Search
Filters
total: 3451
filtered: 2293
displaying 1000 best results Help
Search results for: connected dominating set
-
OPERATION OF TWO-SHAFT GAS TURBINE IN THE RANGE OF OPEN ANTI-SURGE VALVE
PublicationThis paper presents experimental tests of full-scale two-shaft gas turbine in the range of open anti-surge valve (ASV). The tests were carried out in a laboratory gas- turbine test stand belonging to Department of Automation and Power Engineering , Faculty of Ocean Engineering and Ship Technology , Gdańsk University of Technology. The tests covered the start-up and low load operation of the turbine set in the range of open...
-
Review of sewage sludge management: standards, regulations and analytical methods
PublicationThis article presents the most popular methods of sewage sludge management and associated unit operations and processes referring to them. The most popular methods are: Reclamation and adaptation of lands to specific needs; plant cultivation not intended for consumption or for production of food; usage in agriculture; usage in building; recovery of phosphorus, rare earth metals or fats and usage in industry; producing combustible...
-
Fast multi-objective optimization of antenna structures by means of data-driven surrogates and dimensionality reduction
PublicationDesign of contemporary antenna structures needs to account for several and often conflicting objectives. These are pertinent to both electrical and field properties of the antenna but also its geometry (e.g., footprint minimization). For practical reasons, especially to facilitate efficient optimization, single-objective formulations are most often employed, through either a priori preference articulation, objective aggregation,...
-
Znaczenie różnorodności w wirtualnej współpracy
PublicationRóżnorodność jest jedną z podstawowych cech zespołów wirtualnych. Odnosi się ona do geograficznego rozproszenia członków zespołu, różnic stref czasowych, w których pracują, zróżnicowania narodowogo i kulturowego, ale również do pracy dla różnych organizacji, pełnienia różnych ról zespołowych o odpowiedzialności za różne części realizowanego projektu. Artykuł dotyczy najważniejszych wymiarów różnorodności istotnych dla wirtualnej...
-
Kluczowe kompetencje jako narzędzie do tworzenia nowych modeli biznesu w przedsiębiorstwach
PublicationKoncepcja kluczowych kompetencji wywodzi się z nurtu zasobowego, który zakłada, iż o efektywności i konkurencyjności każdego podmiotu decydują odpowiednio dobrane zasoby i umiejętności ich optymalnego wykorzystania. Model biznesu to narzędzie do realizacji strategii organizacji, które wspomaga rozwój oraz zarządzanie strategiczne w przedsiębiorstwie. Dysertacja wypełnia lukę, jaką było wskazanie na zależność pomiędzy kluczowymi...
-
Analysis of Video Transmission Capabilities in a Simulated OFDM-Based Supplementary BPL-PLC System
PublicationThe design and maintenance of a reliable communication system, especially in harsh working conditions for the oil and mining industry, brings many challenges. With the use of a video transmission system, one can monitor the crew and their working environment. Broadband over power line–power line communication (BPL-PLC) seems an ideal medium for such a service, since it enables the use of the existing wired infrastructure for supplementary...
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublicationWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
Contactless hearing aid designed for infants
PublicationIt is a well known fact that language development through home intervention for a hearing-impaired infant should start in the early months of a newborn baby's life. The aim of this paper is to present a concept of a contactless digital hearing aid designed especially for infants. In contrast to all typical wearable hearing aid solutions (ITC, ITE, BTE), the proposed device is mounted in the infant's bed with any parts of its set-up...
-
Computationally Efficient Multi-Objective Optimization of and Experimental Validation of Yagi-Uda Antenna
PublicationIn this paper, computationally efficient multi-objective optimization of antenna structures is discussed. As a design case, we consider a multi-parameter planar Yagi-Uda antenna structure, featuring a driven element, three directors, and a feeding structure. Direct optimization of the high-fidelity electromagnetic (EM) antenna model is prohibitive in computational terms. Instead, our design methodology exploits response surface...
-
Low-cost data-driven modelling of microwave components using domain confinement and PCA-based dimensionality reduction
PublicationFast data-driven surrogate models can be employed as replacements of computationally demanding full-wave electromagnetic simulations to facilitate the microwave design procedures. Unfortunately, practical application of surrogate modelling is often hindered by the curse of dimensionality and/or considerable nonlinearity of the component characteristics. This paper proposes a simple yet reliable approach to cost-efficient modelling...
-
Rapid multi-criterial design of microwave components with robustness analysis by means of knowledge-based surrogates
PublicationManufacturing tolerances and uncertainties concerning material parameters, e.g., operating conditions or substrate permittivity are detrimental to characteristics of microwave components. The knowledge of relations between acceptable parameter deviations (not leading to violation of design specifications) and the nominal performance (not considering uncertainties), and is therefore indispensable. This paper proposes a multi-objective...
-
Searching for the primary metabolic alterations of polycystic ovary syndrome by application of the untargeted metabolomics approach
PublicationDespite a large number of studies, the pathogenesis of polycystic ovary syndrome (PCOS) still remains unexplained. In light of ambiguous observations reported in metabolomics, there is a need to carry out studies focusing on confirming the discriminating power of the proposed metabolomics biomarkers. Our research aimed to perform a validation study of metabolites detected in our previous study from serum samples, on the new set...
-
Size reduction of ultra-wideband antennas with efficiency and matching constraints
PublicationAntenna design is a multifaceted task that involves handling of various performance figures concerning both electrical performance of the structure as well as its geometry. Simultaneous control of several objectives through rigorous optimization is very challenging and virtually impossible through conventional approaches such as parameter sweeping. In this work, we investigate size reduction of ultra‐wideband antenna structures...
-
Objectivization of phonological evaluation of speech elements by means of audio parametrization
PublicationThis study addresses two issues related to both machine- and subjective-based speech evaluation by investigating five phonological phenomena related to allophone production. Its aim is to use objective parametrization and phonological classification of the recorded allophones. These allophones were selected as specifically difficult for Polish speakers of English: aspiration, final obstruent devoicing, dark lateral /l/, velar nasal...
-
T-colorings, divisibility and circular chromatic number
PublicationLet T be a T-set, i.e., a finite set of nonnegative integers satisfying 0 ∈ T, and G be a graph. In the paper we study relations between the T-edge spans espT (G) and espd⊙T (G), where d is a positive integer and d ⊙ T = {0 ≤ t ≤ d (max T + 1): d |t ⇒ t/d ∈ T} . We show that espd⊙T (G) = d espT (G) − r, where r, 0 ≤ r ≤ d − 1, is an integer that depends on T and G. Next we focus on the case T = {0} and show that espd⊙{0} (G) =...
-
A Semiautomatic Experience-Based Tool for Solving Product Innovation Problem
PublicationIn this paper we present the idea of Smart Innovation Engineering (SIE) System and its implementation methodology. The SIE system is semi-automatic system that helps in carrying the process of product innovation. It collects the experiential knowledge from the formal decisional events. This experiential knowledge is collected from the group of similar products having some common functions and features. The SIE system behaves like...
-
Accelerated multi-objective design optimization of antennas by surrogate modeling and domain segmentation
PublicationMulti-objective optimization yields indispensable information about the best possible design trade-offs of an antenna structure, yet it is challenging if full-wave electromagnetic (EM) analysis is utilized for performance evaluation. The latter is a necessity for majority of contemporary antennas as it is the only way of achieving acceptable modeling accuracy. In this paper, a procedure for accelerated multi-objective design of...
-
Minimizing Distribution and Data Loading Overheads in Parallel Training of DNN Acoustic Models with Frequent Parameter Averaging
PublicationIn the paper we investigate the performance of parallel deep neural network training with parameter averaging for acoustic modeling in Kaldi, a popular automatic speech recognition toolkit. We describe experiments based on training a recurrent neural network with 4 layers of 800 LSTM hidden states on a 100-hour corpora of annotated Polish speech data. We propose a MPI-based modification of the training program which minimizes the...
-
DETECTION OF BREATHING AND HEART RATE USING AN ECG SIGNAL MEASURED WHILE BATHING IN THE BATHTUB
PublicationNowadays a new area of interest is gaining importance - it is home biomedical examination. Intelligent home can be supported by set of devices for habitants observation. It can be particularly useful for elders or person with some health risks but living alone. One of critical locations within the house is bathroom. One of utilities in the bathroom is a bathtub which is sometimes preferred over shower. There are reports of problems...
-
Computer experiments with a parallel clonal selection algorithm for the graph coloring problem
PublicationArtificial immune systems (AIS) are algorithms that are based on the structure and mechanisms of the vertebrate immune system. Clonal selection is a process that allows lymphocytes to launch a quick response to known pathogens and to adapt to new, previously unencountered ones. This paper presents a parallel island model algorithm based on the clonal selection principles for solving the Graph Coloring Problem. The performance of...
-
Stability of roof trusses stiffened by corrugated sheets
PublicationThe present parametric study is devoted to the stability analysis of a set of trusses stiffened by decking of corrugated steel sheets. For different parameters of corrugated sheets the critical loading of the roof is calculated. In the parametrical analysis the threshold bracing condition of the roof is obtained. Then the geometrically non-linear analysis of trusses braced by corrugated sheets was conducted. As a results of non-linear...
-
Enhanced switched parasitic antenna with switched active monopoles for indoor positioning systems
PublicationThis paper presents the concept of enhanced reduced-size steerable antenna array with two rows of switched active and passive elements. Designed array is similar to ESPAR antenna but it has a set of switched monopoles instead of central one. It is intended for 2.4 GHz ISM applications with emphasis on indoor positioning systems (IPS). Proposed antenna provides improved radiation parameters and reduced dimensions in comparison to...
-
Data Mining Applications and Methods in Medicine
PublicationIn this paper we describe the research area of data mining and its applications in medicine. The origins of data mining and its crucial features are shortly presented. We discuss the specificity of medicine as an application area for computer systems. Characteristic features of the medical data are investigated. Common problems in the area are also presented as well as the strengths and capabilities of the data mining methods....
-
MEASUREMENT O F HEALTHCARE SYSTEM EFFICIENCY IN OECD COUNTRIES
PublicationIncreased spending on healthcare systems in many countries tends to attract attention to their efficiency. The aim of this paper is to evaluate the efficiency of healthcare systems in the OECD countries and indicate causes of inefficiency by applying Data Envelopment Analysis (DEA) and using additive and super-efficiency models. The homogeneity of the sample is assessed and outliers are excluded. A ranking is established on the...
-
New Approach to Arc Fitting for Railway Track Realignment
PublicationThis article presents a new method of arc fitting for railway track realignment. The theoretical foundations are presented, along with a detailed algorithm of the iterative computational process. This method is based on solving a set of linearized pseudo-observation equations. The formulas of the functional model of the fitting problem were derived, and a special form of objective function is proposed. An iterative method for optimization...
-
Uncertainty analysis of measuring system for instantaneous power research
PublicationThe paper presents a metrological analysis of the measurement system used for diagnosis of induction motor bearings, based on the analysis of the instantaneous power. This system was implemented as a set of devices with dedicated software installed on a PC. A number of measurements for uncertainty estimation was carried out. The results of the measurements are presented in the paper. The results of the aforementioned analysis helped...
-
Detection of impulsive disturbances in archive audio signals
PublicationIn this paper the problem of detection of impulsive disturbances in archive audio signals is considered. It is shown that semi-causal/noncausal solutions based on joint evaluation of signal prediction errors and leave-one-out signal interpolation errors, allow one to noticeably improve detection results compared to the prediction-only based solutions. The proposed approaches are evaluated on a set of clean audio signals contaminated...
-
Simple Fractal Calculus from Fractal Arithmetic
PublicationNon-Newtonian calculus that starts with elementary non-Diophantine arithmetic operations of a Burgin type is applicable to all fractals whose cardinality is continuum. The resulting definitions of derivatives and integrals are simpler from what one finds in the more traditional literature of the subject, and they often work in the cases where the standard methods fail. As an illustration, we perform a Fourier transform of a real-valued...
-
Design of modified PID controllers for 3D crane control
PublicationFrom the control viewpoint, 3D crane is a dynamic, nonlinear and multidimensional electromechanical system. In this paper, five control systems using a set-point weighted PID controllers (modified controllers) are designed. These structures and properties are presented. Optimization process of controllers settings based on integral performance indices is made. Simulation tests of control systems are presented. Comparison of integral...
-
Propagation in the Open Cylindrical Guide of Arbitrary Cross Section With the Use of Field Matching Method
PublicationA simple solution to propagation problem in open waveguides and dielectric fibers of arbitrary convex cross section is presented. The idea of the analysis is based on the direct field matching technique involving the usage of the field projection at the boundary on a fixed set of orthogonal basis functions. A complex root tracing algorithm is utilized to find the propagation coefficients of the investigated guides. Different convex...
-
A Triplet-Learnt Coarse-to-Fine Reranking for Vehicle Re-identification
PublicationVehicle re-identification refers to the task of matching the same query vehicle across non-overlapping cameras and diverse viewpoints. Research interest on the field emerged with intelligent transportation systems and the necessity for public security maintenance. Compared to person, vehicle re-identification is more intricate, facing the challenges of lower intra-class and higher inter-class similarities. Motivated by deep...
-
An application of simulation model of fuel consumption in diagnostic system of wheeled tractors
PublicationAn application of computer controlled fuel injection systems in vehicle engines and growing demands concerning toxic substances emission and fuel consumption was a main reason for OBD (On Board Diagnosis) development. In spite of a great technological development, only some tractors are equipped in diagnostic systems. On board diagnostic is strongly connected with emission demands and does not concern other important vehicle functions. In...
-
Electroelastic biaxial compression of nanoplates considering piezoelectric effects
PublicationIn the present theoretical work, it is assumed that a piezoelectric nanoplate is connected to the voltage meter which voltages have resulted from deformation of the plate due to in-plane compressive forces whether they are critical buckling loads or arbitrary forces. In order to derive governing equations, a simplified four-variable shear deformation plate theory has been employed using Hamilton’s principle and Von-Kármán...
-
On the Hat Problem on the Cycle C7
PublicationThe topic is the hat problem in which each of n players is randomly fitted with a blue or red hat. Then everybody can try to guess simultaneously his own hat color by looking at the hat colors of the other players. The team wins if at least one player guesses his hat color correctly, and no one guesses his hat color wrong; otherwise the team loses. The aim is to maximize the probability of a win. In this version every player can...
-
Steady-State Vibration Level Measurement of the Five-Phase Induction Machine during Third Harmonic Injection or Open-Phase Faults
PublicationMultiphase electric machines are increasingly used in various industries and for electromobility. Complex systems have been developed for the control and powering of multiphase machines, which require verification. The quality of control and the power supply of electric machines is usually evaluated by analyzing various electrical parameters. On the other hand, taking into account the fact that a motor is an electrical-mechanical...
-
Preparation and Characterization of Nanomaterial Consisting of Silica Aerogel & Carbon Tested as an Electrode in Non-Aqueous Media Containing Lithium Salt.
PublicationSilica aerogel (SiO2ag) was combined with carbonaceous material in the pyrolysis process of hydrocarbons. The obtained nanocomposite SiO2ag/C was amorphous, partially preserving the porous structure of SiO2ag. The specific surface area changes from 445.6 m2/g for pure SiO2ag to 205.52 m2/g SiO2ag/C. The 29Si MAS-NMR shows a three-dimensional matrix with silicon atoms connected to other silicon atoms by four...
-
Some aspects of noise generated by a small ship in the shallow sea
PublicationThe passing and underwater moving objects produce the noises of variable intensity, which significantly increase the overall level of noise in the sea. This applies to both the sonic and ultrasonic range. The excessive levels of underwater noise adversely affects the so-called underwater acoustic climate and is the reason why this phenomenon is intensively investigated from the number of years. The results of experimental work...
-
Fuctional structure of diagnostic system for wheeled tractors
PublicationAn application of computer controlled fuel injection systems in vehicle engines and growing demands concerning toxic substances emission and fuel consumption was a main reason for OBD (On Board Diagnosis) development. In spite of a great technological development, only some tractors are equipped in diagnostic systems. On board diagnosis is strongly connected with emission demands and does not concern other important vehicle functions.In...
-
Justification of quasi-stationary approximation in models of gene expression of a self-regulating protein
PublicationWe analyse a model of Hes1 gene transcription and protein synthesis with a negative feedback loop. The effect of multiple binding sites in the Hes1 promoter as well as the dimer formation process are taken into account. We consider three, possibly different, time scales connected with: (i) the process of binding to/dissolving from a binding site, (ii) formation and dissociation of dimers, (iii) production and degradation of Hes1...
-
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublicationCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...
-
Light Symposium. Connecting health research with lighting practice
PublicationThanks to state-of-the-art medical and environmental research, our current understanding about the impact of light and lighting is improving at a rapid rate. While the evolution of lighting technologies offers promising design possibilities, it also poses new challenges to planners and the general public. This is further complicated by the fact that today’s modern indoor lifestyle means we can be completely disconnected from nature...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublicationGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Fast High-Impedance Spectroscopy Method Using SINC Signal Excitation
PublicationIn this paper the method of fast impedance spectroscopy of technical objects with high impedance (|Zx| > 1 Gohm) is evaluated by means of simulation and practical experiment. The method is based on excitation of an object with a sinc signal and sampling response signals proportional to current flowing through and voltage across the measured impedance. The object impedance spectrum is obtained with use of continuous Fourier transform...
-
Validation of atmospheric aerosols parallel sampling in a multifold device
PublicationIn this work, particulate matter was collected using an active sampling system consisting of a PM10 (<10 μm) inlet coupled to a multifold device containing six channels, connected to a vacuum pump. Each channel was equipped with a filter holder fitted with adequately chosen filters. The system was fixed on a metallic structure, which was placed on the roof of the laboratory building, at the Faculty of Sciences, in Lisbon. Sampling...
-
Enhancement of the Magnetoresistance in the Mobility‐Engineered Compensated Metal Pt 5 P 2
PublicationThe magnetoresistance (MR) in nonmagnetic materials continues to be a fertile research area in materials science. The search for giant, positive MR has been limited to a rather small window of materials such as high-mobility semimetals in single-crystalline form. Here, the observation of a very large positive MR in metallic Pt5P2 in polycrystalline form is reported. The observations reveal that improvement of the crystallinity...
-
Adaptive Optimal Discrete-Time Output-Feedback Using an Internal Model Principle and Adaptive Dynamic Programming
PublicationIn order to address the output feedback issue for linear discrete-time systems, this work suggests a brand-new adaptive dynamic programming (ADP) technique based on the internal model principle (IMP). The proposed method, termed as IMP-ADP, does not require complete state feedback, merely the measurement of input and output data. More specifically, based on the IMP, the output control problem can first be converted into a stabilization...
-
Searching by Heterogeneous Agents
PublicationIn this work we introduce and study a pursuit-evasion game in which the search is performed by heterogeneous entities. We incorporate heterogeneity into the classical edge search problem by considering edge-labeled graphs. In such setting a searcher, once a search strategy initially decides on the label of the searcher, can be present on an edge only if the label of the searcher and the label of the edge are the same. We prove...
-
Influence of Natural Conditions on the Imaging of the Bottom of the Gdańsk Bay by Means of the Side Scan Sonar
PublicationThe interest in underwater resources is the reason for the development of modern hydroacoustic systems, including side sonars, which find numerous applications such as: research of seabed morphology and sediment characteristics, preparation of sea sediment maps, and even in special cases of biocenoses such as sea grass meadows, detection of specific targets at the bottom such as shipwrecks, mines, identification of suitable sites...
-
Mobile virtual presence in civil engineering education and training
PublicationEducation technologies are on the cusp, emerging technologies connected with each other might reveal new added value in this field. In this paper, the author showed a framework for conducting civil engineering classes with a virtual presence on the construction site. The presented idea might be realized by use of the unnamed aerial vehicle equipped with 360 video camera. On-site activities are transmitted at a distance by GSM and...
-
A Reduction Method for Bathymetric Datasets that Preserves True Coastal Water Geodata
PublicationWater areas occupy over 70 percent of the Earth’s surface and are constantly subject to research and analysis. Often, hydrographic remote sensors are used for such research, which allow for the collection of information on the shape of the water area bottom and the objects located on it. Information about the quality and reliability of the depth data is important, especially during coastal modelling. In-shore areas are liable...