Filters
total: 4871
-
Catalog
- Publications 3549 available results
- Journals 16 available results
- Conferences 5 available results
- People 43 available results
- Inventions 2 available results
- Projects 5 available results
- Laboratories 1 available results
- Research Equipment 4 available results
- e-Learning Courses 179 available results
- Events 14 available results
- Offers 1 available results
- Open Research Data 1052 available results
displaying 1000 best results Help
Search results for: TESTY PRZESIEWOWE
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublicationThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
Low Power Baseband Processor for M2M Reconfigurable Radio Test Platform
PublicationSoftware Defined Radio (SDR) is becoming more andmore frequently used technique for wireless communication. Itfacilitates as fast prototyping and is a versatile method fordeveloping new communication systems. SDR can be realizedbased on high computational capacity platform, where powerconsumption is no a primary concern like i.e. DVB or BTStransmitters. Another trend are low power systems, whereavailable power in reduced and more...
-
Evaluation of Thermal Stresses in Asphalt Layers in Comparison with TSRST Test Results
PublicationThe paper presents the results of calculations and laboratory determination of thermal stresses at low temperatures. The modified Hills and Brien's method was used to calculate the thermal stresses in asphalt layers of pavements and the results were compared against the values obtained at a laboratory with the Thermal Stress Restrained Specimen Test (TSRST) method. The laboratory investigations were conducted using plain grade...
-
On the influence of shell element properties on the response of car model in crash test
PublicationIt goes without saying that numerical simulations play important role in the modern engineering practice. Contemporary CAD environments combined with FEM solvers, along with computer power of modern processors, give the engineer fast and efficient tool. Ultimately, however it is the user alone who is responsible for the correctness of the results. As long as the FEM calculations remain in the sphere of academic exercise, the inevitable...
-
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublicationThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
A method of Functional Test interval selection with regards to Machinery and Economical aspects
PublicationThis paper discusses the problem of choosing the optimal frequency of functional test, including the reliability calculations and production efficiency, but also the effect of company risk management. The proof test as a part of the functional test interval is well described for the process industry. Unfortunately, this situation is not the case for the machinery safety functions with low demand mode. Afterwards, it is presented...
-
Development and test of fex, a fingers extending exoskeleton for rehabilitation and regaining mobility
PublicationThis paper presents the design process of an exoskeleton for executing human fingers' extension movement for the rehabilitation procedures and as an active orthosis purposes, together with its first clinical usability tests of a robotic exoskeleton. Furthermore, the Fingers Extending eXoskeleton (FEX) is a serial, under-actuated mechanism capable of executing fingers' extension. FEX is based on the state-of-art FingerSpine serial...
-
High-Speed Serial Embedded Deterministic Test for System-on-Chip Designs
PublicationThe paper presents a high-speed serial interface between external tester and Embedded Deterministic Test (EDT) compression logic hosted by SoC designs. With only a single bidirectional link, the system is capable of feeding distributed heterogeneous cores with hundreds of test channels. Moreover, it synergistically supports EDT bandwidth management to improve the overall test performance. A detailed study indicates a high potential...
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
The role of low-energy electrons in the charging process of LISA test masses
PublicationThe estimate of the total electron yield is fundamental for our understanding of the test-mass charging associated with cosmic rays in the Laser Interferometer Space Antenna (LISA) Pathfinder mission and in the forthcoming gravitational wave observatory LISA. To unveil the role of low energy electrons in this process owing to galactic and solar energetic particle events, in this work we study the interaction of keV and sub-keV...
-
Shear band evolution phenomena in direct shear test modelled with DEM.
PublicationA direct shear test is widely used in the geotechnical engineering field. It is an easy and quick test to measure the shear properties of soil. This test often replaces more expensive and difficult tri-axial shear test. Despite that the direct shear test is known and used for a long time, it is still not well investigated at the grain scale. This paper deals with the micro behaviour of the cohesionless sand inside the direct shear...
-
Concept of implementation of open water model tests for assessment of safety of ships in damaged conditions
PublicationPraca zawiera opis koncepcji zastosowania badań modelowych na wodach otwartych w odniesieniu do oceny bezpieczeństwa statków w stanie uszkodzonym. Badania modelowe w omawianym zakresie mogą stanowić alternatywną metodę oceny bezpieczeństwa statków w stanie uszkodzonym lub mogę służyć do weryfikacji oceny bezpieczeństwa statków w stanie uszkodzonym, przeprowadzonej za pomocą metody zawartej w zharmonizowanej wersji konwencji SOLAS...
-
Analysis and Comparison of Safety of Children and Adult Passenger in Car Based on Crash Tests Results
Publication -
Fatigue tests of steel Sandwich panel. Fifth International Conference on Marine Technology and Transportation.
PublicationW referacie przedstawiono wyniki badań laboratoryjnych paneli SANDWICH prowadzonych w Katedrze Technologii Okrętów, Systemów Jakości i Materiałoznawstwa Wydziału OiO na konstrukcjach w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów w wynikami prezentowanymi w literaturze.
-
Model tests and numerical imulations of earth pressure of non - cohesive soil in 3D formulation.
PublicationW artykule przedstawiono wyniki badań modelowych i symulacji numerycznych parcia gruntu działającego na sztywne konstrukcje oporowe. Analizowano stan przestrzennego odkształcenia ośrodka niespoistego. Parcie czynne gruntu za- sypowego wywołano obrotem ściany oporowej wokół osi przechodzącej przez jej górną i dolną krawędź. Przedstawiono rozkład składowej stycznej i normalnej stanu naprężenia na powierzchni ściany wraz z analizą...
-
Vessel Energy Requirement Prediction from Acceleration Stage Towing Tests on Scale Models
PublicationOne of the most crucial tasks for naval architects is computing the energy required to meet the ship’s operational needs. When predicting a ship’s energy requirements, a series of hull resistance tests on a scale model vessel is carried out in constant speed stages, while the acceleration stage measurements are ignored. Another important factor in seakeeping analysis is the ship’s hydrodynamic added mass. The second law of dynamics...
-
Water-lubricated bearings of ship propeller shafts - problems, experimental tests and theoretical investigations
PublicationW pracy przedstawiono problemy związane z projektowaniem, montażem i ekspolatcją smarowanych wodą łożysk okrętowych wałów głównych.Przedstawiono wyniki prowadzonych prac badawczych ekperymntalnych i obliczeń.
-
Damage tests of the single shell ship fuel tank with additional elastic protective coating
PublicationWejście na mieliznę lub kolizja średniej wielkości np. kontenerowca może doprowadzić do zanieczyszczenia środowiska Morza Bałtyckiego paliwem uwolnionym z rozszczelnionych, jednoposzyciowych zbiorników dennych, a ilość tego paliwa może być znaczna. W związku z tym podjęto prace badawcze zmierzające do opracowania sposobu obniżenia ryzyka rozlewu paliwa w wypadku kolizji poprzez wprowadzenie drugiej bariery ochronnej. Idea pomysłu...
-
Application a laboratory stand for multi-symptoms tests for high cyclic fatigue of constructional material
PublicationThis paper describes a need of diagnostics present ship plants according to current technical state. In order to reach competent physical quantity describing fatigue of materials by congregated energy. This paper describes using some diagnostics methods (acoustic emission AE, vibration, thermovision, deformation) in order to definition fatigue state of construction material. The author tries to find correlation between measured...
-
Analysis and Comparison of Safety of Children and Adult Passenger in Car Based on Crash Tests Results
PublicationMost important features of the child seat were presented. There was made analysis of selected dynamic loads acting on mannequins heads during a collision. Comparison of loads acting on the kid in a child seat and the other passengers in a car is presented. In analysis of the results particular attention has been paid on the children's secure in a car. The phenomena of collision child's occipital bone with seat backrest was described....
-
Numerical tests of time-stepping schemes in the context of FEM for 6-field shell dynamics
PublicationThe paper deals with integration of dynamic equations of irregular shells performed with relatively long time steps. Numerical instability appearing often in this kind of analysis motivated the authors to present some studies based on numerical tests referring to convergence problems of finite element analysis as well the applied stability conditions. The analysis is carried out on simulations of shell dynamics with the where the...
-
Beam on elastic foundation with anticlastic curvature: Application to analysis of mode I fracture tests
PublicationA first order correction is proposed taking into account both interface elasticity and transverse anticlastic curvature of flexible substrate(s) in the DCB (and related tests). Adherends are represented by Kirchhoff-Love plates, and the interface by Winkler-type elastic foundation. Two functions are introduced, representing evolution of beam deflection along the sample midline and anticlastic curvature along the plate. A method...
-
Establishing Relationships between Parameters of the controlled Compaction Soil by Using Various In-Situ Tests
PublicationThe aim of research was evaluating reliable correlations between chosen soil parameters describing state of surface layers of soil. The paper presents site comparative tests based on the light falling weight deflectometer (LFWD), the static plate load tester (VSS), the dynamic probing light tester (DPL) and the bearing ratio tester (CBR in-situ) with relationships between soil state parameters. All featured in-situ...
-
Overflowing tests at the Polish DredgDikes research dike – stability of the dike surface against erosion
PublicationIn the project DredgDikes the different research dike embankments were tested with respect to overflowing water induced erosion. Therefore, flumes were installed on the land side embankments in which the effect of overflowing water on the vegetated surface was investigated. On the Polish DredgDikes research dike near Gdansk, Poland, two parallel flumes were installed and the surface of the dike made of different mixtures of...
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublicationOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
-
Dynamics analysis of footbridge mode shapes the s8 expressway on the basis of the results of in situ tests
PublicationNon-destructive diagnostics for structure may use dynamic measurements realized during vibrations of a facility induced by dynamic environmental impact, enforced by the use of inductors or impulse impact. Dynamic tests and the analysis were undertaken for a footbridge situated over the expressway S8. The studies in situ allowed for dynamic characteristics to be determined: frequency, shape modes and damping for respective frequency...
-
Applications of permeability, oedometer and direct shear tests to the sand mixed with waste tire crumb
PublicationThe amount of the used waste rubbers in the world has been increasing every year, and their utilization, become a major environmental problem worldwide. The present experimental work has been performed to investigate the influence of rubber inclusion on the behavior of a sand. Geotechnical properties of the sand, and sand with tire crumb at various ratios mixtures (0%, 2.5%, 7.5%, and 15%) were investigated through a series of...
-
Comparative study with magnetic techniques of P91 and 13HMF steels properties subjected to fatigue tests
PublicationWykonano badania porównawcze technikami magnetycznymi właściwości stali P91 i 13HMF poddanych testowi zmęczenia
-
Analysis and comparision of safety of children and adult passanger in car based on crash tests results
PublicationThis paper presents analysis and comparision of safety of children and adult passanger in car based on crash tests results. The car crash test with four dummies, including two car seats allowed a direct comparison of the security under the same conditions of children and passengers directly to the car seat. Analysis of acceleration and video from the test allows to understand the phenomena during the collision, the air bags influence,...
-
Evaluation of Mechanical Properties of Two-Stage Concrete and Conventional Concrete Using Nondestructive Tests
PublicationDifferent types of concrete mixtures are used as building materials. The manufacturing process of two-stage concrete (TSC) differs from that of conventional concrete. This study investigated conventional mechanical properties derive empirical relations for estimation of the mechanical parameters of TSC and conventional concrete mixtures. TSC was used to prepare 216 specimens and conventional concrete was used to prepare 108 specimens...
-
Ella4Life virtual assistant - user centered design strategy - evaluation following labolatory tests
PublicationIn the paper, we summarize the evaluation of Anne4Care system after laboratory tests. A group of end users, seniors over 55 years of age, rated a virtual assistant by completing a questionnaire. The objectives of the pilot evaluations are mainly to assess the feasibility, usability, acceptance and functionality of the system and the ability of the potential target user to use the system and receive valuable information from it...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublicationThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
The Method of Selecting the Interval of Functional Tests Taking into Account Economic Aspects and Legal Requirements
PublicationThe article discusses the problem of choosing the optimal frequency of functional tests, taking into account the reliability and law requirements, but also the impact of business aspects in the company. The subject of functional test interval is well described for purposes of the process industry. Unfortunately, this is not the case for the machinery safety functions with low demand mode. This is followed by a presentation of the...
-
Nanoindentation tests titanium alloy Ti-6Al-4V after interference laser treatment
PublicationThe study aimed was to assess selected mechanical properties of surface layers obtained after interference laser treatment – DLIL of titanium alloy Ti-6Al-4V used for implants. The samples were melted in still air at room temperature, for this purpose Nd:YAG laser was used, the number of laser shots was variable. Next, nanoindentation tests were performed, based on which Young’s modulus and nanohardness in the obtained surface...
-
Isothermal Calorimetry and Compressive Strength Tests of Mortar Specimens for Determination of Apparent Activation Energy
PublicationThe hydration process of cementitious materials involves a thermally activated reaction that depends on the composition of the mixture and the curing temperature. The main parameter affecting the temperature variation of cast-in-place concrete is the apparent activation energy, which can be used for the efficient prediction of the temperature evolution and maturity index of hardening concrete. This paper discusses two methods to...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Polyester sail technical woven fabric behaviour under uniaxial and biaxial tensile tests
PublicationThe paper is focused on the identification of mechanical properties of a sail technical woven fabric (yacht sailcloth polyester) style 480 AP with MTO (Medium Tempered Optimized) finish. The non-linear elastic behaviour of the fabric applied for sails is investigated under uniaxial and biaxial tensile tests. Comparison of non-linear elastic parameters with others polyester coated fabrics is made. This paper is intended to be an...
-
Znaczenie mocy testu statystycznego w analizie diagnostycznej okrętowego silnika o ZS
PublicationW artykule przedstawiono sposób interpretacji błędów pierwszego (α) i drugiego (β) rodzaju oraz wartości krytycznej Fkr rozkładu Fishera-Snedecora. Omówiono dwa sposoby weryfikacji istotności wpływu parametru wejściowego na wyjściowy. Przeanalizowano znaczenie mocy testu statystycznego M w diagnostyce parametrycznej okrętowych silników o ZS. Przeprowadzono analizę wpływu wartości poziomu istotności na wartość krytyczną statystyki...
-
New, fast and cheap prediction tests for BRCA1 gene mutations identification in clinical samples.
PublicationDespite significant progress in cancer therapy, cancer is still the second cause of mortality in the world. The necessity to make quick therapeutic decisions forces the development of procedures allowing to obtain a reliable result in a quick and unambiguous manner. Currently, detecting predictive mutations, including BRCA1, is the basis for effectively treating advanced breast cancer. Here, we present new insight on gene mutation...
-
On some problems in determining tensile parameters of concrete model from size effect tests
PublicationThe paper presents results of numerical simulations of size effect phenomenon in concrete specimens. The behaviour of in-plane geometrically similar notched and unnotched beams under three-point bending is investigated. In total 18 beams are analysed. Concrete beams of four different sizes and five different notch to depth ratios are simulated. Two methods are applied to describe cracks. First, an elasto-plastic constitutive law...
-
Timed rolling and rising tests in Duchenne muscular dystrophy ambulant boys: a feasibility study
PublicationBACKGROUND: Functional activities are extensively used in motor assessments of patients with Duchenne muscular dystrophy. The role of timed items has been reported as an early prognostic factor for disease progression. However, there are two functional activities that are not widely assessed in clinical practice among Duchenne muscular dystrophy patients: rolling and bed rising. This study aimed to investigate whether the 360-degree...
-
Estimation of concentration equilibrium constants of reaction between mutagenic HAA and antimutagenic cabbage phytochemicals based on data from Ames test
PublicationWykorzystano dane testu Amesa, przy pomocy którego oceniono antymutagenne właściwości fitokompleksu kapusty w stosunku do modelowych kancerogennych heterocyklicznych amin aromatycznych (HAA), do oszacowania stężeniowych stałych reakcji HAA z izotiocyjanianami występującymi w tym warzywie. Wyznaczone stężeniowe stałe reakcji wskazują na dużą stabilność powstałych koniugatów, a zatem sugerują, że kapusta może efektywnie chronić organizm...
-
Nowe testy diagnostyczne oparte o antygeny rekombinantowe Toxoplasma gondii do wykrywania oraz różnicowania fazy wczesnej i przewlekłej toksoplazmozy
PublicationToksoplazmoza jest jedną z najbardziej powszechnych chorób pasożytniczych człowieka i zwierząt stałocieplnych. Na świecie jedna trzecia ludzkiej populacji jest chronicznie zarażona Toxoplasma gondii. Mimo, iż choroba ta u zdrowych,dorosłych osób zazwyczaj ma charakter bezobjawowy, bardzo poważne objawy mogą wystąpić w przypadku wrodzonego zarażenia oraz u osób z niedoborem odporności. Ponadto, pomimo dokładnego poznania jej etiologii...
-
Corrosion resistance of sintered duplex stainless steels in the salt fog spray test
Publication -
Evaluating the performance of inverted pavement structure using the accelerated pavement test (APT)
Publication -
Assessment of the physical fitness of road cyclists in the step and ramp protocols of the incremental test
Publication -
<title>JTAG test system for RPC muon trigger in the CMS experiment</title>
Publication -
Efficiency rating of SG Diagnostics COVID-19 antigen rapid test kit
Publication -
Validation of a virtual test environment for C2X communication under radio jamming conditions
PublicationIn this paper, we propose a novel car-2-x communication security testing methodology in the physical layer of wireless systems. The approach is dedicated to automated testing of autonomous vehicles and it is essential for such complex systems operation, especially with regard to safety and security issues. It is based on scenario-driven testing in virtual and real test environments created from collected or simulated data. The...