displaying 1000 best results Help
Search results for: SULFUR DIOXIDE EMISSION
-
The absorption and fluorescence spectra of C-1305 derivatives (IKE1-IKE8), potential antifungal agents
Open Research DataOptical measurements of C-1305 derivatives (IKE1-IKE8). The absorption spectra were recorded at 300 - 800 nm for solutions with 16 μg / mL derivative concentration. The fluorescence emission spectra were determined at 420-800 nm with the excitation wavelengths 360 or 415 nm for solutions with 1 μg / mL derivative concentration. All measurements were...
-
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublicationThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).
-
An inclination in Thermal Energy Using Nanoparticles with Casson Liquid Past an Expanding Porous Surface
PublicationPhysical aspects of inclined MHD nanofluid towards a stretching sheet embedded in a porous medium are visualized. Two types of nanoparticles are used named as copper and alumna dioxide with water as base fluid. Similarity transformations are used to convert the partial differential equations into the set of ordinary differential equation. Closed solutions are found to examine the velocity and the temperature profiles. It is examined...
-
Geotechnical Aspects of Dike Construction Using Soil-Ash Composites
PublicationAn analysis of using of anthropogenic materials, mainly ashes from Coal Combustion Products (CCP), for dike construction is shown. Perspectives of anthropogenic materials application in geotechnical engineering and their advantages in sense of the carbon dioxide reduction are discussed. According to regulations of Kioto Protocol 2005 and EU agreement “Energy Roadmap 2050” recycled materials have higher usage priority than natural...
-
Nonlinear viscoelasticity in Three Dimensional filler reinforced rubber composites and nanocomposites
PublicationThis chapter describes the influence of three-dimensional nanofillers used in elastomers on the nonlinear viscoelastic properties. In particular, this part focuses and investigates the most important three-dimensional nanoparticles, which are used to produce rubber nanocomposites. The rheological and the dynamic mechanical properties of elastomeric polymers, reinforced with spherical nanoparticles, like POSS, titanium dioxide and...
-
On Memory-Based Precise Calibration of Cost-Efficient NO2 Sensor Using Artificial Intelligence and Global Response Correction
PublicationNitrogen dioxide (NO2) is a prevalent air pollutant, particularly abundant in densely populated urban regions. Given its harmful impact on health and the environment, precise real-time monitoring of NO2 concentration is crucial, particularly for devising and executing risk mitigation strategies. However, achieving precise measurements of NO2 is challenging due to the need for expensive and cumbersome equipment. This has spurred...
-
The electrical properties mesurements of SOFC with Ce0.9Cu0.1O2-s functional layer
Open Research DataThe dataset includes the electrical properties mesurements of SOFC with Ce0.9Cu0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of SOFC with Ce0.9Co0.1O2-s functional layer
Open Research DataThe dataset includes the electrical properties mesurements of SOFC with Ce0.9Co0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of SOFC with Ce0.8Co0.1Cu0.1O2-s functional layer
Open Research DataThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Co0.1Cu0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of SOFC with Ce0.8Co0.15Cu0.05O2-s functional layer
Open Research DataThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Co0.15Cu0.05O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
Dimethyl ether (DME) as potential environmental friendly fuel
PublicationIn recent years, there has been a growing interest in replacing petroleum fuels with so-called second generation environmental friendly fuels. Compared to traditional petroleum fuels dimethyl ether (DME) could be used as a clean high-efficiency compression ignition fuel with reduced particulate matter (PM), sulfur oxides (SOx), hydrocarbons (HC), carbon monoxide (CO) as well as combustion noise. Compared to some of the other leading...
-
Preparation, characterization and anti-colitis activity of curcumin-asafoetida complex encapsulated in turmeric nanofiber
PublicationUlcerative colitis (UC) is a main form of inflammatory bowel disease (IBD). Asafoetida (ASF) and turmeric have traditionally been used for the treatment of various inflammatory diseases, including UC, because ASF is rich in sulfur compounds and turmeric contains curcumin (CUR). Turmeric nanofiber (TNF), the modified cell wall component of turmeric is considered to play important role in the human diet, health and can be used as...
-
ENERGY EFFICIENT SMALL INLAND PASSENGER SHUTTLE FERRY WITH HYBRID PROPULSION - CONCEPT DESIGN, CALCULATIONS AND MODEL TESTS
PublicationIn recent years, there has been a significant development in “green” and energy efficient propulsion systems, which fits into the general trend of environmentally friendly “green shipping”. The pursued goal is to construct a safe passenger ship that is low in energy demand and equipped with a highly energy efficient, emission-free propulsion system. The paper presents main problems encountered by designers of a small, hybrid-powered...
-
Novel analytical approach for real-time monitoring of volatile Maillard reaction products emitted from the sugar-amino acid model system using proton transfer reaction mass spectrometry
PublicationIn the presented research, volatile Maillard reaction products formation in the two sugar-amino acid model systems, namely glucoselysine and ribose-lysine model systems were investigated using proton transfer reaction mass spectrometry. Obtained data were supported by the reference method, i.e., UV/Vis spectrometry. A number of volatile organic compounds were selected based on the correlation of the effect of Maillard reaction...
-
The conception of energetic investigations of the multisymptom fatigue of the simple mechanical systems' constructional materials
PublicationThe article presents the basic assumptions of the research project aimed, as the main scientific purpose, an identification of the slow-changeable energy processes surrounding the high-cycle fatigue of constructional materials within the plain mechanical system, especially the marine one, for diagnostic purposes. There is foreseen an application of alternative diagnostic methods based on energetic observations of the multi-symptom,...
-
A novel luminescent chemical sensor for the determination of Pb 2+ and Cu 2+ ions
PublicationSilica xerogel surface grafted with aminopropyl (PrNH2) groups was additionally treated by cetyltrimethylammonium bromide (CTAB) surfactant and ascorbic acid (asc) in alkaline solution. This material symbolized as SiO2-PrNH2-CTAB/asc, proved to be a stable luminescent material, exhibited an emission band peaked at 393 nm under excitation wavelength 335 nm. Time evolution of the band intensity suggests changes of defect concentration...
-
Determination of total mercury in raw petrol using cold vapour atomic absorption spectrometry
PublicationPresence of different forms of mercury in petroleum based products may impair the proper operation of the equipment or led to poisoning of automotive catalysts. However much more important problem is environmental pollution with mercury emitted from different types of fossil fuels. Although the average mercury concentration in petroleum based products (automotive fuels) is on the level around 1 ppb, taking into account annual...
-
Luminescence recognition material as an INHIBIT logic gate in presence of Pb2+ and Cu2+ ions in aqueous solutions
PublicationA recognition material consisting of silica xerogel with amino-modified surface selectively recognizes Pb2+ and Cu2+ (but only in presence of Pb2+ ions) in aqueous solutions of other metal ions. The analytical action of the material is based on a significant change in luminescence emission spectra of the material after chemisorption of Pb2+ ions. In the presence of Pb2+ in octahedral coordination environment, a new broad and strong...
-
Investigation of Narrow Transverse and Longitudinal Electrostatic Precipitators
PublicationDiesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are not enough effective or very expensive. An electrostatic precipitation was proposed as an alternative method for control of a diesel particulate emission. Therefore, narrow electrostatic precipitators (ESPs) have become a subject of...
-
Nonconventional 1,8-Diazafluoren-9-One Aggregates for Green Light Enhancement in Hybrid Biocompatible Media
PublicationOrganic aggregates currently play a prominent role, mainly for their unique optoelectronic properties in the aggregated state. Such properties can be related to the aggregates’ structure and the molecular packing mode. In the literature, we have well-established models of H and J aggregates defined based on the molecular exciton model. However, unconventional aggregates, the most unrecognized forms, have been generating interest...
-
An algorithm for selecting a machine learning method for predicting nitrous oxide emissions in municipal wastewater treatment plants
PublicationThis study presents an advanced algorithm for selecting machine learning (ML) models for nitrous oxide (N2O) emission prediction in wastewater treatment plants (WWTPs) employing the activated sludge process. The examined ML models comprised multivariate adaptive regression spline (MARS), support vector machines (SVM), and extreme gradient boosting (XGboost). The study explores the concept that involves new criteria to select the...
-
Structure and optical parameters of Eu doped tellurium oxide thin films prepared by reactive magnetron sputtering method
PublicationIn this work the structural properties and photoluminescence of tellurium dioxide thin films doped by europium were described. Thin films were deposited by magnetron sputtering method and simultaneously heated at 200 °C. Presence of Eu ions and their valence states was confirmed by X-ray photoemission spectroscopy measurements. The structure of the films as well as the influence of europium dopant on crystalline structure of the...
-
Identification of volatile compounds based on the electrocatalytic gas sensor responses
PublicationMeasured response in case of electrocatalytic gas sensors is in form of a voltamperometric characteristic. Current-voltage (I-V) response shape depends on the gas type and its concentration. Such response contains significantly more information comparing with typical electrochemical sensors, but is quite difficult to analyze. When I-V curve contains current peaks, position of such peaks can be used...
-
Polyurethane-based aerogels: Preparation, properties, and applications
PublicationPolyurethane aerogels (PUAs) are interesting materials because of their high porosity, low density, and low thermal conductivity, which result in their application as thermal insulations. PUAs are mainly synthesized using di- and polyisocyanates, diols or polyols, catalysts (tertiary amines and organometallic), and solvents (which are used as reaction medium, purifying of obtained semiproducts). Preparation procedure involves several...
-
"Numeryczna symulacja pracy gazowego kotła wodnego raz ocena jego wpływu na środowisko"
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
"Numeryczna symulacja pracy gazowego kotła wodnego oraz ocena jego wpływu na środowisko"
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
Numeryczna symulacja pracy gazowego kotła wodnego oraz ocena jego wpływu na środowisko
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
Detection of the Direct Sequence Spread Spectrum Signals with BPSK Modulation
PublicationThis paper presents a method of the DS CDMA signals with BPSK modulation detection through the examination of the enhanced signal spectrum density. On the base of experiments carried out on the real radio communication signals the impact of a narrowband emission occurring in the examined frequency band on the detection process effectiveness was shown. The results of the experiment aimed at the detection of the satellite navigation...
-
Numerical methodology for evaluation the combustion and emissions characteristics on WLTP in the light duty dual-fuel diesel vehicle
PublicationThe worldwide aim of reducing environmental impact from internal combustion engines bring more and more stringent emission regulations. In 2017 by EU has been adopted new harmonized test procedure called WLTP. In general terms this test was designed for determining the levels of harmful emissions and fuel consumption of traditional and hybrid cars. This procedure contains specific driving scenarios which representing reallife driving...
-
Soft X-ray Induced Production of Neutral Fragments in High-Rydberg States at the O 1s Ionization Threshold of the Water Molecule
PublicationDissociation of water molecules after soft X-ray absorption can yield neutral fragments in high-Rydberg (HR) states. We have studied the production of such fragments by field ionization and ion time-of-flight (TOF) spectrometry. Neutral HR fragments are created at all resonances below the O 1s ionization potential (IP) and particularly within 1 eV above the O 1s IP. The latter effect is due to the recapture of the O 1s photoelectrons...
-
Asynchronous Charge Carrier Injection in Perovskite Light-Emitting Transistors
PublicationUnbalanced mobility and injection of charge carriers in metal-halide perovskite light-emitting devices pose severe limitations to the efficiency and response time of the electroluminescence. Modulation of gate bias in methylammonium lead iodide light-emitting transistors has proven effective in increasing the brightness of light emission up to MHz frequencies. In this work, a new approach is developed to improve charge carrier...
-
Application a laboratory stand for multi-symptoms tests for high cyclic fatigue of constructional material
PublicationThis paper describes a need of diagnostics present ship plants according to current technical state. In order to reach competent physical quantity describing fatigue of materials by congregated energy. This paper describes using some diagnostics methods (acoustic emission AE, vibration, thermovision, deformation) in order to definition fatigue state of construction material. The author tries to find correlation between measured...
-
Observation of the Hydrogen Migration in the Cation-Induced Fragmentation of the Pyridine Molecules
PublicationThe ability to selectively control chemical reactions related to biology, combustion, and catalysis has recently attracted much attention. In particular, the hydrogen atom relocation may be used to manipulate bond-breaking and new bond-forming processes and may hold promise for far-reaching applications. Thus, the hydrogen atom migration preceding fragmentation of the gas-phase pyridine molecules by the H+, H2+, He+, He2+, and...
-
Temperature influence on tire/road noise evaluated by the drum method
PublicationAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
A white phosphor based on oxyfluoride nano-glass-ceramics co-doped with Eu3+ and Tb3+: Energy transfer study
PublicationStrontium fluoride nanocrystals doped separately with Ln3+ = Eu3+ or Tb3+ ions (95SrF2·5LnF2), as well as co-doped with both the ions (95SrF2·Eu4Tb) were synthesized for comparison. Then, glass-ceramics consisting of the mono-doped or di-doped SrF2 nanocrystals incorporated into amorphous silica (90SiO2·9.5SrF2·0.5Ln or 90SiO2·9.5SrF2·0.1EuF3·0.4Tb) were prepared by sol-gel procedure. The studied materials were characterized by...
-
Spatial distribution of CO2, O2, CO, NO and temperature within a biowaste composting pile
Open Research DataThe dataset contains the color-coded isophlets illustrating the spatial distribution of gas concentrations (CO, CO2, O2 and NO) and the temperature in biowaste composting pile during 6 weeks of process. Four cross sections and two longitudinal cross sections (the left and right sides of the pile) were made using Surfer 10 software (Golden Software,...
-
The luminescence study of Sr3−xBaxP5N10Cl: Eu2+ nitridophosphate.
Open Research DataA series of zeolitic nitridophosphate phosphors Sr2.91−xBaxP5N10Cl:0.09Eu2+ was synthesized by our collaborators from National Taiwan University using a hot isostatic press. Detailed thermal properties were determined using the temperature-dependent photoluminescence intensity and decay time. This research provides a different perspective to analyze...
-
Application of electrochemical sensors and sensor matrixes for measurement of odorous chemical compounds
PublicationIn this paper describes the principle of operation of the electrochemical sensors and the sensor matrixes comprised of electrochemical sensors intended for measurement of odorous compounds. Critical comparison of these sensors’ advantages and disadvantages has been made. The fields of economy contributing to release of odours and the potential sources of their emission have been identified. Commercially available electrochemical...
-
AN OVERVIEW OF HEAT TRANSFER ENHANCEMENT BASED UPON NANOPARTICLES INFLUENCED BY INDUCED MAGNETIC FIELD WITH SLIP CONDITION VIA FINITE ELEMENT STRATEGY
PublicationThe mathematical model of heat generation and dissipation during thermal energy transmission employing nanoparticles in a Newtonian medium is investigated. Dimensionless boundary layer equations with correlations for titanium dioxide, copper oxide, and aluminium oxide are solved by the finite element method. Parameters are varied to analyze their impact on the flow fields. Various numerical experiments are performed consecutively...
-
Activated Carbon Produced by Pyrolysis of Waste Wood and Straw for PotentialWastewater Adsorption
PublicationPyrolysis of straw pellets and wood strips was performed in a fixed bed reactor. The chars, solid products of thermal degradation, were used as potential materials for activated carbon production. Chemical and physical activation processes were used to compare properties of the products. The chemical activation agent KOH was chosen and the physical activation was conducted with steam and carbon dioxide as oxidising gases. The eect...
-
Properties of Nasicon-based CO2 sensor with Bi8Nb2O17 reference electrode
PublicationGas sensors are useful for the carbon dioxide concentration monitoring in many applications. The major challenge is to develop a potentiometric sensor working without the necessity of a reference gas and without a need of the reference electrode encapsulation. Important issue is a selection of reference electrode material, which should provide stable reference potential. For example as reference electrode material in sensor based...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublicationGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
ThreSpect – A Program for the Determination of the Appearance Energies of Neutral and Ionized Species
PublicationCollisions of photons and charged particles with molecules lead to their excitation, ionization, and dissociation into neutral and ionized fragments. Accurately determining thresholds of the formation of particular products plays a vital role in analyzing processes occurring during these interactions. Therefore, we present a computer program, “ThreSpect,” that allows calculating threshold energies of various species generated in...
-
Photophysical processes in the selected white organic light-emitting diodes
PublicationThe first part discusses history of organic emitters, the scope of the work, phenomena in molecular systems, types of architectures in OLEDs, types of OLEDs emitting white light with examples from the literaturę and a description of the parameters chcracterizing LEDs. The second part describes materials, production of the samples, the measurement systems and results. In chapter 8.1 the results for the OLEDs based on emission from...
-
An investigation of selected monoaromatic hydrocarbons released from the surface of polystyrene lids used in coffee-to-go cups
PublicationA consumer trend towards the fast preparation of beverages has increased the popularity of hot beverages (especially coffee and tea) available in disposable containers called coffee-to-go cups with fitted polystyrene lids. Lids in contact with hot beverages may release low molecular weight organic compounds into the gaseous phase causing direct exposure of consumers to these compounds during drinking. The paper describes in detail...
-
AC motor feeding cable consequences on EMC performance of ASD
PublicationHigh level of conducted EMI emissions of adjustable speed drives (ASD) is one of the most difficult problems in contemporary applications. Many investigations are carried out in order to find more effective methods allowing to predict this emission at early stage of design, and therefore to predict adequate countermeasures. This paper deals with the method which allows to estimate by simulation the influence of motor feeding cable...
-
Performance of cryogenic oxygen production unit with exhaust gas bleed for sewage sludge gasification and different oxygen purities
PublicationThe paper presents a thermodynamic analysis of the integration of a cryogenic air separation unit into a negative CO2 emission gas power plant. The power cycle utilizes sewage sludge as fuel so this system fits into the innovative idea of bioenergy with carbon capture and storage. A cryogenic air separation unit integrated with the power plant was simulated in professional plant engineering and thermodynamic process analysis software....
-
Highly sensitive large strain cellulose/multiwalled carbon nanotubes (MWCNTs)/thermoplastic polyurethane (TPU) nanocomposite foams: From design to performance evaluation
PublicationAerogel-based polymer composite foams are promising for large strain piezoresistive sensors, but their aerogel skeleton is partially destroyed during the foaming process, limiting their sensitivity. Herein, the thermoplastic polyurethane was synthesized on the aerogel skeleton to obtain cellulose/multiwalled carbon nanotubes (MWCNTs)/thermoplastic polyurethane (TPU) nanocomposite materials foamed with the aid of supercritical carbon...
-
Pyrolysis Combined with the Dry Reforming of Waste Plastics as a Potential Method for Resource Recovery—A Review of Process Parameters and Catalysts
Publication: Emissions of greenhouse gases and growing amounts of waste plastic are serious environmental threats that need urgent attention. The current methods dedicated to waste plastic recycling are still insufficient and it is necessary to search for new technologies for waste plastic management. The pyrolysis-catalytic dry reforming (PCDR) of waste plastic is a promising pro-environmental way employed for the reduction of both CO2 and...
-
Photocatalysts for Solar Energy Conversion
PublicationPhotocatalytic oxidation over suspended solid photocatalysts (e.g., titanium dioxide) has been proposed as a sustainable process for treatment and purification of water and wastewater as well as the process for photoconversion of solar energy to hydrogen, methane, and other low hydrocarbons. Solar radiation could be used to drive heterogeneous electrochemical reactions at the surface of an optically active photocatalyst (e.g.,...