Filters
total: 1008
filtered: 669
Search results for: TRANSNATIONAL CORPORATION
-
Optical and chemical characterization of thin TiNx films deposited by DC-magnetron sputtering
PublicationThin titanium nitride (tinx) films were deposited on silicon substrates by means of a reactive dc-magnetron plasma. Layers were synthesized under various conditions of discharge power and nitrogen flows in two operation modes of the magnetron (the so-called "balanced" and "unbalanced" modes). The optical constants of the tinx films were investigated by spectroscopic ellipsometry (se). X-ray photoelectron spectroscopy (xps) was...
-
Distributed protection against non-cooperative node behavior in multi-hop wireless networks
PublicationAn important security problem in today's distributed data networks is the prevention of non-cooperative behavior i.e., attacks consisting in the modification of standard node operation to gain unfair advantage over other system nodes. Such a behavior is currently feasible in many types of computer networks whose communication protocols are designed to maximize the network performance assuming full node cooperation. Moreover, it...
-
New insights of nanomaterials usage toward superhydrophobic membranes for water desalination via membrane distillation: A review
PublicationMembrane distillation (MD) is a promising technology for seawater desalination due to the ability to process high-salinity waters and the ability to be driven by low-grade or waste heat. However, practical applications of MD membranes are limited by the low vapor flux and fouling problem. Recently, there is a growing interest in developing novel MD membrane materials with enhanced hydrophobicity to improve the efficiency of desalination...
-
Morphology and the physical and thermal properties of thermoplastic polyurethane reinforced with thermally reduced graphene oxide
PublicationIn this study, thermally reduced graphene oxide (TRG)-containing polyurethane nanocomposites were obtained by the extrusion method. The content of TRG incorporated into polyurethane elastomer systems equaled 0.5, 1.0, 2.0 and 3.0 wt%. The morphology, static and dynamic mechanical properties, and thermal stability of the modified materials were investigated. The application of TRG resulted in a visible increase in material stiffness...
-
A Centralized Reputation System for MANETs Based on Observed Path Performance
PublicationA reputation system for MANETs is described that attempts to deduce nodal trustworthiness (forwarding behaviour) from observed end-to-end path performance. The trustworthiness deduction algorithm produces interval estimates and works well if node misbehaviour is not selec-tive with respect to traversing paths. Nodal reputation levels are next calculated in the spirit of generous tit-for-tat so as to best reflect momentary nodal...
-
X-ray and UV Radiation Damage of dsDNA/Protein Complexes
PublicationRadiation and photodynamic therapies are used for cancer treatment by targeting DNA. However, efficiency is limited due to physico-chemical processes and the insensitivity of native nucleobases to damage. Thus, incorporation of radio- and photosensitizers into these therapies should increase both efficacy and the yield of DNA damage. To date, studies of sensitization processes have been performed on simple model systems, e.g.,...
-
The Role of a Software Product Manager in Various Business Environments
PublicationThe aim of the paper is to identify the role of the software product manager depending on the size of the company and the characteristics of the product they are working on. This has been achieved in cooperation with 15 experts from the IT industry. The companies were divided into 4 levels of size: micro-enterprises, small businesses, medium businesses and large enterprises. The characteristics of the products were divided into...
-
INTERNAL DETERMINANTS OF FIRMS’ INNOVATIVENESS
PublicationThis article presents an analysis of the determinants of a firm’s innovativeness deriving from its internal potential and characteristics. The analysis is based on research carried out on 1355 firms that applied for public subsidies from the Innovative Economy Operational Program in 2014. The methods applied are logit regression, comparative analysis and literature review. The analysis is structured ac- cording to Bielski’s model...
-
The design of an intelligent medical space supporting automated patient interviewing
PublicationThe article presents the architecture and results of implementing an application for the intelligent medical space UbiDoDo (Ubiquitous Domestic Doctor's Office). The main purpose of the application is real-time monitoring of the biomedical parameters of a patient in his domestic environment. It allows an immediate reaction to appearing symptoms and provides means to automatically interview the patient and deliver his results to...
-
Solution of the dike-break problem using finite volume method and splitting technique
PublicationIn the paper the finite volume method (FVM) is presented for the solution of two-dimensional shallow water equations. These equations are frequently used to simulate the dam-break and dike-break induced flows. The applied numerical algorithm of FVM is based on the wave-propagation algorithm which ensures a stable solution and simultaneously minimizes the numerical errors. The dimensional decomposition according to the coordinate...
-
Comparative study of a combined heat and power plant retrofitted by CO2 capture during the combustion of syngas from sewage sludge gasification versus zero-emission combustion of hydrogen produced using renewables
PublicationWith ecological requirements aimed at limiting the production of CO2, it is necessary to produce all, or most of the energy from RES. During the transformation process, ecological and highly efficient combustion power plants will be needed. The classic cycle of combined heat and power (CCGT) with green improvements will continue to be one of the most suitable technologies for this task. This article presents the modernization of...
-
Dissolution of Nb-doped hydroxyapatite prepared via low-temperature mechanochemical method: Spectroscopy studies
PublicationCalcium phosphate glass ceramics with nominal hydroxyapatite stoichiometry doped with niobium were synthesized using simple as well as low-temperature mechanochemical method and then in the form of compressed pellet were submitted to the static dissolution process in distilled water for one month. The results of structural analysis, performed mainly on the base of spectroscopic methods such as: infrared absorption spectroscopy,...
-
The landscape in the informal education of the youngest
PublicationThe European Landscape Convention, adopted in 2000, aims to promote the protection, management and planning of landscapes and to organise cooperation on landscape-related issues. Countries that ratified the Convention undertook to introduce activities that would promote public education on the subject. In Poland, the Ministry of Education has identified schools as the place to implement...
-
Informal projects management with volunteers participation
PublicationThe article briefly presents some experiences and results of research which has been conducted in order to identify key elements influencing the success of projects managed in informal way with volunteers’ participation. These experiences were collected during the realization of several “soft” projects. The general aims of these projects were sports competitions’ organisation, cultural events and charity projects for...
-
COMPARATIVE ANALYSES OF INTERNATIONALIZATION OF KAZAKHSTAN ENTERPRISES
PublicationThis paper presents the instruments of internationalization of enterprises operating within the Eurasian Economic Union. Research contains answers of 108 enterprises exporters located in the Republic of Kazakhstan. The purpose of the paper is to show the main forms of the internationalization of enterprises in Kazakhstan. The paper also presents the following instruments of enterprises’ internationalization including: indirect...
-
RECODIS: Resilient Communication Services Protecting End-user Applications from Disaster-based Failures
PublicationDisaster-based failures can seriously disrupt any communication network, making its services unavailable. Such disruptions may be caused by natural disasters, technology-related failures, or malicious attacks, and they are observably increasing in number, intensity and scale. When network services that are a part of critical infrastructure become unavailable, commercial and/or societal problems are inevitable. The issue of limiting...
-
THE INTERACTION BETWEEN STEEL COLUMN CHORD AND CLOSELY SPACED REINFORCEMENT.
PublicationNowadays, more often than before, civil engineering designers are willing to use steel build-up members composed of single or doubled cold-formed chords interconnected using different mechanical connectors. This paper subject is an analysis of cooperation of a closely spaced built-up cold-formed chord interconnected with series of bolts that are located along the length of the member in a specific spacing. This distance along the...
-
Optimization of the efficiency of braking energy recovery in rail transport by changing arrival time
PublicationThe article refers to the previous work of the authors, in which the model of traffic organization of cooperating trains including the optimization of the use of energy returned to the catenary was presented. In the presented article, the model was modified by changing the main control variable, which affects the efficient use of energy. Departure time was changed for the arrival time of the train to the stop or station. The optimization...
-
Konkursy studenckie jako narzędzie w określaniu potencjału rewitalizacyjnego miejskich terenów zdegradowanych.
PublicationZgodnie z zasadami prowadzenia działań rewitalizacyjnych określonych w ustawie o rewitalizacji obowiązującej od 9 października 2015 r. oraz horyzontalnych wytycznych w zakresie rewitalizacji w programach operacyjnych na lata 2014-2020 faza przygotowawcza procesu rewitalizacji powinna zawierać wielopłaszczyznowe analizy zakończone wnioskami aplikacyjnymi ujętymi w gminnych programach rewitalizacji obszarów zurbanizowanych. Artykuł...
-
INVESTIGATIONS OF THE EMISSION CHARACTERISTICS OF A DUAL-FUEL GAS TURBINE COMBUSTION CHAMBER OPERATING SIMULTANEOUSLY ON LIQUID AND GASEOUS FUELS
PublicationT his study is dedicated to investigations of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. As the object of the research, a low-emission gas turbine combustion chamber with partial premixing of fuel and air inside the outer and inner radial-axial swirls was chosen. The method of the research is based on the numerical solution of the system of differential...
-
Model organizacji ruchu na sieci kolejowej z uwzględnieniem rekuperacji energii
PublicationNa wstępie przeanalizowano aktualny stan wiedzy z zakresu metod wykorzystywania energii z rekuperacji oraz istniejących modeli optymalizujących ich efektywność. Na tej podstawie za główny cel pracy wyznaczono opracowanie metody modyfikacji kolejowego rozkładu jazdy, która doprowadzi do zwiększenia efektywności wykorzystania energii pochodzącej z rekuperacji. W związku z powyższym postawiono tezę, że możliwe jest zwiększenie efektywności...
-
Trouble in Paradise? Barriers to Open Innovation in Regional Clusters in the Era of the 4th Industrial Revolution
PublicationThe purpose of this paper is to provide an insight into the barriers faced by clusters as open innovation intermediaries. Literature review and an empirical study were performed, involving a nation-wide survey, case studies, and in-depth interviews with cluster actors involved in open innovation activities. This article conceptually links open innovation and clusters in the context of the fourth industrial revolution, empirically...
-
Chitin and derivative chitosan-based structures — Preparation strategies aided by deep eutectic solvents: A review
PublicationThe high molecular weight of chitin, as a biopolymer, challenges its extraction due to its insolubility in the solvents. Also, chitosan, as the N-deacetylated form of chitin, can be employed as a primary material for different industries. The low mechanical stability and poor plasticity of chitosan films, as a result of incompatible interaction between chitosan and the used solvent, have limited its industrialization. Deep eutectic...
-
Chitin nanowhiskers from shrimp shell waste as green filler in acrylonitrile-butadiene rubber: Processing and performance properties
PublicationIn this work, chitin nanowhiskers with high crystallinity index were obtained from shrimp shells waste using acid hydrolysis method and then comprehensively characterized. Subsequently, the impact of chitin nanowhisker content on processing and performance of acrylonitrile-butadiene rubber based nanocomposites was evaluated. The results showed that the addition of chitin nanowhiskers increased tensile strength and tear strength...
-
A Noded Carbon Emission Tool (NCET) to Measure Embodied Carbon (EC) in Compositional Cementitious Materials
PublicationThe ever evolving modern construction industry is now producing the highest levels of carbon content adversely affecting the construction associated environment. Although, the impact of carbon induced emission is quite large, but still not enough measurable standards and tools to scale these emission are available. This study contributes to the body of knowledge by providing a Grasshopper based definition to calculate the embodied...
-
Respiratory system modelling and simulation basing on the forced oscilation technique
PublicationConventional methods of testing lung functioning demand a specific respiratory action of the patient. In contrast, the forced oscillation technique (fot) provides measurements obtained with a minimal cooperation of the subject. The aim of this study is to verify the usefulness of the forced oscillation technique modelling in respiratory system diagnosing. in order to do it two models of fot measurements have been considered: the...
-
In-service measurement of the small wind turbine test stand for structural health monitoring
PublicationThis paper presents the research activity performed on a Small Wind Turbine (SWT) test stand. Commercially available turbine was modified towards incorporation of the sensors system for condition monitoring. Installed sensors measure angular shaft position, torque applied from the wind loads, vibration accelerations and last but not least rotational speed. All gathered data are then transferred and processed in Test.Lab by means...
-
Rapid development of custom web application with ruby on rails framework on the example of group project system
PublicationTechnology industry labor market requires engineers with a good preparation for work with project's tasks and team cooperation skills. One of the way for achieve that abilities during technical university education are students group projects. Running of group projects at university brings new challenges, from recruitment of students with required skills for par-ticular project, to lack of industrial procedures and ready to use...
-
REVISING ENTREPRENEURIAL ORIENTATION (EO) IN SOCIAL ENTREPRENEURSHIP, QUALITATIVE EVIDENCE FROM WORK INTEGRATION SOCIAL ENTERPRISES (WISES) FROM POLAND
PublicationEntrepreneurial behaviour and entrepreneurial orientation (EO) of (commercial) entrepreneurship. have received significant scholarly attention in entrepreneurship and management research However, there are insufficient attempts discussing such behaviour and EO in non-profit, and particularly social entrepreneurship context, arguing that EO is higher in such contexts, or remains the same, some new EO dimensions are proposed, existing...
-
Technology Concept of TLP Platform Towing and Installation in Waters with Depth of 60 m
PublicationThe article is part of the design and research work conducted at the Gdansk University of Technology, Faculty of Ocean Engineering and Ship Technology, in cooperation with a number of other research centres, which concerns offshore wind farms planned to be built in the Polish zone of the Baltic sea in the next years. One of most difficult tasks in this project is building suitable foundations for each power unit consisting of a...
-
Multifrequency Wideband Sonar Array
PublicationThis paper describes of new approach to Multifrequency Wideband Arrays (MWA),applied piezocomposite technologies of the array elements. MWA operating in transmitting(Tx) and receiving (Rx) mode on two or three bands, requires state-of-the-art technology andefficient array designing than conventional array in which separate arrays for every band oreven separate Tx and Rx transducers/arrays are used. The new piezocomposite elements...
-
Integration of the sulfate reduction and anammox processes for enhancing sustainable nitrogen removal in granular sludge reactors
PublicationThe Anammox and Sulfate Reduction Ammonium Oxidation processes were compared in two granular sequencing batch reactors operated for 160 days under anammox conditions. It was hypothesized that increasing the concentration of SO42− may positively influence the rate of N removal under anaerobic conditions and it was tested whether SO42− reduction and anammox occur independently or are related to each other. The cooperation of N-S...
-
Interdisciplinary e-collaboration tools / Narzędzia interdyscyplinarnej e-współpracy
PublicationW projektach interdyscyplinarnych niezwykle ważnym czynnikiem jest aktywne konsultowanie i bezpośrednie zastosowanie relatywnie nowo powstałej dziedziny zwanej współpracą interdyscyplinarną. Nawiązywanie interdyscyplinarnej współpracy przynosi wiele korzyści, jednakże niejednokrotnie wiąże się z licznymi problemami i niedogodnościami, a także koniecznością ciągłego doszkalania się i rozszerzania kompetencji zawodowych. Na podstawie...
-
Reactive deposition of TiNx layers in a DC-magnetron discharge
PublicationTiNx layers have been deposited in 'balanced mode' and 'unbalanced mode' of a reactive DC-magnetron plasma (carrier gas argon, reactive gas nitrogen) under different conditions. Discharge power and reactive gas flow have been varied. The layers have been examined by X-ray photoelectron spectroscopy (XPS), X-ray reflectometry (XR), and spectroscopic ellipsometry (SE). The results of the layer analyses were combined with plasma investigations...
-
APPLICATION OF APRIORI ALGORITHM IN THE LAMINATION PROCESS IN YACHT PRODUCTION
PublicationThe article specifies the dependence of defects occurring in the lamination process in the production of yachts. Despite great knowledge about their genesis, they cannot be completely eliminated. Authentic data obtained through cooperation with one of the Polish yacht shipyards during the years 2013–2017 were used for the analysis. To perform a simulation, the sample size was observed in 1450 samples, consisting of 6 models of...
-
Innovation by proxy – clusters as ecosystems facilitating open innovation
PublicationOpen innovation is a concept, whose attributes can be perceived as naturally complementing the proximity-based offer of clusters. The purpose of this paper is to investigate the potential role of clusters as intermediaries of open innovation for cluster members. A literature review and an exploratory study were performed, involving in-depth interviews with experts in the field of innovation and clusters in Poland. This article...
-
Novel Class of Proton Conducting Materials—High Entropy Oxides
PublicationHere, for the first time, we present data on proton conductivity of high-entropy, single-phase perovskites. The BaZr0.2Sn0.2Ti0.2Hf0.2Ce0.2O3−δ, BaZr0.2Sn0.2Ti0.2Hf0.2Y0.2O3−δ, BaZr1/7Sn1/7Ti1/7Hf1/7Ce1/7Nb1/7Y1/7O3−δ, and BaZr0.15Sn0.15Ti0.15Hf0.15Ce0.15Nb0.15Y0.10O3−δ single-phase perovskites were synthesized. Before electrical measurements, materials were characterized using X-ray diffraction (XRD), scanning electron microscopy...
-
Comprehensive thermodynamic analysis of the CAES system coupled with the underground thermal energy storage taking into account global, central and local level of energy conversion
PublicationA key aspect of CAES is the optimal configuration of the thermodynamic cycle. In this paper, the situation of cooperation between the current conventional power plants and wind farms is analyzed, and then, based on thermodynamic models, the process of storing thermal and electrical energy in the CAES system coupled with a heat storage and recovery is developed. Therefore, three levels can be distinguished, namely: the global level...
-
Fundamentals of Physics-Based Surrogate Modeling
PublicationChapter 1 was focused on data-driven (or approximation-based) modeling methods. The second major class of surrogates are physics-based models outlined in this chapter. Although they are not as popular, their importance is growing because of the challenges related to construction and handling of approximation surrogates for many real-world problems. The high cost of evaluating computational models, nonlinearity of system responses,...
-
Proton-Electron Hole Interactions in Sr(Ti,Fe)O3−δ Mixed-Conducting Perovskites
PublicationOxides in which total electrical conductivity is determined by the partial conductivities of three types of charge carriers i.e. holes/ electrons, oxygen ions, and protons are key components of well-functioning proton ceramic fuel cells. Apart from electrochemical properties also easily modified microstructure is an important feature of the electrodes. In the paper, a group of SrTi1−xFexO3−δ (STF, x = 0.2–0.8) perovskites prepared...
-
Cu supported on various oxides as a candidate catalyst for dry methane reforming in DIR-SOFCs systems
PublicationA series of Cu-support systems were tested as potential candidates for DIR-SOFC (Direct Internal Reforming SOFC) catalysts towards a dry reforming of methane (DRM). The various supports (-Al2O3, CeO2, ZrO2, SrTiO3) with comparable specific surface area (SSA), and additionally -Al2O3 with SSA an order of magnitude larger than that of the other supports has been applied. The obtained Cu-support systems were characterized in terms...
-
Waste tire rubber as low-cost and environmentally-friendly modifier in thermoset polymers – a review
PublicationNowadays, waste tire rubber (WTR) management is a growing and serious problem. Therefore, research works focused on the development of cost-effective and environmentally-friendly methods of WTR recycling are fully justified. Incorporation of WTR into polymer matrices and composite materials attracts much attention, because this approach allows sustainable development of industrially applicable waste tires recycling technologies....
-
Hybrid Expert System for Computer-Aided Design of Ship Thruster Subsystems
PublicationThe article presents an expert system supporting the design of ship's power subsystems, in particular the thruster subsystem. The proposed hybrid expert system uses the results of simulation tests as the additional source of knowledge. The results of system operation are collated in a report which can be used as part of ship design description. The work oriented on developing the expert system is the continuation of the research...
-
Using Moodle as a Solution to Interdisciplinary E-collaboration Issues
PublicationRapid technological development in recent years has contributed to numerous changes in many areas of life, including education and communication. Establishing interdisciplinary collaboration brings many benefits, however, it is often associated with numerous problems and inconveniences, as well as the need of constant improvement, lifelong learning, professional development (CPD) and finding an effective way of information transferring....
-
Electron-Induced Decomposition of Uracil-5-yl O-(N,N-dimethylsulfamate): Role of Methylation in Molecular Stability
PublicationThe incorporation of modified uracil derivatives into DNA leads to the formation of radical species that induce DNA damage. Molecules of this class have been suggested as radiosensitizers and are still under investigation. In this study, we present the results of dissociative electron attachment to uracil-5-yl O-(N,N-dimethylsulfamate) in the gas phase. We observed the formation of 10 fragment anions in the studied range of electron...
-
Copper Slag as a Potential Waste Filler for Polyethylene-Based Composites Manufacturing
PublicationThe present study aimed to analyze the application of waste material from copper production– copper slag (ŻŻL) as filler for composites based on the high-density polyethylene (HDPE). Copper slag filler was introduced in the amounts of 1–20 wt%, and its influence on the appearance (color analysis), chemical structure (Fourier-transform infrared (FTIR) spectroscopy), microstructure (optical microscopy), as well as static (tensile...
-
Crossover from charge density wave stabilized antiferromagnetism to superconductivity in Nd1−xLaxNiC2 compounds
PublicationThe path from the charge density wave antiferromagnet NdNiC2 to the noncentrosymmetric superconductor LaNiC2 is studied by gradual replacement of Nd by La ions. The evolution of physical properties is explored by structural, magnetic, transport, magnetoresistance, and specific heat measurements. With the substitution of La for Nd, the Peierls temperature is gradually suppressed, which falls within the BCS mean-field relation for...
-
Biobased Ultralow-Density Polyurethane Foams with Enhanced Recyclability
PublicationPolyurethane (PUR) foams are widely used in many engineering applications, but their efficient recycling has remained a major challenge for many years. This study presents a novel strategy of incorporating hydrolyzable ester units into the PUR structure to enhance PUR foam recyclability. The present ecodesign concept of PUR materials enables fully the replacement of petrochemical polyols with biobased alternatives and production...
-
Influence of silver nanoparticles addition on antibacterial properties of PEO coatings formed on magnesium
PublicationMagnesium is a biodegradable material and thus could be a choice for bone fixation devices and implants with a specific purpose. This study aims to enhance the anti-corrosive, biocompatible, and antibacterial properties on magnesium-based materials through ceramic coatings formation. To achieve this the silicate-based electrolyte was used to create of Plasma Electrolytic Oxidation (PEO) coatings. During investigation the bioactive...
-
Non-linear strain rate analysis of earthquake-induced pounding between steel buildings
PublicationPast and recent earthquakes have shown that ground motions may cause severe structural damage to civil engineering structures. Earthquake-induced pounding between adjacent buildings has been identified as one of the reasons which intensifies damages. The aim of this paper is to show the results of the detailed nonlinear FEM analysis of earthquake-induced pounding between two steel buildings. The elastic – perfectly plastic material...