Filters
total: 1565
filtered: 901
Search results for: DIMENTIONS
-
New Design of Axial Piston Pump with Displaced Swash Plate Axis of Rotation for Hydro-Mechanical Transmissions
PublicationThis paper presents a prototype design of an axial piston pump with displaced swash plate axis of rotation in two directions of discharge with electronic control intended for installation on a hydraulic-mechanical gearbox dedicated to working machines. The effect of displacement of the swash plate rotation axis on dead space volume and volumetric efficiency is presented. The construction and principle of operation of the capacity...
-
Experimental tests and numerical simulations of full scale composite sandwich segment of a foot- and cycle- bridge
PublicationIn the paper experimental tests and numerical simulations of a full cross-section segment of ultimately designed foot-and cycle-bridge are presented. The experimental tests were conducted on element with length reduced to 3 m and unchanged (target) cross-section dimensions. The external skin of structure is GFRP laminate while internal core is PET foam. Several quasi-static tests were performed using hydraulic cylinder to generate...
-
Miniaturized impedance analyzer using AD5933
PublicationThe paper presents the analyzer allowing to measure impedance in a range of 10 ohms <|Zx|<10 Gohms in a wide frequency range from 10 mHz up to 100 kHz. The device specific features are: miniaturization, low power consumptions and the use of impedance measurement method based on DSP. These features were possible thanks to the use of newest generation of large scale integration chips: e.g. „system on a chip” microsystems (AD5933)...
-
Miniaturized impedance analyzer using AD5933
PublicationThe paper presents the analyzer allowing to measure impedance in a range of 10 ohms <|Zx|<10 Gohms in a wide frequency range from 10 mHz up to 100 kHz. The device specific features are: miniaturization, low power consumptions and the use of impedance measurement method based on DSP. These features were possible thanks to the use of newest generation of large scale integration chips: e.g. „system on a chip” microsystems (AD5933)...
-
Influence of Dielectric Overlay Permittivity on Size and Performance of Miniaturized ESPAR Antenna
PublicationIn this paper, influence of dielectric overlay permittivity on miniaturized ESPAR antenna parameters is presented. ESPAR antenna is a low-cost and energy-efficient way to implement beam steering capability to a node and improve network performance. The antenna size reduction is obtained by embedding its active and passive elements in ABS based materials of relative permittivity equal to 4, 5.5 and 7.5 in order to achieve network...
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublicationAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublicationAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
The influence of compensate coils on own ship magnetic field
PublicationA ferromagnetic object placed in the earth magnetic field causes a local disturbance in this field distribution. The field distribution disturbance is a function of many arguments like the dimensoins and shape of the object, its ferromagnetic properties ande its positon in relation to the earth magnetic field. in order to minimize the influence of this disturbance one places compensate coils on the ship. Some chosen results of...
-
Management of Textual Data at Conceptual Level
PublicationThe article presents the approach to the management of a large repository of documents at conceptual level. We describe our approach to representing Wikipedia articles using their categories. The representation has been used to construct groups of similar articles. Proposed approach has been implemented in prototype system that allows to organize articles that are search results for a given query. Constructed clusters allow to...
-
Human emotion recognition with biosignals
PublicationThis chapter presents issues in the field of affective computing. Basic preliminary information for the recognition of emotions is given and models of emotions, various ways of evoking emotions, as well as their theoretical foundations are discussed. The particular attention is given to the use of physiological signals in recognizing emotions. This subject is outlined further below by presenting selected biosignals, their relationship...
-
Terminological and Assertional Queries in KQL Knowledge Access Language
PublicationOne of the directions of development of information systems in recent years in the evolution of data-based systems into the knowledge-based systems. As a part of this process there is ongoing work on a whole range of languages for accessing knowledge bases. They can be used in a variety of applications, however their main drawback is the lack of clearly defined algebra representing a theoretical basis for them. For instance, such...
-
The role and concept of sub-models in the smart fuzzy model of the internet mortgage market
PublicationThe paper introduces some challenges of the fast growing mortgage market in Poland. One of these challenges is the need for a model development that could be used for various predictions related to this market. At the current stage of the model evelopment process our main goal is to propose and introduce sub-models the role of which would be to describe three different economic environments: stable, fast growing, and recession....
-
Seawater intrusion due to pumping mitigated by natural freshwater flux: a case study in Władysławowo, northern Poland
PublicationThe paper presents a case study of seawater intrusion into a coastal aquifer, caused by a groundwater intake located close to the seashore in Władysławowo, northern Poland. Evolution of the basic hydrogeochemical parameters for the 50-year period from 1964 to 2014 indicates progressing encroachment of saline seawater into the aquifer. However, the spatial pattern of salinity was influenced by the variability of hydraulic gradient...
-
The differential impact of a density of Polish pine wood on cutting forces with its origin region taken into consideration
PublicationIn the article the dependence of cutting forces in a function the density of wood with regard to the wood origin are presented. Samples used in experiment were with Scotch pine (Pinus sylvestris L.) originating from four provenances in Poland (Figure 1). Wood density was measured by two methods: stereometric method (global density) and radiometric method (local density). Stereometric method consists in measurements the volume...
-
Music Mood Visualization Using Self-Organizing Maps
PublicationDue to an increasing amount of music being made available in digital form in the Internet, an automatic organization of music is sought. The paper presents an approach to graphical representation of mood of songs based on Self-Organizing Maps. Parameters describing mood of music are proposed and calculated and then analyzed employing correlation with mood dimensions based on the Multidimensional Scaling. A map is created in which...
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublicationIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Literature Review on Conceptualisation of Online Consumer Engagement
PublicationThe purpose of the current study is to develop a literature review on “online consumer engagement” (OCE). Articles from 2006 to 2016 published in the marketing journals and other related journals have been reviewed to summarise the OCE concept. Although there is not an agreed definition and conceptualisation of OCE, this study classified the concept as either behavioural or psychological within the dimensions of cognitive, emotional,...
-
A derivatisation agent selection guide
PublicationThe development of new tools for providing high quality information in a cost-effective and expeditious way is one of the main aims of analytical chemistry. Remarkably, the introduc- tion of the 12 principles of green chemistry paved the way forward for the development of analytical methodologies that are, ideally, inherently safe for the operator and the environ- ment, with the least possible consumption of energy and chemicals,...
-
Substrate Dependence in the Formation of Au Nanoislands for Plasmonic Platform Application
PublicationIn this work, the influence of the various substrates on Au nanoisland formation has been studied. Nanostructures were obtained via annealing of thin Au films. In order to determine nanoisland formation mechanisms, correlation between an initial film thickness and temperature of formation, shapes, and dimensions of nanostructures was examined. For the surface morphology studies, nanograin structure, and chemical composition analysis,...
-
Measuring Consumers' Engagement With Brand-Related Social-Media Content. Development and Validation of a Scale that Identifies Levels of Social-Media Engagement with Brands
PublicationThe purpose of the current study was to develop a scale to measure the consumer's engagement with brand-related social-media content, based on three dimensions established in the framework of an earlier theoretical construct, “Consumer's Online Brand-Related Activities” (Muntinga, Moorman, and Smit, 2011). Qualitative techniques were used to generate an initial pool of items that captured different levels of consumer engagement...
-
Residue-Pole Methods for Variability Analysis of S-parameters of Microwave Devices with 3D FEM and Mesh Deformation
PublicationThis paper presents a new approach for variability analysis of microwave devices with a high dimension of uncertain parameters. The proposed technique is based on modeling an approximation of system by its poles and residues using several modeling methods, including ordinary kriging, Adaptive Polynomial Chaos (APCE), and Support Vector Machine Regression (SVM). The computational cost is compared with the traditional Monte-Carlo...
-
Applications of Additively Manufactured Tools in Abrasive Machining—A Literature Review
PublicationHigh requirements imposed by the competitive industrial environment determine the development directions of applied manufacturing methods. 3D printing technology, also known as additive manufacturing (AM), currently being one of the most dynamically developing production methods, is increasingly used in many different areas of industry. Nowadays, apart from the possibility of making prototypes of future products, AM is also used...
-
Polish waterfront in the process of transformation: The case of Elbląg port city
PublicationThe topic of waterfront transformation is a vast and challenging issue, which in small and medium-sized cities is still unexplored. With growing global interest in the matter of regeneration of city-water relationship and increasing public awareness of the value of waterfront public spaces, actions to transform abandoned waterfront areas have been undertaken in many Polish port cities. City of Elbląg, located in northern Poland,...
-
Cluster organization as a form of non-technological innovation
PublicationThe paper aims to investigate the relationships that cluster enterprises develop with their environment through participation in cluster organization (CO). The authors report the findings from a qualitative study carried out in the Lubusz Metal Cluster. The main research strategy is case study. An in-depth individual interview was used to collect the data, and qualitative content analysis and coding for its analysis. The study...
-
Analysis of inductive power transfer systems for variable air gap and voltage supply frequency
PublicationThe paper describes an IPT system, by which electrical energy may be transmitted through a large air gap between coils without electrical connection. It presents theoretical and simulation analysis of IPT, which allows for supplying a receiver in the conditions of slow, in relation to the dynamics of power supply, changes in dimension of the air gap. The influence of frequency characteristics of the system on the possible selection...
-
THE INFLUENCE OF PET MECHANICAL PROPERTIES ON SBM PROCESS PARAMETERS – LITERATURE REVIEW
PublicationIn the paper it is said about the influence of PET (polyethylene terephthalate) mechanical properties on SBM (stretch blow molding) process output parameters changes. The below paper mentions also about the influence of PET orientation and crystallization processes on mechanical and thermal properties of PET material during SBM process. All mechanical data of PET material and SBM process output parameters changes are from collected...
-
Experiences from operation of various expansion devices in small scale ORC
PublicationThe main aim of this paper was to present various expansion devices for an application in the small scale ORC system. The investigations were carried out in two parallel directions. One direction was to design and construct a device dedicated to the analyzed ORC system. The second direction was to adapt existing expansion devices for the needs of the analyzed ORC system. Four various devices were described and presented together...
-
Camera angle invariant shape recognition in surveillance systems
PublicationA method for human action recognition in surveillance systems is described. Problems within this task are discussed and a solution based on 3D object models is proposed. The idea is shown and some of its limitations are talked over. Shape description methods are introduced along with their main features. Utilized parameterization algorithm is presented. Classification problem, restricted to bi-nary cases is discussed. Support vector...
-
Retrieval with Semantic Sieve
PublicationThe article presents an algorithm we called Semantic Sieve applied for refining search results in text documents repository. The algorithm calculates socalled conceptual directions that enables interaction with the user and allows to narrow the set of results to the most relevant ones. We present the system where the algorithm has been implemented. The system also offers in the presentation layer clustering of the results into...
-
Mechanical properties for preliminary design of structures made from PVC coated fabric
PublicationIn this paper, laboratory tests necessary for the identification of non-linear elastic immediate properties of the PVC coated polyester fabric (like AF 9032) are described. The material parameters are specified on the basis of the uniaxial tensile tests in the warp and weft directions as well as on the base of the biaxial tensile tests. For the identification process techniques based on the least squares method are used. The authors...
-
Simulation of Parallel Applications on Large-scale Distributed Systems
PublicationThis chapter has a form of a review article in the field of simulating High-Performance Computing systems. We justify the need for a new versatile simulator considering heterogeneity, energy efficiency and reliability of HPC systems. We sketch the problems that need to be solved by such simulator and rationalize using discrete-event simulation for this purpose. Based on a review of existing discrete-event HPC simulation solutions...
-
Auditory Display Applied to Research in Music and Acoustics . Obrazowanie dźwiękowe w muzyce i akustyce.
PublicationThis paper presents a relationship between Auditory Display (AD) and the domains of music and acoustics. First, some basic notions of the Auditory Display area are shortly outlined. Then, the research trends and system solutions within the fields of music technology, music information retrieval and music recommendation and acoustics that are within the scope of AD are discussed. Finally, an example of AD solution based on gaze...
-
Investigation of abdomen surface deformation due to life excitation: implications for implant selection and orientation in laparoscopic ventral hernia repair
PublicationVentral hernia is a common medical problem. Statistically there are around 10% recurrences of the sickness. The authors' former investigation proved edges of the hernia orifice displacements to be one of the factors causing recurrence. Thus, experimental investigation of the abdomen surface deformation due to some normal activities of people is studied.The extreme strains, their localization and directions are identified. The acquired...
-
Technology brands in the digitally-based and network economy. Setting the background
PublicationThis chapter defines and draws a general picture on Digital Technologies and Technology Brands’ meaning in the current economy. It contextualises the role and channels of digital technology’s impact on their shaping technology brands in network economy. It briefly explains why digital, innovative technologies constitute a perfect background and environment for technology brands of global scope. It discusses the place of technology...
-
Real and imaginary motion classification based on rough set analysis of EEG signals for multimedia applications
PublicationRough set-based approach to the classification of EEG signals of real and imaginary motion is presented. The pre-processing and signal parametrization procedures are described, the rough set theory is briefly introduced, and several classification scenarios and parameters selection methods are proposed. Classification results are provided and discussed with their potential utilization for multimedia applications controlled by the...
-
Virtual Sightseeing in Immersive 3D Visualization Lab
PublicationThe paper describes the modern Immersive 3D Visualization Lab (I3DVL) established at the Faculty of Electronics, Telecommunications and Informatics of the Gdańsk University of Technology (GUT) and its potential to prepare virtual tours and architectural visualizations on the example of the application allowing a virtual walk through the Coal Market in Gdańsk. The paper presents devices of this laboratory (CAVE, walk simulator etc.),...
-
Interaktywne fasady przeszklone w architekturze współczesnej (w kontekście zrównoważonego rozwoju)
PublicationArtykuł dotyczy projektowania przeszklonych elewacji interaktywnych we współczesnej architekturze. Na podstawie wybranych przykładów przedstawiono współczesne rozwiązania oraz możliwe kierunki rozwoju przeszkleń elewacji budynków realizowanych zgodnie z ideą zrównoważonego rozwoju.
-
Chemical Vapor Transport Route toward Black Phosphorus Nanobelts and Nanoribbons
PublicationChemical vapor transport (CVT) method is widely used for bulk black phosphorus (BP) fabrication. In this work, we demonstrate that CVT provides a route for the fabrication of BP nanoribbons and nanobelts. This method consists of a two-step procedure, including initial BP column growth using the CVT technique, followed by ultrasonic treatment and centrifugation. The obtained nanostructures preserve BP column dimensions, forming...
-
Chemical Vapor Transport Route toward Black Phosphorus Nanobelts and Nanoribbons
PublicationChemical vapor transport (CVT) method is widely used for bulk black phosphorus (BP) fabrication. In this work, we demonstrate that CVT provides a route for the fabrication of BP nanoribbons and nanobelts. This method consists of a two-step procedure, including initial BP column growth using the CVT technique, followed by ultrasonic treatment and centrifugation. The obtained nanostructures preserve BP column dimensions, forming...
-
Novel structure and EM-driven design of miniaturized microstrip rat-race coupler
PublicationIn this paper, a novel structure and design procedure of a miniaturized microstrip rat-race coupler (RRC) is described. Small size of the RRC is achieved by folding the transmission lines of the conventional circuit into its interior, as well as by implementation of the structure on three layers. The final size of the coupler realized for the operating frequency of 1 GHz is only 220 mm2, which gives over 95% footprint reduction...
-
Determination of the dynamic critical maneuvering area in an encounter between two vessels: Operation with negligible environmental disruption
PublicationThis paper introduces the concept of Collision Avoidance Dynamic Critical Area (CADCA) for onboard Decision Support Systems (DSS). The indicator proposed is derived via identification of a minimum required maneuvering zone in an encounter between two vessels. The CADCA model accounts for ship maneuvering dynamics and associated hydrodynamic actions emerging from different rudder angles and forward speed effects. The method presented...
-
Storing thermal energy from solar collectors for the needs of a detached house
PublicationThis work evaluates the possibility of meeting a single familu household's need for hot water and heat year round, using solar collectors as the sole energy sourse. The main flaw of energetic systems based on solar energy is that the energy supply is usually insufficient in winter, when it is most needed. This work is going to show thatm for a house surface of 150 m2 and base dimension of 10x10m, it is possible to supply sufficient...
-
Selection of Features for Multimodal Vocalic Segments Classification
PublicationEnglish speech recognition experiments are presented employing both: audio signal and Facial Motion Capture (FMC) recordings. The principal aim of the study was to evaluate the influence of feature vector dimension reduction for the accuracy of vocalic segments classification employing neural networks. Several parameter reduction strategies were adopted, namely: Extremely Randomized Trees, Principal Component Analysis and Recursive...
-
Load test of new European record holder in span length among extradosed type bridges
PublicationThe article presents acceptance load tests of a newly built extradosed MS-3 bridge located along the national road DK-16 near Ostróda (Poland). The structure features significant dimension in European reference scale. It is a new record holder in span length regarding this distinct bridge category. Its length ranges 206 m. Static and dynamic load tests were performed here. The program was extended by entire structural laser scanning...
-
Features of irregularity in examples of Polish multi-family architecture constructed in 2011–2021 and nominated for the Mies van der Rohe award
PublicationThis article is devoted to the analysis of contemporary Polish multi-family architecture in the context of aesthetic irregularity. The research was limited to constructions from 2011–2021 and nominated for the Mies van der Rohe award as the objects with the greatest potential impact on shaping further trends. In their research, the authors focused on searching for the features of irregularities, which, in their opinion, have become...
-
Reconstruction of 3D image of corona discharge streamer
PublicationIn this paper, the method of reconstruction of the 3D structure of streamers in DC positive corona discharge in nozzle-to-plate electrode configuration is presented. For reconstructing of 3D image of corona discharge streamer we propose a stereographical method, where streamers are observed from several directions simultaneously. The multi-directional observation enabled to obtain fine positional coordinates of streamers for a...
-
Exploring the trends in flux-cored arc welding: scientometric analysis approach
PublicationFlux-cored arc welding (FCAW) is a universal group of welding methods in terms of the scope of application and automation possibilities, the share of which in various industries in many countries is still increasing. The paper presents the results of bibliographic analyses (scientometric analysis with the use of VOSviewer, Bibliometrix and CitNetExplorer tools) of a data set of 993 publications indexed in the Web of Science database...
-
A fast procedure of stress state evaluation in magnetically anisotropic steels with the help of a probe with adjustable magnetizing field direction
PublicationThe paper presents a novel approach to the stress state evaluation issue. It deals with a strongly (magnetically) anisotropic materials for which a direct interpretation of the Barkhausen effect (BE) intensity would lead to erroneous results. In such a case one has to take into account both the measured BE intensity and the orientation of the magnetisation direction relative to the magnetic easy axis. For the in plane stress distribution...
-
IN SEARCH OF A NEW EXHIBITION SPACE
PublicationThe buildings considered as raising the prestige and promoting cities are those related to culture. Their impact on urban life is undeniable, which is reflected in a continuous increase in the number of new museum buildings. Apart from places intrinsically linked with culture, which, as such, may be considered as standard - like museum, theatres or galleries - there also appear alternative places of development and promotion of...
-
Psychometric properties of the polish version of the job-related affective well-being scale
PublicationObjectives: The aim of this study was to verify psychometric properties of the Polish version of the Job-related Affective Well-being Scale (JAWS). Specifically, theoretical 4-factor structure (based on the dimensions of pleasure and arousal) and reliability of the original – 20-item JAWS (van Katwyk et al., 2000) and the shortened – 12-item (Schaufeli and Van Rhenen, 2006) versions were tested. Material and Methods: Two independent...