displaying 1000 best results Help
Search results for: UNIAXIAL COMPRESSIVE STRENGTH
-
Bearing capacity of working platform using distinct layout optimization method
PublicationBearing capacity of the working platforms from sandy soil resting on NC and OC clays was analyzed using LimitState GEO program. Different failure modes are considered using distinct layout optimization (DLO) method, which forms the upper bound solution of limit state analysis. Different mechanisms of failure were observed as a function of the platform thickness, angle of internal friction of the platform material and undrained...
-
Study of the Resistance to Influence of Aggressive Liquids on Concrete with Lightweight Aggregate
PublicationThe corrosion of the structure of concrete caused by the aggressive external environment is one of the main problems that can reduce the durability of buildings. The paper analyzes the influence of the type of component on selected properties of lightweight concrete (LWC) exposed to aggressive liquids. When lightweight concrete containing porous aggregates is used, the influence of an aggressive environment may be of particular...
-
Structural, thermal and physico-mechanical properties of polyurethane/brewers’ spent grain composite foams modified with ground tire rubber
PublicationIn this work, brewers’ spent grain (BSG) and ground tire rubber (GTR) waste fillers were applied as low-cost reinforcement phase in rigid polyurethane foam (PUR). PUR/BSG/GTR composites were prepared by a single step method, using polyglycerol as partial substitute of commercially available petrochemical polyols. Foaming parameters, chemical structure, dynamic mechanical properties, thermal stability, physico-mechanical properties...
-
Experimental Study of the Resistance to Influence of Aggressive Liquids on Lightweight Concrete
PublicationIn light of the scientific research, the corrosion of concrete structures is one of the main problems that may reduce their durability due to the negative impact of the natural environment. The paper analyzes the influence of the type of component on the selected properties of lightweight concrete subjected to the influence of aggressive liquids. Four concrete mixes were prepared with a granular aggregate made of foamed glass (GEGA)...
-
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublicationThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublicationThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
Wytrzymałość pętli wplatanych na linach podwójnie plecionych
PublicationCechą wyróżniającą statki żaglowe z grona innych obiektów pływających są żagle. To cecha widoczna, za którą kryją się mniej romantyczne elementy, takie jak maszty, liny i osprzęt. Rozpostarcie białych płócien na maszcie i następnie żeglowanie wymaga sprawnego operowania nimi, co wiąże się z doborem odpowiedniego ich zestawu, ułożenia i napięcia. To maszty są kręgosłupem takielunku, a liny jego mięśniami i ścięgnami. Do poprawnego...
-
Dynamic fracture of brittle shells in a space-time adaptive isogeometric phase field framework
PublicationPhase field models for fracture prediction gained popularity as the formulation does not require the specification of ad-hoc criteria and no discontinuities are inserted in the body. This work focuses on dynamic crack evolution of brittle shell structures considering large deformations. The energy contributions from in-plane and out-of-plane deformations are separately split into tensile and compressive components and the resulting...
-
Experimental study on the effect of selected sterilization methods on mechanical properties of polylactide FFF specimens
PublicationPurpose: Biodegradable polymers are widely used in personalized medical devices or scaffolds for tissue engineering. The manufacturing process should be finished with sterilization procedure. However, it is not clear how the different sterilization methods have an impact on the mechanical strength of the three-dimensional (3D)-printed parts, such as bone models or personalized mechanical devices. This paper aims to present the...
-
Experimental and Numerical Investigation of Tensile and Flexural Behavior of Nanoclay Wood-Plastic Composite
PublicationIn this study, the effect of wood powder and nanoclay particle content on composites’ mechanical behavior made with polyethylene matrix has been investigated. The wood flour as a reinforcer made of wood powder was at levels of 30, 40, and 50 wt.%, and additional reinforcement with nanoclay at 0, 1, 3, and 5 wt.%. Furthermore, to make a composite matrix, high-density polyethylene was used at levels of 70, 60, and 50% by weight....
-
Buckling analyses of metal cylindrical silos containing bulk solids during filling
PublicationThe paper presents 3D results on stability of thin-walled cylindrical metal silos made of isotropic rolled and corrugated plates containing bulk solids. The behavior of bulk solids was described using a hypoplastic constitutive model. Nonlinear finite element (FE) analyses with both geometric and material nonlinearity were performed with a perfect and an imperfect silo shell wherein initial geometric imperfections were taken into...
-
Analytical approach for membrane action in laterally-restrained reinforced concrete square slabs under uniformly distributed loads
PublicationLaterally-restrained reinforced concrete slabs can mobilise compressive membrane action and subsequent tensile membrane action under extreme loading conditions, thereby enhancing the load resistance under uniformly distributed loads. Previous analytical study focuses primarily on tensile membrane action in simply-supported slabs. This paper describes an analytical approach for membrane action in laterally-restrained square slabs....
-
Mechanical Properties of 3D Printed Parts and Their Injection Molded Alternatives Subjected to Environmental Aging
PublicationAdditive manufacturing is the technology used in medical, industrial, or lifestyle applications. The scientific literature include works reporting various manufacturing parameters’ influence on changes in additive manufacturing components’ mechanical behavior, especially with fused filament fabrication (FFF). The changes in mechanical strength and toughness of FFF compared to injection molding parts were studied. In the study,...
-
Stress analysis of a strip under tension with a circular hole
PublicationThe paper addresses stress analysis of a strip with a circular hole under uniform uniaxial tension based oncircumferential stress expressionρπ. Stresses are analyzed in the infinite-length strips under tension with holes, the ratioof the hole radiusa to the strip half-widthb is either equal to:κ =a/b = 0.1 orκ = 0.5. Circumferential stresses aredetermined in selected cross-sections of the strip. The stress diagrams display local...
-
Właściwości mechaniczne tworzywa PET - przegląd literatury
PublicationThe article describes the influance of the microstructure and environment conditions on the mechanical properties of PET material. From the microskopic point of view, mechanical and thermal properties of PET material have the biggest influance on orientation and crystallization processes of material. From the macroskopic point of view mechanical properties can be described by parameters derived from strees-strain mechanical answers...
-
A brief note on monotonic and fatigue fracture events investigation of thin-walled tubular austenitic steel specimens via fracture surface topography analysis (FRASTA)
PublicationThe main objective of this short communication is to show the fracture progression in each loading case and complement knowledge about fracture mechanisms underpinning the tensile and fatigue performance of thin-walled tubes. For this purpose, the fracture surface topography analysis (FRASTA) method was used in the thin-walled tubular austenitic stainless-steel specimens. Two cases were analyzed: monotonic tension, and uniaxial...
-
Reliability model of slide bearings with particular attention given to lubricating oil
PublicationThe paper presents the slide bearing with circulating lubrication as a system of series three-element structure, where lubricating oil is the weakest link. In accordance with the Pierce statement that ''strength of chain is the strength of its weakest link'', a bearing reliability model has been developed. It allows to use the lubricating oil to evaluate the probability of correct working of the whole slide bearing, i.e. the reliability....
-
Measurement of Seafloor Acoustic Backscatter Angular Dependence at 150 kHz Using a Multibeam Echosounder
PublicationAcoustic seafloor measurements with multibeam echosounders (MBESs) are currently often used for submarine habitat mapping, but the MBESs are usually not acoustically calibrated for backscattering strength (BBS) and cannot be used to infer absolute seafloor angular dependence. We present a study outlining the calibration and showing absolute backscattering strength values measured at a frequency of 150 kHz at around 10–20 m water...
-
Tensile curve of E grade steel for shipbuilding
Open Research DataIn the shipbuilding industry, the risk of brittle fractures developing in constructions is limited by employing certified materials of specific impact strength, determined using the Charpy method (for a given design temperature) and by exercising control over the welding processes (technology qualification, supervision of production, tests of non-destructive...
-
Effect of bio-polyol molecular weight on the structure and properties of polyurethane-polyisocyanurate (PUR-PIR) foams
PublicationThe increasing interest in polyurethane materials has raised the question of the environmental impact of these materials. For this reason, the scientists aim to find an extremely difficult balance between new material technologies and sustainable development. This work attempts to validate the possibility of replacing petrochemical polyols with previously synthesized bio-polyols and their impact on the structure and properties...
-
The effect of preliminary creep-strain on material behavior under LCF tension/compression and pure torsion regimes
PublicationThis paper presents the results of experimental tests of monotonic tension and torsion, creep-rupture and preliminary creep at 200C and 300C, as well as low-cycle fatigue of 2024 T3511 aluminum alloy. The fatigue process was conducted at room temperature for uniaxial tension/compression and torsion. The as-received material and pre-deformed material were also investigated during creep at elevated temperature. Basic monotonic,...
-
Mechanical and physical assessment of epoxy, mineral, solvent-based, and water-soluble coating materials
PublicationThis paper assesses the behavior of mineral, epoxy (EP), solvent, and water-soluble coatings when exposed to salt and regular water for 28 days. Also, it evaluates the pull-off adhesion strength of the same coating materials applied to concrete slabs saturated with oil and water and dried with two different processes: air-dried for 28 days and air-dried for 14 days plus 14 days in the oven at 70 °C. Properties such as carbonation,...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublicationThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
Experiments and calibration of a bond-slip relation and efficiency factors for textile reinforcement in concrete
PublicationTextile reinforcement yarns consist of many filaments, which can slip relative each other. At modelling of the global structural behaviour, interfilament slip in the yarns, and slip between the yarns and the concrete can be considered by efficiency factors for the stiffness and strength of the yarns, and by applying a bond-slip relation between yarns and concrete. In this work, an effective and robust method for calibration of...
-
Some problems of slide bearing material fatigue evaluation.
PublicationA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Effect of slightly crosslinked butyl rubber and compatibilizer additives on properties of recycled polyethylene-ground tire rubber blends
PublicationSlightly crosslinked butyl rubber, (PhMe2CO)(2) and maleic anhydride were added as compatibilizer to the recycled polyethylene-ground tire rubber blends. Recycled postprodn. and postconsumer (shredded bottle caps) polyethylene wastes were used. The thermoplastic compns. were studied for statistic and dynamic mech. properties and morphol. The addn. of butyl rubber resulted in a decrease of the tensile strength and hardness of the...
-
Badania wytrzymałościowe zgrzein łączących pręty zbrojeniowe o średnicy Ø30mm
PublicationZakres badań dotyczy oceny wytrzymałościowej zgrzein doczołowych, wykonanych metodą zwarciową. Elementami zgrzewanymi były pręty zbrojeniowe o średnicy Ø30mm. Badania związane są z okresową kontrolą stabilności parametrów zgrzewarki, szczególnie w odniesieniu do górnych, dopuszczalnych przez producenta zakresów parametrów zgrzewania oraz analizą wyników i porównaniu rezultatów prób wytrzymałościowych uzyskanych w 2019 i 2020 w...
-
Processing of point cloud data retrieved from terrestrial laser scanning for structural modeling by Finite Element Method
PublicationFinite Element Method is one most popular contemporary method of strength analysis. The method is an advanced method for solving differential equations, based on discretization, which means that area is divided into finite elements. Each finite element has a solution of the equation approximated by specific functions and performing the actual calculations only for nodes of this division. Finite Element Method is widely used in...
-
Application of two-dimensional intensity maps in high-accuracy polarimetry
PublicationWe propose the analysis of 2D intensity contour maps which is based on the optical transmission function for the polarizer-specimen-analyzer system. A small modification of the high-accuracy universal polarimeter (HAUP) technique was used to measure the intensity maps (HAUP maps) and determine the phase retardation, linear dichroism (LD) parameters, and multiple light reflection contribution in uniaxial crystals. We have performed...
-
Spectral measurement of birefringence using particle swarm optimization analysis
PublicationThe measurement of birefringence is useful for the examination of both technical and biological objects. One of the main problems is that the polarization state of light in birefringent media changes periodically. Without the knowledge of the period number, the birefringence of a given medium cannot be determined reliably. We propose to analyse the spectrum of light in order to determine the birefringence. We use a Particle Swarm...
-
Parameters’ Identification of Perzyna and Chaboche Viscoplastic Models for Aluminum Alloy at Temperature of 120◦C
PublicationThe main purpose of this paper is the parameters identification of the Perzyna and the Chaboche models for the aluminum alloy at elevated temperature. The additional purpose is comparison of the results for these viscoplastic models. The results have been verified by the numerical simulation of the laboratory tests. The material parameters have been calculated on the basis of the uniaxial tension test. The determination of the...
-
Optimization of biocorrosion resistance and mechanical properties of PM Ti–XAl–2Fe–3Cu alloys by response surface methodology
PublicationIn the current study, the biocorrosion resistance and mechanical properties of the Ti–XAl–2Fe–3Cu (wt%) (X = 6, 4, 2 wt%) alloy produced by powder compact extrusion of blended elemental powders were optimized by using the response surface methodology in order to gain the best combination of processing parameters. To run the optimization process, central composite design with three equal levels of oxygen, hydrogen and aluminum was...
-
The Influence of Articular Cartilage Thickness Reduction on Meniscus Biomechanics
PublicationObjective Evaluation of the biomechanical interaction between meniscus and cartilage in medial compartment knee osteoarthritis. Methods The finite element method was used to simulate knee joint contact mechanics. Three knee models were created on the basis of knee geometry from the Open Knee project. We reduced the thickness of medial cartilages in the intact knee model by approximately 50% to obtain a medial knee osteoarthritis...
-
Eksperymentalna weryfikacja procedury szacowania wytrzymałości młodego betonu wg normy ASTM C1074
PublicationW referacie przedstawiono metodę służącą oszacowaniu wytrzymałości betonu w trakcie procesu dojrzewania (ang. Maturity Method) bazującą na procedurze określonej zgodnie z amerykańską normą, która uwzględnia wpływ połączonych efektów temperatury i czasu na rozwój wytrzymałości betonu. Standardy ASTM C1074 zostały opracowane przez NBS (ang. National Bureau of Standards) z uwagi na powtarzające się wypadki na palcu budowy wynikające...
-
Buckling analyses of cylindrical metal silos containing bulk solids
PublicationThe paper presents quasi-static 3D buckling analysis results of thin-walled cylindrical metal silos with and without bulk solids. The behaviour of the bulk solid was described with a hypoplastic constitutive model. Non-linear analyses with geometric and material non-linearity were performed with a perfect and an imperfect silo shell. Different initial geometric imperfections were considered. The influence of internally stored bulk...
-
Parametry mechaniczne platformy roboczej na podstawie badań DMT
PublicationNośność platformy roboczej określana jest w sposób analogiczny do nośności podłoża uwarstwionego, w którym warstwa wierzchnia zbudowana z gruntu niespoistego spoczywa na słabonośnym podłożu z gruntu spoistego. Badanie DMT wykorzystano do wyznaczenia parametrów wytrzymałościowych podłoża (kąta tarcia wewnętrznego warstwy górnej i wytrzymałości na ścinanie bez odpływu podłoża słabonośnego) oraz do wyznaczenia modułu odkształcenia...
-
Mechanical response of human thoracic spine ligaments under quasi-static loading: An experimental study
PublicationPurpose This study aimed to investigate the geometrical and mechanical properties of human thoracic spine ligaments subjected to uniaxial quasi-static tensile test. Methods Four human thoracic spines, obtained through a body donation program, were utilized for the study. The anterior longitudinal ligament (ALL), posterior longitudinal ligament (PLL), capsular ligament (CL), ligamenta flava (LF), and the interspinous ligament and...
-
SUBSOIL CHARACTERISTICS OF THE VISTULA RIVER DIKES
PublicationThe results of CPTU tests are used to determine the strength parameters of a dike subsoil. Stress state and stress history of the subsoil under the flood embankment was evaluated with CPTU and DMT tests. Normally consolidated soil was found under the central part of the dike, while the subsoil near the dike toe is found to be overconsolidated. Due to consolidation the undrained shear strength of the subsoil under the central part...
-
Bearing capacity of the working platform with kinematic method
PublicationBearing capacity of the working platform for heavy tracks was analysed using Distinct Layout Optimization (DLO) method. The platform layer constructed from cohesionless soils is resting on weak cohesive subgrade. Different thickness of the platform, its effective angle of internal friction and undrained shear strength of the soft soil were taken into consideration. Kinematic method permits different failure mechanisms to be analyzed....
-
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublicationThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
Wyznaczanie wytrzymałości betonu na podstawie funkcji dojrzałości wg amerykańskiej normy ASTM C1074-11
PublicationArtykuł poświęcono wyznaczaniu wytrzymałości betonu na podstawie funkcji dojrzałości wg normy ASTM C1074-11 (ang. Maturity Method). Metoda bazuje na rejestracji zmian tem - peratury w trakcie hydratacji dojrzewającego betonu. Wartykule zaprezentowano procedurę badawczą służącą wyznaczeniu funk - cji dojrzałości dla wybranej mieszanki betonowej oraz zależności wytrzymałość-dojrzałość. Celem badań jest wyznaczanie zmian w czasie...
-
Meso‐scale analyses of size effect in brittle materials using DEM
PublicationThe paper describes numerical meso-scale results of a size effect on strength, brittleness and fracture in brittle materials like concrete. The discrete element method (DEM) was used to simulate the size effect during quasi-static splitting tension with the experimental-based meso-structure. The two-dimensional (2D) calculations were carried out on concrete cylindrical specimens with two diameters wherein two different failure...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublicationGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Pressure-induced flow processing behind the superior mechanical properties and heat-resistance performance of poly(butylene succinate)
PublicationWe propose a pressure-induced flow (PIF) processing method for the simultaneous enhancement of strength, toughness, and heat resistance of biodegradable poly(butylene succinate) (PBS). The pressure and temperature were systematically adjusted to optimize the tensile strength of PBS. Under the optimized processing conditions, the structured PBS was characterized by relatively high strength of 89.5 MPa, toughness of 21.4 kJ·m−2 ,...
-
Temper bead welding of S420G2+M steel in water environment
PublicationThe article presents the idea of the use of Temper Bead Welding (TBW) technique to improve the weldability of high strength steel at underwater wet welding conditions. Wet welding method with the use of covered electrodes is described. This work shows results of metallographic examinations and hardness measurements of samples of S420G2+M steel with weld beads performed under water. It has been shown that Temper Bead Welding technique...
-
Selected Problems of Machine Dynamics II
e-Learning CoursesThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics
e-Learning CoursesThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics - advances
e-Learning CoursesThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics - advances
e-Learning CoursesThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Strenght of materials towards applications, PG_00053661
e-Learning CoursesThe aim of the course is to perform the following subjects: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES