Filters
total: 701
filtered: 666
Search results for: TECHNICAL SOLUTIONS
-
Integrated Application of GPR and Ultrasonic Testing in the Diagnostics of a Historical Floor
PublicationThe paper presents the results of integrated ground penetrating radar (GPR) and ultrasonic testing (UT) measurements conducted on a historical floor in St. Nicholas’ Church, Gdańsk, Poland. The described inspection was the first stage of the technical state assessment of the building. The aim of the study was the detection of underfloor air gaps, which were observed in a few trial pits. The condition of the ground under the floor...
-
Thickness accuracy of sash gang sawing
PublicationThin lamellae, corresponding to the layer components of structural glued members, i.e. 2-ply or 3-ply glued parquet, can be manufactured in re-sawing operations of kiln-dried wood blocks. These must be prepared with high dimensional accuracy and adequate surface quality following specific technical requirements for lamellae thickness variations, especially in the upper layers of the glued composite parquet. The accuracy of oak...
-
A framework for risk matrix design: A case of MASS navigation risk
PublicationRisk matrix, a tool for visualizing risk assessment results, is essential to facilitate the risk communication and risk management in risk-based decision-making processes related to new and unexplored socio-technical systems. The use of an appropriate risk matrix is discussed in the literature, but it is overlooked for emerging technologies such as Maritime Autonomous Surface Ships (MASS). In this study, a comprehensive framework...
-
BINDER COURSES USING COLD RECYCLED MIXTURES – A NOVEL CONCEPT IN COLD RECYCLING
PublicationCold recycling with cement and bituminous emulsion is one of the most environmentally friendly techniques to maximize the reuse of reclaimed asphalt (RA) collected during demolition of roads. Cold recycled mixtures are commonly used for base courses in construction or rehabilitation of flexible and semi-rigid pavements. Current experiences demonstrated that cold recycling with appropriate requirements and technical recommendations...
-
Evaluating the influence of radiative heat flux on convective heat transfer from a vertical plate in air using an improved heating plate
PublicationThis article examines the influence of radiative heat flux on the accuracy of the results of free convective heat transfer in air. In order to carry out these tests, based on the experience gained during the operation of a plate heated on one side, compensated by a reverse heat loss flux counter-heater, a unique double-sided heating sandwich plate was designed and built, consisting of three thin epoxy resin plates reinforced with...
-
Magnetic nanocomposites for biomedical applications
PublicationTissue engineering and regenerative medicine have solved numerous problems related to the repair and regeneration of damaged organs and tissues arising from aging, illnesses, and injuries. Nanotechnology has further aided tissue regeneration science and has provided outstanding opportunities to help disease diagnosis as well as treat damaged tissues. Based on the most recent findings, magnetic nanostructures (MNSs), in particular,...
-
Comparative wear test of journal sliding bearings with sintered bronze and Babbitt alloy bushes lubricated by environmentally acceptable/adapted lubricants (EAL)
PublicationA growing awareness of the negative effects of mineral oils on the natural environment has resulted in the introduction of new regulations related to environmental protection. One of these regulations requires the use of environmentally acceptable/adapted lubricants (EAL) to lubricate marine main shaft bearings, in place of the mineral lubricating oils that have been used for decades. Classification Societies, which supervise...
-
Additive Manufacturing as a Solution to Challenges Associated with Heat Pipe Production
PublicationThe aim of this review is to present the recent developments in heat pipe production, which respond to the current technical problems related to the wide implementation of this technology. A novel approach in HP manufacturing is to utilise hi-tech additive manufacturing techniques where the most complicated geometries are fabricated layer-by-layer directly from a digital file. This technology might be a solution to various challenges...
-
Road texture influence on tyre rolling resistance
PublicationTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Innovative system for energy collection and management integrated within a photovoltaic module
PublicationThe dynamic development of battery technology and design based on the flow of lithium ions, mainly driven by the needs of the automotive industry, leads to the conclusion that these batteries are becoming a more viable alternative to traditional lead-acid batteries. Their use is driven by the ability to quickly charge and discharge, a higher durability, maintenance-free operation, much smaller dimensions and lighter weight. The...
-
Enhancing environmental literacy through urban technology-based learning. The PULA app case
PublicationThis study addresses the need to enhance environmental literacy, focusing on urban adults through mobile applications, based on the example of PULA app that engages early adopters in gamified pro- environmental activities, offering insights into informal learning. Grounded in 'urban pedagogy,' the study combines semi-structured interviews with 17 application testers and quantitative data analysis, unveiling motivations, user feedback,...
-
Evaluation of Machine Learning Methods for the Experimental Classification and Clustering of Higher Education Institutions
PublicationHigher education institutions have a big impact on the future of skills supplied on the labour market. It means that depending on the changes in labour market, higher education institutions are making changes to fields of study or adding new ones to fulfil the demand on labour market. The significant changes on labour market caused by digital transformation, resulted in new jobs and new skills. Because of the necessity of computer...
-
The Use of Liquid Crystal Thermography in Selected Technical and Medical Applications—Recent Development
PublicationThermochromic liquid crystals (TLC) and true-colour digital image processing have been successfully used in non-intrusive technical, industrial and biomedical studies and applications. Thin coatings of TLC at surfaces are utilized to obtain detailed temperature distributions and heat transfer rates for steady or transient processes. Liquid crystals also can be used to make the temperature and velocity fields in liquids visible...
-
Transformation of the countryside into an open-air museum as a way to rescure its spatial layout and to improve the quality of live = Przekształcenie wsi w muzeum na wolnym powietrzu jako sposób ratowania jej układu przestrzennego i poprawy jakości życia mieszkańców
PublicationSince the first open-air museums until today, the exposition subject-matter has been specialized (ethnographic, archeological, industrial and technical skansens). But idea of the existence of such objects remains unchanged. Still, the goal is to show the collection of wooden buildings in the environment as close to their origin as possible or in the home environment. These distinguish the skansens and make them different then municipal...
-
Diagnostic Model of Crankshaft Seals
PublicationT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
Sphere Drive and Control System for Haptic Interaction With Physical, Virtual, and Augmented Reality
PublicationA system for haptic interaction with physical, virtual, and augmented realities, founded on drive and measurement elements (DMEs), is considered. The system consists of eight DME rolls equipped with linear actuators, able to measure their angular velocity, drive the sphere, and adjust downforce (pressing the roll against the sphere). Two modeling issues are addressed. Special effort is put in to compensate for various technical...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
INFLUENCE OF TEMPERATURE ON THE TYRE ROLLING RESISTANCE
PublicationTemperature is a very important factor controlling rolling resistance of road vehicle tyres. There are at least three different temperatures that may be considered as important factors controlling thermal conditions of the rolling tyre. The most common measure of the thermal conditions during tyre rolling is ambient air temperature. The other two are: pavement temperature and “tyre” temperature. Tyre temperature is the most difficult...
-
COMPARATIVE ANALYSIS OF POINT CLOUDS OBTAINED BY TLS AND PHOTOGRAMMETRY
PublicationTechnical progress in the field of 3D modelling resulted in increasing use of such technics to create a virtual 3D models of objects. Three-dimensional spatial models are used in a wide range of applications such as inventorisation of architectural-construction, an inventorisation of archaeological sites, medicine and wide-known engineering. Spatial models are created based on the point clouds acquired with laser scanners or photogrammetry....
-
Diagnostics and monitoring of the longest span extradosed bridge in Europe
PublicationThe article presents complex diagnostic procedures applied for the purpose of behavior analysis of the extradosed bridge with the longest span in Europe that was built in 2018 in Poland. The system of health monitoring was used to: register internal forces in temporary supports, monitor concrete bonding, perform in situ diagnostics and operation tests. The bridge is a continuous four-span structure with spans theoretical lengths...
-
Scientific Collaboration, Citation and Topic Analysis of International Conference on Agile Software Development Papers
PublicationThe International Conference on Agile Software Development (XP) was established almost sixteen years ago. Based on data from Scopus database, a total of 789 papers have been published in between years of 2002 and 2018. We employed bibliometrics analysis and topic modeling with R/RStudio to analyze these published papers from various dimensions, including the most active authors, collaboration of authorship, most cited papers, used...
-
An in-depth look at the tire rubber hardness influence on tire/road noise measurements
PublicationWhen assessing the acoustic quality of a road pavement with the close-proximity (CPX) or the on-board sound intensity (OBSI) method, the rubber hardness of the reference tire substantially affects the measurement. Practical experience shows that measurement tires can get significantly harder within a single measurement season. This is why one would like to normalize measurements to a reference rubber hardness. The recently published...
-
Assessment of the usefulness of bacterial cellulose produced by Gluconacetobacter xylinus E25 as a new biological implant
PublicationBionanocellulose (BNC) is a clear polymer produced by the bacterium Gluconacetobacter xylinus. In our current study, “Research on the use of bacterial nanocellulose (BNC) in regenerative medicine as a function of the biological implants in cardiac and vascular surgery”, we carried out material analysis, biochemical analysis, in vitro tests and in vivo animal model testing. In stage 1 of the project, we carried out physical and...
-
IoT for healthcare applications
PublicationThis chapter summarizes IRACON contributions related to the application of IoT in healthcare. It consists of the following three sections. Section 8.1 presents the measurement campaigns and the related statistical analysis to obtain various channel models for wearable and implantable devices. In addition, the importance of physical human-body phantoms used for channel, Specific Absorption Rate (SAR), and Electromagnetic (EM) exposure...
-
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
Incorporating installation effects into the probability analysis of controlled modulus columns
PublicationThis technical report presents the probabilistic analysis which integrates the Monte Carlo simulation (MCS) with random field theory to model the load–displacement behavior of Controlled Modulus Columns (CMCs) in overconsolidated Poznań clay. Presented study focuses on the practical aspects of statistical analysis of geotechnical data, numerical model development, and results evaluation. Variability and spatial distribution of...
-
Fault detection in the marine engine using a support vector data description method
PublicationFast detection and correct diagnosis of any engine condition changes are essential elements of safety andenvironmental protection. Many diagnostic algorithms significantly improve the detection of malfunctions.Studies on diagnostic methods are rarely reported and even less implemented in the marine engine industry.To fill this gap, this paper presents the Support Vector Data Description (SVDD) method as applied to thefault detection...
-
Future opportunities for products derived from black soldier fly (BSF) treatment as animal feed and fertilizer - A systematic review
PublicationThe pursuit of novel food products with good nutritional value for both direct and indirect human consumption is crucial. Given the nutritional benefits of insects and the sustainability of this sort of farming, using them as food for farmed animals is a promising alternative. In this regard, the black soldier fly (Hermetia illucens) is most capable of efficiently converting a wide variety of organic materials, from food waste...
-
Influence of finishing colour on the efficiency of automated production line for wooden doors
PublicationPorta KMI Poland S.A. company has implemented a fully automated intelligent technological line TechnoPORTA for customized mass-production of technical door leaves. Each door leaf is provided with a unique QR code. It allows the line modules to individually adjust the machining parameters to the currently processed element according to the IT controlling system. Before en-tering the TechnoPorta line, the door leaves are not sorted,...
-
Analysis of AC/DC/DC Converter Modules for Direct Current Fast-Charging Applications
PublicationThe paper is a comprehensive laboratory comparison study of two galvanic isolated solution off-board battery chargers: (1) Si-based cost-effective case, and (2) SiC-bidirectional ready for vehicle to grid concept case. All circuits are modular, and in both cases the DC/DC converter can be replaced according to the end user requirements (the coupled transformer remains the same and is constructed based on 12xC100 cores to avoid...
-
The Development of a Conceptual Framework for Knowledge Sharing in Agile IT Projects
PublicationOrganizations must adapt their resources to meet the challenges associated with changes in the work environment in order to remain competitive in the information era. Several research findings identify knowledge sharing as a means for an organization to improve its competitiveness. Knowledge sharing can be defined in a variety of ways, but it essentially refers to the exchange of knowledge from an information giver to an information...
-
Sharing research data across disciplines
PublicationThis monograph is a collection of experiences gathered by the team implementing the Bridge of Data project. However, it is not just a simple summary of the project implementation. It shows and systematizes the substantive and technical works performed by the teams and several issues related to data management itself in various disciplines, represented by members of the scientific team and other researchers from partner universities.The...
-
A Method for The Assessing of Reliability Characteristics Relevant to an Assumed Position-Fixing Accuracy in Navigational Positioning Systems
PublicationThis paper presents a method which makes it possible to determine reliability characteristics of navigational positioning systems, relevant to an assumed value of permissible error in position fixing. The method allows to calculate: availability , reliability as well as operation continuity of position fixing system for an assumed, determined on the basis of formal requirements - both worldwide and national, position-fixing accuracy....
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
INVESTIGATIONS OF THE LABORATORY FARYMANN DIESEL ENGINE D10 TYPE BY MEANS OF A LANGMUIR PROBE
PublicationA precise determination of the crankshaft angular position, at which fuel ignition occurs in the SI engine, enables credible diagnosis of the technical state of its working space as well as of the fuel feed system. An observation of the Langmuir probe signal provides entirely new possibilities for engine diagnostics. The probe is introduced into the working space of a cylinder through its indicator valve. This paper presents the...
-
Innovative Gathering and Energy Management System Integrated within PV Module
PublicationThe dynamic development of battery technology and design based on the flow of lithium ions, mainly driven by the needs of the automotive industry leads to the Conclusion That they are becoming a more viable alternative to traditional lead-acid batteries. Their use is driven by the ability it quickly charge and discharge times higher durability, maintenance-free operation and much smaller dimensions as well as weight. The emergence...
-
Wavelet transform-based approach to defect identification in railway carbon contact strips.
PublicationPantographs of electric rail vehicles are fitted with carbon contact strips, which slide along the contact wire of catenary to provide constant electrical contact. Contact strips are exposed to wear and damages. Using damaged contact strips significantly increases the risk of catenary rupture. Therefore, their technical condition has to be inspected frequently. In previous work a 3D laser scanning system was proposed for recording...
-
Nonlinear properties of the Gotland Deep – Baltic Sea
PublicationThe properties of the nonlinear phenomenon in water, including sea water, have been well known for many decades. The feature of the non homogeneous distribution of the speed of sound along the depth of the sea is very interesting from the physical and technical point of view. It is important especially in the observation of underwater area by means of acoustical method ( Grelowska et al ., 2013; 2014). The observation of the underwater...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes - experimental study
PublicationIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. The aim of this paper is to investigate experimentally the behaviour of horizontally deformed columns (deformation...
-
Analysis of GNSS, Hydroacoustic and Optoelectronic Data Integration Methods Used in Hydrography
PublicationThe integration of geospatial data in hydrography, performed using different measurement systems, involves combining several study results to provide a comprehensive analysis. Each of the hydroacoustic and optoelectronic systems is characterised by a different spatial reference system and the method for technical implementation of the measurement. Therefore, the integration of hydrographic data requires that problems in selected...
-
Analyzing and Visualizing Government-Citizen Interactions on Twitter to Support Public Policy-making
PublicationTwitter is widely adopted by governments to communicate with citizens. It has become a major source of data for analyzing how governments communicate with citizens and how citizens respond to such communication, uncovering important insights about government-citizen interactions that could be used to support public policy-making. This article presents research that aims at developing a software tool called Twitter Analytics for...
-
Visual method for detecting critical damage in railway contact strips
PublicationEnsuring an uninterrupted supply of power in the electric traction is vital for the safety of this important transport system. For this purpose, monitoring and diagnostics of the technical condition of the vehicle's power supply elements are becoming increasingly common. This paper presents a new visual method for detecting contact strip damage, based on measurement and analysis of the movement of the overhead contact line (OCL)...
-
Detail, Facture, and Colour in the Architecture of Polish Single-Family Houses after 1989
PublicationThe article presents single-family houses architecture transformations since 1989, with particularly close attention paid to the significance of detail, facture, and colour. The article presents the architecture as an art of designing and building facilities with both use and aesthetic value, an art of shaping space and building forms. Architectural work should correspond to the intended function, technique, economic and aesthetic...
-
Mechanical characteristics of welded joints between different stainless steels grades
Publicationnvestigation of mechanical characteristics of welded joints is one of the most important tasks that allow determining their functional properties. Due to the very high, still rising, cost of some stainless steels it is justified, on economic grounds, welding austenitic stainless steel with steels that are corrosion-resistant like duplex ones. According to forecasts the price of...
-
Analysis of the relationship between the length of eye fixation and the parameters of advertisements visible from the road
PublicationIn Poland, many advertising signs addressed to motorists are located along the roadside. Advertisements do not serve any traffic related purpose and can distract drivers making them less reliable and as a consequence, reduce road safety. The existing regulations only apply to the carriageway. The research is conducted as part of the RID project. The objective of the RID project is to create a "Manual for positioning roadside advertising...
-
Modelling of sequencing batch reactor operating at various aeration modes
PublicationThe presented study involved designing a computer model of a sequencing batch reactor (SBR) at laboratory scale. The data pertaining to the technical aspects of the bioreactor and quality indicators of wastewater constituted the input for the employed simulation tool, i.e. GPS-X software package. The results of a simulation involving a 12-hour operation cycle are presented in this work; each cycle included 6 phases: filling, mixing,...
-
Smartphones as tools for equitable food quality assessment
PublicationBackground: The ubiquity of smartphones equipped with an array of sophisticated sensors, ample processing power, network connectivity and a convenient interface makes them a promising tool for non-invasive, portable food quality assessment. Combined with the recent developments in the areas of IoT, deep learning algorithms and cloud computing, they present an opportunity for advancing wide-spread, equitable and sustainable food...
-
State of the Art in Open Platforms for Collaborative Urban Design and Sharing of Resources in Districts and Cities
PublicationThis work discusses recent developments in sharing economy concepts and collaborative co-design technology platforms applied in districts and cities. These developments are being driven both by new technological advances and by increased environmental awareness. The paper begins by outlining the state of the art in smart technology platforms for collaborative urban design, highlighting a number of recent examples. The case of peer-to-peer...
-
Quality assessment of low voltage surge arresters
PublicationUsers expect reliable operation of the surge arrester during overvoltages, which may originate from a switching process or a lightning discharge. The necessary conditions to guarantee these expectations are: appropriate construction of the surge arrester, its production being maintained in accordance with technical standards, and a positive results of the type test (as well routine and acceptance tests). The recipient, especially...
-
On Rapid Design Optimization and Calibration of Microwave Sensors Based on Equivalent Complementary Resonators for High Sensitivity and Low Fabrication Tolerance
PublicationThis paper presents the design, optimization, and calibration of multivariable resonators for mi-crowave dielectric sensors. An optimization technique for circular complementary split ring reso-nator (CC-SRR) and square complementary split ring resonator (SC-SRR) is presented to achieve the required transmission response in a precise manner. The optimized resonators are manufac-tured using a standard photolithographic technique...