Search
Search results for: FEM SIMULATIONS
-
Rebuilding Bailey Bridge to Bridge With Bascule Span – A Case Study
PublicationThe structural analysis of a road foldable prefabricated steel Bailey- type bridge located over the Tuga River in Żelichowo, Poland is performed in this paper. Interesting and untypical bridge redevelopment performed made it possible to lift the middle foldable bridge span by approximately 4.0 m concerning the existing state. The paper begins with a survey of literature carried out on the investigations of foldable Bailey-type...
-
Validation of lumbar spine finite element model
Open Research DataThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research....
-
Modelling of Longitudinal Elastic Wave Propagation in a Steel Rod Using the Discrete Element Method
PublicationThe paper deals with the issue of modelling elastic wave propagation using the discrete element method (DEM). The case of a longitudinal wave in a rod with a circular cross-section was considered. A novel, complex algorithm consisting of the preparation of models and simulation of elastic waves was developed. A series of DEM models were prepared for simulations, differing in discretisation and material parameters. Additional calculations...
-
A PRELIMINARY STUDY ON THE OPTIMAL CHOICE OF AN IMPLANT AND ITS ORIENTATION IN VENTRAL HERNIA REPAIR
PublicationThis paper addresses the problem of ventral hernia repair. The main goals are to find an optimal surgical mesh for hernia repair and to define its optimal orientation in the abdominal wall to minimise the maximum force at the tissue-implant juncture. The optimal mesh is chosen from a set of orthotropic meshes with different stiffness ratios for typical hernia placement in the abdominal area. The implant is subjected to an anisotropic...
-
Testing of the longest span soil-steel bridge in Europe – new quality in measurements
PublicationThe article describes interdisciplinary and comprehensive diagnostic tests of final bridge inspection and acceptance proposed for a soil – steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure response was collected. The load test design was based on the nonlinear numerical simulations performed by...
-
Thermal analysis of Magnetohydrodynamics (MHD) Casson fluid with suspended Iron (II, III) oxide-aluminum oxide-titanium dioxide ternary-hybrid nanostructures
PublicationThis study is carried out to enhance and analyze the thermal performance of non-Newtonian Casson fluid by immersing Ternary hybrid nanoparticles Fe3O4-Al2O3-TiO2 uniformly. To model the behaviour of such complex phenomena mathematically, a system of complex transport differential equations is developed by utilizing a non-Fourier heat transfer model for energy transport. The non-dimensional system of transport equations involving...
-
Validation Process for Computational Model of Full-Scale Segment for Design of Composite Footbridge
PublicationExperimental tests and numerical simulations of a full-scale segment of a foot and cycle bridge made of polymer composites are presented in the paper. The analysed structure is made of sandwich panels, which consist of glass fibre reinforced polymer (GFRP) multi-layered laminate faces and a PET foam (obtained from recycling) core. The dimensions of the segment cross-section are the same as for the target footbridge; however, span...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublicationThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
Parametrized Local Reduced-Order Models With Compressed Projection Basis for Fast Parameter-Dependent Finite-Element Analysis
PublicationThis paper proposes an automated parametric local model-order reduction scheme for the expedited design of microwave devices using the full-wave finite-element method (FEM). The approach proposed here results in parameterized reduced-order models (ROMs) that account for the geometry and material variation in the selected subregion of the structure. In each subregion, a parameter-dependent projection basis is generated by concatenating...
-
Towards Understanding of Mechanics of Hernia Managed by Synthetic Mesh in Laparoscopic Operation: A Single Case Study
PublicationIn this paper a research towards understanding of mechanics of ventral hernia operated with the use of Physiomesh Open image in new window implant and SecureStrap Open image in new window staples is described. Experimental and numerical studies are conducted for that purpose. Experimental works cover uni-axial tension tests of the implant samples and of the implant-staples-tissue system. Also experiments on implant-staples-tissue...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Why is TASK Quarterly a Significant Journal to Publish Your Article? —A Bibliometric Analysis of a Scientific and Technical Journal
PublicationA bibliometric analysis of TASK Quarterly in the years 1997-2021 in terms of various bibliometric indicators was performed to celebrate the 25th anniversary of the publication of the first issue of the journal. The number of publications and citations increased over the mentioned span of years. The leading countries in terms of the greatest number of papers published in TASK Quarterly are Poland, Italy, Germany, Ukraine, USA and...
-
The effect of fishing basin construction on the behaviour of a footbrdge over the port channel
PublicationThe paper analyses possible causes of failure of the rotating footbridge over the Ustka port channel. In July, 2015, strange behaviour of this object was observed in the form of excessive vibrations of bridge platform suspension rods, with the accompanying acoustic effects. A preliminary geotechnical analysis has revealed that this destructive effect was caused by the nearby construction works, namely construction of a fishing...
-
The use of a two-phase Monte Carlo material model to reflect the dispersion of asphalt concrete fracture parameters
PublicationThe work covers comprehensive laboratory tests of semi-circular bending (SCB) of asphalt concrete samples. The results of two test series, including four and 32 SCB specimens, indicate a substantial scatter of force–deflection (F-d) histories. The numerical analysis is aimed to reflect the maximum breaking load and fracture energy of the samples, pointing out their random character. The original simulation-based fictitious Monte...
-
Size effect in concrete beams under bending – influence of the boundary layer and the numerical description of cracks
PublicationIn the paper the size effect phenomenon in concrete is analysed. The results of numerical simulations of using FEM on geometrically similar un-notched and notched concrete beams under bending are presented. Concrete beams of four different sizes and five different notch heights under three-point bending test were simulated. In total 18 beams were analysed. Two approaches were used to describe cracks in concrete. First, eXtended...
-
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublicationThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
NUMERICAL MODEL QUALITY ASSESSMENT OF OFFSHORE WIND TURBINE SUPPORTING STRUCTURE BASED ON EXPERIMENTAL DATA
PublicationAs a structure degrades some changes in its dynamical behavior can be observed, and inversely, observation and evaluation of these dynamical changes of the structure can provide information of structural state of the object. Testing of the real structure, besides of being costly, can cover only limited working states. It is particularly considerable in case of hardly accessible, and randomly/severely dynamically loaded offshore...
-
QRS Morphology-Based EDR Signal—Factors Determining its Properties
PublicationRespiration-induced signals contain a clinically significant information. It could be obtained utilizing both direct and indirect methods. ECG-Derived Respiration (EDR) method is the latter one. However, in this case, two approaches could be distinguished. First one is based on determining changes in the morphology of QRS complexes while the second one is based on the Respiratory Sinus Arrhythmia (RSA) mechanism. The former approach...
-
Atomic-Scale Finite-Element Modeling of Elastic Mechanical Anisotropy in Finite-Sized Strained Phosphorene Nanoribbons
PublicationNanoribbons are crucial nanostructures due to their superior mechanical and electrical properties. This paper is devoted to hybrid studies of the elastic mechanical anisotropy of phosphorene nanoribbons whose edges connect the terminals of devices such as bridges. Fundamental mechanical properties, including Young’s modulus, Poisson’s ratio, and density, were estimated from first-principles calculations for 1-layer, 3-layer, and...
-
Results of the “DPDT-Auger” Research Project on Screw Displacement Piles
PublicationThe main objective of the “DPDT-Auger” research project was to test the prototype DPDT auger for forming screw displacement piles in the ground (patented in Poland in 2020). An additional aim was to develop design methods and rules for the making of such piles. The augers and piles were first tested on a model scale, and then more extensively in the real scale on experimental field plots. The results found the overall functionality...
-
Numerical tests of time-stepping schemes in the context of FEM for 6-field shell dynamics
PublicationThe paper deals with integration of dynamic equations of irregular shells performed with relatively long time steps. Numerical instability appearing often in this kind of analysis motivated the authors to present some studies based on numerical tests referring to convergence problems of finite element analysis as well the applied stability conditions. The analysis is carried out on simulations of shell dynamics with the where the...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Cost-Effective and Sufficiently Precise Integration Method Adapted to the FEM Calculations of Bone Tissue
PublicationThe technique of Young’s modulus variation in the finite element is not spread in biomechanics. Our future goal is to adapt this technique to bone tissue strength calculations. The aim of this paper is to present the necessary studies of the element’s integration method that takes into account changes in material properties. For research purposes, a virtual sample with the size and distribution of mechanical properties similar...
-
Oddziaływania taboru na mosty kolejowe przy zmiennych parametrach ruchu
PublicationW pracy poruszono zagadnienia związane z identyfikacją oraz modelowaniem układu dynamicznego most-pojazd ruchomy. Za element szczególnie istotny uznano czynnik obciążający. Opracowano i wdrożono metodykę identyfikacji cech dynamicznych rzeczywistego pojazdu szynowego. Eksperyment badawczy przeprowadzono dla jednostki trakcyjnej EN57, jednak nie ma żadnych ograniczeń w stosowaniu metody dla innego, konwencjonalnego taboru szynowego....
-
Development and validation of lumbar spine finite element model
PublicationThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research. A FE model of the 50th percentile adult male (AM) Total Human Model for Safety...
-
Stateczność i niezawodność pełnomorskich platform wiertniczych
PublicationW pracy przedstawiono wieloletnie doświadczenia Autora w zakresie wybranych aspektów numerycznej analizy pełnomorskich platform wiertniczych, w szczególności stacjonarnych platform stalowych poddanych działaniu fal wiatrowych i wiatru. W opisie zachowania się platform uwzględniono współoddziaływanie trzech ośrodków: materiału konstrukcji, morskich fal wiatrowych i podłoża gruntowego. Przyjęcie do opisu stochastycznych właściwości...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Piezoelectric Transducer for Mechanical Assessment of Soft Tissues. Concept, Implementation and Analysis
PublicationThe main goal of this work was following: preparation of a new concept, implementation and analysis of the piezoelectric resonant sensor/actuator for measuring the aging process of human skin. The research work has been carried out in the framework of cooperation between the INP-ENSEEIHT-LAPLACE, Toulouse, France, and at the Gdansk University of Technology, Faculty of Electrical and Control Engineering, Research Group of...
-
Macromodeling techniques for accelerated finite element analysis
PublicationThis paper deals with the Model Order Reduction applied locally in the Finite Element Method (FEM) analysis. Due to the reduction process, blocks of FEM system matrices associated with selected subregions of the computational domain are projected onto the subspaces spanned by the vectors of suited orthogonal projection basis. In effect, large and sparse FEM matrices are replaced with small and dense ones, called macromodels. This...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublicationThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
A spline-based FE approach to modelling of high frequency dynamics of 1-D structures
PublicationIn this paper a computational methodology leading to the development of a new class of FEs, based on the application of continuous and smooth approximation polynomials, being splines, has been presented. Application of the splines as appropriately defined piecewise elemental shape functions led the authors to the formulation of a new approach for FEM, named as spFEM, where contrary to the well-known NURBS approach, the boundaries...
-
FEM Calculations in Analysis of Steel Subsea Water Injection Flowlines Designing Process
PublicationPaper describes the result of theoretical research aimed at assessing the loads and operating conditions of a Coiled Tubing pipeline injecting water, suspended to the mining platform of Lotos Petrobaltic. For this purpose, appropriate calculation models have been developed using the Finite Element Method (FEM), taking into account the nature of the analyzed object and its loads. The analyzes were carried out for two pipes (previously...
-
Modal FEM Analysis of Ferrite Resonant Structures
PublicationThe finite-element method (FEM) is applied for modal analysis of ferrite-loaded spherical resonators. To improve the efficiency of the numerical calculations, the body-of-revolution (BOR) technique is utilized. Due to the frequency-dependent ferrite permeability, FEM leads to a nonlinear eigenvalue problem that is challenging to solve. To this end, Beyn’s method is proposed. The effectiveness of the proposed approach is confirmed...
-
GPU-accelerated finite element method
PublicationIn this paper the results of the acceleration of computations involved in analysing electromagnetic problems by means of the finite element method (FEM), obtained with graphics processors (GPU), are presented. A 4.7-fold acceleration was achieved thanks to the massive parallelization of the most time-consuming steps of FEM, namely finite-element matrix-generation and the solution of a sparse system of linear equations with the...
-
Structural response of existing spatial truss roof construction based on Cosserat rod theory
PublicationPaper presents the application of the Cosserat rod theory and newly developed associated finite elements code as the tools that support in the expert-designing engineering practice. Mechanical principles of the 3D spatially curved rods, dynamics (statics) laws, principle of virtual work are discussed. Corresponding FEM approach with interpolation and accumulation techniques of state variables are shown that enable the formulation...
-
Numerical modelling of 3D printout using line (1D) elements
PublicationA proposition of some numerical modelling of the 3D printout is presented in the paper. The proposed model is composed of some 1D elements. The resulting numerical model of the infill consist of beam, spring and rigid elements. Obtained results confirm correctness of the proposed modelling method. Two methods of estimation of the spring parameters are proposed in the paper. In the first method, mechanical properties of the connecting...
-
Damage Analysis of Tensioning Cable Anchorage Zone of a Bridge Superstructure, Using CDP Abaqus Material Model
PublicationNumerical analysis of the tensioning cables anchorage zone of a bridge superstructure is presented in this paper. It aims to identify why severe concrete cracking occurs during the tensioning process in the vicinity of anchor heads. In order to simulate the tensioning, among others, a so-called local numerical model of a section of the bridge superstructure was created in the Abaqus Finite Element Method (FEM) environment. The...
-
Finite element modelling of a historic church structure in the context of a masonry damage analysis
PublicationThe paper includes a case study of modelling a real historic church using the finite element method (FEM) based on laser scans of its geometry. The main goal of the study was the analysis of the causes of cracking and crushing of masonry walls. An FEM model of the structure has been defined in ABAQUS. A non-linear dynamic explicit analysis with material model including damage plasticity has been performed. A homogenization procedure...
-
Reduction of Derivative pipeline effort in water turbine
PublicationThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
In-plane shear nonlinearity in failure behavior of angle-ply laminated shells
PublicationThe paper concerns the progressive failure analysis of laminates with the in-plane shear nonlinearity accounted for.The nonlinear shear response of the layer is described by the constitutive relation treating the stresses as a function of strains. Thus it can be easily incorporated into the displacement-based FEM codes. The brittle failure mechanisms of the fibers and the matrix of the layer are recognized with the use of the Hashin...
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublicationThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
Sophistication assessment of existing FEM models of orbital blowout trauma: Is models valuation justified?
PublicationAfter a thorough study of the work entitled “Development and validation of an optimized finite element model of the human orbit”, some doubts aroused concerning the sophistication assessment of the existing finite element method (FEM) models of orbital blow-out. Although the work was unquestionably innovative, and the results were not only fascinating but also invaluable, the authors stated that their model was the most sophisticated...
-
Multidisciplinary approach to the assessment of historic structures based on the case of a masonry bridge in Galicia (Spain)
PublicationThe paper presents a general method to evaluate a masonry structure with a complex geometry and unknown material properties. This multidisciplinary approach integrates close range digital photogrammetry,ground probing radar (GPR) and finite elements analysis (FEM) to analyse a masonry bridge. The resulting information from photogrammetry and radar is applied to define a 3D model, which is then used to simulate the behaviour of...
-
Calculation of Resonance in Planar and Cylindrical Microstrip Structures Using a Hybrid Technique
PublicationA hybrid technique was employed for the analysis of the resonance frequency of thin planar and cylindrical microstrip structures with the patches of arbitrary geometry. The proposed technique utilizes a combination of Galerkin’s moment method and a finite-element method (FEM). In this approach, an FEM is adopted to calculate the patch surface current densities, and a method of moments is utilized to calculate the resonance frequencies...
-
SHM System of the Roof Structure of Sports Arena “Olivia”
PublicationThe paper presents a structural health monitoring system of the Sports Arena “Olivia” in Gdansk, Poland. The system was installed because of doubts about the roof stability due to observed buckling of the steel truss members. The SHM system was based on nonlinear FEM models used for detection of type of near failure modes of the roof. The application of detailed FEM model in current state updated on data from in situ loading testes...
-
Inverse Analysis as a Key Element of Safety Assessment under the Snow Load For The Large Suspension Roofs Structure
PublicationThe paper presents a concept and realization of monitoring system for the Silesian Stadium in Chorzow. The idea of the system lies in fusion of structure monitoring with a calibrated numerical FEM model [1]. The inverse problem is solved. On the base of measured selected displacements, the numerical FEM model of the structure combined with iterative method, develops the current snow load distribution. Knowing the load, we can calculate...
-
FEM simulation of laminate failure in the three point bending
PublicationThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Theoretical analysis of the cable-stayed bridge over brda river in Bydgoszcz
PublicationThe topic of this article is the numerical analysis carried out for the cable-stayed tram (road) bridge over Brda river in Bydgoszcz. The goal of numerical studies was the verification of project assumptions and construction solutions elaborated by the autonomous team. The bridge calculations were conducted on three independent FEM models The internal forces and the elements effort under different loading schemes were examined....
-
Electromagnetic Simulation with 3D FEM for Design Automation in 5G Era
PublicationElectromagnetic simulation and electronic design automation (EDA) play an important role in the design of 5G antennas and radio chips. The simulation challenges include electromagnetic effects and long simulation time and this paper focuses on simulation software based on finite-element method (FEM). The state-of-the-art EDA software using novel computational techniques based on FEM can not only accelerate numerical analysis, but...