Search
Search results for: MICROSTRUCTURE-PROCESSING-PERFORMANCE PROPERTIES RELATIONSHIPS
-
Multicomponent layers for aluminium alloys surface consolidation
PublicationThe main reason of the surface modification of the components such as pistons and cylinder blocks made of cast aluminium alloys is to obtain high hardness, wear and corrosion resistance of the working surface for larger lifetime of the motor-car and aircraft engines. In that aspect, the new conception of development - by hybrid method - of surface layers containing manganese, nitrogen, sulphur (Mn-N-S) and manganese, nitrogen,...
-
On the correlation between magnetoacoustic emission and magnetostriction dependence on the applied magnetic field
PublicationThe correlation between magnetoacoustic emission signal envelopes and magnetostriction curves is investigated. Two sets of samples are being considered: tempered martensitic steel and plastically deformed ferritic steel. It is shown that even though some general relations may be observed, as was demonstrated in the literature, the correlation is not always present. One may not expect to change both quantities in the same way if...
-
Cellulose Nanofibers Isolated from the Cuscuta Reflexa Plant as a Green Reinforcement of Natural Rubber
PublicationIn the present work, we used the steam explosion method for the isolation of cellulose nanofiber (CNF) from Cuscuta reflexa, a parasitic plant commonly seen in Kerala and we evaluated its reinforcing efficiency in natural rubber (NR). Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Thermogravimetric analysis (TGA) techniques...
-
MEMS Technology Evaluation for Submerged Vehicle Navigation
PublicationAnalysis of some vital aspects of inertial navigation using MEMS. The paper presents a few aspects of MEMS gyro errors, and their estimation process in the context of INS processing flow. These errors have a serious impact on overall inertial system performance. The results of undertaken researches in that area, and pointing out the main difficulties behind the INS when using a few top MEMS technologies, including sophisticated...
-
Characterization of volatile compounds, structural, thermal and physico-mechanical properties of cross-linked polyethylene foams degraded thermo-mechanically at variable times
PublicationWaste cross-linked polyethylene foam (wXLPE) was thermo-mechanically degraded at variable time using internal batch mixer. The progress of wXLPE degradation has been investigated by using a simultaneous thermogravimetric/differential scanning calorimetry analyzer coupled with Fourier transform infrared spectroscopy, swelling measurements, tensile tests and scanning electron microscopy. Volatile organic compounds generated during...
-
Performance and Security Testing for Improving Quality of Distributed Applications Working in Public/Private Network Environments
PublicationThe goal of this dissertation is to create an integrated testing approach to distributed applications, combining both security and performance testing methodologies, allowing computer scientist to achieve appropriate balance between security and performance charakterstics from application requirements point of view. The constructed method: Multidimensional Approach to Quality Analysis (MA2QA) allows researcher to represent software...
-
A recent developments in polyurethane foams containing a low-cost and pro-ecological modifiers
PublicationDiversity of the polyurethane (PU) foams applications cause that investigation of the relationships between their structure and properties is currently very popular topic among the many research institutions and companies. At the turn of the last years many scientific papers about PU foams and their composites were published. The one of the main research trends in this field is related to the reduction of production costs of...
-
Tacit Knowledge Sharing and Personal Branding. How to Derive Innovation From Project Teams?
PublicationInnovation, relationships, cooperation, and knowledge are key factors which determine a competitive advantage in the networked economy. A network serves as a contemporary form of market process coordination. Network economy, according to the idea of prosumerism, is founded on collaboration of individual creators based on a network of values instead of hierarchical dependencies. Another feature of a network is that it imposes symmetry...
-
Sea ice floe size and shape data from a very high resolution satellite image (Knox Coast, East Antarctica)
Open Research DataThis dataset contains floe size distribution data from a very high resolution (pixel size: 0.3 m) optical satellite image of sea ice, acquired on 16. Feb. 2019 off the Knox Coast (East Antarctica). The image shows relatively small ice floes produced by wave-induced breakup of landfast ice between the Mill Island and Bowman Island. The ice floes are...
-
Material Flow Analysis in a cooked mussel processing industry
PublicationGalicia (NW Spain) is an ideal environment for mussel culture owing to its excellent natural conditions. It is the first Spanish and European mussel producer and the second worldwide after China. More than 50% of the mussel collected in Galicia is used in the processing industry, which produces different products, as cooked mussel that is canned, frozen or used in the food industry. In this paper a methodology based on Life Cycle...
-
Poloxamer: A versatile tri-block copolymer for biomedical applications
PublicationPoloxamers, also called Pluronic, belong to a unique class of synthetic tri-block copolymers containing central hydrophobic chains of poly(propylene oxide) sandwiched between two hydrophilic chains of poly(ethylene oxide). Some chemical characteristics of poloxamers such as temperature-dependent self-assembly and thermo-reversible behavior along with biocompatibility and physiochemical properties make poloxamer-based biomaterials...
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublicationLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
By-Products from Food Industry as a Promising Alternative for the Conventional Fillers for Wood–Polymer Composites
PublicationThe present paper describes the application of two types of food-industry by-products, brewers’ spent grain (BSG), and coffee silverskin (ŁK) as promising alternatives for the conventional beech wood flour (WF) for wood–polymer composites. The main goal was to investigate the impact of partial and complete WF substitution by BSG and ŁK on the processing, structure, physicochemical, mechanical, and thermal properties of resulting...
-
Wpływ polietylenu szczepionego bezwodnikiem maleinowym oraz sił ścinających na właściwości mieszanin polietylen wysokiej gęstości-miał gumowy
PublicationScharakteryzowano wpływ kompatybilizatora w postaci polietylenu szczepionego bezwodnikiem maleinowym na właściwości mieszanin PE-HD–miał gumowy. Kompozycje termoplastyczne zawierające 50 cz. mas. rozdrobnionych odpadów gumowych, otrzymano przy użyciu współbieżnej wytłaczarki dwuślimakowej. Poziom sił ścinających generowanych podczas mieszania, regulowano za pomocą zmian prędkości obrotowych ślimaków. Przeprowadzono charakterystykę...
-
Digital structures for high-speed signal processing
PublicationThe work covers several issues of realization of digital structures for pipelined processing of real and complex signals with the use of binary arithmetic and residue arithmetic. Basic rules of performing operations in residue arithmetic are presented along with selected residue number systems for processing of complex signals and computation of convolution. Subsequently, methods of conversion of numbers from weighted systems to...
-
Material characterisation of biaxial glass-fibre non-crimp fabrics as a function of ply orientation, stitch pattern, stitch length and stitch tension
PublicationDue to their high density-specific stiffnesses and strength, fibre reinforced plastic (FRP) composites are particularly interesting for mobility and transport applications. Warp-knitted non-crimp fabrics (NCF) are one possible way to produce such FRP composites. They are advantageous because of their low production costs and the ability to tailor the properties of the textile to the reinforcement and drape requirements of the application....
-
Characterization of CaTi0.9Fe0.1O3/La0.98Mg0.02NbO4 composite
PublicationA composite of CaTi0.9Fe0.1O3 and electrolyte material, i.e. magnesium doped La0.98Mg0.02NbO4 was prepared and studied. The phase content and the sample microstructure was examined by an X-ray diffraction method and scanning electron microscopy. EDS measurements were done both for composite samples and the diffusion couple. The electrical properties were studied by four terminal DC method. The Ahigh-temperature interaction between...
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublicationMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Chitosan/poly(4-vinylpyridine) coatings formed on AgNPs-decorated titanium
PublicationElectrophoretic deposition (EPD) of chitosan/poly(4-vinylpyridine) (chit/P4VP) coatings on titanium substrates previously decorated with silver nanoparticles (AgNPs) was performed at different content of P4VP in the suspension and different voltage values. The results revealed that the composite coatings were formed, well-adjacent to the titanium substrate, of suitable roughness, hydrophilicity, and corrosion resistance. The voltage...
-
Influence of Nitriding and Laser Remelting on Properties of Austenitic Stainless Steel Type X10CrNi18-8 and Cavitation Erosion Resistance
PublicationThe paper presents properties of surface layers. Surface layers were obtained by using low temperature glow–discharge nitriding process and laser remelting carried out on austenitic stainless steel type X10CrNi18-8. Investigations were done by using an Ultra Nanoindentation Tester (UNHT) in the Warsaw Institute of Fundamental Technological Research. The influence of the above mentioned...
-
Visual Attention Distribution Based Assessment of User's Skill in Electronic Medical Record Navigation
PublicationCurrently, the most precise way of reflecting the skills level is an expert’s subjective assessment. In this paper we investigate the possibility of the use of eye tracking data for scalar quantitative and objective assessment of medical staff competency in EMR system navigation. According to the experiment conducted by Yarbus the observation process of particular features is associated with thinking. Moreover, eye tracking is...
-
Performance Analysis of the OpenCL Environment on Mobile Platforms
PublicationToday’s smartphones have more and more features that so far were only assigned to personal computers. Every year these devices are composed of better and more efficient components. Everything indicates that modern smartphones are replacing ordinary computers in various activities. High computing power is required for tasks such as image processing, speech recognition and object detection. This paper analyses the performance of...
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublicationThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...
-
Adaptive Wavelet-Based Correction of Non-Anechoic Antenna Measurements
PublicationNon-anechoic measurements represent an affordable alternative to evaluation of antenna performance in expensive, dedicated facilities. Due to interferences and noise from external sources of EM radiation, far-field results obtained in non-ideal conditions require additional post-processing. Conventional correction algorithms rely on manual tuning of parameters, which make them unsuitable for reliable testing of prototypes. In this...
-
Machine Learning in Multi-Agent Systems using Associative Arrays
PublicationIn this paper, a new machine learning algorithm for multi-agent systems is introduced. The algorithm is based on associative arrays, thus it becomes less complex and more efficient substitute of artificial neural networks and Bayesian networks, which is confirmed by performance measurements. Implementation of machine learning algorithm in multi-agent system for aided design of selected control systems allowed to improve the performance...
-
Processing, mechanical and thermal behavior assessments of polycaprolactone/agricultural wastes biocomposites
PublicationIn this paper, brewer’s spent grain (BSG) was applied as potential lignocellulose biofiller in biocompos-ites based on polycaprolactone (PCL). The PCL/BSG biocomposites filled with varying content of biofillerswere prepared via low-temperature melt-compounding. These conditions allow limiting thermal degra-dation of used biofillers during processing. The influence of biofiller content (ranging from 25 to 200parts by weight on 100...
-
Multi-Criterial Design of Antennas with Tolerance Analysis Using Response-Feature Predictors
PublicationImperfect manufacturing is one of the factors affecting the performance of antenna systems. It is particularly important when design specifications are strict and leave a minimum leeway for a degradation caused by geometry or material parameter deviations from their nominal values. At the same time, conventional antenna design procedures routinely neglect to take the fabrication tolerances into account, which is mainly a result...
-
Silicon Oxycarbide (SiOC) Ceramic Materials as Anodes for Lithium Ion Batteries
PublicationPolymer derived ceramics (PDCs) have attracted attention as alternative anode material for Li-ion batteries. It has been found that ternary SiOC and SiCN ceramics obtained through pyrolysis of various preceramic polymers display high reversible capacities of 500 – 650 mAh/g. In this work we try to correlate the electrochemical performance of polymer derived silicon oxycarbide with its chemical composition and microstructural features....
-
Laser-assisted approach for improved performance of Au-Ti based glucose sensing electrodes
PublicationThis paper focuses on the synthesis route and electrochemical properties of electrocatalytic material based on gold nanoparticles (NPs) embedded in a structured titanium template obtained via optimized anodization, chemical etching and laser processing. SEM inspection reveals the presence of Au NPs (60–90 nm in diameter) sited in the titanium foil cavities. Performed electrochemical measurements enable nomination of the set of working...
-
TRAFFIC MODEL OF A MULTIDOMAIN IMS/NGN
PublicationIn this paper we continue our research and present an analytical traffic model of a multidomain Next Generation Network (NGN), which is standardized for delivering multimedia services based on the IP Multimedia Subsystem (IMS). The model takes into account several service scenarios (including registration, intra- and inter-operator calls) and a large set of network parameters. Using the model mean Call Set-up Delay and mean Call...
-
Application of fiber optic sensors using Machine Learning algorithms for temperature measurement of lithium-ion batteries
PublicationOptical fiber sensorsusing low-coherence interferometry require processing ofthe output spectrum or interferogramto quickly and accurately determine the instantaneous value of the measured quantity, such as temperature.Methods based on machine learning are a good candidate for this application. The application of four such methods in an optical fiber temperature sensoris demonstrated.Using aZnO-coated...
-
Tuning Electrochemical Performance by Microstructural Optimization of the Nanocrystalline Functional Oxygen Electrode Layer for Solid Oxide Cells
PublicationFurther development of solid oxide fuel cell (SOFC) oxygen electrodes can be achieved through improvements in oxygen electrode design by microstructure miniaturisation alongside nanomaterials implementation. In this work, improved electrochemical performance of an La0.6Sr0.4Co0.2Fe0.8O3-d (LSCF) cathode was achieved by the controlled modification of the La0.6Sr0.4CoO3-d (LSC) nanocrystalline interlayer introduced between a porous...
-
Ongoing Progress on Pervaporation Membranes for Ethanol Separation
PublicationEthanol, a versatile chemical extensively employed in several fields, including fuel production, food and beverage, pharmaceutical and healthcare industries, and chemical manufacturing, continues to witness expanding applications. Consequently, there is an ongoing need for cost-effective and environmentally friendly purification technologies for this organic compound in both diluted (ethanol-water–) and concentrated solutions (water-ethanol–)....
-
Impact of information systems (IS) infusion on Open Government Data (OGD) adoption
PublicationPurpose – This study aims to underline the possible influence of the moderator, information systems (IS) infusion, on Open Government Data (OGD) adoption and usage. Design/methodology/approach – Using the partial least squares-structural equation modeling methodological approach, the adapted unified theory of acceptance and use of technology (UTAUT) model has been used for understanding the role of themoderating variable, namely,...
-
Analysis of server-side and client-side Web-GIS data processing methods on the example of JTS and JSTS using open data from OSM and geoportal
PublicationThe last decade has seen a rapid evolution of processing, analysis and visualization of freely available geographic data using Open Source Web-GIS. In the beginning, Web-based Geographic Information Systems employed a thick-client approach which required installation of platform-specific browser plugins. Later on, research focus shifted to platform-independent thin client solutions in which data processing and analysis was performed...
-
Proposal of New Starch-Blends Composition Quickly Degradable in Marine Environment
PublicationThe aim of this paper was to obtain a quickly degradable in seawater polymer blend as an alternative proposal for classical polymer packaging. For preliminary studies: poly(lactic acid) (PLA), starch, calcium carbonate (CaCO3), gelatin and glycerol were chosen. PLA was pointed out due to its biodegradability and comparable properties to polyethylene or polypropylene. Whereas starch was chosen as abundant, renewable and cheap polymer...
-
rigid polyurethane foams modified with selected nanofillers
PublicationThe nanofillers: natural montmoryllonite (MMT) - Bentonite, natural MMT modified with a quaternary ammonium salt - Cloisite30B, has been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (density, water absorption, brittleness and compression strength) and thermal properties (thermal stability, fire behaviours) of such foams has been analysed. The...
-
Selected results of measurements carried out in a ship power station with two generators working in parallel with the use of the NI PXIe-1062Q based measurement system
Open Research DataThe presented dataset is part of research focusing on the assessment of metrological properties of the instrument, Estimator/Analyzer (A/E v.2), developed and made at the Faculty of Electrical Engineering, Department of Marine Electrical Power Engineering, of Gdynia Maritime University. The attached data set contains the results of measurements made...
-
Properties of nano-Fe3O4 incorporated epoxy coatings from Cure Index perspective
PublicationThe mission of an advanced epoxy-based nanocomposite coating is to provide a given substrate with protection against an unwelcome guest; e.g. corrosive molecules/media, environmental stress, flame, thermal degradation or microorganisms. In such systems, the degree to which superior properties can be guaranteed depends on the state of network formation in the epoxy in the presence of nanoparticles. For low-filled epoxy nanocomposite coatings,...
-
Nonlinear and linear impedance of bismuth vanadate ceramics and its relation to structural properties
PublicationThe nonlinear and linear electrical properties, topography, and microstructure of bismuth-vanadate ceramics, were studied. The structurewas observed with the use of X-ray diffraction (XRD), scanning electronmicroscopy (SEM), atomic force microscopy (AFM) and confocal microscopy methods. The obtained results showed that ceramic is porous. Two phase transitionswere determinedwith the use of DSC measurements. The linear and nonlinear ac...
-
Effects of Laser Remelting at Cryogenic Conditions on Microstructure and Wear Resistance of the Ti6Al4V Alloy Applied in Medicine
PublicationThe titanium and its alloys can be subjected to surface treatment, including laser treatment. In this work a new laser treatment at cryogenic conditions of Ti6Al4V alloy has been described. The work has been aimed at establishing whether such surface treatment could be suitable for implants working under wear in biological corrosive environment. The remelting has been made with the use of CO2 continuous work laser at laser power...
-
Synthesis and thermal studies of flexible polyurethane nanocomposite foams obtained using nanoclay modified with flame retardant compound
PublicationThis work presents thermal studies of nanocomposites based on the flexible polyurethane (PU) matrix and filled using montmorillonite organically modified with organophosphorus flame retardant compound. Flexible PU nanocomposite foams were prepared in the reaction carried out between reactive alcoholic hydroxyl and isocyanate groups with the ratio of NCO to OH groups equal to 1.05. The amount of an organoclay ranging from 3 to 9...
-
Portable Raman spectrometer - design rules and applications
PublicationRaman spectroscopy has become more popular due to its new prospective field applications in forensic sciences, war against terrorism, environment protection and other field chemical analysis. Raman spectrometers can be miniaturised to portable devices and their price is decreasing due to development of optoelectronics components. Unfortunately, this technology has still numerous limitations that influence their design and limit...
-
Elimination of Impulsive Disturbances From Archive Audio Signals Using Bidirectional Processing
PublicationIn this application-oriented paper we consider the problem of elimination of impulsive disturbances, such as clicks, pops and record scratches, from archive audio recordings. The proposed approach is based on bidirectional processing—noise pulses are localized by combining the results of forward-time and backward-time signal analysis. Based on the results of specially designed empirical tests (rather than on the results of theoretical analysis),...
-
Deterioration of masonry structure investigated by a thermal camera with a qualitative assessment of thermal image processing
PublicationThermal imaging is contemporary remote sensing measurement technique, which provides an image of the temperature distribution in the measured object. The method is widely used, due to its mobility as well as the non-destructive character of the measurement. Infrared thermography is especially relevant in the inspection of insulation, what is more, it is a suitable device for detecting thermal bridges and structural changes, which...
-
NVRAM as Main Storage of Parallel File System
PublicationModern cluster environments' main trouble used to be lack of computational power provided by CPUs and GPUs, but recently they suffer more and more from insufficient performance of input and output operations. Apart from better network infrastructure and more sophisticated processing algorithms, a lot of solutions base on emerging memory technologies. This paper presents evaluation of using non-volatile random-access memory as a...
-
Tuning matrix-vector multiplication on GPU
PublicationA matrix times vector multiplication (matvec) is a cornerstone operation in iterative methods of solving large sparse systems of equations such as the conjugate gradients method (cg), the minimal residual method (minres), the generalized residual method (gmres) and exerts an influence on overall performance of those methods. An implementation of matvec is particularly demanding when one executes computations on a GPU (Graphics...
-
Network-assisted processing of advanced IoT applications: challenges and proof-of-concept application
PublicationRecent advances in the area of the Internet of Things shows that devices are usually resource-constrained. To enable advanced applications on these devices, it is necessary to enhance their performance by leveraging external computing resources available in the network. This work presents a study of computational platforms to increase the performance of these devices based on the Mobile Cloud Computing (MCC) paradigm. The main...
-
Inertial Sensors Applications in Underwater Measurements
PublicationOver the past decades microelectromechanical systems (MEMS) researchers have demonstrated a number of microsensors for almost every possible sensing modality, including attitudes. Current MEMS inertial measurement units (IMU) come in many shapes, sizes, and costs — depending on the application, and performance required. MEMS sensors have proved and demonstrated performance exceeding those of their macroscale counterpart sensors. In...
-
Integration, Processing and Dissemination of LiDAR Data in a 3D Web-GIS
PublicationThe rapid increase in applications of Light Detection and Ranging (LiDAR) scanners, followed by the development of various methods that are dedicated for survey data processing, visualization, and dissemination constituted the need of new open standards for storage and online distribution of collected three-dimensional data. However, over a decade of research in the area has resulted in a number of incompatible solutions that offer...