displaying 1000 best results Help
Search results for: 9CR-1MO STEEL
-
Efect of ageing on microstructure and impact properties of 9Cr-1Mo steel
PublicationBadano wpływ długotrwałego starzenia na mikrostrukturę i właściwości udarnościowe trzech przemysłowych wytopów stali typu 9Cr-1Mo. Wczesniejsze badania wykazały, że w stali 9Cr-1Mo starzonej w 550C przez 10 000 godzin występuje kruchość odpuszczania, a przy dłuższych czasach ekspozycji tworzy się krucha faza Lavesa (FeCr)2Mo na granicach ziaren. Powoduje to wzrost teperatury przejściowej kruchości oraz spadek energii łamania powyżej...
-
Degradacja stali 9CR-1Mo pod wpływem podwyższonej temperatury. Degradation of 9Cr-1Mo steel under the influence of elevated temperature
PublicationBadano charakterystyczne cechy degradacji mikrostruktury i właściwości mechanicznych stali 9Cr-1Mo gat. P9 ASTM SA-335 po eksploatacji w piecu rafineryjnym w temperaturze 390-500 stopni C. Wykazano, że po 30 000 godzin wydłużenie obniżyło się o około 30%. Przyczyną spadku wydłużenia były zmiany mikrostruktury związane z umocnieniem osnowy metalicznej przez chrom oraz wynikające z kruchości odpuszczania stali. Większy spadek wydłużenia...
-
Influence of H2S on degradation of 9Cr-1Mo steel in advanced stage of metal dusting process
PublicationPrzedstawiono wyniki badań stali 9Cr-1Mo w zaawansowanym stadium procesu pylenia metalu po 10 latach eksploatacji w piecu rafineryjnej instalacji platformingu CCR, przeprowadzonych w celu podjęcia decyzji o dozowaniu związków siarki do wsadu instalacji. Na podstawie długotrwałej ekspozycji próbek stali w 600C w mieszaninie wodoru i siarkowodoru wykazano, że siarka może być powodem procesów wpływających niekorzystnie na stan materiału...
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublicationThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Nondestructive Characterization of 2CR-1Mo Steel Quality Using Magnetoacousting Emission
PublicationPrzedstawiono wyniki badań własności emisji magneto-akustycznej (EMA) oraz własności magnetycznych (pętla histerezy magnetycznej, efekt Barkhausena, magnetostrykcja) dla wycinków rur stali 2Cr-1Mo o różnym stopniu degradacji. Wykazano, iż początkowy etap degradacji skutkuje w obniżeniu natężenia EMA oraz magnetostrykcja także niewielką zmianą pola koercji i nie monotoniczną zmianą natężenia efektu Barkhausena).
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublicationThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Assessment of fitness for service of Cr-Mo steel tubes in catalytic reforming charge heaters
PublicationIn this paper characteristic features of metal dusting corrosion in high temperature gas mixtures of high carbon activity in catalytic reforming units, including Continuous Catalyst Regeneration (CCR) platformer are presented. Examples of 2.25Cr-1Mo and 9Cr-1Mo steel tubes at advanced stages of metal dusting process after long-term service in charge heaters are used to prove that destructive examinations are necessary to provide...
-
Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels
PublicationThis article deals with the dissimilar joining of two different grade Cr-Mo steel (2.25Cr-1Mo: P22 and modified 9Cr-1Mo: P91) for power plant application. The dissimilar butt-welded joint was produced for conventional V groove design by using the gas tungsten arc welding (GTAW) process with the application of an ERNiCrMo-3 Ni-based super alloy filler. A microstructure characterization was performed to measure the inhomogeneity...
-
Study on Microstructure and Mechanical Properties of Laser Welded Dissimilar Joint of P91 Steel and INCOLOY 800HT Nickel Alloy
PublicationThis investigation attempts to explore the weld characteristics of a laser welded dissimilar joint of ferritic/martensitic 9Cr-1Mo-V-Nb (P91) steel and Incoloy 800HT austenitic nickel alloy. This dissimilar joint is essential in power generating nuclear and thermal plants operating at 600–650 °C. In such critical operating conditions, it is essential for a dissimilar joint to preserve its characteristics and be free from any kind...
-
Metal dusting in Platforming CCR furnaces
PublicationPrzedstawiono charakterystykę zjawiska spylania metalu w stali chromowo-molibdenowej 9Cr-1Mo eksploatowanej w piecach instalacji Platformingu CCR w środowisku odsiarczonej benzyny cięzkiej i gazu wodorowego o temperaturze 500C, przy temperaturze metalu 600C.
-
Pylenie metalu w środowisku rafineryjnym = Metal dusting in refinery environment
PublicationPrzedstawiono niektóre wyniki pierwszego etapu pracy zaprojektowanej w celu określenia mechanizmu pylenia stali 9Cr-1Mo w środowisku pieców Platformingu CCR oraz wpływu dodatku siarki w środowisku na degradację mikrostruktury stali w zaawansowanym etapie pylenia.
-
Charakterystyka korozji typu pylenie metalu w rafineryjnej instalacji platformingu CCR
PublicationW artykule przedstawiono charakterystykę procesu pylenia metalu w stali 9Cr-1Mo eksploatowanej w piecach instalacji platformingu CCR. Wykazano, że mechanizm niszczenia stali nie zależy od czasu eksploatacji i od stopnia konwersji wsadu, a krótkotrwały wzrost stężenia związków siarki we wsadzie może zwiększyć szybkość tworzenia pyłu.
-
Degradacja stali w środowiskach pieców rafineryjnych
PublicationW monografii przedstawiono mechanizmy degradacji stali o osnowie ferrytycznej, przeznaczonych do pracy w podwyższonej temperaturze w środowiskach pieców rafineryjnych, na podstawie badań rur po wieloletniej eksploatacji w piecach Rafinerii Gdańskiej SA. Badano stal węglową (gat. K18 PN-75/H-84024) i stale chromowo-molibdenowe typu 5Cr-0,5Mo i 9Cr-1Mo (gat. P5 i P9 ASTM SA-335) po eksploatacji w ciekłych frakcjach węglowodorowych...
-
Metal dusting in CCR platforming unit
PublicationPrzedstawiono mechanizm pylenia metalu w stali 9Cr-1Mo w instalacji platformingu CCR, na postawie badań rury podgrzewacza wsadu po 10 latach pracy, przy temperaturze metalu koło 600C. W badaniach wykorzystano techniki elektronowej mikroskopii skaningowej, dyfrakcji rentgenowskiej i mikroanalizy rentgenowskiej. Wykazano, że dyfuzji wegla w głąb stali toarzyszy odrdzeniowa dyfuzja pierwiastków węglikotwórczych - chromu i molibdenu....
-
Metal dusting in CCR platforming unit
PublicationPrzedstawiono mechanizm pylenia metalu w stali 9Cr-1Mo w instalacji platformingu CCR, na postawie badań rury podgrzewacza wsadu po 10 latach pracy, przy temperaturze metalu koło 600C. W badaniach wykorzystano techniki elektronowej mikroskopii skaningowej, dyfrakcji rentgenowskiej i mikroanalizy rentgenowskiej. Wykazano, że dyfuzji wegla w głąb stali toarzyszy odrdzeniowa dyfuzja pierwiastków węglikotwórczych - chromu i molibdenu....
-
Complex Steel Structures 2022
e-Learning Courses -
Complex Steel Structures (2022/23)
e-Learning Courses -
Complex Steel Structures (2023/24)
e-Learning Courses -
Deformations of the steel schell of a vertical cylindrical tank caused by underpressure
PublicationUnderpressure in a tank with a fixed roof may arise in the final stage of its construction as well as during its usage. This article presents stages of deformations of the tank shell and their development from the occurrence of the first deformation to either removal of the causes of underpressure or cracking of the steel shell.
-
Steel in Translation
Journals -
Review of titanium and steel welding methods
PublicationThe paper presents review of methods of titanium and steel welding. On basis of professional literature it was stated that titanium can be joined with steel by means of explosive welding or brazing.Joining titanium with steel by TIG welding and friction welding methods is possible with the use of copper and tantalum or vanadium interlayer.
-
STEEL CONSTRUCTION - DESIGN AND RESEARCH
Journals -
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
Journals -
The resistance of S235JR steel to cavitation erosion
PublicationThe erosion resistance of S235JR steel to flow cavitation was investigated. In order to understand an influence of steel properties and cavitation intensities on the degradation mechanisms, low-carbon S235JR steel was tested in the as-received state and after thermal treatment (annealing) under four different flow velocities. Annealing decreased steel hardness, which made S235JR steel less resistant to cavitation erosion. The performed...
-
The analysis of the influence of the corrosion protection method of selected steel elements on the steel structure life cycle costs
PublicationSteel products are widely used in the construction for the performance of essential and additional elements of engineering structures. They are characterized by high tensile strength, compression and bending, the structure homogeneity, the possibility of assembly regardless of the season and climatic conditions, ease of processing and the possibility of almost any shape. The main disadvantage of steel structures is their high susceptibility...
-
Advanced Steel Construction
Journals -
Iron and Steel Technology
Journals -
STEEL RESEARCH INTERNATIONAL
Journals -
Column base fixity in steel moment frames: Observations from instrumented buildings
PublicationThe rotational fixity of column base connections in Steel Moment Resisting Frames (SMRFs) strongly influences their seismic response. However, approaches for estimating base fixity have been validated only against laboratory test data. These approaches are examined based on strong motion recordings from four instrumented SMRF buildings in California to informbest practices for seismic response simulation. These buildings represent...
-
Recent steel structures in Poland - the selected projects
PublicationThe paper presents selected examples of recently completed steel structures in Poland. These are roofs over sport stadiums, construction of public buildings and bridges. Described examples do not exhaust the acquis in the field of steel constructions in Poland. The authors, however, may hope that the presented con-structions represents current achievements in Poland in the field of steel structures.
-
Behaviour of steel columns under impact
PublicationOne of import issues related to the idea of sustainable society is the safety of civil engineering structures. The safety and reliability of steel structures under impact loading is among a number of different aims during the design state. The aim of this paper is to present the results of investigation focused on dynamic behaviour of steel columns under impact loading. Modal and transient dynamic analyses using Finite Element...
-
Guided wave propagation in diagnostic of steel elements
PublicationThis paper is devoted to numerical investigations of elastic wave propagation in steel elements. The aim of this study is to conduct numerical analysis and experimental investigations on the propagation of elastic waves in steel elements in the context of damage detection. In particular, this paper is devoted to detection of damage occurring in the form of notch or changed thickness. This approach utilized the fact that any discontinuities...
-
Guided wave propagation in diagnostic of steel elements
PublicationThis paper is devoted to numerical investigations of elastic wave propagation in steel elements. The aim of this study is to conduct numerical analysis and experimental investigations on the propagation of elastic waves in steel elements in the context of damage detection. In particular, this paper is devoted to detection of damage occurring in the form of notch or changed thickness. This approach utilized the fact that any discontinuities...
-
The new steel-glass architecture of buildings in Japan
Publication.
-
Weldability of S500MC Steel in Underwater Conditions
PublicationWet welding with the use of covered electrodes is one of the methods of underwater welding. This method is the oldest, the most economic and the most versatile. The main difficulties during underwater wet welding are: high cooling rates of the joint, the presence of hydrogen in the arc area and formation of hard martensitic structure in the weld. These phenomena are often accompanied by porosity of welds and large number of spatters,...
-
Underwater Welding of Duplex Stainless Steel
PublicationThe present work was conducted to assess the weldability of duplex stainless steel at underwater conditions. Interest of underwater welding of this steel grade is connected with necessity of preparing welding repair technologies for subsea pipelines widely used in offshore oil and gas industry. The GMA local cavity welding method was used in the investigations. Welded beads were performed underwater at 0.5 m depth and in the air....
-
Seismic performance evaluation of steel buckling-restrained braced frames including SMA materials
PublicationThe permanent deformation of the building after seismic excitations can be determined by the Maximum Residual Interstory Drift Ratio (MR-IDR), which may be used for measuring the damage states. Low-post yield stiffness of the steel buckling-restrained braced frame (BRBF) makes this system vulnerable to large MR-IDR after a severe earthquake event. To overcome this issue, this paper investigates the seismic limit state performances...
-
Aesthetic perception of steel-glass architecture in Japan
PublicationAesthetic perception of steel-glass architecture in Japan
-
INFLUENCE OF CERAMIC COATING ON MECHANICAL PROPERTIES OF STAINLESS STEEL
PublicationCrystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublicationWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Modeling the application of steel slag in stabilizing expansive soil
PublicationThe objective of this study was to evaluate the suitability of steel slag as an additive to the engineering properties of weak clay soil. Different geotechnical laboratory tests were conducted on both stabilized and natural soils. Steel slag (SS) was added at a rate of 0, 5, 10, 15, 20, and 25% to the soil. Specific gravity, grain size analysis, Atterberg limit test, compaction test, free swell, California bearing ratio (CBR),...
-
Stability analyses of a cylindrical steel silo with corrugated sheets and columns
PublicationW artykule przedstawiono wyniki obliczeń stateczności silosów z blachy falistej ze słupami. Wykonano analizy linowe i analizy nieliniowe stosując metody elementów skończonych. W obliczeniach uwzględniono model przestrzenny powłokowy oraz uproszczony model przestrzenny z blachy ortotropowej z belkami. Wyniki numeryczne porównano z Eurokodem.
-
Joints Of Steel Sandwich Structures
PublicationSteel sandwich structures are perceived as alternatives to single-skin welded structures in the shipbuilding industry due its advantages like significant reduction of mass in relation to typical single skin structure. However, beside problems with their strength properties itself, applications in real structures requires of solving the problem of joining, both for connection sandwich to sandwich as well as sandwiches to single-shell...
-
Corrosion degradation impact on mechanical properties of structural steel
PublicationRecently, extensive research was conducted regarding the impact of corrosion degradation on the mechanical properties of structural steel. Studies show that at the material level, the microstructure is somewhat unchanged due to corrosion degradation. However, the corrosion causes pits and structural surface irregularities that consequently impact the mean stress-strain response of typical coupon specimens subjected to tensile loading....
-
Numerical modal analysis of a vertical rising steel water gate
PublicationVertical rising steel water gates are very common not only in Poland and Germany but also in other countries of the world. Their popularity is mainly attributed to their simplicity of construction, which makes their production process cheaper and faster when compared to other solutions. The aim of this paper is to conduct a numerical modal analysis to examine the eigenvalues and eigenmodes of a vertical rising steel gate. Two cases...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublicationThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
THE INFLUENCE OF POLYMER STRIPS IN REDUCTION OF A STEEL GRANDSTAND VIBRATIONS
PublicationGrandstands are types of structures commonly used during sport events or music concerts. Dynamic loads generated by crowd movement may have significant influence on human perception as well as may lead to the destruction of a structure. Lighter and more slender structural steel members are more easily excitable by spectators. If the synchronized movement is tuned with the natural frequency of the affected part of the structure,...
-
Application of guided waves in the evaluation of steel-concrete adhesive connection
PublicationThe aim of the paper is the application of guided waves in the evaluation of a condition state of adhesive connection between steel and concrete. The study concerns a push-out specimen consisting of two steel plates glued to opposite faces of a concrete cube with the use of structural adhesive. Wave propagation in the specimen without external load is investigated both experimentally and numerically. The second stage of the investigation...
-
Surface treatment of C80U steel by long CO2 laser pulses
PublicationThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
Underwater wet welding of S1300 ultra-high strength steel
PublicationMarine Structures Volume 81, January 2022, 103120 Underwater wet welding of S1300 ultra-high strength steel Author links open overlay panelJacekTomkówGrzegorzRogalski https://doi.org/10.1016/j.marstruc.2021.103120 Get rights and content Under a Creative Commons licenseopen access Highlights • Technological method of S1300 steel underwater weldability improving was proposed. • Number of cracks and hardness of welded joints was...
-
Experimental study on earthquake-induced pounding between steel structures
PublicationPounding between adjacent structures has been repeatedly observed during major earthquakes. The phenomenon may cause some local damage at the points of interactions, it may also lead to substantial destruction, permanent deformations or total collapse of colliding structures. The effects of earthquake-induced structural pounding have been studied for more than three decades now. However, most of the studies concerned masonry as...
-
Influence of Material Thickness on the Ductile Fracture of Steel Plates for Shipbuilding
PublicationIn the shipbuilding industry, the risk of brittle fractures is relatively high because some units operate in arctic or subarcticzones and use high thickness (up to 100 mm) steel plates in their structures. This risk is limited by employing certifiedmaterials with a specific impact strength, determined using the Charpy method (for a given design temperature) and byexercising control over the welding processes (technology qualification,...
-
Modal analysis of cylindrical steel tanks
PublicationCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is crucial because any failure could have serious consequences. The aim of present paper is to show the results of the first phase of investigation of seismic behaviour such structures. Modal analysis using Finite Element Method (FEM) for three models of real tanks used in Poland has...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublicationThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Temper bead welding of S420G2+M steel in water environment
PublicationThe article presents the idea of the use of Temper Bead Welding (TBW) technique to improve the weldability of high strength steel at underwater wet welding conditions. Wet welding method with the use of covered electrodes is described. This work shows results of metallographic examinations and hardness measurements of samples of S420G2+M steel with weld beads performed under water. It has been shown that Temper Bead Welding technique...
-
Temper bead welding of S460N steel in wet welding conditions
PublicationWet welding is the most common method of welding in water environment. It is most often used for repairing of underwater parts of offshore structures. However, the water as a welding environment causes an increase of susceptibility of steels to cold cracking. For underwater constructions high strength low alloy (HSLA) steel are widely used. In wet welding condition a HSLA steel is characterized by high susceptibility to cold cracking....
-
Framework for Structural Health Monitoring of Steel Bridges by Computer Vision
PublicationThe monitoring of a structural condition of steel bridges is an important issue. Good condition of infrastructure facilities ensures the safety and economic well-being of society. At the same time, due to the continuous development, rising wealth of the society and socio-economic integration of countries, the number of infrastructural objects is growing. Therefore, there is a need to introduce an easy-to-use and relatively low-cost...
-
Earthquake-Induced Pounding Between Asymmetric Steel Buildings
PublicationEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phenomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Reduction of steel chimney vibrations with a pendlum damper.
PublicationKarman vortices observed around chimneys may induce dangerous structural vi-brations at certain wind velocities. The aim of this paper is to analyse theeffectiveness of pendulum damper in vibration reduction of a steel chimney. A two degree-of-freedom system is used to model the behaviour of the struc-ture equipped with a damper. The results of the study show that the use of pendulum with tuned frequency leads to significant...
-
Application of polymer element in reduction of temporary steel grandstand vibrations
PublicationThe numerical analysis focused on reduction of vibrations of a temporary steel scaffolding grandstand has been conducted in this paper. These types of structures are regularly subjected to dynamic loads which, in conjunction with light and quite slender structural members, may induce dangerous vibrations. To increase their safety, temporary steel grandstands are usually strengthened with the diagonal stiffeners of tubular cross...
-
Journal of Iron and Steel Research
Journals -
Progress in Steel Building Structures
Journals -
CIS Iron and Steel Review
Journals -
International Journal of Steel Structures
Journals -
Earthquake-induced pounding between asymmetric steel buildings
PublicationEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
NUMERICAL MODEL OF PLASTIC DESTRUCTION OF THICK STEEL STRUCTURAL ELEMENTS
PublicationIn the shipbuilding industry, the risk of brittle fracture of the structure is limited by using certified materials with specified impact strength, determined by the Charpy method (for a given design temperature) and by supervising the welding processes (technology qualification, production supervision, non-destructive testing). For off-shore constructions, classical shipbuilding requirements may not be sufficient. Therefore, the...
-
Numerical analysis of a temporary steel grandstand
PublicationThe purpose of this paper is to present the results of the numerical analysis focused on the response of the temporary steel scaffolding grandstand subjected to human-induced vibrations due to jumping. Shell as well as beam elements have been used in the numerical model. Its first stage has involved conducting modal analysis in order to determine the modes of free vibrations and the corresponding natural frequencies for the empty...
-
Weldability of high strength steel in underwater environment
PublicationThe article describes the problems with weldability of high-strength steels in the aquatic environment. The tendency of steel S355J2G3 and S500M to form cold cracks when welded in wet welding conditions has been experimentally evaluated. It was found that the tested steels have a high propensity to cracking. An experiment has been proposed and tested to evaluate the usefulness of the tempering bead technique as a method of improving...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublicationThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy
PublicationIn this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
-
Stresses in the zone of process openings in the shell of a vertical cylindrical steel tank
PublicationW dolnej części płaszcza zbiornika walcowego na ciecze konieczne jest wykonanie różnego rodzaju otworów technologicznych. Artykuł poświęcony jest analizie stanu naprężeń w strefie wzmocnień wykonywanych w sąsiedztwie otworów na rurociągi oraz na włazy wyczystkowe w płaszczu zbiornika. Ponieważ charakter zmian naprężeń, a więc i wzmocnień w strefie obu rodzajów otworów jest różny dlatego artykuł podzielony jest na dwie części, z...
-
Shaking table experimental study on models of steel buildings with different types of joints
PublicationThe aim of this paper is to study the response of models of steel buildings with destroyed and non-destroyed joints. The study was conducted experimentally using the shaking table tests. Two steel models were considered. Several types of joints were taken into account: totally destroyed joints, partially destroyed joints, welded joints and joints stiffened with additional metal. Six ground motions were taken into account. The acceleration...
-
Launching of steel bridge girder. Application of nonlinear shell models
PublicationThe paper describes the final technology of launching the steel bridge superstructure. The original technology failed in the first construction stage. Local damage of steel webs caused by plastic buckling stopped the procedure. In the effect of damage a new consulting team was employed to solve the problem and redesign a technology of constructing. The key element of the new solution was developed with great help of non-linear...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Modal Analysis of a Steel Radial Gate Exposed to Different Water Levels
PublicationWith the increase in water retention needs and planned river regulation, it might be important to investigate the dynamic resistance of vulnerable elements of hydroelectric power plants, including steel water locks. The most frequent dynamic loads affecting hydroengineering structures in Poland include vibrations caused by heavy road and railway traffic, piling works and mining tremors. More destructive dynamic loads, including...
-
Corrosivity of environment and the current state of the steel elements at the former Auschwitz concentration camp
PublicationThe objective of this study was to assess corrosivity of the atmospheric environment in the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp, and to identify the protective properties of existing corrosion products in order to estimate the actual corrosion rate of original steel elements located there. The current atmospheric corrosivity of the former Auschwitz camp, specified during one year of exposure...
-
Assessment of crack resistance of S355J2+N steel according to SEP 1390 standard
PublicationThe aim of the study was to evaluate the weldability of S355J2+N steel by bending test according to SEP 1390. In the specimen from S355J2+N steel 3 external cracks were found, 1 of which were stopped in the fusion line and 2 in heat affected zone. Results of bending test for investigated grade of steel are positive.
-
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
PublicationIn the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...
-
Cold Cracking Of Underwater Wet Welded S355G10+N High Strength Steel
PublicationWater as the welding environment determines some essential problems influencing steel weldability. Underwater welding of high strength steel joints causes increase susceptibility to cold cracking, which is an effect of much faster heat transfer from the weld area and presence of diffusible hydrogen causing increased metal fragility. The paper evaluates the susceptibility to cold cracking of the high strength S355G10+N steel used,...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublicationThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublicationIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
Corrosion and Cavitation Resistances of Low Alloy Steel After Frictional-Mechanical Treatment
PublicationPaper presents the results of the studies of wear, corrosion and cavitation resistances of the S355J2 low alloy medium carbon steel subjected to surface modification by friction-mechanical treatment, as tested in sea water simulated solution. To evaluate the effect of the surface treatment, the comparative studies of the corrosive properties of the steel before and after treatment have been considered. The treatment due to a severe...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublicationThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
state aid for steel sector in the EU
Open Research DataThe dataset encompassed a choice of most important UE and Polish legal acts, a list of selected Polish and foreign bibliography and a list of important individual decisions issued on the topic of state aid for steel industry in the UE. The significance of this topic is undoubted, as the steel industry is one of the most important UE production branches....
-
Austenitic stainless steel sensitization
Open Research DataHigh-alloy steels, thanks to their composition and content of appropriate alloying additives, are characterized by increased resistance to many corrosive environments. However, this is due to the increased sensitivity of the described construction materials to specific environmental conditions during their use. An example may be the increased susceptibility...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublicationSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
Application of guided wave propagation in diagnostics of steel bridge components
PublicationEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
The Effectiveness of Polymer Damper in Damage Reduction of Temporary Steel Grandstand
PublicationA large number of accidents involving damage of temporary grandstands during different types of events were observed in the past. The aim of the paper is to analyse numerically the effectiveness of a polymer damper in damage reduction of a temporary steel scaffolding grandstand exposed to dynamic load due to jumping. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Resistance to cold cracking of steel joints of P460NL1 steel
PublicationPrzedstawiono wyniki badań odporności na zimne pękanie złączy spawanych ze stali przeznaczonej do pracy pod ciśnieniem. Badano równoczesny wpływ zawartości wodoru dyfundującego i energii liniowej na naprężenie krytyczne w próbie implant dla złączy spawanych elektrodami otulonymi i drutem proszkowym w osłonie gazów ochronnych. Stwierdzono wpływ energii liniowej jak i zawartości wodoru dyfundującego na odporność na zimne pękanie...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublicationThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublicationIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
NUMERICAL ANALYSIS OF RUBBER BUMPERS INFLUENCE ON THE COLLIDING STEEL STRUCTURES
PublicationProblem of collisions of neighbouring structures is one of the important issues related to the safety of civil engineering structures. The safety and reliability of steel structures under impact loading is among a number of different aims during the design state. The aim of this paper is to present the results of numerical investigation of dynamic behavior of closely-separated steel structures under seismic excitation. Modal and transient...
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublicationBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublicationThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublicationThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Fatigue fracture morphology of AISI H13 steel obtained by additive manufacturing
PublicationThe paper focuses on researching the effect of fatigue loading on metallic structure, lifetime, and fracture surface topographies in AISI H13 steel specimens obtained by selective laser melting (SLM). The topography of the fracture surfaces was measured over their entire area, according to the entire total area method, with an optical three-dimensional surface measurement system. The fatigue results of the SLM 3D printed steel...
-
Weldability of Underwater Wet-Welded HSLA Steel: Effects of Electrode Hydrophobic Coatings
PublicationThe paper presents the effects of waterproof coatings use to cover electrodes on the weldability of high-strength, low-alloy (HSLA) steel in water. With the aim of improving the weldability of S460N HSLA steel in water, modifications of welding filler material were chosen. The surfaces of electrodes were covered by different hydrophobic substances. The aim of the controlled thermal severity (CTS) test was to check the influence...