Filters
total: 188
filtered: 168
-
Catalog
Chosen catalog filters
Search results for: IMO STANDARD MANOEUVRING TESTS
-
Application of the IMO standard manoeuvres procedure for pod-driven ships
PublicationInternational Maritime Organisation (IMO) in the resolution MSC.137(76) Standards for Ship manoeuvrability presents the manoeuvring criteria that has to be satisfied by majority of seagoing ships. Together with the criteria, procedures for carrying out the manoeuvring tests are also presented. They however do not correspond directly to ships with non-conventional steering-propulsion devices, like pod drives. IMO is aware of this...
-
Equivalent standard manoeuvres for pod-driven ships
PublicationProcedures for carrying out the manoeuvring tests presented in International Maritime Organisation (IMO) resolution MSC.137(76) are based on the capabilities of ships with conventional steering-propulsion systems. Therefore they do not correspond to ships with other steering-propulsion devices, like pod drives. IMO is aware of this shortcoming and for ships with non-conventional steering and propulsion system may permit the use...
-
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublicationAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Prediction of manoeuvring abilities of 10000 DWT pod-driven coastal tanker
PublicationThis paper aims to present a new approach in the prediction of manoeuvring abilities of pod-driven ships. A new mathematical model of motions based on MMG methodology was developed and a new type of description of forces acting on azimuth drives is presented. Captive model tests of medium-size coastal tanker and pod open water tests were carried out in CTO S.A. (Ship Design and Research Centre S.A.) to obtain hull hydrodynamic derivatives...
-
Scale effect in the self-propulsion prediction for Ultra Large Container Ship with contra-rotating propellers
PublicationThis article addresses the problem of the scale effect for an Ultra Large Container Ship (ULCS) with a novel twin-crp-pod propulsion system. Twin-crp-pod steering-propulsion arrangement is an innovative solution that gains from three well-known systems: twin-propeller, contra-rotating propellers and pod propulsors. It is expected that applying the twin-crp-pod system to the analysed Ultra Large Container Ship will increase propulsion...
-
Longitudinal Motion Due to Action of Tunnel Thrusters
PublicationTunnel thrusters are propulsion and active control devises that provide a side force, or transverse thrust, to support mooring operations or position keeping. They shorten the time of manoeuvring, reduce the cost of towage and since inception, manoeuvrability specifically in ports has become a lot easier. Tunnel thrusters can either be operated manually or with the help of Dynamic Positioning systems which makes it even more efficient. Theoretically,...
-
Manoeuvring forces on azimuthing podded propulsor model
PublicationThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...
-
Study of Noise Propagation for Small Vessels
PublicationThe paper presents the results of the noise propagation analysis in ship structures tested in a number of AHTS (Anchor Handling Tug Supply) vessels. Statistical Energy Analysis (SEA) based on numerical model developed specially for the purpose of this numerical investigation were conducted. This numerical model enabled the analysis of both the structural elements and the acoustic spaces. For the detailed studies 47 points fixed...
-
Mechanical properties of Precontraint 1202 S2 based on uniaxial tensile and creep tests
PublicationThe purpose of the paper is the estimation of the polyvinyl chloride – polyester-coated fabric (Precontraint 1202 S2) mechanical properties under uniaxial tensile tests as well as short- and long-time creep tests. The uniaxial tests are the basis of non-linear elastic description while the creep tests are used for the evaluation of the stiffness parameters in time and for the identification of the standard viscoelastic model. The...
-
Numerical Estimation of Hull Hydrodynamic Derivatives in Ship Maneuvering Prediction
PublicationPrediction of the maneuvering characteristics of the ship at the design stage can be done by means of model tests, computational simulations or a combination of both. The model tests can be realized as direct simulation of the standard maneuvers with the free running model, which gives the most accurate results, but is also the least affordable as it requires very large tank or natural lake, as well as complex equipment of the...
-
Numerical analysis of the container vessel's self-propulsion at different rudder deflection angles
PublicationNowadays, CFD becomes one of the most commonly used research method in ship hydrodynamics, limited to the analyses of hull resistance in calm water. With continuously improving computing power and increasingly more accurate numerical methods it is possible to simulate more complex cases. State of the art CFD tools also enable development of new ways of assessing ship maneuvering performance. This paper presents an attempt on...
-
Numerical analysis of the container vessel's self-propulsion at different rudder deflection angles
PublicationNowadays, CFD becomes one of the most commonly used research method in ship hydrodynamics, limited to the analyses of hull resistance in calm water. With continuously improving computing power and increasingly more accurate numerical methods it is possible to simulate more complex cases. State of the art CFD tools also enable development of new ways of assessing ship maneuvering performance. This paper presents an attempt on using...
-
Study on the Positioning Accuracy of GNSS/INS Systems Supported by DGPS and RTK Receivers for Hydrographic Surveys
PublicationHydrographic surveys, in accordance with the International Hydrographic Organization (IHO) S-44 standard, can be carried out in the following five orders: Exclusive, Special, 1a, 1b and 2, for which minimum accuracy requirements for the applied positioning system have been set out. They are as follows, respectively: 1, 2, 5, 5 and 20 m, with a confidence level of 95% in twodimensional space. The Global Navigation Satellite System...
-
Underwater Local Cavity Welding of S460N Steel
PublicationIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublicationThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
ENERGY EFFICIENT SMALL INLAND PASSENGER SHUTTLE FERRY WITH HYBRID PROPULSION - CONCEPT DESIGN, CALCULATIONS AND MODEL TESTS
PublicationIn recent years, there has been a significant development in “green” and energy efficient propulsion systems, which fits into the general trend of environmentally friendly “green shipping”. The pursued goal is to construct a safe passenger ship that is low in energy demand and equipped with a highly energy efficient, emission-free propulsion system. The paper presents main problems encountered by designers of a small, hybrid-powered...
-
TIME-DOMAIN NUMERICAL EVALUATION OF SHIP RESISTANCE AND MOTION IN REGULAR WAVES BY USING THE CFD URANS METHOD
PublicationTaking into account the International Maritime Organisation’s (IMO) strategy to radically reduce the GHG emitted by the shipping industry towards zero emission operation, today's assessment of ship behaviour in waves, its seakeeping characteristics and resistance and their interrelation with fuel consumption and emissions are one of the most attended research subject. There are three methods to conduct this analysis, which are...
-
Object serialization and remote exception pattern for distributed C++/MPI application
PublicationMPI is commonly used standard in development of scientific applications. It focuses on interlanguage operability and is not very well object oriented. The paper proposes a general pattern enabling design of distributed and object oriented applications. It also presents its sample implementations and performance tests.
-
An Efficient Simulation Method of Massive MIMO Antenna Arrays used in 5G Mobile Phones
PublicationThis paper deals with a model-order reduction method, applied to speed-up the simulations of MIMO antenna arrays, performed by means of finite element method. The obtained results of the numerical tests show that the described technique is reliable and considerably increases the efficiency of the standard finite element method.
-
Determination of p-y curves for offshore piles based on in-situ soil investigations
PublicationOffshore piles are subjected to complex loads with considerable lateral component. The pile-soil response to lateral loads can be described with the p-y method. For a given depth the load–deflection relationship is built to simulate the surrounding soil stiffness. This state-of-art paper presents a brief discussion of determination methods for the p-y curves using a standard approach based on the soil parameters derived from laboratory...
-
Testing for conformance of parallel programming pattern languages
PublicationThis paper reports on the project being run by TUG and IMAG, aimed at reducing the volume of tests required to exercise parallel programming language compilers and libraries. The idea is to use the ISO STEP standard scheme for conformance testing of software products. A detailed example illustrating the ongoing work is presented.
-
Evaluation of Sound Enhancement in Mobile Device Using Virtual Bass Synthesiss Algorithm
PublicationAn experiment conducted to validate possibility of use virtual bass synthesis (VBS) algorithm in a portable computer is presented. The subjective listening tests based on the procedure of pairwise comparison between VBS, based on the so-called missing fundamental phenomenon, and standard bass boost technique are employed. The evaluation was carried out in two types of conditions: in a professional listening room and employing an...
-
Problems of Active Dynamic Thermography Measurement Standardization in Medicine
PublicationReliability of thermographic diagnostics in medicine is an important practical problem. In the field of static thermography, a great deal of effort has been made to define the conditions for thermographic measurements, which is now the golden standard for such research. In recent years, there are more and more reports on dynamic tests with external stimulation, such as Active Dynamic Thermography, Thermographic Signal Reconstruction...
-
Experimental research on technical fabric of the Forest Opera Roof in Sopot
PublicationThe experimental analysis of the technical fabric Valmex is presented. The study involves uniaxial tensile, cyclic, rheological and biaxial tests. Some of the main differencies between two types of the analysed material have been identified. Mechanical properties of the textile have been modeled by the viscoelastic standard model with quite good effect.
-
BADANIA KOMPOZYTOWEGO MOSTU DLA PIESZYCH
PublicationThe paper presents in situ load testing of the innovative footbridge of FOBRIDGE grant mounted at Gdansk University of Technology. The span of composite sandwich structure (GFRP skins, PET core) and the scope of static and dynamic tests are presented. The selected, representative results of in situ measurements and data obtained from the SHM monitoring system are discussed. Besides the standard testing procedures on the full scale...
-
FAILURE OF MAGNETIC FLUID SEALS OPERATING IN WATER: PRELIMINARY CONCLUSIONS
PublicationThe article analyses properties of magnetic fluid seals installed in rotary sealing no des which operate in the utility water environment. Seals of this type have been examined as a possible solution to the problem with ship manoeuvring propulsion sealing. The present analysis bases on laboratory durability tests of magnetic fluid seals expo sed to long - term utility water loads, at different water pressures and shaft revolutions....
-
The effect of tire aging on acoustic performance of CPX reference tires
PublicationReduction of tire/road noise is one of the biggest environmental challenges of road traffic. To reduce that noise it is necessary to perform acoustic measurements on the base of wellproven standard procedures. One method of measurements that is in common use, namely the Close Proximity Method (CPX), is described in standard ISO-DIS 11819-2. As this method is used to classify road surfaces regarding their influence on vehicle noise,...
-
Comparison of the tests for equivalence of the measurement methods for measurement of PM10 dust in ambient air
PublicationThe paper presents the motives for conducting the equivalence tests and the reasons of discrepancies between the results of PM10 dust concentration obtained via the reference method and the methods based on 'on-site' measurement. The reference and non-reference methods of measurement of PM10 dust concentration in air have been discussed. Field tests for equivalence, following the Polish standard and the European Union (EU) guidelines,...
-
Novel 5.1 Downmix Algorithm with Improved Dialogue Intelligibility
PublicationA new algorithm for 5.1 to stereo downmix is introduced, which addresses the problem of dialogue intelligibility. The algorithm utilizes proposed signal processing algorithms to enhance the intelligibility of movie dialogues, especially in difficult listening conditions or in compromised speaker setup. To account for the latter, a playback configuration utilizing a portable device, i.e. an ultrabook, is examined. The experiments...
-
Influence of nonlinearities on the efficiency and accuracy of FEM calculations on the example of a steel build-up thin-walled column
PublicationDue to the increase of computing capabilities of standard processing units, it is possible to perform complex analyses, considering a number of nonlinearities, such as geometric, material and boundary (contact) even on personal computers. In the paper, the authors have analysed the efficiency and accuracy of standard PC’s FEM calculations performed in Abaqus CAE 2017 software on the example of a critical load assessment of a thin-walled...
-
Analysis of EN 1993-1-6 guidelines about determining amplitudes of equivalent imperfections of steel cylindrical shells subjected to uniform external pressure
PublicationCivil engineering structures should be designed with reference to relevant standards. One of them is a Eurocode 3 standard EN 1993-1-6:2007: Design of steel structures Part 1-6: Strength and Stability of Shell Structures. According to this standard, the value of buckling load can be determined using different approaches: classical hand calculations (stress design) and geometrical and material non-linear analysis of an imperfect...
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublicationThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
Effect of adhesive compliance in the assessment of soft adhesives with the wedge test
PublicationWedge tests are usually analysed assuming that the free, unbonded members may be treated as encastré cantilever beams. However, if the adhesive layer is sufficiently flexible (e.g., due to low elastic modulus), then significant strain in the bonded region may occur and lead to modification of the behaviour outside this region. Using in conjunction a sensitive strain gauge method on asymmetric wedge tests and a mathematical analysis...
-
Ocena klimatu akustycznego w przestrzeni pasażerskiej elektrycznego zespołu trakcyjnego serii EN57
PublicationW pracy przedstawiono wyniki badań poziomów dźwięku w przestrzeni pasażerskiej elektrycznego zespołu trakcyjnego (EZT) serii EN57 podczas postoju, rozruchu, jazdy oraz hamowania. Badania przeprowadzono na podstawie autorskiej metodyki badawczej bazując na normie PNEN ISO 3381:Kolejnictwo. Akustyka. Pomiar hałasu wewnątrz pojazdów szynowych. Badania przeprowadzono na linii kolejowej nr 250 od przystanku Gdańsk Śródmieście do stacji...
-
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublicationThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
Poly(hydroxybutyrate-co-hydroxyvalerate) as a biodegradable binder in a negative electrode material for lithium-ion batteries
PublicationIn this work, graphite-based negative electrode for lithium-ion battery consisting a novel and biodegradable binder poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) is compared with standard graphite electrode with polyvinylidene fluoride (PVDF) as a binder. The rate and cycling performance of lithium ion insertion/extraction of electrodes with PHBV in a half-cell configuration are evaluated. Moreover, on the basis of the electrochemical...
-
Effect of Storage Conditions of Rutile Flux Cored Welding Wires on Properties of Welds
PublicationThe influence of storage locations of two grades of rutile flux cored welding wires on their surface condition and the strength of the welds made with them were studied. Wires were stored in real urban conditions (Gdańsk and Katowice) for 1 month, simultaneously recording changes in conditions: temperature and relative humidity of the environment. Visual tests of wires in the delivered and stored condition as well as visual and...
-
Light-Powered Starter for Micro-Power Boost DC–DC Converter for CMOS Image Sensors
PublicationThe design of a starter for a low-voltage, micro-power boost DC–DC converter intended for powering CMOS image sensors is presented. A unique feature of the starter is extremely low current, below 1 nA, supplying its control circuit. Therefore, a high-voltage (1.3 V) configuration of series-connected photovoltaic diodes available in a standard CMOS process or a small external LED working in photovoltaic mode can be used as an auxiliary...
-
Acoustic evaluation of road surfaces using different Close Proximity testing devices
PublicationAccording to the valid standard, Close Proximity (CPX) method intends to evaluate the influence of road surfaces on traffic noise. Measurements may be carried out with the use of a self-powered vehicle or a special test trailer equipped with testing tyre towed by another vehicle. Two different testing devices took part in the research organized in Poland in order to determine the ranking of road surfaces in terms of acoustic parameters....
-
OCENA NOŚNOŚCI STAREGO MOSTU ŁUKOWEGO W JAGODNIKU
PublicationArtykuł opisuje przeprowadzoną analizę statyczno-wytrzymałościowa 95-letniego betonowego mostu łukowego zlokalizowanego w Jagodniku w północnej Polsce. Trwałość i wytrzymałość starego betonu są określane na podstawie wybranych właściwości mechanicznych, fizycznych i chemicznych. Program badań laboratoryjnych składał się z następującego zestawu badań: pomiary głębokości strefy skarbonatyzowanej i gęstości w stanie suchym, badania...
-
Intergranular Corrosion Detection Using Electromagnetic Transducers for Ultrasonic Testing
PublicationThe aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after...
-
Application of infrared thermoography to non-contact testing of varistors
PublicationTesting of varistors using thermography was carried out in order to assess their protective properties against possible overvoltage phenomena in the form of high-level voltage surges. An advantage of the thermography technique is non-contact temperature measurement. It was proposed to assess the properties of varistors workingin electronic devices as protective elements, on the basis of estimating temperature increments on varist...
-
TEMPERATURE INFLUENCE ON TIRE ROLLING RESISTANCE MEASUREMENTS QUALITY
PublicationGlobal warming makes it necessary to reduce energy consumption, which in the case of motor vehicles, is connected, among other things, with reduction of resistive forces acting on a vehicle during its motion. One of the most important components of those forces is rolling resistance, which is very difficult to measure, especially in road conditions. The article deals with issues related to the influence of the thermal state of...
-
Improvement of S355G10+N steel weldability in water environment by Temper Bead Welding
PublicationThe normalized S355G10 + N steel was chosen for testing, it is used in a variety of applications including the building of offshore structures, which may require repairs in water environment. The main aim of the work was to check susceptibility to cold cracking for fillet welds – Controlled Thermal Severity (CTS) tests and butt welds – Tekken tests and in the next step evaluation of effectiveness of Temper Bead Welding (TBW) application...
-
A concept for reducing PM 10 emissions for car brakes by 50%
PublicationWith regard to airborne particles with an aerodynamic diameter of less than 10 μm (PM10), in countries in the European Union, the mass of brake emissions equals approximately 8–27% of the total traffic-related emissions. Using a research methodology combining tests at different scale levels with contact mechanics simulations and PM10 chemical characterization, the REBRAKE EU-financed project had the following aims: i) to demonstrate...
-
A non-uniform real-time speech time-scale stretching method
PublicationAn algorithm for non-uniform real-time speech stretching is presented. It provides a combination of typical SOLA algorithm (Synchronous Overlap and Add ) with the vowels, consonants and silence detectors. Based on the information about the content and the estimated value of the rate of speech (ROS), the algorithm adapts the scaling factor value. The ability of real-time speech stretching and the resultant quality of voice were...
-
Development and performance analysis of a novel multiphase doubly-fed induction generator
PublicationThis paper presents the research into the design and performance analysis of a novel five-phase doubly-fed induction generator (DFIG). The designed DFIG is developed based on standard induction motor components and equipped with a five-phase rotor winding supplied from the five-phase inverter. This approach allows the machine to be both efficient and reliable due to the ability of the five-phase rotor winding to operate during...
-
An Improvement of Global Complex Roots and Poles Finding Algorithm for Propagation and Radiation Problems
PublicationAn improvement of the recently developed global roots finding algorithm has been proposed. The modification allows to shorten the computational time by reducing the number of function calls. Moreover, both versions of the algorithms (standard and modified) have been tested for numerically defined functions obtained from spectral domain approach and field matching method. The tests have been performed for three simple microwave...
-
PROPELLER INVESTIGATIONS BY MEANS OF NUMERICAL SIMULATION
PublicationThe analyses of hydroacoustics are of high interest at the moment due to strong impact of hydroacoustic phenomena on marine environment; the noises, generated e.g. by marine traffic, may be harmful for sea life. The analyses presented here are focused on one of main sources of noises generated by ships, i.e. cavitating propeller. The goal of the work is the assessment of the cavitation phenomenon, carried out with the standard...