Filters
total: 8274
filtered: 4687
-
Catalog
- Publications 4687 available results
- Journals 156 available results
- Conferences 35 available results
- People 242 available results
- Projects 11 available results
- Laboratories 2 available results
- e-Learning Courses 308 available results
- Events 9 available results
- Open Research Data 2824 available results
Chosen catalog filters
displaying 1000 best results Help
Search results for: DESIGN CENTERING
-
Rapid antenna design optimization using shape-preserving response prediction
PublicationAn approach to rapid optimization of antennas using the shape-preserving response-prediction (SPRP) technique and coarsediscretization electromagnetic (EM) simulations (as a low-fidelity model) is presented. SPRP allows us to estimate the response of the high-fidelity EM antenna model, e.g., its reflection coefficient versus frequency, using the properly selected set of so-called characteristic points of the low-fidelity model...
-
Hierarchical dynamic hybrid models for aided design of ship power subsystems.
PublicationRozważa się wielopoziomowe modele systemu energetycznego statku. Elementy systemu są modelowane z użyciem ciągłych zmiennych stanu i uwzględnieniem zerowego związku przyczynowo-skutkowego. Poziom pierwszy opisuje wzajemne związki modeli zerowego poziomu, poziom drugi reprezentuje powiązania modeli pierwszego poziomu itd. W ten sposób opisuje się modele elementów zespołów i podsystemów. Każdy z modeli może być hybrydowym modelem...
-
Design of synchronous generator voltage regulator based on h control theory
PublicationThe power system is highly nonlinear system, which dynamics depends on system network configuration, system loading…etc. To overcome the above mentioned difficulties and to fulfill the performance requirements the different control methods are considered and tested for application to generating control unit. Application of the H optimization method to automatic voltage regulator is studied in this paper. Simulation results have...
-
Design and measurement of gyrator and isolator using ferrite coupled microstrip lines
PublicationW publikacji przeprowadzono badania struktur żyratora i izolatora zrealizowanych w technice sprzężonych ferrytowych linii mikropaskowych. Po raz pierwszy zaprezentowano wyniki pomiaru zrealizowanych struktur tego rodzaju. Uzyskane wyniki potwierdzają przewidziany uprzednio efekt zmian kierunków działania opisywanych elementów ze zmianą częstotliwości.
-
Centralized and Distributed Structures of Intelligent Systems for Aided Design of Ship Automation
PublicationA design process and accepted solutions made during this process, often base on non-formalized knowledge, obtained from designer (expert) intuition and practice. There are no formalized rules assuring the correctness of design solutions. The analysis of design process of ship automation, including ship power system, shows that this process can be supported by application of the artificial intelligence elements. The article presents...
-
Sensitivity analysis in design process of sandwich U-shaped composite footbridge
PublicationThe structure of the sandwich composite footbridge of a 14 metre span length and U-shaped cross-section was analysed. Sensitivity analysis was performed to support the design process of this innovative object. Linear discrete sensitivity analysis was performed by means of finite element method. The influence of vari-ation of several design variables i.e. thicknesses of inner and outer laminates on the mid-span deflection, as-sumed...
-
Podejście środowiskowe w dydaktyce projektowania Sustainable approach in teaching of design
PublicationThe aim of the paper is to assess the inclusion of academic teaching design to the process of sustainable development and proposals for an integrated approach in training architects. The article presents an original interpretation of environmental design in the field of architecture and urban planning. The significance of the environmental perspective is presented in the context of growing spatial and social fragmentation. The...
-
DESIGN THINKING ORIENTED METHODOLOGY IN GROUP PROJECT AS A STEP IN THE CDIO APPROACH
PublicationRecently much scientific research and industrial work is conducted in multidisciplinary teams, where cooperation between specialists from different areas of expertise is required in order to successfully address the challenging goals. Moreover, in start-up small companies the lack of supporting departments calls for additional multidisciplinary, economic and networking skills known as T-shaped personality. Recognizing these shortcomings...
-
From Creative Thinking Techniques to Innovative Design Solutions - The Educators' Perspective
PublicationThe article presents a structure and basic tasks of a new original academic course, which was inaugurated in 2015 at the Faculty of Architecture in Gdańsk University of Technology and organized for the first year students of Spatial Planning.The title of the course was ‘Garden Cities and the Gardens in the Cities. A Course with Elements of Training Creativity’. The aim of the course was to encourage the participants to develop...
-
The basics of design and experimental tests of the commutation unit of a hydraulic satellite motor
Publicationhe article presents an analytical method to design the commutation unit in a hydraulic satellite motor. It is shown that the size of the holes feeding the working chambers and their location on the plates closing those chambers depends on the geometrical dimensions of the working mechanism. The overlap in the commutation unit depends on the rotational speed range. It is demonstrated that the geometrical dimensions of the commutation...
-
Structural Health Monitoring of Composite Shell Footbridge for Its Design Validation
PublicationThe paper presents the structural health monitoring system of the composite bridge for pedestrians and cyclists. The footbridge was designed and manufactured within the FOBRIDGE project. It is the first bridge in the world, which is classified as a consistent single element structural girder, made of sandwich shells, entirely produced in a single cycle. The developed structural health monitoring system, supported design process,...
-
Substrate-integrated waveguide (SIW) filter design using space mapping
PublicationIn this paper, we present a fast technique for an automated design of microwave filters in substrate integrated wave (SIW) technology. The proposed methodology combines the space mapping technique with a cost function defined using the location of complex zeros and poles of filter’s transfer and reflection function and uses a rectangular waveguide as a surrogate model. The effectiveness of the proposed technique is presented with...
-
Cost-efficient design optimization of compact patch antennas with improved bandwidth
PublicationIn this letter, a surrogate-assisted optimization procedure for fast design of compact patch antennas with enhanced bandwidth is presented. The procedure aims at addressing a fundamental challenge of the design of antenna structures with complex topologies, which is simultaneous adjustment of numerous geometry parameters. The latter is necessary in order to find a truly optimum design and cannot be executed-at the level of high-fidelity...
-
The analytical design method of railway route’s main directions intersection area
PublicationThe paper presents a design method related to railway track sections situated in a bend. In the method advantage is taken of an analytical form of description by using appropriate mathematical formulae. This may becomeparticularly usefulwhen the investigations are based on the data obtained from mobile satellite measurements. In the paper attention is concentrated on an universal approach creating an opportunity to diversify the...
-
Smart Cities System Design Method Based on Case Based Reasoning
PublicationThe objective of this paper is to present the results of research carried out to develop a design method for Smart Cities systems. The method is based on the analysis of design cases of Smart Cities systems in cities, the selection of the city appropriate to the requirements for implementation and application. The Case Based Reasoning method was used to develop the proposed design methodology, along with mechanisms of the conversion...
-
Interactive Prototypes in Teaching User-Centred Design and Business Process Modelling
PublicationThis publication describes experiences gathered during the use of interactive prototyping in two areas: design of user interfaces for a touch screen information kiosk and interactive prototyping of business processes. Prototyping is promoted here as a technique useful for both visualizing design concepts and for stimulating communication within relevant teams. Developing interactive prototypes of use interfaces is discussed here...
-
Multi-fidelity robust aerodynamic design optimization under mixed uncertainty
PublicationThe objective of this paper is to present a robust optimization algorithm for computationally efficient airfoil design under mixed (inherent and epistemic) uncertainty using a multi-fidelity approach. This algorithm exploits stochastic expansions derived from the Non-Intrusive Polynomial Chaos (NIPC) technique to create surrogate models utilized in the optimization process. A combined NIPC expansion approach is used, where both...
-
Rapid multi-objective simulation-driven design of compact microwave circuits
PublicationA methodology for rapid multi-objective design of compact microwave circuits is proposed. Our approach exploits point-by-point Pareto set identification using surrogate-based optimization techniques, auxiliary equivalent circuit models, and space mapping as the major model correction method. The proposed technique is illustrated and validated through the design of a compact rat-race coupler. A set of ten designs being trade-offs...
-
A new approach to design of weather disruption-tolerant wireless mesh networks
PublicationWireless Mesh Networks, offering transmission rates of 1–10 Gb/s per a millimeter-wave link (utilizing the 71–86 GHz band) seem to be a promising alternative to fiber optic backbone metropolitan area networks because of significantly lower costs of deployment and maintenance. However, despite providing high transmission rates in good weather conditions, high-frequency wireless links are very susceptible to weather disruptions....
-
Electromagnetic interference frequencies prediction model of flyback converter for snubber design
PublicationSnubber design for flyback converters usually requires experimental prototype measurements or simulation based on accurate and complex models. In this study simplified circuit modelling of a flyback converter has been described to dimension snubbers in early stage of design process. Simulation based prediction of the transistor and diode ringing frequencies has been validated by measurements in a prototype setup. In that way obtained...
-
Design of control algorithms for mobile robots in an environment with static and dynamic obstacles
PublicationThis article proposes the construction of autonomous mobile robots and designing of obstacle avoidance algorithms for them. Nowadays, mobile robots are gaining more and more popularity on the customer as well as industrial market, for example as automatic vacuum cleaners or lawnmowers. Obstacle avoidance algorithms play an important role in performance of this types of robots. The proposed algorithms were designed for builds with...
-
Implementation of daylight design strategies in urban planning - barriers to application in Poland
PublicationThis paper reflects on studies done in the area of daylight design methods with regard to principles that can be applied in architecture and urban planning strategies. The paper addresses barriers to the application of new daylight design methods in urban planning, and in particular discusses current Polish building regulations in the context of daylight design. The results of the pilot study carried out among 82 participants show...
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublicationThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...
-
A structure and simulation-driven design of compact CPW-fed UWB antenna
PublicationIn this letter, a structure of a miniaturized ultra-wideband CPW-fed antenna and its design proce-dure are presented. The antenna is a modified version of the design previously proposed in the literature, with additional degrees of freedom introduced in order to improve the structure flexibility. The small size is achieved by executing a rigorous optimization procedure that consists of two stages: (i) smart random search carried...
-
Fast simulation-driven design optimization of UWB band-notch antennas
PublicationIn this letter, a simple yet reliable and automated methodology for rapid design optimization of ultra-wideband (UWB) band-notch antennas is presented. Our approach is a two-stage procedure with the first stage focused on the design of the antenna itself, and the secondstage aiming at identification of the appropriate dimensions of the resonator with the purpose of allocating the band-notch in the desired frequency range. For the...
-
Design and implementation principles of FIReWORK ONLINE - the VHDL autogenerator for hardware structures
PublicationThe paper presents an aspects of remote autogeneration of hardware structures. The solution is an online application, that is running on the server side and allows to design a particular filters and other selected hardware and generate its structure in the form of VHDL, dedicated to FPGA design environments. The paper also addresses the problem of parameterization of algorithms used to generate the hardware structures and current...
-
APPLICATION OF VORTEX FLOW MODEL IN PROPELLER-STATOR SYSTEM DESIGN AND ANALYSIS
PublicationThe paper covers basics of the vortex model used for propeller-stator systems. The outline of the design algorithm is given and the results of its application are shown. The designed propeller-stator system was the subject of model tests run at the CTO model basin and cavitation tunnel. Stator’s influence on the delivered power required by the propeller and its revolution rate has been examined by conducting self-propulsion...
-
Decision support system for design of long distance heat transportation system
PublicationDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). The paper proposes a Decision Support System (DSS) for optimized selection of design and operating parameters of a long distance Heat Transportation System (HTS). The method allows for evaluation of feasibility and effectiveness...
-
Pantographic metamaterials: an example of mathematically driven design and of its technological challenges
PublicationIn this paper, we account for the research efforts that have been started, for some among us, already since 2003, and aimed to the design of a class of exotic architectured, optimized (meta) materials. At the first stage of these efforts, as it often happens, the research was based on the results of mathematical investigations. The problem to be solved was stated as follows: determine the material (micro)structure governed by those...
-
RNS/TCS CONVERTER DESIGN USING HIGH-LEVEL SYNTHESIS IN FPGA
PublicationAn experimental high-level synthesis (HLS) of the residue number system (RNS) to two’s-complement system (TCS) converter in the Vivado Xilinx FPGA environment is shown. The assumed approach makes use of the Chinese Remainder Theorem I (CRT I). The HLS simplifies and accelerates the design and implementation process, moreover the HLS synthesized architecture requires less hardware by about 20% but the operational frequency is smaller...
-
Moving Towards Competence in Teaching Architecture: The Relationship of Research and Design in Academia
PublicationArchitecture is truly a profession of public trust requiring special care at all stages in academic education. European educational reforms initiated by the 1999 Bologna Process affected architecture education, and shifted the role of research. The number of doctoral programs increased, so the involvement of PhD students in teaching also expanded. This study aims to identify how these changes affect quality in architecture education....
-
How to Design Affect-aware Educational Systems – the AFFINT Process Approach
PublicationComputer systems, that support learning processes, can adapt to the needs and states of a learner. The adaptation might directly address the knowledge deficits and most tutoring systems apply an adaptable learning path of that kind. Apart from a preliminary knowledge state, there are more factors, that influence education effectiveness and among those there are fluctuating emotional states. The tutoring systems may recognize or...
-
Accurate simulation-driven modeling and design optimization of compact microwave structures
PublicationCost efficient design optimization of microwave structures requires availability of fast yet reliable replacement models so that multiple evaluations of the structure at hand can be executed in reasonable timeframe. Direct utilization of full-wave electromagnetic (EM) simulations is often prohibitive. On the other hand, accurate data-driven modeling normally requires a very large number of training points and it is virtually infeasible...
-
Cost-efficient simulation-driven design of compact impedance matching transformers
PublicationIn this paper, an algorithmic framework for cost-efficient design optimization of miniaturized impedance matching transformers has been presented. Our approach exploits a bottom-up design that involves translating the overall design specifications for the circuit at hand to its elementary building blocks (here, compact microstrip resonant cells, CMRCs), as well as fast surrogate-assisted optimization of the cells followed by simulation-based...
-
On Reduced-Cost Design-Oriented Constrained Surrogate Modeling of Antenna Structures
PublicationDesign of contemporary antenna structures heavily relies on full-wave electromagnetic (EM) simulation models. Such models are essential to ensure reliability of evaluating antenna characteristics, yet, they are computationally expensive and therefore unsuitable for handling tasks that require multiple analyses, e.g., parametric optimization. The cost issue can be alleviated by using fast surrogate models. Conventional data-driven...
-
Experience Based Decisional DNA (DDNA) to Support Sustainable Product Design
PublicationThis paper presents the idea of providing engineering design knowledge to designers working on sustainable product design and development process. The new product development process often requires significant amount of design knowledge which can be saved and recalled by designers during the design process. This knowledge is very important for successful sustainable product development as it can include material selection, product...
-
Analysis and design improvement of high class roads’ arched sections in Poland
PublicationAlthough Polish road network standards, in particular higher classes of roads are improving dynamically the number of fatalities on the network is still higher that EU’s average. Ensuring road safety and high maintaining standards is a complex issue and one that poses a major challenge for all road authorities. Road accidents at high speed roads characterize specially serious material and social consequences, thus research into...
-
Certified Integrated Circuit Design Lab - obtaining the certificate and the benefits of having it
PublicationThis paper describes the process of establishing and maintaining a certified integrated circuit design lab. The advantages of having a certification for the lab are presented, and also how to obtain the certificate based on the example of Cadence Certified Lab at Gdansk University of Technology, Poland. Various integrated circuits designed at the lab are also briefly shown.
-
Design of a Patch Power Divider with Simple Structure and Ultra-Broadband Harmonics Suppression
PublicationThis paper introduces a simple H-shaped patch Wilkinson power divider (WPD), which provides ultra wide harmonics suppression band. The presented WPD designed at 1.8 GHz, and exhibits good performance at the operating bandwidth. In the proposed divider structure, two simple patch low-pass filters (LPFs) are employed at each branch, and three open ended stubs are added at each port. The proposed divider, implemented using the aforementioned...
-
Contemporary Architectural Design in the Context of Historic Remains: The Case of the Old City of Gdańsk
PublicationThis article presents several examples of modern developments designed to preserve and coexist with fragments of historic brick buildings. These building projects each faced a similar task; to save and display the historical urban fabric, but they differed significantly in how they chose to achieve that goal. Not all of the projects presented in this study meet the requirements of the Venice Charter equally well. In this field,...
-
Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters
PublicationBuffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more...
-
Computationally Efficient Surrogate-Assisted Design of Pyramidal-Shaped 3D Reflectarray Antennas
PublicationReflectarrays (RAs) have been attracting considerable interest in the recent years due to their appealing features, in particular, a possibility of realizing pencil-beam radiation patterns, as in the phased arrays, but without the necessity of incorporating the feeding networks. These characteristics make them attractive solutions, among others, for satellite communications or mobile radar antennas. Notwithstanding, available microstrip...
-
Global Design Optimization of Microwave Circuits Using Response Feature Inverse Surrogates
PublicationModern microwave design has become heavily reliant on full-wave electromagnetic (EM) simulation tools, which are necessary for accurate evaluation of microwave components. Consequently, it is also indispensable for their development, especially the adjustment of geometry parameters, oriented towards performance improvement. However, EM-driven optimization procedures incur considerable computational expenses, which may become impractical...
-
Multi-Criterial Design of Antennas with Tolerance Analysis Using Response-Feature Predictors
PublicationImperfect manufacturing is one of the factors affecting the performance of antenna systems. It is particularly important when design specifications are strict and leave a minimum leeway for a degradation caused by geometry or material parameter deviations from their nominal values. At the same time, conventional antenna design procedures routinely neglect to take the fabrication tolerances into account, which is mainly a result...
-
Design aspects of a low-cost prosthetic arm for people with severe movement disabilities
PublicationIn this paper the main aspects of mechanical design behind the low-cost prosthetic arm are presented. The fundamentals of a proper design has been defined to obtain functional 3D printed 5 degree of freedom (DOF) prosthesis. The designed prosthetic arm is a part of the hybrid interface with eye tracking movement control. The main focus was to create affordable but usable prosthesis which corresponds in size and weights to the human...
-
Design Evolution of the Ultrasonic Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThe development process and experimental investigation of the multicell piezoelectric motor is presented in this paper. The proposed design consists of three individual cells integrated into the stator, double rotor, and a preload system. Those elements are combined into a symmetrical structure of the motor. The two new prototypes have been designed, simulated and tested. Finite element numerical analysis is carried out to obtain...
-
Surrogate-Assisted Design of Checkerboard Metasurface for Broadband Radar Cross-Section Reduction
PublicationMetasurfaces have been extensively exploited in stealth applications to reduce radar cross section (RCS). They rely on the manipulation of backward scattering of electromagnetic (EM) waves into various oblique angles. However, arbitrary control of the scattering properties poses a significant challenge as a design task. Yet it is a principal requirement for making RCS reduction possible. This article introduces a surrogate-based...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublicationThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Improved Design Closure of Compact Microwave Circuits by Means of Performance Requirement Adaptation
PublicationNumerical optimization procedures have been widely used in the design of microwave components and systems. Most often, optimization algorithms are applied at the later stages of the design process to tune the geometry and/or material parameter values. To ensure sufficient accuracy, parameter adjustment is realized at the level of full-wave electromagnetic (EM) analysis, which creates perhaps the most important bottleneck due to...
-
Application of probabilistic tools to extend load test design of bridges prior to opening
PublicationLoad tests of bridges are widely performed in a large number of countries. Deterministic comparison of measurement results to the theoretical, FEM (finite element method)-based outcomes with possible further calibration is mostly applied. Sometimes, the data collected in the tests are also used to calibrate the reliability factors of bridge structures or their components. This work proposes to complement the stage of the load test...