Filters
total: 2100
filtered: 2022
displaying 1000 best results Help
Search results for: EFFCIENCY
-
Hybrid geothermal-fossil power cycle analysis in a Polish setting with a focus on off-design performance and CO2 emissions reductions
PublicationGrowing demand for electricity due to economic development contributes to increased greenhouse gas production, especially CO2. However, emissions can be limited by enhancing the efficiency of primary energy conversion, such as integrating geothermal energy into coal-fired power plants. Therefore, this paper proposes replacing conventional feed-water heaters with geothermal preheaters to create a hybridized system. This study was...
-
Advanced Scalar-valued Intensity Measures for Residual Drift Prediction of SMRFs with Fluid Viscous Dampers
PublicationMaximum Residual Inter-story Drift Ratio (RIDRmax) plays an important role to specify the state of a structure after severe earthquake and the possibility of repairing the structure. Therefore, it is necessary to predict the RIDRmax of Steel Moment-Resisting Frames (SMRFs) with high reliability by employing powerful Intensity Measures (IMs). This study investigates the efficiency and sufficiency of scalar-valued IMs for predicting...
-
Electrochemical, theoretical and surface physicochemical studies of the alkaline copper corrosion inhibition by newly synthesized molecular complexes of benzenediamine and tetraamine with π acceptor
PublicationTwo charge transfer complexes, namely [(BDAH)+(PA−)] CT1 [(BTAH)2+(PA−)2] and CT2 (BDAH = 1,2-benzenediamine, BTAH = 1,2,4,5-benzenetetramine, and PA− = 2,4,6-trinitrophenolate), were synthesized and fully characterized using various spectroscopic techniques. CT1 and CT2 were tested as inhibitors to effectively control the uniform and anodic corrosion processes of copper in an alkaline electrolyte (1.0 M KOH) using various electrochemical...
-
Process Control of Biogas Purification Using Electronic Nose
PublicationNowadays, biogas produced from landfills and wastewater treatment plants or lignocellulosic biomass is important sustainable and affordable source of energy. Impurities from biogas stream can cause a serious odor problem, especially for residents of areas immediately adjacent to production plants. Therefore, biogas pre-treatment is necessary to protect engines that convert biogas into energy and in order to increase the specific...
-
Towards Carbon Neutral Settlements. The Importance of Early-Stage Urban and Energetic Optimizations
PublicationThe aim of the research was to verify the essence of interdisciplinary energy optimizations in earlystage urban design process. A further aim was to the find most optimal design variant and scenario in terms of urban energy efficiency for the future development in Nowy Port, located in Gdansk, Poland - a place requiring complex revitalization. The research combined qualitative and quantitative approaches; an urban design layer...
-
Expedited Design Closure of Antenna Input Characteristics by Trust Region Gradient Search and Principal Component Analysis
PublicationOptimization-based parameter tuning has become an inherent part of contemporary antenna design process. For the sake of reliability, it is typically conducted at the level of full-wave electromagnetic (EM) simulation models. This may incur considerable computational expenses depending on the cost of an individual EM analysis, the number of adjustable variables, the type of task (local, global, single-/multi-objective optimization),...
-
Analiza skuteczności wybranych strategii kontrariańskich na warszawskiej GPW w latach 2014–2018
PublicationCapital multiplication is the main goal of investors and for many years they have been looking for methods and strategies that would enable them to achieve it to the greatest possible extent. Due to the fact that the expectations and characteristics of investors, including those concerning the investment period, are diverse, multiple strategies have emerged. One of such strategies, mainly long-term in nature, is the so-called...
-
Introduction to MIP synthesis, characteristics and analytical application
PublicationOne of the trends in analytical chemistry is associated with designing and developing new types of sample preparation techniques, which might significantly increase the efficiency and selectivity of the analytes isolation or/and preconcentration process. One of the most widely employed solutions are selective sorption materials, defined as molecularly imprinted polymers (MIPs), as well as the sorbents with the molecular fingerprint....
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublicationDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
-
Combination of air-dispersion cathode with sacrificial iron anode generating Fe2+Fe3+2O4 nanostructures to degrade paracetamol under ultrasonic irradiation
PublicationIn the present study, ultrasound (US) was coupled with an electrochemical process (ECP) consisting of a novel cathode of carbon cloth (CC)-carbon black (CB) as the nano-composite air-dispersion cathode (NADC) for the degradation of paracetamol (APAP) in an aquatic medium. The NADC favored in situ production of H2O2 by the cathodic reduction. The implementation of iron sacrificial anode instead of dimensionally stable anodes resulted...
-
Improved Performance of 1-Ethyl-3-Methylimidazolium Tetrafluoroborate at Steel/HCl Interface by Iodide Ions
PublicationThe corrosion and corrosion inhibition of St37 steel in 0.1 M HCl solution by 1-ethyl-3-methylimidazolium tetrafluoroborate (EMITFB) and the effect of addition of KI on the inhibitive performance of EMITFB have been examined by electrochemical [electrochemical impedance spectroscopy, potentiodynamic polarization, and dynamic electrochemical impedance spectroscopy (DEIS)] and surface examination [scanning electron microscope (SEM)...
-
Minimizing Distribution and Data Loading Overheads in Parallel Training of DNN Acoustic Models with Frequent Parameter Averaging
PublicationIn the paper we investigate the performance of parallel deep neural network training with parameter averaging for acoustic modeling in Kaldi, a popular automatic speech recognition toolkit. We describe experiments based on training a recurrent neural network with 4 layers of 800 LSTM hidden states on a 100-hour corpora of annotated Polish speech data. We propose a MPI-based modification of the training program which minimizes the...
-
Flexible dye-sensitized solar cells based on Ti/TiO2 nanotubes photoanode and Pt-free and TCO-free counter electrode system
PublicationFlexible dye-sensitized solar cells (DSSCs) are getting more attention compared to standard glass covered DSSCs due to their unique commercial applications (e.g. tents or sail surfaces) and the possibility of rolling up into a small, portable device. In this work, titania nanotubes (TiO2 NT) modified with titania nanoparticles (TiO2 NP) were photoelectrochemically characterized as an anode for flexible dye-sensitized solar cells....
-
Novel microstrip low-pass filters with fractal defected ground structures
PublicationIn this study, three microstrip low-pass filters (LPFs) containing fractal-shaped defected ground structures have been designed and manufactured. To improve the performance of microstrip LPF, cascades of inductively coupled fractal resonators have been applied. Simultaneously, to achieve relatively constant microstrip impedance resulting in essentially low reflection losses, a modification of the strip geometry has been introduced....
-
Communication Model Order Reduction in Hybrid Methods Involving Generalized Impedance Matrix
PublicationA novel strategy for the efficient analysis of frequency-domain scattering electromagnetic problems in open and closed domains is presented. A fully automatic model-order reduction technique, called the enhanced reduced-basis method, is applied to increase the efficiency of the hybrid approach, which combines the finite-element and mode-matching methods. Numerical tests show that the proposed algorithm yields reliable and highly...
-
NEW CONCEPT OF HYBRID PROPULSION WITH HYDROSTATIC GEAR FOR INLAND WATER TRANSPORT
PublicationThe article presents the development of author’s concept of a diesel/hydraulic propulsion system for inland watercraft. Due to specific nature of vessel navigation on rivers, classical propulsion systems with shaft lines can be effectively replaced by systems with hydraulic power transmission. A solution is also presented of a hybrid design with extra electric port having the form of a pumping system driven from a battery of accumulators....
-
Time domain model of the resonance-based electromagnetic pulses emission system
PublicationIn the literature, the emission properties of the electromagnetic field pulse systems based on high voltage antennas (HVR) have been widely described. In order to increase the emission efficiency by extending duration and increasing amplitude of the impulse it is possible to use a resonance system tuned to the parameters of the signal shaped in the pulse forming circuit. The synthesis of a time-domain simulation model of a complex...
-
Method of sacrificial anode dual transistor-driving in stray current field
PublicationIn order to control a magnesium anode in a stray current interference field, a dual transistor driving system has been proposed. It consisted of a combination of PNP and NPN transistors. Dual transistor driven system and direct anode to cathode connection were electrochemically tested in 3% NaCl solution. The dual transistor driven system increased the anode efficiency and reduced hydrogen evolution and the risk of embrittlement....
-
Community Road Safety Strategies in the Context of Sustainable Mobility
PublicationThe paper presents an overview on the road safety strategies and action plans implemented in the framework of the “SOL - Save our lives: Comprehensive road safety strategy for Central Europe” project. It contains summarization of learned knowledge regarding the efficiency of measures applied and highlights examples of good practices. The purpose of the paper is to provide recommendations for effective and successful planning, formulation...
-
Multi-Option Model of Railway Traffic Organization Including the Energy Recuperation
PublicationThe article presents the issue of organization of railway traffic within the station, taking into account energy recuperation. We identified a number of factors which affect the energy efficiency of recuperation, including the issue of transfer of energy technology between a few vehicles. We presented some aspects of the decision problem of graphic train timetable construction with regard to recuperation. As an indicator of quality...
-
Ocena przekształceń piętrowego, ceglanego domu z dachem półpłaskim z przełomu XIX–XX wieku pod wpływem termomodernizacji na przykładzie gminy Puck, woj. pomorskie.
PublicationCeglane budynki mieszkalne z przełomu XIX i XX wieku, które stanowiły charakterystyczny element krajobrazu wsi pomorskiej, obecnie powszechnie poddawane są modernizacji w celu poprawy warunków cieplnych. Przedmiotem badania jest stan zachowania najmłodszego, historycznego typu domuw zagrodzie chłopskiej na Kaszubach – piętrowego, ceglanego domu z dachem półpłaskim. Badanie przeprowadzono na obszarze gminy Puck. Zidentyfikowano...
-
Wpływ ścieków przemysłowych na energochłonność i efektywność procesów technologicznych w komunalnej oczyszczalni ścieków
PublicationW artykule skupiono się na przedstawieniu wpływu jakości i ilości ścieków przemysłowych wprowadzanych do sieci kanalizacyjnej PEWIK GDYNIA Sp. z o. o. na stabilność procesów technologicznych. Określono również wpływ ścieków przemysłowych na energochłonność i efektywność oraz na wzrost kosztów oczyszczania ścieków komunalnych w Grupowej Oczyszczalni Ścieków „Dębogórze” w latach 2012-2015.
-
Some Optimization Methods for Simulations in Volunteer and Grid Systems
PublicationIn this chapter, some optimization methods have been presented for improving performance of simulations in the volunteer and grid computing system called Comcute. Some issues related to the cloud computing can be solved by presented approaches as well as the Comcute platform can be used to simulate execution of expensive and energy consuming long-term tasks in the cloud environment. In particular, evolutionary algorithms as well...
-
THERMODYNAMIC ANALYSIS OF A GENERATION IV SCWR NUCLEAR POWER PLANT CYCLE
PublicationThis article presents a flow and thermodynamic analysis of a Generation IV nuclear cycle. An SCWR (Supercritical water reactor) is a high temperature and high pressure reactor that uses water at a temperature above its thermodynamic critical point as the working fluid. The cycle used for the calculations consists of one interstage superheater and 7 regenerative heat exchangers. Division pressure was optimized in view of the cycle efficiency,...
-
RENOVATION OF ARCHIVE AUDIO RECORDINGS USING SPARSE AUTOREGRESSIVE MODELING AND BIDIRECTIONAL PROCESSING
PublicationThe paper presents a new approach to elimination of broadband noise and impulsive disturbances from archive audio recordings. The proposed adaptive Kalman-like algorithm, based on a sparse autoregressive model of the audio signal, simultaneously detects noise pulses, interpolates the irrevocably distorted samples and performs signal smoothing. It is shown that bidirectional (forward-backward) processing of the archive signal improves...
-
Method of sacrificial anode transistor-driving in cathodic protection system
PublicationA magnesium anode driving system has been proposed. A PNP driving transistor has been used. Electrochemical testing in 3%NaCl, results and comparison of the driving system and classic direct anode to cathode connection are presented. The driving system reduced the protection current and stabilized the working conditions of the anode. Higher anode efficiency was achieved. Overprotection and hydrogen embrittlement threats were prevented...
-
Application of industrial waste as a carbon source for biosurfactants production
PublicationBiosurfactants are natural surfactants produced by variety of microorganisms. They are very prospective product due to good biodegradability, low toxicity, good physicochemical properties and high efficiency in many applications. Moreover, they are efficient in wide range of pH, temperatures and salinity. However, the production of biosurfactants is very expensive due to high purification cost. This cost can be minimized by application...
-
Reliability assessment of truss towers using Monte Carlo Method, PEM and RSM
PublicationThe paper discusses the reliability assessment of simple random truss structures using three different probabilistic methodologies: the Monte Carlo method, the Point Estimate Method and the Response Surface Method. A benchmark truss structure example is analyzed. A set of numerical calculations of critical load is performed and the results are taken as the basis of advanced probabilistic calculations. Using the samples, numerical...
-
Musical Instrument Separation Applied to Music Genre Classification . Separacja instrumentów muzycznych w zastosowaniu do rozpoznawania gatunków muzycznych
PublicationThis paper outlines first issues related to music genre classification and a short description of algorithms used for musical instrument separation. Also, the paper presents proposed optimization of the feature vectors used for music genre recognition. Then, the ability of decision algorithms to properly recognize music genres is discussed based on two databases. In addition, results are cited for another database with regard to...
-
An Enhanced Reduced Basis Method for Wideband Finite Element Method Simulations
PublicationIn this paper, we present a novel strategy for selecting expansion points in the reduced basis method. A single computation of the error estimator is used to select a few expansion points in the multi-parameter space simultaneously. The number of selected points is determined adaptively, based on the accuracy of the current reduced model. The reliability and efficiency of this proposed approach are illustrated by numerical tests...
-
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublicationThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
Hysteresis modelling of a medium frequency single-phase transformer
PublicationThe article describes a feedback Preisach hysteresis model equivalent circuit implementation of a medium frequency single-phase transformer being a part of a high power and high efficiency DC-DC converter. The macroscopic models of magnetic hysteresis are introduced and the feedback Preisach model is selected for further analysis. The hysteresis model is developed for a prototype transformer and the hysteresis loops are compared...
-
Design of a SiC based triple active bridge ceil for a multi-megawatt DC-DC converter
PublicationThe paper describes the design methodology of a novel Triple Active Bridge cell used as the building block for modular DC-DC converters. The intended application is for Medium Voltage Direct Current grids, such as the DC collector for offshore wind farms. The latest generation of SiC MOSFET semiconductors is utilized to operate in the medium frequency range while optimizing the efficiency. The dimensioning of the main cell components,...
-
Analysis of the parameters of respiration patterns extracted from thermal image sequences
PublicationRemote estimation of vital signs is an important and active area of research. The goal of this work was to analyze the feasibility of estimating respiration parameters from video sequences of faces recorded using a mobile thermal camera. Different estimators were analyzed and experimentally verified. It was demonstrated that the respiration rate, periodicity of respiration, and presence and length of apnea periods could be reliably...
-
Reduction of Computational Complexity in Simulations of the Flow Process in Transmission Pipelines
PublicationThe paper addresses the problem of computational efficiency of the pipe-flow model used in leak detection and identification systems. Analysis of the model brings attention to its specific structure, where all matrices are sparse. With certain rearrangements, the model can be reduced to a set of equations with tridiagonal matrices. Such equations can be solved using the Thomas algorithm. This method provides almost the same values...
-
OPTIMAL FARM SIZE AND EFFECTIVENESS OF AGRICULTURE IN THE EU: THE CASE OF WHEAT YIELDS
PublicationThe article concentrates on the relationship between the size of a farm and its efficiency in relation to wheat production in the European Union (EU). The issue is not new, however fundamental from the point of view of the agricultural policy, as the appropriate shape of the agrarian structure affects the economic rationality in agriculture and significantly improves the productivity. We analysed data for the period between 2004...
-
A Strategy for Managing the Operation of Technical Infrastructure Based on the Analysis of “Bad Actors”—A Case Study of LOTOS Group S.A.
PublicationThe article covers issues related to the selection of a management strategy for the operation of technical infrastructure. It contains the approaches, methodology and a general model of the system of operation of the Maintenance Services of the LOTOS Group production company, which is an example of a large oil concern. Nowadays, an increasing aspect is put on the efficiency of individual repair processes, as well as the operation...
-
The Analysis of Working Parameters Decrease in Photovoltaic Modules as a Result of Dust Deposition
PublicationThe aspect of dust accumulation on the surface of photovoltaic (PV) modules should be thoroughly understood in order to minimize possible obstacles affecting energy generation. Several elements affect the amount of pollutant gathered on the surface of a solar device, mainly its localization, which is irreversibly linked to factors such as annual rainfall, occasional snow coverage, or, in a dry climate, increased blow of dust during...
-
Exergetic Analysis of the nCO2PP Cycle with Particular Reference to the Exergy Destruction of Sewage Sludge Due to Gasification
PublicationAn exergy analysis is carried out on the negative CO2 emission gas power plant (nCO2PP), which integrates the process sections of fuel preparation, power generation and carbon capture. Processes of exergy destruction are studied with particular focus on the process in the gasification unit of the fuel preparation section, where a large amount of exergy is destroyed in various chemical reactions from sewage sludge to producer gas...
-
Engineering TADF, Mechanochromism, and Second Harmonic Up- conversion Properties in Regioisomeric Substitution Space
PublicationThis research article explores the distinct TADF efficiency of three donor-acceptor based regio-isomers: DPAOCN (ortho- isomer), DPAMCN (meta-isomer), and DPAPCN (para-isomer). DPAPCN exhibits maximum TADF efficiency in both solution and solid-state with an impressive reverse inter-system crossing (RISC) rate of ~ 106 s-1; the underlying cause being the minimum singlet-triplet splitting energy or ∆EST and maximum SOC (spin-orbit...
-
MOF/TiO2 erythrocyte-like heterostructures decorated by noble metals for use in hydrogen photogeneration and pollutant photodegradation
PublicationVarious metal–organic framework (MOF)/TiO2 heterostructures can be obtained by the partial hydrolysis or calcination of Ti-based MOFs. By adjusting the hydrolysis and calcination steps of NH2-MIL-125 (Ti), a novel photoactive material composed of a MOF (NH2-MIL-125 (Ti)) and TiO2, with a unique “erythrocyte” shape, was developed. Furthermore, modification of the composition prepared by the partial hydrolysis of NH2- MIL-125 (Ti)...
-
Resource constrained neural network training
PublicationModern applications of neural-network-based AI solutions tend to move from datacenter backends to low-power edge devices. Environmental, computational, and power constraints are inevitable consequences of such a shift. Limiting the bit count of neural network parameters proved to be a valid technique for speeding up and increasing efficiency of the inference process. Hence, it is understandable that a similar approach is gaining...
-
Core loss resistance impact on sensorless speed control of an induction motor using hybrid adaptive sliding mode observer
PublicationInduction motors (IMs) experience power losses when a portion of the input power is converted to heat instead of driving the load. The combined effect of copper losses, core losses, and mechanical losses results in IM power losses. Unfortunately, the core losses in the motor, which have a considerable impact on its energy efficiency, are not taken into account by the generally employed dynamic model in the majority of the studies. Due...
-
Ti/TiO2 nanotubes sensitized PbS quantum dots as photoelectrodes applied for decomposition of anticancer drugs under simulated solar energy
PublicationOne of the challenges in research into photoelectrocatalytic (PEC) degradation of pollutants is finding the appropriate photoanode material, which has a significant impact on the process efficiency. Among all others, photoelectrodes based on an ordered TiO2 nanotube arrays are a promising material due to well-developed surface area and efficient charge separation. To increase the PEC activity of this material, the SILAR method was...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublicationResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
Diaryl Sulfide Derivatives as Potential Iron Corrosion Inhibitors: A Computational Study
PublicationThe present work aimed to assess six diaryl sulfide derivatives as potential corrosion inhibitors. These derivatives were compared with dapsone (4,4′-diaminodiphenyl sulfone), a common leprosy antibiotic that has been shown to resist the corrosion of mild steel in acidic media with a corrosion efficiency exceeding 90%. Since all the studied compounds possess a common molecular backbone (diphenyl sulfide), dapsone was taken as the...
-
Evaluation of Partial Nitritation/Anammox (PN/A) Process Performance and Microorganisms Community Composition under Different C/N Ratio
PublicationA one-stage partial nitritation/anammox (PN/A) process with intermittent aeration is possible under sidestream conditions, but implementation in a mainstream is a challenge due to increased Carbon/Nitrogen (C/N) ratios in domestic wastewater. This study investigated the effect of C/N ratios on process efficiency and the effect of narrowing non-aeration time on process improvement at high chemical oxygen demand (COD) load. An increase...
-
Comparative analysis of thermodynamic cycles of selected nuclear ship power plants with high-temperature helium-cooled nuclear reactor
PublicationThis paper presents a comparative analysis of thermodynamic cycles of two ship power plant systems with a high-temperature helium- cooled nuclear reactor. The first of them is a gas system with recuperator , in which classical gas chamber is substituted for a HTGR reactor (High Temperature Gas-cooled Reactor) . The second of the considered cycles is a combined gas-steam system where working medium flux from gas turbine outlet...
-
Computer Simulation in Predicting Biochemical Processes and Energy Balance at WWTPs
PublicationNowadays, the use of mathematical models and computer simulation allow analysis of many different technological solutions as well as testing various scenarios in a short time and at low financial budget in order to simulate the scenario under typical conditions for the real system and help to find the best solution in design or operation process. The aim of the study was to evaluate different concepts of biochemical processes and...
-
Enhanced photocatalytic, electrochemical and photoelectrochemical properties of TiO2 nanotubes arrays modified with Cu, AgCu and Bi nanoparticles obtained via radiolytic reduction
PublicationTiO2 nanotubes arrays (NTs), obtained via electrochemical anodization of Ti foil, were modified with monometallic (Cu, Bi) and bimetallic (AgCu) nanoparticles. Different amounts of metals’ precursors were deposited on the surface of NTs by the spin-coating technique, and the reduction of metals was performed via gamma radiolysis. Surface modification of titania was studied by EDS and XPS analysis. The results show that AgCu nanoparticles...