Filters
total: 756
filtered: 672
Search results for: LIQUID-GAS FLOW MEASUREMENTS
-
Comparison of Two Methods for the Determination of Selected Pesticides in Honey and Honeybee Samples
PublicationDeveloped and validated analytical methods for the determination of a wide spectrum of pesticide residues in honey and honeybee samples after the modification of QuEChERS extraction in combination with gas chromatography–tandem quadrupole mass spectrometry (GC-MS/MS) and liquid chromatography–tandem quadrupole mass spectrometry (LC-MS/MS) were discussed and compared. The developed methods were evaluated regarding the utilized equipment...
-
Application of response surface methodology to optimize solid-phase microextraction procedure for chromatographic determination of aroma-active monoterpenes in berries
PublicationMost of scientific papers concern the qualitative or semi-quantitative analysis of aroma-active terpenes in liquid food matrices. Therefore, the procedure based on solid-phase microextraction and comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry for determination of monoterpenes in fresh berries was developed. The optimal extraction conditions using divinylbenzene-carboxen-polydimethylsiloxane fiber...
-
Endocrine Disrupting Compounds – Problems and Challenges
PublicationIn this chapter, information about some of the estrogenic compounds and their environmental fate and biological influence can be found. Special attention is paid to the review of the analytical approaches used at the stages of detection and determination of Endocrine Disrupting Compounds (EDCs) in the environmental samples. Also, a brief characterization of both cellular and non-cellular bioassays is presented. The discovery of...
-
On the Use of Selected 4th Generation Nuclear Reactors in Marine Power Plants
PublicationThis article provides a review of the possibility of using different types of reactors to power ships. The analyses were carried out for three different large vessels: a container ship, a liquid gas carrier and a bulk carrier. A novelty of this work is the analysis of the proposal to adapt marine power plants to ecological requirements in shipping by replacing the conventional propulsion system based on internal combustion engines...
-
Low energy elastic scattering of electrons from hexafluoropropene (C3F6)
PublicationWe present cross sections from a joint experimental and theoretical study on elastic electron scattering from hexafluoropropene (C3F6) in the gas phase. The experimental results, using low energy electron spectroscopy, were obtained at incident electron energies of 0.5, 1, 1.5, 2, 3, 4, 5, 6, 10, 12, 15 and 20 eV, for scattering angles ranging from 10°to 130°. The theoretical method used in the computation of the integral, momentum...
-
POM/EVA Blends with Future Utility in Fused Deposition Modeling
PublicationPolyoxymethylene (POM) is one of the most popular thermoplastic polymers used in the industry. Therefore, the interest in its potential applications in rapid prototyping is understandable. Nevertheless, its low dimensional stability causes the warping of 3D prints, limiting its applications. This research aimed to evaluate the effects of POM modification with ethylene-vinyl acetate (EVA) (2.5, 5.0, and 7.5 wt.%) on its processing...
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublicationA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
Thermophysical study of the binary mixtures of triethyl phosphate with N-methylformamide, N,N-dimethylformamide and N,N-dimethylacetamide – Experimental and theoretical approach
PublicationDensities at (293.15, 298.15, 303.15 and 308.15) K, and viscosities and ultrasonic velocities at 298.15 K of binary liquid mixtures of triethyl phosphate with N-methylformamide, N,N-dimethylformamide and N,N-dimethylacetamide have been measured over the entire range of composition at p = 0.1 MPa. From the experimental data, values of excess molar volume, excess isentropic compressibility, viscosity deviation and excess Gibbs energy...
-
Ruch wirowy wywoływany przez ultradźwięk w płynach z relaksacją
PublicationRozprawa doktorska poświęcona jest badaniu ruchu wirowego wywoływanego przez ultradźwięk w różnych modelach płynów z relaksacją. Ma ona charakter teoretyczny, jednak wykorzystanie uzyskanych dzięki niej wyników może przynieść lepsze zrozumienie ruchu wirowego wywoływanego przez siłę akustyczną. W I rozdziale rozprawy przedstawione zostały ogólne rozważania dotyczące akustyki nieliniowej. Rozdział II dotyczy ruchu wirowego wywoływanego...
-
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublicationIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
Radioactivity of drilling cuttings from shale resources of the Lower Paleozoic Baltic Basin, Poland
PublicationFractionated drilling wastes originating from shale gas exploration in the Baltic Basin in Pomerania were subjected to the measurements of mean activity concentrations of naturally occurring radioactive materials (NORMs).To better understand rock structure and texture, the X-ray diffraction analysis (XRD) and scanning electron microscopy(SEM) observation were used. To compare activity concentration of radionuclides in bulk wastes...
-
Waste Tyres Pyrolysis for Obtaining Limonene
PublicationThis review deals with the technologies of limonene production from waste tyre pyrolysis. Thermal decomposition is attractive for tackling the waste tyre disposal problem, as it enables both: energy to be recovered and limonene to be obtained. This material management recycling of tyres is environmentally more beneficial than the burning of all valuable products, including limonene. Given this recoverability of materials from waste...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Investigation of H2:CH4 plasma composition by means of spatially resolved optical spectroscopy
PublicationThe system based on spatially resolved optical emission spectroscopy dedicated for in situ diagnostics of plasma assisted CVD processes is presented in this paper. Measurement system coupled with chemical vapour deposition chamber by dedicated fiber-optic paths enables investigation of spatial distribution of species densities (Hx, H+, CH, CH+) during chemical vapour deposition process. Experiments were performed for a various...
-
Analysing the potential for application of the phase shift method in endoscopic examination of marine engines
PublicationThe article presents theoretical principles of image processing in digital endoscopy which makes use of a miniaturised spectral scanner “PhaseProbe” designed by General Inspection Technologies LP, the producer of the measuring videoendoscope Everest XLG3. The technology of optoelectronic 3D mapping of the examined surface, which consists in measuring the phase shift between the emitted and reflected light waves, is briefly described....
-
Influence of steam drying process on wood mechanical properties
PublicationResults of influence of gas-steam mixture drying process on mechanical properties of material are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process in a laboratory kiln especially arranged for that reason. Measurements of the global coefficient of elasticity and bending strength...
-
Investigations of Energy Conversion and Surface Effect for Laser-Illuminated Gold Nanorod Platforms
PublicationAchieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion...
-
The advanced monitoring as a key factor for appropriate optimization and control of full-scale activated sludge systems – case study Debogorze WWTP.
PublicationComputer simulation has become a helpful tool in wastewater treatment systems performance and effectiveness analysis. Advanced monitoring, by using appropriate software, enables to create a mathematical model of a real wastewater treatment plant (WWTP), run a simulation and subsequently interpret results under various conditions. An operation of WWTP is usually controlled by global parameters such as flow, solids retention time,...
-
Current trends in analytical strategies for the determination of polybrominated diphenyl ethers (PBDEs) in samples with different matrix compositions – Part 2: New approaches to PBDEs determination
PublicationHerein, we review the latest technical solutions for polybrominated diphenyl ethers (PBDEs) determination in samples with different matrix compositions, largely focusing on gas chromatography but also presenting some liquid chromatography–based solutions. Moreover, we discuss the use of diverse sample injection techniques while considering the advantages and disadvantages of each injection system in the context of PBDEs analysis....
-
Effect of selected ammonia escape inhibitors on carbon dioxide capture and utilization via calcium carbonate precipitation
PublicationCarbon dioxide was used to precipitate CaCO3 with CaCl2 solution in the presence of NH3 as a CO2 absorption promoter. Compounds that were previously indicated as inhibitors of ammonia escape during CO2 absorption were also added to the reaction mixture. Inorganic salts, i.e. ZnCl2, CuCl2, CoCl2, and organic substances, i.e. glycerol, ethylene glycol and triethanolamine were tested inhibitors in this work. A model post-distillation...
-
Indoor accelerated controlled corrosion degradation test of small- and large-scale specimens
PublicationThe work presented here is a part of a long-term project analysing the structural behaviour of ageing marine structures. An accelerated corrosion degradation set-up was developed to reproduce corroded marine structural specimens of different degrees of degradation, controlling various natural factors, i.e., temperature, oxygen content, salinity, and flow velocity. The nine stiffened plates of 1.2 m length and 30 small scale specimens...
-
Counting and tracking vehicles using acoustic vector sensors
PublicationA method is presented for counting vehicles and for determining their movement direction by means of acoustic vector sensor application. The assumptions of the method employing spatial distribution of sound intensity determined with the help of an integrated 3D intensity probe are discussed. The intensity probe developed by the authors was used for the experiments. The mode of operation of the algorithm is presented in conjunction...
-
Rating mathematical models for first-pass of tracer in pCT lung studies
PublicationThis paper presents a comparison of model based on the Gauss function and the most commonly used Gamma-variate model in perfusion computed tomography (pCT) lung studies. It also verifies whether used model affects value of blood volume parameter. Three mean concentration-time curves were created from actual pCT measurements: arterial input function, blood vessels in lungs and lung parenchyma. On the basis of these mean curves we...
-
Active management of equipment cooling in hoteling data centers
PublicationHoteling data centers are designated for housing computing and storage units of many, usually small customers, as opposed to traditional data centers supporting own computing and storage resources of a bigger company. One of the services to be provided to consumer’s equipment is cooling. Cooling in data centers is prevalently achieved by circulating air in computer room. Efficient cooling requires delivering cold air from central...
-
Local properties of organic coatings close to glass transition temperature
PublicationAcrylic coating applied on copper substrate has been investigated at different temperatures starting from the ambient one up to the level above the glass transition temperature. Its local topographic and electric properties have been examined with the atomic force microscopy (AFM) based approach including dc current mapping and local impedance spectroscopy. The local findings have been compared with the information from global...
-
Fault detection and diagnostics of complex dynamic systems using Gaussian Process Models - nuclear power plant case study
PublicationThe article examines the use of Gaussian Process Models to simulate the dynamic processes of a Pressurized Water nuclear Reactor for fault detection and diagnostics. The paper illustrates the potential of Gaussian Process Models as a tool for monitoring and predicting various fault conditions in Pressurized Water nuclear Reactor power plants, including reactor coolant flow and temperature variations, deviations from nominal working...
-
Channel Blockage and Flow Maldistribution during Unsteady Flow in a Model Microchannel Plate heat Exchanger
PublicationThis paper describes the problem of channel blockage as a result of flow maldistribution between the channels of a model mini channel plate heat exchanger consisting of one pass on each leg. Each leg of the heat exchanger contains 51 parallel and rectangular minichannels of four hydraulic diameters namely 461 μm, 571 μm, 750 μm and 823 μm. In addition, a more complex geometry has been investigated where for the sake of breaking...
-
A pilot study with flow mediated skin fluorescence: A novel device to assess microvascular endothelial function in coronary artery disease
PublicationBackground: Endothelial dysfunction is one of the earliest vascular manifestations in the pathogenesis of cardiovascular disease. Noninvasive, simple and inexpensive methods of endothelial function assessment are therefore needed. Methods: Microvascular endothelial function was assessed in coronary artery disease (CAD) patients by flow mediated skin fluorescence (FMSF), based on measurements of NADH fluorescence intensity during...
-
Application of nanofluids in thermal technologies
PublicationNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
Transport properties of aqueous ionic liquid microemulsions: influence of the anion type and presence of the cosurfactant
PublicationTransport properties, viz. specific conductivity, dynamic viscosity and apparent diffusion coefficients, were measured as a function of water content in aqueous ionic liquid microemulsions containing 1-butyl-3- methylimidazolium hexafluorophosphate, [BMIM][PF6] and bis(trifluoromethanesulphonyl)imide, [BMIM][Tf2N], stabilized by the nonionic surfactant TX-100, or its mixture with a cosurfactant, i.e. butanol. The investigation covered...
-
Experimental and theoretical studies on the Sulfamethazine-Urea and Sulfamethizole-Urea solid-liquid equilibria
PublicationThe miscibility of active pharmaceutical ingredients with excipients is an important aspect in pharmaceutical technology protocols. In this study, the differential scanning calorimetry (DSC) was used for Sulfamethazine-Urea (SI–U) and Sulfamethizole-Urea (SO–U) solid-liquid phase diagrams determination. Both sulfonamides form simple binary eutectics with Urea. The lack of new co-crystal phase formation was confirmed by inspection...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublicationIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Hydrogen production from ethanol In nitrogen microwave plasma At atmospheric pressure
PublicationHydrogen seems to be one of the most promising alternative energy sources. It is a renewable fuel as it could be produced from e.g. waste or bio-ethanol. Furthermore hydrogen is compatible with fuel cells and is environmentally clean. In contrast to conventional methods of hydrogen production such as water electrolysis or coal gasification we propose a method based on atmospheric pressure microwave plasma. In this paper we present...
-
Towards Computer-Aided Graphene Covered TiO2-Cu/(CuxOy) Composite Design for the Purpose of Photoinduced Hydrogen Evolution
PublicationIn search a hydrogen source, we synthesized TiO2-Cu-graphene composite photocatalyst for hydrogen evolution. The catalyst is a new and unique material as it consists of copper-decorated TiO2 particles covered tightly in graphene and obtained in a fluidized bed reactor. Both, reduction of copper from Cu(CH3COO) at the surface of TiO2 particles and covering of TiO2-Cu in graphene thin layer by Chemical Vapour Deposition (CVD) were...
-
Determination of t8/5 cooling times for underwater local dry welding of steel
PublicationKnowledge of thermal history is the basic condition for studying the structure - properties of welded joints. The determinant of thermal history is the thermal cycle, whose in-situ measurements are still a big challenge. Water as the welding environment complicates this issue even more. The article presents a method to determine an equation for calculating t8/5 cooling times for underwater gas metal arc welding of unalloyed steels...
-
Portable raman spectrometer for maritime security applications
PublicationThe fast identification of explosives, narcotics and other chemicals carried on board of ships or transported in containers to the harbors is an important problem of maritime security. Raman spectroscopy is widely used for fast identification of various chemicals. Continuous progress in the field of photonics has resulted in commercial availability of low-power compact Raman spectrometers which can be integrated into portable systems....
-
Opto-Electrochemical Sensing Device Based on Long-Period Grating Coated with Boron-Doped Diamond Thin Film
PublicationThe fabrication process of thin boron-doped nanocrystalline diamond (B-NCD) microelectrodes on fused silica single mode optical fiber cladding has been investigated. The B-NCD films were deposited on the fibers using Microwave Plasma Assisted Chemical Vapor Deposition (MW PA CVD) at glass substrate temperature of 475 ºC. We have obtained homogenous, continuous and polycrystalline surface morphology with high sp3 content in B-NCD...
-
Nanocrystalline diamond microelectrode on fused silica optical fibers for electrochemical and optical sensing
PublicationFabrication process of thin boron-doped nanocrystalline diamond (B-NCD) microelectrode on fused silica single mode optical fiber has been investigated. The B-NCD films were deposited on the fibers using Microwave Plasma Assisted Chemical Vapor Deposition (MW PA CVD) at glass substrate temperature of 475 ºC. We have obtained homogenous, continuous and polycrystalline surface morphology with the mean grain size in the range of 100-250...
-
Thermal dewetting as a method of surface modification of the gold thin films for surface plasmon resonance based sensor applications
PublicationHere, we report a quick and simple approach with low, optimized production costs to obtain surface plasmon resonance (SPR) based sensors fabricated through a time- and resource-effective method based on thermal dewetting of thin Au films. From the applicative point of view, the method of detection presented here should be easier to implement, since light transmission measurements seem to be much less challenging than light refractive...
-
Solid phase microextraction: state of the art, opportunities and applications
PublicationSolid phase microextraction is one of the most popular green techniques used for sample preparations in analytical chemistry. It is a simple, rapid, sensitive, and solvent-free technique. Since SPME was first introduced in the early 1990s, there has been an intensification of research in order to elaborate new methodical solutions in many research facilities around the world, which could increase the use of this technique. More...
-
Organotin Compounds: Environmental Fate and Analytics
PublicationFor more than 50 years, organotin compounds have been used in almost all sectors of industry. As a consequence, specific environmental compartments are affected by the emission of these xenobiotics. The emissions of organotin compounds into the environment from paints used in the shipbuilding industry for ship hull coating, and from the plant protection products are particularly significant.In 2001, the IMO introduced a global...
-
Searching for the primary metabolic alterations of polycystic ovary syndrome by application of the untargeted metabolomics approach
PublicationDespite a large number of studies, the pathogenesis of polycystic ovary syndrome (PCOS) still remains unexplained. In light of ambiguous observations reported in metabolomics, there is a need to carry out studies focusing on confirming the discriminating power of the proposed metabolomics biomarkers. Our research aimed to perform a validation study of metabolites detected in our previous study from serum samples, on the new set...
-
Stability of thin film diamond mirror for applications in interferometers under the short-time exposure on selected aggressive chemicals
PublicationIn presented study a thin boron-doped diamond film was proposed for application in the interferometry as a highly durable optical mirror. The unique properties of the diamond films, like high chemical stability and hardness, allow them to be used even in the chemically aggressive environment, where the commonly used silver mirrors can be susceptible to damage. The investigated nanodiamond layer was fabricated by uPE CVD method...
-
Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels
PublicationA dissimilar autogenous laser welded joint of AISI 430F (X12CrMoS17) martensitic stainless steel and AISI 304 (X5CrNi18-10) austenitic stainless steel was manufactured. The welded joint was examined by non-destructive visual testing and destructive testing by macro- and microscopic examination and hardness measurements. With reference to the ISO 13919-1 standard the welded joint was characterized by C level, due to the gas pores...
-
Estimation of groundwater recharge in a shallow sandy aquifer using unsaturated zone modeling and water table fluctuation method
PublicationQuantification of groundwater recharge is one of the most important issues in hydrogeology, especially in view of the ongoing changes in climate and land use. In this study, we use numerical models of 1D vertical flow in the vadose zone and the water table fluctuation (WTF) analysis to investigate local-scale recharge of a shallow sandy aquifer in the Brda outwash plain in northern Poland. We show that these two methods can be...
-
Influence of addition of carbon nanotubes on rheological properties of selected liquid lubricants - a computer simulation study
PublicationThis work is motivated by the improvement of anti-friction properties of lubricants by addition of CNTs proved experimentally in literature. In particular, a methodology is developed to compute the shear viscosity of liquid lubricants (Propylene Glycol) based on Molecular Dynamics simulation. Non-Equilibrium molecular dynamics (NEMD) approach is used with a reactive force field ReaxFF implemented in LAMMPS. The simulations are...
-
Spetiation of organic matter in Vertical Flow Constructed Wetlands
PublicationThe object of the research were VFCWs which are a component of biological treatment of two hybrid hydrophyte systems located in Wieszyno and Wiklino, close to Słupsk, Poland. The facilities that are subject to analyses are unified in terms of structure (filtration material, depth of the bed and time of operation), but they differ in organic matter load, amounting respectively to: 8.0 gCOD/m2day and 31.0 gCOD/m2day.The intensity...
-
Neural Modelling of Steam Turbine Control Stage
PublicationThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
Determination of benzodiazepines and Z-hypnotic drugs in whole blood samples by GC–MS/MS: Method development, validation and application
PublicationBenzodiazepines (BZDs) and Z-drugs are widely used as anxiolytics, sedative hypnotics, anticonvulsants and muscle relaxants. “Designer benzodiazepines” (DBZDs) are a new psychoactive substance class consisting of benzodiazepine derivatives that are not allowed for medical use and are known for being used recreationally. From a toxicologist standpoint, the huge number of such substances implicate a necessity for developing fast...
-
Machine-learning-based precise cost-efficient NO2 sensor calibration by means of time series matching and global data pre-processing
PublicationAir pollution remains a considerable contemporary challenge affecting life quality, the environment, and economic well-being. It encompasses an array of pollutants—gases, particulate matter, biological molecules—emanating from sources such as vehicle emissions, industrial activities, agriculture, and natural occurrences. Nitrogen dioxide (NO2), a harmful gas, is particularly abundant in densely populated urban areas. Given its...