Filters
total: 1255
filtered: 1056
displaying 1000 best results Help
Search results for: ULTRA-RAPID DISPLACEMENT
-
Improvement of Performance Level of Steel Moment-Resisting Frames Using Tuned Mass Damper System
PublicationIn this paper, parameters of the tuned mass dampers are optimized to improve the performance level of steel structures during earthquakes. In this regard, a six-story steel frame is modeled using a concentrated plasticity method. Then, the optimum parameters of the Tuned Mass Damper (TMD) are determined by minimizing the maximum drift ratio of the stories. The performance level of the structure is also forced to be located in a...
-
An Intergrated Model of Motion, Steering, Positioning and Stabilization of an Unmanned Autonomous Maritime Vehicle
PublicationIn the paper the aim of an interdisciplinary research is presented. The research method is introduced. An object the unmanned autonomous maritime vehicle is briefly described. The key research problem concerns a combined model of the vehicle motion including the loads of lift and hydrodynamic nature. The model takes into account the gravity and displacement forces, resistance and thrust forces, lift and other hydrodynamic forces....
-
A Direct Modulation for Matrix Converters based on the Onecycle Atomic operation developed in Verilog HDL.
PublicationThis paper presents a fast direct Pulse Width Modulation (PWM) algorithm for the Conventional Matrix Converters (CMC) developed in Verilog Hardware Description language (HDL). All PWM duty cycle calculations are performed in one cycle by an atomic operation designed as a digital module using FPGA basic blocks. The algorithm can be extended to any number of output phase. The improved version of the discontinuous Direct Analytic...
-
The analysis of the determination of points positions using photogrammetric methods
PublicationThis article was created as a result of research conducted within the master thesis. The purpose of the research was to analyze the accuracy of determining the actual position of the photographed points according to the calculated parameters. The accuracy of photos alignment was determined as parameters, which determine their external and internal orientation. In order to determine the location of the determined points, it was...
-
CONSTRUCTION TECHNOLOGY OF TIMBER-FRAME HOUSES RESISTANT TO DYNAMIC LOADS – STUDY ON MODELS OF EXTERIOR WALLS
PublicationThe aim of this paper is to show the numeric representation of experimental studies concerning the behaviour of exterior wall models of a timber-frame house under harmonic loading. A single wall model according to traditional technology of timberframe house walls (filling with mineral wool) was tested. The analysis was conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified...
-
Experimental study of the effect of vertical acceleration component on the slope stability
PublicationThe paper deals with the stability of earth dams subjected to seismic and paraseismic excitations occurring in the close distance to the dam. The Newmark’s stability approach, classified as a simplified dynamic method, has been extended for two directional dynamic loading case and the evolution of the friction coefficient. The paper is focused on the experimental verification of the proposed method for harmonic and cyclic excitations...
-
LDFEM analysis of FDP auger installation in cohesive soil
PublicationThis paper deals with large deformation finite element (LDFE) preliminary modelling of Full Displacement Pile (FDP) installation in cohesive soil deposit located in Jazowa, Poland. The detailed FDP auger geometry is applied and the drilling process is modelled with full 3D Coupled Eulerian-Lagrangian (CEL) formulation. The total stress approach and elastic-perfectly plastic model with rate-dependent Mises plasticity is used. The...
-
Timber frame houses resistant to dynamic loads - seismic analysis
PublicationThe aim of the article is to present results of seismic analysis results of two real-sized timber frame buildings subjected to seismic excitations. The first model was insulated with mineral wool, the second one with polyurethane foam. Technology and specifications involved in both models construction is based on the previously conducted experimental research on timber frame houses, including wall panels tests, wall numerical models...
-
3D Monitoring - Identification of measurement problems at larger movements of the tracked points
PublicationAuthors identified the problems associated with the determination of the controlled points coordinates by use of automated Total Station placed behind transparent barrier. Important thing in the mentioned analysis was a large change of controlled points position and not stable Total Station’s stand (because of stand’s thermal drift). This two elements, combined with measurement made through glass plate determine the need for impact...
-
Two-dimensional simulations of concrete fracture at aggregate level with cohesive elements based on X-ray lCT images
PublicationThe paper presents results of two-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 4-phase material composed of aggregate grains placed in the cement matrix, interfacial transitional zones (ITZs) and macro-voids. The particle distribution was taken from real concrete beams on the basis of X-ray lCT images. Comprehensive numerical analyses were carried...
-
Determination of the substances potentially allergenic in water
PublicationPersonal care chemicals are continuously released into environment through domestic and industrial wastewater, causing adverse effects on human health. Their presence can be detected in different environmental compartments. A group of chemicals included in most personal care products are the allergen fragrances. In the present work, simple and rapid methodology based on ultrasound-assisted emulsification-microextraction (USAEME)...
-
REVITALIZATION PROJECT OF SLUM TRANSFORMATION: A CASE STUDY HAY-AL TANAK,BEIRUT,LEBANON
PublicationSlums are global phenomena that exist as a solution for those who couldn’t afford a house. This phenomenon is growing accompanying the rapid urbanization and the growth of the urban population, three-quarter of the world population anticipated to live in an urban environment by 2050 (Avis, 2016, p. 57). This paper reviews slum's evaluation of the revitalization project for one of the poorest slums in Beirut called Hay-Al Tanak....
-
On DoA estimation for rotating arrays using stochastic maximum likelihood approach
PublicationThe flexibility needed to construct DoA estimators that can be used with rotating arrays subject to rapid variations of the signal frequency is offered by the stochastic maximum likelihood approach. Using a combination of analytic methods and Monte Carlo simulations, we show that for low and moderate source correlations the stochastic maximum likelihood estimator that assumes noncorrelated sources has accuracy comparable to the...
-
Human Centric Lighting. The New X Factor?
PublicationWe live in challenging times, and one could even claim we’re experiencing a revolution in lighting with LED technology taking over the world. Part of this rapid change involves a concept called Human Centric Lighting (HCL). In Frankfurt this year, during Light+Building, it was the buzzword, with nearly every second manufacturer’s stand claiming they had figured out the special formula necessary to create perfect HCL illumination....
-
Fast multi-criterial statistical analysis and design optimization of compact microwave couplers
Publication—A rapid statistical analysis and yield estimation of compact microwave couplers involving multiple performance parameters has been presented. The analysis is realized using a fast surrogate model representing appropriate characteristic points of the coupler response. Because of less nonlinear dependence of the characteristic points on the structure geometry (compared to the original response, i.e., S-parameters vs. frequency),...
-
Assessment of the Steering Precision of a Hydrographic Unmanned Surface Vessel (USV) along Sounding Profiles Using a Low-Cost Multi-Global Navigation Satellite System (GNSS) Receiver Supported Autopilot
Publicationhe performance of bathymetric measurements by traditional methods (using manned vessels) in ultra-shallow waters, i.e., lakes, rivers, and sea beaches with a depth of less than 1 m, is often difficult or, in many cases, impossible due to problems related to safe vessel maneuvering. For this reason, the use of shallow draft hydrographic Unmanned Surface Vessels (USV) appears to provide a promising alternative method for performing...
-
Perfect thermal contact of hyperbolic conduction semispaces with an interfacial heat source
PublicationThe problem of thermal contact between two bodies with a heat source at their interface presents great scientific and practical interest. On the time scale of a nanosecond or shorter, heat propagation should be considered in the form of thermal waves of finite speeds. This study investigated the thermal behaviour of hyperbolic conduction semispaces in perfect thermal contact subjected to the action of an interfacial heat source....
-
Miniaturized Metal-Mountable U-shaped Inductive-Coupling-Fed UHF RFID Tag Antenna with Defected Microstrip Surface
PublicationThis study presents a novel miniature ultra-high frequency (UHF) radio frequency identification (RFID) tag for metallic objects. Its arrangement includes a U-shaped feeder, which is inductively coupled to two E-type connected patches. Size reduction is achieved by means of utilizing the U-shaped feeder, and introducing a defection in the connection between the two E-type patches. The defection in the connection area between the...
-
New achievements in the field of extraction of trace analytes from samples characterized by complex composition of the matrix
PublicationWithout any doubt, the monitoring of compounds present in samples at trace or ultra-trace level usually requires a preliminary step of isolation and/or enrichment of analytes due to the fact that majority of analytical techniques are not sensitive enough for direct determination of trace compounds. On the other hand, sample preparation is considered as crucial part of whole analytical procedures, in particular in samples characterized...
-
COMPARISON OF THE ABRASION RESISTANCE OF THE SELECTED BIOMATERIALS FOR FRICTION COMPONENTS IN ORTHOPEDIC ENDOPROSTHESES
PublicationRosnące z każdym rokiem zapotrzebowanie na endoprotezy stawów ortopedycznych przy jednoczesnym dążeniu do zwiększenia ich trwałości i wyeliminowania negatywnych skutków ubocznych produktów zużycia, które mogą wywoływać proces zapalny w tkankach determinuje potrzebę poszukiwania nowych biomateriałów, bądź metody modyfikacji ich powierzchni. Nadrzędnym celem prowadzonych przez nas badań było oszacowanie intensywności zużycia ściernego...
-
Modelling of laminated glass PVB walls of buildings exposed to vehicle impact with different speeds
PublicationThis paper presents an analytical model, developed for laminated glass subjected to a low-velocity impact. It has the ability to capture glass cracks as well as large non-linear deformations. It is based mathematically on the firstorder deformation concept, which considers the effect of membrane and transverse shear as well as bending. This theory uses damage mechanics to capture the glass cracking. For this purpose, several experiments...
-
The role of ergonomics in architectonic and marketing operations
PublicationThe 20th century, along with the development of mass culture, brought a rapid increase of marketing communications significance. At first, this branch of art had an informational function associated with advertising operations. Nowadays, an increase of marketing specialists’ interest in influencing a human being by the space they stay in may be observed. Ergonomics plays an important role in such operations. The aim of this article...
-
Recognition and sensing of anions
PublicationMolecular ion recognition is one of the most intensively studied areas of supramolecular technology. The reason for this is the essential role that ions play in many biological as well as industrial processes. On the other hand, however, it has been proved that ions can have a negative impact on human health and the environment. For these reasons, it is extremly important to develop rapid and simple methods allowing the determination...
-
Evaluation of the structures size in the liquid-gas flow by gamma-ray absorption
PublicationThe rapid development of tomography methods particularly electrical, X and gamma rays allows for a wide range of the information about flow structure. However, all of such methods are quite complicated. At the same time much simpler systems as the measuring system of gamma rays absorption, allows to obtain a all key flow information which describe the two-phase flow. In the article the results of analyzes of radiometric signal...
-
Modelling the malware propagation in mobile computer devices
PublicationNowadays malware is a major threat to the security of cyber activities. The rapid develop- ment of the Internet and the progressive implementation of the Internet of Things (IoT) increase the security needs of networks. This research presents a theoretical model of malware propagation for mobile computer devices. It is based on the susceptible-exposed- infected-recovered-susceptible (SEIRS) epidemic model. The scheme is based on...
-
Electronic noses in classification and quality control of edible oils: A review
PublicationThe growing demand for wholesome and nutritious food leads to intensification of production, which in turn can have a detrimental effect on quality and well-being of consumers. For that reason, it is important to develop novel methods of food control which would be characterized by a short time of analysis, adequate sensitivity and relatively low cost. One such technique involves the use of multi-sensory devices called electronic...
-
Satelitowy agregat pompowy
PublicationW artykule opisano najnowszą konstrukcję satelitowego agregatu pompowego charakteryzującego się tym, że pompa satelitowa jest umieszczona wewnątrz silnika elektrycznego i zasysa ciecz poprzez otwór wydrążony osiowo w wale silnika. Zastosowana w agregacie pompa satelitowa jest nowatorską konstrukcją zawierającą mechanizm satelitowy o odwróconej kinematyce znamienny tym, że planeta (wirnik) oraz płyty kompensacyjne (rozrządu) są...
-
Badania stanu technicznego ścianek szczelnych strony południowej i północnej komory południowej śluzy Dzierżno
PublicationPrace dotyczyły badań nieniszczących łączników (zamków) Paine`a oraz ścianek szczelnych. Ściany boczne komory południowej śluzy Dzierżno zbudowane są ze stalowych pasów blachy o grubości około 16mm i długości 22m połączonych ze sobą wzdłuż dłuższej krawędzi za pomocą zamków Peine`a. System ten umożliwia uzyskanie szczelnego połączenia na całej długości ścianki. Zaawansowany proces korozji spowodował rozszczelnienie połączenia...
-
Porównanie obciążenia wiatrem wyznaczonego na podstawie procedur normowych z wynikami symulacji w cyfrowym tunelu aerodynamicznym dla hali stalowej.
PublicationW niniejszych badaniach porównano obciążenia od wiatru wyznaczonego metodą normową oraz w cyfrowym tunelu aerodynamicznym. Analizom poddano typowy budynek hali na planie prostokąta z dwuspadowym dachem w czterech wariantach geometrycznych. W pierwszym etapie budynki zwymiarowano bazując na obciążeniach od wiatru wyznaczonych według Eurokodu. Następnie dla poszczególnych elementów konstrukcyjnych określono poziom wytężenia. Dla...
-
Developing a methodology for model tests of floating platforms in a towing tank of low depth
PublicationThe paper presents two ways to mooring model of semi-submersible platform for research in the small depth towing pool. The tested model was made in the likeness of 1:100 Thunder Horse platform moored in the Gulf of Mexico at a depth of 1,920 m. Its mooring system consisted of 16 semi-taut mooring lines (chain-wire-chain) spaced Star-shape and attached at the bottom to the suction piles. The tests were performed in the towing pool...
-
Technical diagnostics and monitoring of traction current collectors
PublicationNew evaluation methods of the technical condition of rolling stock current collectors are proposed in this paper. The method of automatic measurement of the pantograph static force characteristic, realized when the vehicle runs through the test section of the track with especially prepared overhead line height distribution, has been practically implemented by the Polish Railways. The method of testing the slipper spring suspension...
-
Numerical investigations of discrete crack propagation in Montevideo splitting test using cohesive elements and real concrete micro-structure
PublicationThe paper is aimed at accurately predicting the discrete fracture process in concrete specimens under complex stress states in two dimensional (2D) simulations. Plain concrete specimens subjected to Montevideo splitting test (MVD) were used for consideration due to non-negligible shear stresses impact in this type of test. In order to reflect the heterogeneous nature of the concrete, the meso-structure of the samples was included...
-
Stress-driven nonlocal elasticity for nonlinear vibration characteristics of carbon/boron-nitride hetero-nanotube subject to magneto-thermal environment
PublicationStress-driven nonlocal theory of elasticity, in its differential form, is applied to investigate the nonlinear vibrational characteristics of a hetero-nanotube in magneto-thermal environment with the help of finite element method. In order to more precisely deal with the dynamic behavior of size-dependent nanotubes, a two-node beam element with six degrees-of freedom including the nodal values of the deflection, slope and curvature...
-
On the Dynamics of a Visco–Piezo–Flexoelectric Nanobeam
PublicationThe fundamental motivation of this research is to investigate the effect of flexoelectricity on a piezoelectric nanobeam for the first time involving internal viscoelasticity. To date, the effect of flexoelectricity on the mechanical behavior of nanobeams has been investigated extensively under various physical and environmental conditions. However, this effect as an internal property of materials has not been studied when the...
-
Transient response of oscillated carbon nanotubes with an internal and external damping
PublicationThe present works aims at modeling a viscoelastic nanobeam with simple boundary conditions at the two ends with the introduction of the Kelvin-Voigt viscoelasticity in a nonlocal strain gradient theory. The nanobeam lies on the visco-Pasternak matrix in which three characteristic parameters have a prominent role. A refined Timoshenko beam theory is here applied, which is only based on one unknown variable, in accordance with the...
-
A selectively reduced degree basis for efficient mixed nonlinear isogeometric beam formulations with extensible directors
PublicationThe effect of higher order continuity in the solution field by using NURBS basis function in isogeometric analysis (IGA) is investigated for an efficient mixed finite element formulation for elastostatic beams. It is based on the Hu–Washizu variational principle considering geometrical and material nonlinearities. Here we present a reduced degree of basis functions for the additional fields of the stress resultants and strains...
-
Buckling and shape control of prestressable trusses using optimum number of actuators
PublicationThis paper describes a method to control the nodal displacement of prestressable truss structures within the desired domains. At the same time, the stress in all members is unleashed to take any value between the allowable tensile stress and critical buckling stress. The shape and stresses are controlled by actuating the most active members. The technique considers the members’ initial crookedness, residual stresses, and slenderness...
-
Nonlinear planar modeling of massive taut strings travelled by a force-driven point-mass
PublicationThe planar response of horizontal massive taut strings, travelled by a heavy point-mass, either driven by an assigned force, or moving with an assigned law, is studied. A kinematically exact model is derived for the free boundary problem via a variational approach, accounting for the singularity in the slope of the deflected string. Reactive forces exchanged between the point-mass and the string are taken into account via Lagrange...
-
Effect of underwater wet welding conditions on the diffusible hydrogen content in deposited metal
PublicationIn the study mercury displacement method was used for determination of diffusible hydrogen amount in deposited metal obtained during underwater wet welding with covered electrodes in laboratory conditions according to a two-level full factorial design for three factors. The factors and their levels were chosen among conditions and parameters of welding in accordance with the results of own preliminary studies. A statistical analysis...
-
Experimental verification of visual method for measuring displacements of contact line elements
PublicationThe increase of rail vehicles speed, as well as the increase of their power, puts high demands on the power delivery system for traction vehicles The most critical point in the vehicle's power supply circuit is the contact between the current collector and contact wires. Ensuring a reliable co-operation of the current collector and contact line, requires technical development...
-
Analysis of hydrodynamic pressure fields of motorboats and pontoons in shallow water
PublicationThe article presents the results of calculations of the pressure fields generated by a motorboat at the bottom of a shallow sea. Calculations were made using the boundary elements method (BEM), arranged on the surface of the boat and the bottom of the sea. This method is described in [3], and applied on a free surface linearized boundary condition. Results for four different lengths of motorboats, from 2.85 m to 9.5 m, sea depth...
-
The basics of design and experimental tests of the commutation unit of a hydraulic satellite motor
Publicationhe article presents an analytical method to design the commutation unit in a hydraulic satellite motor. It is shown that the size of the holes feeding the working chambers and their location on the plates closing those chambers depends on the geometrical dimensions of the working mechanism. The overlap in the commutation unit depends on the rotational speed range. It is demonstrated that the geometrical dimensions of the commutation...
-
New generation of the satellite hydraulic pumps
PublicationHydraulic satellite machines are known and produced in many versions, recognizable by the number of humps on their inner rotor and external gear, and therefore by the number of cooperating gears (satellites). All known shapes were however designed on the base of preliminary assumption that rotor’s and external gear’s pitch lines are formed by merging arcs, tangent to each other in the. This assumption makes calculations easier,...
-
Study on the Positioning Accuracy of the GNSS/INS System Supported by the RTK Receiver for Railway Measurements
PublicationCurrently, the primary method for determining the object coordinates is positioning using Global Navigation Satellite Systems (GNSS) supported by Inertial Navigation Systems (INS). The main goal of this solution is to ensure high positioning availability, particularly when access to satellite signals is limited (in tunnels, areas with densely concentrated buildings and in forest areas). The aim of this article is to determine whether...
-
STORMWATER AS AN ALTERNATIVE WATER SOURCE: QUALITY CHANGES WITH RAINFALL DURATION AND IMPLICATIONS FOR TREATMENT APPROACHES
PublicationThe pressure on the world’s water resources is rapidly increasing due to population growth and climatic changes. Valorisation of stormwater as a water resource for non-potable reuse can reduce high-quality water demands and save it for potable uses. In this context, not only roof runoff but also drained stormwater outflow, representing considerably higher pollution levels, should be considered as a potential resource. We analysed...
-
Three-dimensional Web Geographic Information System using web-based technologies
PublicationWeb-based Geographic Information Systems offer a way of delivering geographic information to devices with small computational power, such as smartphones. In recent years, the rapid development of the Web Graphics Library (WebGL) made it possible to create rich interactive applications running inside a web browser and displaying three-dimensional objects using hardware acceleration. This paper presents a three-dimensional Web-GIS...
-
Mobility Management Solutions for IP Networks Comparative Analysis of IP-based Mobility Protocols and Handover Algorithms Invited Paper
PublicationA rapid growth of IP-based networks and services hascreated a vast collection of resources and functionalities availableto users by means of a uniform method of access offered by the IPprotocol. At the same time, advances in the design of mobileelectronic devices allowed them to reach a utility levelcomparable to desktop computers, while still retaining theirmobility advantage. Unfortunately, the base IP protocol does notperform...
-
Sample preparation and recent trends in volatolomics for diagnosing gastrointestinal diseases
PublicationThe analysis of the human volatilome can be successfully used for rapid and non-invasive diagnostics of gastrointestinal diseases. However, the introduction of techniques based on detection of volatiles is limited, among other factors, by difficulties which arise during the sampling stage and instrumental analysis. The aim of this article was to review and discuss medical and analytical literature on the analysis of volatiles in...
-
Education of Logisticians in Poland: Problems and Prospects in Students’ Opinion
PublicationLogistics is one of the key sectors of the Polish economy. Its value reflects not only its own capacity, but also the role it plays in ensuring the proper functioning of the entire economy. The rapid development of the industry and the highest demands on logistics solutions bring to the fore the problem of preparing a new generation of specialists in logistics. That is why the question of compliance to learning expectations of...
-
Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters
PublicationBuffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more...