displaying 1000 best results Help
Search results for: BITUMEN EMULSION, EMULSIFIER, SLURRY SURFACING MIXES, THIN-LAYER COATING, MODIFIED BITUMEN, ADHESION, PHENOL-CRESOL-FORMALDEHYDE RESIN.
-
Application of thin diamond films in low-coherence fiber-optic Fabry Pérot displacement sensor
PublicationThe novel fiber-optic low coherence sensor with thin diamond films is demonstrated. The undoped and boron-doped diamond films were elaborated by the use of the microwave plasma enhanced chemical vapor deposition (μPE CVD) system. The optical signal from the Fabry–Pérot cavity made with the application of those thin films is sensitive to displacement. The sensor characterization was made in the range of 0–600 μm. The measurements...
-
Rubrene Thin Films with Viably Enhanced Charge Transport Fabricated by Cryo-Matrix-Assisted Laser Evaporation
PublicationAmong organic semiconductors, rubrene (RB; C42H28) is of rapidly growing interest for the development of organic and hybrid electronics due to exceptionally long spin diffusion length and carrier mobility up to 20 cm2V−1s−1 in single crystals. However, the fabrication of RB thin films resembling properties of the bulk remains challenging, mainly because of the RB molecule’s twisted conformation. This hinders the formation of orthorhombic...
-
Rigid polyurethane foams modified with selected layered silicate nanofillers
PublicationThe aim of this study was to investigate the effect of three different nanofillers on the properties of rigid polyurethane foams, which were prepared by a one-step, laboratory-scale method from a two-component system at the ratio of NCO groups to OH groups equaled to 2. The reaction mixture consisted of the proper amounts of the commercial oligoether polyol, catalysts, water, nanoclays, and polymeric diphenylmethane diisocyanate....
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublicationThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
Influence of plasmon resonance on the luminescence of titanium dioxide thin films doped with rare earth ions
PublicationIn this work the study of the optical properties of europium doped titanium dioxide thin films (TiO2:Eu) enhanced by gold plasmonic nanostructures are presented. Plasmonic platforms were manufactured by thermal annealing of thin film of Au, deposited on a Corning glass substrate. As a result of thermal treatment, gold spherical nanostructures with average dimensions of 50 nm were obtained. Luminescent TiO2:Eu film was deposited...
-
Thermoplastic polyurethane/(organically modified montmorillonite) nanocomposites produced by in situ polymerization
PublicationA series of polyurethane nanocomposites were synthesized from thermoplastic polyurethanes (with different hard segment ratios) and two types of organically modified montmorillonites (OMMT) - Cloisite® 10A and Cloisite® 20A. The thermal behavior was examined by non-isothermal thermogravimetry (TG, DTG), Differential Scanning Calorimetry (DSC) and Dynamic-Mechanical Thermal Analysis (DMTA). The results of X-ray analyses showed that...
-
Accelerated ageing of organic coating systems by thermal treatment
Publication -
Special Issue “Corrosion Resistance of Alloy and Coating Materials”
Publication -
Bio-based semi-aromatic polyesters for coating applications
PublicationLinear and branched bio-based semi-aromatic (co)polyesters were evaluated as resins for solvent-basedand powder coatings. Dimethyl-2,5-furandicarboxylate (DMF), 2,3-butanediol and various multifunc-tional comonomers were used to synthesize amorphous hydroxyl-end-capped (co)polyesters. The resinswere cross-linked using the -caprolactam blocked trimer of isophorone diisocyanate. Both the solvent-based and powder coatings proved to...
-
THE PROPERTIES OF NANOSILVER – DOPED NANOHYDROXYAPATITE COATING ON THE Ti13Zr13Nb ALLOY
PublicationThe aim of this research was to study the properties of nanohydroxyapatite (nanoHAp) and nanohydroxyapatite, doped with nanosilver (nanoHAp/nanoAg), coatings obtained by an electrophoretic deposition process. The suspensions was prepared by dispersing 0.1 g of HAp nanopowder for nanoHAp coatings and 0.1 g of nanoHAp and 0.025 g nanoAg for nanoHAp/nanoAg coatings. The deposition was carried out for 1 min at 50 V voltage followed...
-
Development of Sulfamoylated 4‑(1-Phenyl‑1H‑1,2,3-triazol-4-yl)phenol Derivatives as Potent Steroid Sulfatase Inhibitors for Efficient Treatment of Breast Cancer
PublicationWe present here the advances achieved in the development of new sulfamoylated 4-(1-phenyl-1H-1,2,3-triazol-4-yl)phenol derivatives as potent steroid sulfatase (STS) inhibitors for the treatment of breast cancer. Prompted by promising biological results and in silico analysis, the initial series of similar compounds were extended, appending a variety of m-substituents at the outer phenyl ring. The inhibition profiles of the newly...
-
Thin LSFO films for bolometers
PublicationPrzedstawiono metodę produkcji oraz temperaturowe zależności rezystancji cienkich warstw niestechiometrycznych tlenków (La,Sr)FeO3 (LSFO) przeznaczonych do zastosowań na detektory podczerwieni
-
Optimal Multivariable Control for Modified Z-source Based IPT
PublicationThis paper describes Z-source based inductive power transfer topologies control approaches. The goal of this work is a multi-variable control approach which involves a constant voltage/constant current control along with an optimal frequency control to obtain maximum efficiency. This control is applied to the wireless power transfer system based on a modified Z-source topology. The description of the control method along with simulation...
-
Functional properties of packaging materials from chemical modified stach.
PublicationThis work is focused on study of the mechanical and barrier properties of films obtained from potato starch modified with sodium tetrahydroxozincate generated in situ. The results show that the chemical modification of starch improved the water vapor permeability by about 25%, unfortunately decreased the elongation at break by 60%, when compared with unmodified starch films. However, placitization of films with glycerol at a concentration...
-
The AFM micrographs of vanadium oxides thin films obtained at 800°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on a silicon substrate and vanadium thin films were obtained by annealing as-prepared films at...
-
New Procedures for Control of Industrial Effluents Treatment Processes
PublicationThis work presents the procedures for monitoring volatile organic compounds during treatment of industrial effluents. The investigation was carried out for a specific effluent—caustic effluent from bitumen production. The developed procedures enable more detailed control of the effectiveness of wastewater treatment than standard procedures. Caustic effluents from bitumen production have a complex physicochemical form and consist...
-
Noble metal modified TiO2 microspheres: Surface properties and photocatalytic activity under UV-vis and visible light
PublicationComposite photocatalysts that consist of TiO2and noble metal nanostructures have been considered tobe the promising and pivotal material for accessible enhancement of the efficiency in the photocatalyticprocess carried out in the aqueous and gas phases. In this work we fabricated porous TiO2microspheresthrough a hydrothermal process followed by photochemical reduction of noble metal nanoparticles atthe TiO2surface. The morphology...
-
Numerical analysis of influence of intermediate stiffeners setting on the stability behaviour of thin-walled steel tank shell
Publication -
Simulation of unsteady flow over floodplain using the diffusive wave equation and the modified finite element method
PublicationWe consider solution of 2D nonlinear diffusive wave equation in a domain temporarily covered by a layer of water. A modified finite element method with triangular elements and linear shape functions is used for spatial discretization. The proposed modification refers to the procedure of spatial integration and leads to a more general algorithm involving a weighting parameter. The standard finite element method and the finite difference...
-
The AFM micrographs of vanadium oxides thin films obtained at 1200°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
The AFM micrographs of vanadium oxides thin films obtained at 400°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
The AFM micrographs of vanadium oxides thin films obtained at 600°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
The AFM micrographs of of vanadium oxides thin films obtained at 300°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
The AFM micrographs of vanadium oxide thin films obtained at 100°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
The AFM micrographs of vanadium oxides thin films obtained at 150°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
The AFM micrographs of vanadium oxides thin films obtained at 200°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
The AFM micrographs of vanadium oxides thin films obtained at 450°C
Open Research DataThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
Structural analysis of the tellurium dioxide thin films
Open Research DataTeO2 thin films were deposited by magnetron sputtering method. After deposition, amorphous samples were annealed at various temperatures. Influence of annealing temperature on a presence of crystalline phase was investigated.
-
Optical transmission of the Niobium thin films
Open Research DataNiobium thin films with a thickness of 200nm were deposited n a Corning glass substrate by magnetron sputtering method. The optical transmission spectra in a visible light range were.recorded. Investigations showed a good optical transmission thru the layers for each samples, annealed at various temperatures. For measurements samples annealed at 500,...
-
Performance of a single layer fuel cell based on a mixed proton-electron conducting composite
PublicationMany of the challenges in solid oxide fuel cell technology stem from chemical and mechanical incompatibilities between the anode, cathode and electrolyte materials. Numerous attempts have been made to identify compatible materials. Here, these challenges are circumvented by the introduction of a working single layer fuel cell, fabricated from a composite of proton conducting BaCe0.6Zr0.2Y0.2O3-δ and a mixture of semiconducting...
-
CMGNet: Context-aware middle-layer guidance network for salient object detection
PublicationSalient object detection (SOD) is a critical task in computer vision that involves accurately identifying and segmenting visually significant objects in an image. To address the challenges of gridding issues and feature...
-
Determination of Hydroxy Groups in the Modified Epoxy Oligomers Using IR-Spectroscopy
PublicationThe use of IR-spectroscopy has been proposed to determine the content of hydroxy groups in the modified functional oligomers based on bisphenol A diglycidyl ether. Apart from hydroxy groups the investigated oligomers contain epoxy or peroxy, carboxy or acrylic groups.
-
Thermal and Mechanical Properties of Microporous Polyurethanes Modified with Reduced Graphene Oxide
PublicationMicroporous polyurethanes (MPU) were modified by adding 0.25%–1.25 wt% of reduced graphene oxide (RGO). The materials were prepared without solvent via in situ polymerization. From a technological point of view, it is very important to obtain functional materials by using reacting compounds only. The thermal characteristics of obtained MPU were investigated using TGA, DSC, and DMA techniques. In comparison to nonmodified microporous...
-
Preparation of platinum modified titanium dioxide nanoparticles with the use of laser ablation in water
PublicationWe report on the preparation method of nanocrystalline titanium dioxide modified with platinum by using nanosecond laser ablation in liquid (LAL). Titania in the form of anatase crystals has been prepared in a two-stage process. Initially, irradiation by laser beam of a titanium metal plate fixed in a glass container filled with deionized water was conducted. After that, the ablation process was continued, with the use of a platinum...
-
Simultaneous elimination of Malachite Green, Rhodamine B and Cresol Red from aqueous sample with Sistan sand, optimized by Taguchi L16 and Plackett–Burman experiment design methods
Publication -
Hydrogen Embrittlement and Oxide Layer E ect in the Cathodically Charged Zircaloy-2
PublicationThe present paper is aimed at determining the less investigated effects of hydrogen uptake on the microstructure and the mechanical behavior of the oxidized Zircaloy-2 alloy. The specimens were oxidized and charged with hydrogen. The different oxidation temperatures and cathodic current densities were applied. The scanning electron microscopy, X-ray electron diffraction spectroscopy, hydrogen absorption assessment, tensile, and...
-
Effect of Temperature on n-Tetradecane Emulsion in the Presence of Phospholipid DPPC and Enzyme Lipase or Phospholipase A2
Publication -
Plant Extracts Containing Saponins Affects the Stability and Biological Activity of Hempseed Oil Emulsion System
Publication -
XRD analysis of the tellurium dioxide thin films
Open Research DataTellurium dioxide thin films were deposited by magnetron sputtering method. The XRD analysis of the films annealed at 200, 500, 650 and 700 celsius degree showed appearing of crystalline phase in a higher temeratures.
-
Enhanced boron doping of thin diamond films grown in deuterium-rich microwave plasma
PublicationThe boron-doped diamond thin films were growth in deuterium rich microwave plasma in CVD process. The mechanism of influence of plasma composition on boron doping level was studied using optical emission spectroscopy. Deuterium rich plasma results in an increased dissociation of B2H6 precursor and intense boron-radicals' production. In consequence, a higher doping level of diamond films was observed by means of Laser Induced Breakdown...
-
Torsion of restrained thin-walled bars of open constant bisymmetric cross-section
PublicationElastic and geometric stiffness matrices were derived using Castigliano's first theorem, for the case of torsion of restrained thin-walled bars of open constant bisymmetric cross-section. Functions which describe the angles of torsion were adopted from the solutions of thedifferential equation for restrained torsion. The exact solutions were simplified by expanding them in a power series. Numerical examples were taken from Kujawa...
-
Characteristics, Chemical Modification Processes as well as the Application of Silica and its Modified Forms
PublicationThe variety of chemical modifications of the surface of silica and its modified forms cause thesematerials to find a consistently wider scope of application. In the publication, the characteristicsof silica, silica gel, aerogel and xerogel are presented. The obtainment, application and propertiesof these materials are discussed. Methods of chemical modifications of surface structures withthe use of different chemical compounds...
-
Investigation of the Few‐Layer Black Phosphorus Degradation by the Photonic Measurements
PublicationFew-layer black phosphorus (FLBP) is a 2D material that gains worldwide interest for its possible applications, mainly in electronics and optoelec-tronics. However, as FLBP is prone to a degradation process under envi-ronmental conditions, there is a need for a monitoring method allowing investigation of its surface quality. Among many techniques, optoelectronic ones have unique advantages of fast response, non-contact, and non-invasive...
-
Degradation of Polycaptolactone Modified with TPS or CaCO3 in Biotic/Abiotic Sewater
PublicationThe polymer degradation process in two types of water sourced from the Baltic Sea was investigated. Polycaprolactone modified with thermoplastic starch(PCL/TPS>85%) or calcium carbonate (60% PCL/40% CaCO3)and PCL alone were incubated for 28 weeks in sea water with and without microrganisms. The experimental results indicated that in each of the experiments degradation occured. The process was more effective in sea water with microorganisms.Modification...
-
Experimental Investigation of Adhesion Failure between Waterproof Coatings and Terrace Tiles under Usage Loads
Publication -
Rod-shaped gold nanoparticles exert potent candidacidal activity and decrease the adhesion of fungal cells
Publication -
Ag/Pt-modified TiO2 nanoparticles for toluene photooxidation in the gas phase
PublicationAg/Pt-modified TiO2nanocomposites were synthesized using the sol–gel method. The effect of metal typeand amount as well as synthesis route on the photocatalytic activity in reaction of toluene removal, usedas a model volatile organic compound, was investigated. Toluene, at the concentration of about 200 ppm,was irradiated over modified TiO2using light-emitting diodes (LEDs, max= 415 nm). The results showedthat toluene could be...
-
Coplanar Waveguide-Fed Broadband Microwave Devices with (or without) a Thin Dielectric Substrate for Use in Flexible Electronic Systems
PublicationTwo examples of microwave devices, fed by a coplanar waveguide and realized on a thin substrate (or without such a substrate), are employed to investigate the influence of devices’ curvatures and the proximity of different materials on their parameters. To perform the tests, a broadband antenna and a low-pass filter are chosen. A feeding coplanar waveguide is realized on a dielectric material brick attached to an SMA connector...
-
Modified linear viscoelastic model of earthquake-induced structural pounding
PublicationIn recent times, earthquake-induced structural pounding has been intensively studied through the use of different impact force models. The numerical results obtained from the previous studies indicate that the linear viscoelastic model is relatively simple and accurate in modeling pounding-involved behavior of structures during earthquakes. The only shortcoming of the model is a negative value of the pounding force occurring just...