound...
-
The occurrence of heavy metals and metal-resistant bacteria in water and bottom sediments of the Straszyn reservoir (Poland)
PublikacjaThe aim of this study is investigate the distribution of selected heavy metals (zinc, copper, lead, cadmium) and metal-resistant bacteria in water and bottom sediments of drinking water reservoir for Gdańsk (Poland). The research area - Straszyn Lake is a dam reservoir on Radunia river, of the total volume of 3 mln m3. Sediment and water sampling took place between May and October 2013 (eight series). Regarding metal concentration...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublikacjaThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
High temperature drying of beech with content of tension wood
PublikacjaThe presented artcle is focused on comparison of tension and normal wood of beech (Fagus sylvatica L.) in a high-temperature drying process. Samples of 26 mm thickness were selected from sapwood zone with different angle of growth rings. The article evaluated properties of tension and normal wood before and after drying process. Properties which are monitored were moisture, moisture gradients, covering tests, colour changes and...
-
A new hybrid method for analysis of scattering from arbitrary configuration of cylindrical objects
PublikacjaArtykuł opisuje nową hybrydową metodę analizy rozpraszania fali elektromagnetycznej od obiektów cylindrycznych o dowolnym przekroju poprzecznym. W prezentowanym podejściu każdy obiekt jest traktowany jako efektywny cylinder o przekroju kołowym, opisany przez macierz impedancyjną. W celu uzyskania owej macierzy zastosowano połączenie metod różnic skończonych w dziedzinie częstotliwości (FDFD) i dopasowania rodzajów (MM). W celu...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublikacjaThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL-MICROJET TEST PROBE
PublikacjaThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
-
Shell model of multiple-row moment I-section end-plate joint
PublikacjaThe paper deals with a problem of application of shell elements in the models of multiple-row moment end-plate connections. The extended connection of I-section with a cross-section W760x265x220 made of steel S355 was analyzed. Comparison analysis of FEM, complex volume and shell models has been done. Three cases with different end-plate thickness: 14, 18 and 36 mm were analyzed and compared with the reference results. Comparison...
-
Analiza wezbrania rzeki Kaczej w Gdyni po opadzie z 14 lipca 2016 roku
PublikacjaW połowie lipca 2016 r. w Trójmieście, zanotowano opad atmosferyczny o sumie przekraczającej 150 mm. Opadom deszczu od godzin popołudniowych dnia 14 lipca do godzin rannych 15 lipca towarzyszył okresami bardzo silny i gwałtowny wiatr początkowo z kierunku północno-wschodniego następnie z kierunku północno-zachodniego. Opisana sytuacja hydro-meteorologiczna spowodowała znaczne wezbrania w rzekach i potokach rejonu Zatoki Gdańskiej,...
-
Wpływ rozwinięcia powierzchni na przenoszenie ciepła podczas wrzenia R 22 wewnątrz rur
PublikacjaPrzedstawiono wyniki badań przejmowania ciepła i spadku ciśnienia podczas wrzenia czynnika chłodniczego R 22 w przepływie wewnątrz rur poziomych. Badanymi rurami były: rura miedziana niskożebrowana typu "micro-fin", rura ze stali nierdzewnej śrubowoformowana, a także miedziana i stalowa rura gładka. Średnica zewnętrzna rur wynosiła 10 mm. Eksperymenty prowadzono przy temperaturze nasycenia 0 stopni C, stopniu suchości na wlocie...
-
Miniaturised analytical procedure of determining polycyclic aromatic hydrocarbons and polychlorinated biphenyls in bottom sediments
PublikacjaOpisano metodę oznaczania bardzo niskich stężeń polichlorowanych bifenyli w obecności wysokich zawartości wielopierścieniowych węglowodorów aromatycznych. Analizie techniką GC-MS poddawany jest ekstrakt z 1 g próbki osadu. Jako standardy wewnętrzne zastosowano Naftalen-d8, benzo[a]antracen-d12 i PCB 209. Średni odzysk standardów przedstawiał się następująco: 65, 55 i 60% odpowiednio. Do izolacji frakcji PCB stosowano niekomercyjne...
-
Examination method of the effect of the incidence angle of laser beam on distance measurement accuracy to surfaces with different colour and roughness
PublikacjaInterest in the influence of the incidence angle of a laser beam to distance measurements can be seen in many areas of science and technology: geodesy, glaciology, archaeology, machine automation, and others. This paper presents results of measurements of the effect of the incidence angle of a laser beam to distance measurements to the surfaces of different colour and roughness by Topcon's electro-optical total station with an...
-
Selected problems concerning strength of a floating dock with roof
PublikacjaW pracy przedstawiono modele i wyniki analizy wytrzymałości konstrukcji zadaszonego doku pływającego. Obliczono, że ścianki wiązarów zadaszenia, aby mogły przenieść obciążenia środowiskowe, muszą mieć grubość 24 mm. Ciężkie przesuwne segmenty zadaszenia generują w dennikach pontonu doku naprężenia sięgające 25% wartości dopuszczalnych. Wytężenie konstrukcji pontonu doku i podbudowy, obciążonych ciężarem zadaszenia i dokowanego...
-
Optoelektroniczne metody pomiaru grubości cienkich transparentnych warstw wytwarzanych w procesach próżniowych.
PublikacjaW artykule opisano problemy związane z określaniem grubości cienkich transparentnych warstw dielektrycznych, syntetyzowanych w procesach próżniowych. Przedstawiono stosowane metody pomiarowe, szczególny nacisk kładąc na techniki optoelektroniczne, oparte na badaniu interferencji i zmiany stanu polaryzacji światła w wyniku oddziaływania z cienką warstwą oraz na analizie spektralnej. Opisano praktyczne układy, umożliwiające pomiary...
-
High-Gain Compact Circularly Polarized X-Band Superstrate Antenna for CubeSat Applications
PublikacjaIn this letter, a concept of high-gain circularly polarized X-band antenna employing a partially reflecting surface (PRS) has been presented. In the initial antenna analysis, the influence of parasitic elements size in the PRS structure on antenna radiation pattern parameters has been investigated and the optimal arrangement of the elements has been identified. The proposed antenna provides wide bandwidth of return loss above 10...
-
Manoeuvring forces on azimuthing podded propulsor model
PublikacjaThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...
-
Towards rainfall interception capacity estimation using ALS LiDAR data
PublikacjaIn this study we develop a spatial model for interception capacity of vegetation based on LiDAR data. The study is conducted in the natural wetland river valley dominated meadows, reeds and small bushes. The multiple regression model was chosen to relate the field measurements of interception capacity and LiDAR statistics at 2m grid. The optimal model was chosen by stepwise selection and further manual variables selection resulting...
-
Podpory nurtowe – wybrane zagadnienia teoretyczne
PublikacjaObliczenia hydrauliczne mostów i transportu rumowiska w rejonie podpór mostowych są przedmiotem wytycznych do projektowania. Metody tam proponowane są oparte na wzorach klasycznej hydrauliki. Przedstawiono inne podejście do obliczeń hydraulicznych, wykorzystujące dwuwymiarowy model przepływu wody. Pokazano numeryczną symulację hydrodynamiki w rejonie podpory mostu na Wiśle koło Kwidzyna. Na jej podstawie oszacowano intensywność...
-
Late Aortic Remodeling after Endovascular Repair of Complicated Type B Aortic Dissection—TEVAR Protects Only the Covered Segment of Thoracic Aorta
PublikacjaIntroduction: TEVAR is the preferred way of treatment of complicated type B aortic dissection. The purpose of the study was to assess the impact of TEVAR on aortic remodelling in the thoracic and abdominal segment in long-term follow-up. Methods: 23 patients with complicated type B aortic dissection were treated by TEVAR in years 2004-2012 in our Department. Aortic remodelling was rated based on preoperative and final follow-up...
-
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublikacjaPresented in article MF seals are being researched for sea technology purposes due to their excellenttightness and low resistance of motion. These features are most valuable for ring propellers and ship'smain propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systemsare designed with contactless...
-
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublikacjaPresented in article MF seals are being researched for sea technology purposes due to their excellent tightness and low resistance of motion. These features are most valuable for ring propellers and ship's main propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systems are designed with contactless...
-
Bridge Non-Destructive Measurements Using a Laser Scanning during Acceptance Testing: Case Study
PublikacjaOwing to the recent proliferation of inventory works on roads and railways, bridge acceptance tests have increased exponentially. These tests’ results are often misinterpreted owing to the use of various measuring equipment types, rendering integrated interpretation problematic. It is also problematic that adjusting the measurement method is difficult when the structure’s response to load is uncertain. Therefore, it is important...
-
Evaluation of Sicilian landraces of broccoli (B. oleracea var. italica Plenck) for quality traits
PublikacjaBrassica oleracea L. var. italica Plenck is one of the most popular vegetables which belong to Brassicaceae family. It is getting attention as an important source of bioactive compounds such as glucosinolates, and many other phytochemicals. In the frame of the H2020 BRESOV project, we evaluated three landraces (‘Broccolo nero', ‘Ramoso calabrese' and ‘Sparaceddu') and two commercial F1 hybrid cultivars (‘Marathon' and ‘Naxos')....
-
Extending the Frequency Limit of Microstrip-Coupled CSRR Using Asymmetry
PublikacjaAbstract— This article explains the frequency limitation in designing microstrip circuits based on a complementary split-ring resonator (CSRR) and reports a novel technique for increasing its operating frequency, which makes the CSRR suitable for high-frequency applications. This study helps in synthesizing the dimensions of symmetric CSRR (SCSRR) and asymmetric CSRR (ACSRR) circuits, which shows the applicability of the proposed...
-
Underwater wet welding of S1300 ultra-high strength steel
PublikacjaMarine Structures Volume 81, January 2022, 103120 Underwater wet welding of S1300 ultra-high strength steel Author links open overlay panelJacekTomkówGrzegorzRogalski https://doi.org/10.1016/j.marstruc.2021.103120 Get rights and content Under a Creative Commons licenseopen access Highlights • Technological method of S1300 steel underwater weldability improving was proposed. • Number of cracks and hardness of welded joints was...
-
Consideration of dynamic loads in the determination of axle load spectra for pavement design
PublikacjaAxle load spectra constitute a crucial part of the data for pavement design and pavement distress analysis. Typically, axle load spectra represent static load from vehicles and do not include dynamic loads generated by vehicles in motion. While dynamic loads can significantly contribute to faster pavement distress, this fact is mostly omitted in pavement design methods. The paper presents a methodology for consideration of dynamic...
-
Electrochemical performance of indium-tin-oxide-coated lossy-mode resonance optical fiber sensor
PublikacjaAnalysis of liquids performed in multiple domain, e.g., optical and electrochemical (EC), has recently focus significant attention. Our previous works have shown that a simple device based on indium-tin-oxide (ITO) coated optical fiber core may be used for optical monitoring of EC processes. At satisfying optical properties and thickness of ITO a lossy-mode resonance (LMR) effect can be obtained and used for monitoring of optical...
-
Interakcja momentu zginającego i siły osiowej w analizie nośności wybranych, cienkościennych przekrojów
PublikacjaObecnie w budownictwie coraz częściej wykorzystuje się lekkie konstrukcje stalowe, które posiadają korzystny stosunek ceny do nośności. Elementy takie uzyskuje się poprzez gięcie na zimno stosunkowo cienkich arkuszy blach i formowanie przekrojów w taki sposób, aby uzyskać oczekiwane wartości nośności. Za pomocą giętarki rolkowej bądź krawędziowej profiluje się ostateczny kształt przekroju, który dzięki dodatkowym usztywnieniom...