Filtry
wszystkich: 4709
wybranych: 2681
-
Katalog
- Publikacje 2681 wyników po odfiltrowaniu
- Czasopisma 4 wyników po odfiltrowaniu
- Osoby 16 wyników po odfiltrowaniu
- Projekty 5 wyników po odfiltrowaniu
- Laboratoria 1 wyników po odfiltrowaniu
- Kursy Online 114 wyników po odfiltrowaniu
- Wydarzenia 2 wyników po odfiltrowaniu
- Dane Badawcze 1886 wyników po odfiltrowaniu
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TYRE PYROLYSIS
-
Waste tire rubber as low-cost and environmentally-friendly modifier in thermoset polymers – a review
PublikacjaNowadays, waste tire rubber (WTR) management is a growing and serious problem. Therefore, research works focused on the development of cost-effective and environmentally-friendly methods of WTR recycling are fully justified. Incorporation of WTR into polymer matrices and composite materials attracts much attention, because this approach allows sustainable development of industrially applicable waste tires recycling technologies....
-
Fatigue Performance of Double-Layered Asphalt Concrete Beams Reinforced with New Type of Geocomposites
PublikacjaThe reinforcement of asphalt layers with geosynthetics has been used for several decades, but proper evaluation of the influence of these materials on pavement fatigue life is still a challenging task. The presented study investigates a novel approach to the reinforcement of asphalt layers using a new type of geogrid composite, in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions is bonded...
-
Comparative Study of the Reinforcement Type Effect on the Thermomechanical Properties and Burning of Epoxy-Based Composites
PublikacjaAramid (AF), glass (GF), carbon (CF), basalt (BF), and flax (FF) fibers in the form of fabrics were used to produce the composites by hand-lay up method. The use of fabrics of similar grammage for composites’ manufacturing allowed for a comprehensive comparison of the properties of the final products. The most important task was to prepare a complex setup of mechanical and thermomechanical properties, supplemented by fire behavior...
-
Distortional buckling of composite thin-walled columns of a box-type cross section with diaphragms
PublikacjaDistortional buckling of axially compressed columns of box-like composite cross sections with andwithout internal diaphragms is investigated in the framework of one-dimensional theory. The channel membersare composed of unidirectional fibre-reinforced laminate. Two approaches to the member orthotropic materialare applied: homogenization based on the theory of mixture and periodicity cells, and homogenization basedon the Voigt–Reuss...
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublikacjaGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
EVALUATION OF THE USE OF M2M-TYPE NB-IoT AND LTE TECHNOLOGIES FOR MARITIME COMMUNICATION SYSTEMS
PublikacjaThe development of IoT (the Internet of Things) wireless transmission opens a new era in communication systems. In the next years, the development and implementation of IoT systems will be very dynamic. It can be seen that the solutions of LTE – NB-IoT (Long Term Evolution – Narrowband IoT) transmission devices are implemented in a wide range of terrestrial solutions, e.g. smart grids. This paper aims to analyse the possibility...
-
Sources of contamination in sediments of retention tanks and the influence of precipitation type on the size of pollution load
PublikacjaDensification of cities and urban population contributes to increased runoff and suspended solids and alteration of the urban water cycle. Nowadays, Blue-Green Infrastructure is promoted to increase a city’s resilience to floods; however, stormwater drainage systems, supported with retention tanks are still important in protecting urban areas against floods. Sediment accumulation in stormwater infrastructure relates to an issue...
-
Porównanie przebiegu enzymatycznej hydrolizy oleju rzepakowego i strukturyzowanych lipidów zawierających kwas behenowy. The comparision on the course of enzymatic hydrolysis of rapeseed oil and structured lipids containing behenoic acid.
PublikacjaPorównywano przebieg enzymatycznej hydrolizy oleju rzepakowego i strukturyzowanych lipidów zawierających kwas behenowy (C22:0). Hydroliza prowadzona była w obecności lipazy trzustkowej, w warunkach stymulujących proces trawienia. Stwierdzono, że olej rzepakowy hydrolizowany jest znacznie szybciej niż strukturyzowane lipidy z kwasem behenowym.
-
Tailoring of SiOC composition as a way to better performing anodes for Li-ion batteries
PublikacjaPolymer derived silicon oxycarbide (SiOC) ceramics are investigated as potential anodes for lithiumion batteries. Different SiOC ceramics are prepared by pyrolysis (1000 °C and 1400 °C under controlled argon atmosphere) of polysiloxanes ceramic precursors. Preceramic polymers are synthesized using the sol–gel method. Phenyltriethoxysilane (PhTES) and methyltriethoxysilane (MTES) have been used as starting precursors and mixed with...
-
The influence of type of dispersed phase on rolling contact fatigue of lubricating greases on mineral base oil
Publikacja -
Optimization of Transport Properties of A-Site Ordered LnBa1-xSrxCo2-yFeyO5+ Perovskite-Type Cathode Materials
Publikacja -
Rock salt ordered-type double perovskite anode materials for solid oxide fuel cells
Publikacja -
The conception of uncertainty analysis of reliability assessment of the MC type diesel engine lubricating oil system
PublikacjaOmówiono elementy składające się na niepewność oszacowania niezawodności instalacji oleju smarowego dla silników typu MC. Przedstawiono, posługując się przykładem obliczeniowym, koncepcję analizy niepewności oceny rozpatrywanej instalacji. Ponadto zaproponowano sposób interpretacji otrzymanego wyniku, obarczonego dużą niepewnością, przy użyciu liczb rozmytych.
-
Thermo-mechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
PublikacjaThermomechanical reclaiming of ground tire rubber (GTR) was performed at different temperatures (60, 120, and 180°C) using a co-rotating twin-screw extruder. Obtained samples were used in styrene-butadiene rubber (SBR) blends. As reference samples, SBR compounds containing untreated GTR were used. Curing characteristics, static and dynamic mechanical properties, and morphology of the obtained blends were determined. The results...
-
Prospective assessment of continuous subcutaneous insulin infusion therapy in young children with type 1 diabetes
Publikacja -
Does social–economical transformation influence the incidence of type 1 diabetes mellitus? A Polish example
Publikacja -
UGT1A1gene polymorphism as a potential factor inducing iron overload in the pathogenesis of type 1 hereditary hemochromatosis
Publikacja -
Microstructure and corrosion properties of the (Mn-N-O-P) type layers created on aluminium alloys
PublikacjaPrzedstawiono mikrostrukturę i właściwości korozyjne warstw powierzchniowych typu (Mn-N-O-P) wytworzonych na stopach aluminium. Wykazano, iż warstwy (Mn-N-O-P) podwyższają wielokrotnie odporność korozyjną stopów aluminium i mogą być stosowane jako warstwy ochronne na tych materiałach.
-
A new potential mode of cardiorenal protection of KLOTHO gene variability in type 1 diabetic adolescents
Publikacja -
Inhalation risk to PAHs and BTEX during barbecuing: The role of fuel/food type and route of exposure
Publikacja -
Studies on selectivity of hydrocarbon group type separation of petroleum vacuum distillates and base oils by HPLC.
PublikacjaW pracy przedstawiono wyniki badań nad doborem selektywnego chromatograficznego układu HPLC, umożliwiającego rozdzielenie grupowe produktów naftowych otrzymanych z destylacji próżniowej ropy naftowej, w tym, mineralnych olejów bazowych. Stwierdzono, że konieczny układ chromatograficzny wymaga wykorzystania dwóch kolumn wypełnionych żelem krzemionkowym ze związanymi grupami nitrofenopropylowymi, połączonych szeregowo z dwiema...
-
Multiple solutions of indefinite elliptic systems via a Galerkin-type Con- ley index theory
PublikacjaW pracy wykazano prawdziwość hipotezy Angenenta i van der Vorsta dotyczącąilości rozwiązań pewnego układu eliptycznego. Liczbę rozwiazań szacuje się zdołu przy pomocy niezmiennika topologicznego zwanego uogólnionym indeksemMorse`a. W dowodzie stosuje sie niezmienniczy index Conleya w przestrzeniachHilberta.
-
Chimeric Dr fimbriae with a Herpes Simplex virus type 1 epitope as a model for a recombinant vaccine.
PublikacjaBiałko adhezyny DraE uropatogennych szczepów E. coli Dr+ zostało wykorzystane jako nośnik 11a a determinanty antygenowej glikoproteiny D wirusa HSV ty-pu 1. Sekwencja kodująca epitop HSV została wklonowana do genu draE w obrębie regionu N- terminalnego eksponowanej powierzchniowo domeny 2. Ekspresjachimerycznych białek DraE-HSV została potwierdzona za pomocą mikroskopii immunofluorescencyjnej i elektronowej.
-
Research of new two-speed planet type gear hydraulic motors with axial clearance compensation.
PublikacjaOpisano sposoby realizacji napędu dwubiegowego na przykładzie silnika satelitowego HS 3,2 [dm3/obr.] oraz przedstawiono zalety i przykłady zastosowań napędów wielobiegowych. Zaprezentowano porównanie metody analitycznej oraz eksperymentalnej wyznaczania nierównomierności chłonności hydraulicznego silnika satelitowego w celu zweryfikowania własności eksploatacyjnych silnika dwubiegowego HS 3,2/0,8 [dm3/obr] wyprodukowanego przez...
-
New Type of Small Broad-Band Internal Antenna for Third Generation Mobile Phone Handsets.
PublikacjaW pracy przedstawiono nową szerokopasmową antenę łatową przeznaczoną dla telefonów komórkowych trzeciej generacji. Proponowana struktura zawiera obwód (rezonator) w kształcie litery U i zaliczana jest do klasy PIFA (planar inverted-F antenna). W trakcie procesu projektowania przeprowadzono szereg symulacji elektromagnetycznych (metoda momentów), których wyniki zweryfikowano w oparciu o pomiary charakterystyk wykonanego prototypu....
-
The formal safety assesment in conforming to chosen vessel's type on the ground of hydromechanic characteristics in critical conditions.
PublikacjaTragedia jednego ze statków typu ro-ro pokazała podatność tego typu statków na utratę stateczności, przewrócenie a w ostateczności zatonięcie. Wszystkie ro-rowce charakteryzują się małym zanurzeniem, a wynurzona część kadłuba podatna jest na działanie wiatru. Jeżeli dodatkowo w takich warunkach dochodzi element nieprawidłowego rozmieszczenia pojazdów i ich słabego zamocowania to groźba przesunięcia ładunku staje się realna. W konsekwencji...
-
High-performance liquid chromatography in group-type separation and technical or process analytics of petroleum products
PublikacjaW pracy dokonano przeglądu i poddano krytycznej ocenie metody oznaczania składu grupowego produktów naftowych o różnej lotności, zarówno metody znormalizowane, jak i opisane w literaturze naukowej. W zdecydowanej większości są to metody wykorzystujące technikę chromatografii cieczowej w układzie faz normalnych (NP-HPLC). Na podstawie danych z literatury oraz własnych studiów i badań należy stwierdzić, że im wyższy zakres temperatury...
-
Lanthanide co-doped TiO2: the effect of metal type and amount on surface properties and photocatalytic activity
PublikacjaPreparation of new rare earth metal-containing TiO2 nanocomposites (Nd3+/Er3+, Nd3+/Eu3+, Eu3+/Ho3+-TiO2) using sol–gel route and their photoactivity under visible and ultraviolet light is reported. The obtained photocatalysts were subsequently characterized by Brunauer–Emmett–Teller (BET) method, UV–Vis diffuse-reflectance spectroscopy (DRS), luminescence spectroscopy, X-ray photoelectron spectroscopy (XPS) and X-ray powder diffraction...
-
Curing characteristics, mechanical properties and morphology of butyl rubber filled with ground tire rubber (GTR)
PublikacjaThe results on testing application of ground tire rubber (GTR), as potential filler for butyl rubber, are pre- sented. The GTR content variation, within the range of 10–90 phr, was studied with respect to the vulcanization process, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and the morphology of the obtained vulcanizates. Butyl rubber was characterized...
-
Bone status in adolescents and young adults with type 1 diabetes: a 10-year longitudinal study
Publikacja -
New type of repeated Si–C-podand catalysts for solid–liquid phase transfer reactions
Publikacja -
Addition of novel benzylmagnesium “ate” complexes of BnR2MgLi type to 2-(thio)pyridones and related compounds
Publikacja -
Average Structure, Local Structure, Photoluminescence, and NLO Properties of Scheelite Type NaCe(WO4)2
Publikacja -
Polyurethane/ground tire rubber composite foams based on polyglycerol: processing, mechanical and thermal properties
PublikacjaDuring the synthesis of rigid polyurethane foams, petrochemical polyol was substituted with polyglycerol, the product of thermo-catalytic polycondensation of waste glycerol, resulting from biodiesel production. Two types of ground tire rubbers, untreated and thermo-mechanically reclaimed, were used to obtain ‘‘green’’ polyurethane-polyglycerol composite foams. Samples were prepared by a single-step method for the ratio of NCO/OH...
-
Mountain pass type periodic solutions for Euler–Lagrange equations in anisotropic Orlicz–Sobolev space
PublikacjaUsing the Mountain Pass Theorem, we establish the existence of periodic solution for Euler–Lagrange equation. Lagrangian consists of kinetic part (an anisotropic G-function), potential part and a forcing term. We consider two situations: G satisfying at infinity and globally. We give conditions on the growth of the potential near zero for both situations.
-
Application of gas chromatography–tandem mass spectrometry for the determination of amphetamine-type stimulants in blood and urine
PublikacjaAmphetamine, methamphetamine, phentermine, 3,4-methylenedioxyamphetamine (MDA), 3,4-methylenedioxymethamphetamine (MDMA), and 3,4-methylenedioxy-N-ethylamphetamine (MDEA) are the most popular amphetamine-type stimulants. The use of these substances is a serious societal problem worldwide. In this study, a method based on gas chromatography-tandem mass spectrometry (GC-MS/MS) with simple and rapid liquid-liquid extraction (LLE)...
-
Numerical analysis of test embankment on soft ground using multi-laminate type model with destructuration
PublikacjaW artykule przedstawiono model wielopłaszczyznowy (multi-laminate) uwzględniający anizotropię struktury słabonośnych gruntów drobnoziarnistych. Anizotropia indukowana naprężeniem, która otrzymuje się przy zastosowaniu modeli wielopłaszczyznowych, jest dodatkowo wzmocniona poprzez wprowadzenie prekonsolidacji zależnej od orientacji przestrzennej. Model przedstawiono w wersji sprężysto-plastycznej, w której możliwa jest symulacja...
-
Inhibition of T-type calcium channel disrupts Akt signaling and promotes apoptosis in glioblastoma cells.
PublikacjaGlioblastoma multiforme (GBM) are brain tumors that are exceptionally resitant to both radio- and chemotherapy regimens and novel approaches to treatment are needed. T-type calcium channels are one type of low voltage-gated channel (LVCC) involved in embryonic cell proliferation and differentiation; however they are often over-expressed in tumors, including GBM. In this study, we found that inhibition of T-type Ca channels in GBM...
-
The inhibition effect of mad Honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution
PublikacjaThe inhibition effect of mad honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution was investigated by Tafel extrapolarisation (TP), electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). All the studied parameters exhibited good anti-corrosive properties against corrosion of 2007-type aluminium alloy in the test solution; the corrosion rates decreased with the increase...
-
Perovskite-type KTaO3–reduced graphene oxide hybrid with improved visible light photocatalytic activity
PublikacjaNovel rGO–KTaO3 composites with various graphene content were successfully synthesized using a facile solvothermal method which allowed both the reduction of graphene oxide and loading of KTaO3 nanocubes on the graphene sheets. The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) with energy dispersive X-ray analysis (EDX), Fourier...
-
Electrohydrodynamic flow and particle collection efficiency in a one-sided spike-plate type electrostatic precipitator
Publikacja -
Mechanical properties of polyester reinforced PVC coated fabric subjected to biaxial loading of creep type
PublikacjaThe goal of the current study is to analyze the basic mechanical properties of the architec-tural fabric VALMEX, which is a composite material built of reinforcing polyester thread families and both sides PVC coated. The material was firstly subjected to biaxial loading of creep type for about 48 hours. The stress levels of the creep loading in two main or-thogonal directions of the fabric (commonly called the warp and fill directions)...
-
Load test of new European record holder in span length among extradosed type bridges
PublikacjaThe article presents acceptance load tests of a newly built extradosed MS-3 bridge located along the national road DK-16 near Ostróda (Poland). The structure features significant dimension in European reference scale. It is a new record holder in span length regarding this distinct bridge category. Its length ranges 206 m. Static and dynamic load tests were performed here. The program was extended by entire structural laser scanning...
-
2-D constitutive equations for orthotropic Cosserat type laminated shells in finite element analysis
PublikacjaWe propose 2-D Cosserat type orthotropic constitutive equations for laminated shells for the purpose of initial failure estimation in a laminate layer. We use nonlinear 6-parameter shell theory with asymmetric membrane strain measures and Cosserat kinematics as the framework. This theory is specially dedicated to the analysis of irregular shells, inter alia, with orthogonal intersections, since it takes into account the drilling...
-
Synergistic Effects of Bitumen Plasticization and Microwave Treatment on Short-Term Devulcanization of Ground Tire Rubber
PublikacjaGround tire rubber (GTR) was mechano-chemically modified with road bitumen 160/220 and subsequently treated using a microwave radiation. The combined impact of bitumen 160/220 content and microwave treatment on short-term devulcanization of GTR was studied by thermal camera, wavelength dispersive X-ray fluorescence spectrometry (WD-XRF), static headspace, and gas chromatography-mass spectrometry (SHS-GC-MS), thermogravimetric analysis...
-
Ground tire rubber thermo-mechanically devulcanized in the presence of waste engine oil as asphalt modifier
PublikacjaCross-linked elastomers network is main limitation for industrial usage of ground tire rubber (GTR) as asphalts’ and road pavements modifier. GTR was thermo-mechanically devulcanized via extrusion in the presence of waste engine oil (WEO) at temperature ranges from 150 to 280 °C. Combined impact of WEO content and extruder barrel temperature on the change of cross-linked structure of degraded GTR (DTGR) was investigated through...
-
A selection of PID type controller settings via LQR approach for two-wheeled balancing robot
PublikacjaThe problem of PID type controller tuning has been addressed in this paper. In particular, a method of selection of PD settings based on the solution of linear–quadratic optimisation problem using the energy criterion has been investigated. Thus, the possibility of transforming optimal settings of the linear–quadratic regulator into the settings of the controller in the classical control system has been given. The presented methodology...
-
Insights into Stoichiometry Adjustments Governing the Performance of Flexible Foamed Polyurethane/Ground Tire Rubber Composites
PublikacjaPolyurethanes (PU) are widely applied in the industry due to their tunable performance adjusted by changes in the isocyanate index—stoichiometric balance between isocyanate and hydroxyl groups. This balance is affected by the incorporation of modifiers of fillers into the PU matrix and is especially crucial for PU foams due to the additional role of isocyanates—foaming of the material. Despite the awareness of the issue underlined...
-
Impact response of novel layered two stage fibrous composite slabs with different support type
PublikacjaThe performance of novel Layered Two Stage Fibrous Composite slabs (LTSFC) was pioneered under falling mass collisions using a combined experimental and numerical study. Such LTSFC slabs consist of three layers with and without the insertion of glass fibre mesh between the layers. LTSFC techniques were used to fabricate the composite slabs with three layers including 3%, 1.5%, and 3% of fibre content for the top, middle, and...
-
Synthesis of CoFe2O4 Nanoparticles: The Effect of Ionic Strength, Concentration, and Precursor Type on Morphology and Magnetic Properties
PublikacjaThe present study highlights the effect of metal precursor types (SO4 2¯, Cl¯, and NO3¯), their concentration, and the influence of ionic strength of reaction environment on the morphology, surface, and magnetic properties of CoFe2O4 particles. The magnetic nanoparticles were obtained by chemical coprecipitation in alkaline medium at increasing metal concentration in the range of 0.0425 mol·dm-3 to 0.17 mol·dm-3 and calcination...