Filters
total: 940
filtered: 840
-
Catalog
Chosen catalog filters
Search results for: temperature influence
-
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublicationThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
The analysis of temperature changes of the saliva traces left on the fur during laboratory rats social contacts
PublicationAutomatic analysis of complex rodent social be- havior, especially aggressive ones, is of important scientific interest. In this paper we analyze the properties of the data created as a result of aggressive rodent social behavior. Detec- tion of specific aggressive behaviors is based on the event of leaving traces of saliva on the fur of the attacked individual, which are clearly visible in the thermal imaging. The traces change...
-
High temperature oxidation behavior of SUS430 SOFC interconnects with Mn-Co spinel coating in air
PublicationIn this study, SUS430 alloy is evaluated for its high temperature corrosion properties as a possible material for interconnects of solid oxide fuel cells (SOFCs). Samples are coated with Mn-Co by commercial physical vapor deposition (PVD) process and oxidized in air for 1250 h at 800 °C. A dense cubic Mn-Co-Fe spinel layer is formed on the surface, showing great effect on corrosion reduction compared with the samples without coating....
-
Identification of damages in the inlet air duct of a diesel engine based on exhaust gas temperature measurements
PublicationThe temperature of the exhaust gas of a diesel piston engine, measured in the characteristic control sections of its thermo-flow system, can be a valuable source of diagnostic information about the technical condition of the elements limiting the working spaces thus separated, including the turbocharging system, but also its fuel supply system and replacement of the medium. In standard marine engine measurement systems equipped...
-
A Computational Analysis of the Aerodynamic and Aeromechanical Behavior of a Thermo-Well for Steam Temperature Measurement in a Steam Turbine
PublicationThe goal of the paper is twofold: firstly, it presents computational fluid dynamics analysis for finding maximum unsteady flow forces (and their frequencies) acting on a thermo-well for measuring steam temperature in a steam turbine control stage and secondly, it presents computational solid dynamics analysis of possibility of entry into resonance of the thermowell structure. There have been analyzed two cases of flow with changing...
-
Effect of Temperature on n-Tetradecane Emulsion in the Presence of Phospholipid DPPC and Enzyme Lipase or Phospholipase A2
Publication -
Circumferential temperature distribution during nucleate pool boiling outside smooth and modified horizontal tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych obwodowego rozkłądu temperatury w poziomych rurkach, ogrzewanych elektrycznie na których zachodzi wrzenie pęcherzykowe. Wykazano, że lokalne - w obszarze górnej tworzącej rurki, zastosowanie powłki porowatej prowadzi do wygładzenia rozkładu temperatury oraz obniżenia średniej temperatury ścianki.
-
Thermo-mechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
PublicationThermomechanical reclaiming of ground tire rubber (GTR) was performed at different temperatures (60, 120, and 180°C) using a co-rotating twin-screw extruder. Obtained samples were used in styrene-butadiene rubber (SBR) blends. As reference samples, SBR compounds containing untreated GTR were used. Curing characteristics, static and dynamic mechanical properties, and morphology of the obtained blends were determined. The results...
-
LABORATORY STAND FOR INVESTIGATIONS OF THE QUICK - CHANGING TEMPERATURE OF GAS FLOWING IN THE PISTON COMPRESSOR OUTLET CHANNEL
PublicationThis paper presents a laboratory stand, created as a part of work on the doctor dissertation, intended for investigation of heat and flow processes taking place in the Espholin H3S piston compressor outlet channel. The test stand elements and their configuration within the stand are described. Discussed are also problems connected with the quick-changing measurement technique, solutions which have been proposed so far in that technology...
-
Evaluation of porous ferritic Fe22Cr stainless steel for solid oxide fuel cells at high temperature
PublicationW pracy przedstawiono wyniki badań korozji stali Fe22Cr w wysokich temperaturach.
-
Determination of Moisture Content Profiles of Spruce Wood After High Temperature Process and Air Drying
PublicationThe results of moisture content of wood after the process of its drying under high temperature conditions and air drying are presented. Wood samples, namely spruce (Picea abies Karst.) from the northern part of Pomerania region in Poland, were subject of steam and air drying.The aim of experiments was to measure moisture content of wood in its cross sections using moisture meter WRD-100. The samples of thickness 70 mm and length...
-
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublicationPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
High Temperature Air/Steam Conversion of Biomass and Wastes Into Fuel Gas for Heat and Electricity Production
PublicationPaper present principle of high temperature air/staem gasification as well as some results of research using this technology for conversion of biomass and wastes into fuel gas.
-
Low temperature growth of diamond films on optical fibers using Linear Antenna CVD system
PublicationIt is not trivial to achieve a good quality diamond-coated fibre interface due to a large difference in the properties and composition of the diamond films (or use coating even) and the optical fibre material, i.e. fused silica. One of the biggest problems is the high temperature during the deposition which influences the optical fibre or optical fibre sensor structure (e.g. long-period gratings (LPG)). The greatest advantage of...
-
High Temperature Corrosion Evaluation of Porous Hastelloy X Alloy in Air and Humidified Hydrogen Atmospheres
PublicationIn this work a commercially available porous Hastelloy X alloy is characterized in terms of high temperature corrosion resistance. The alloy was oxidized in the temperature range from 500C to 900C in air and humidified hydrogen for 100 hours. Corrosion rates and porosity changes were measured. Microstructural characterization was performed using X-ray diffractometry and scanning electron microscopy. Results show that porous alloys...
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublicationThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublicationThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
Dissolution of Nb-doped hydroxyapatite prepared via low-temperature mechanochemical method: Spectroscopy studies
PublicationCalcium phosphate glass ceramics with nominal hydroxyapatite stoichiometry doped with niobium were synthesized using simple as well as low-temperature mechanochemical method and then in the form of compressed pellet were submitted to the static dissolution process in distilled water for one month. The results of structural analysis, performed mainly on the base of spectroscopic methods such as: infrared absorption spectroscopy,...
-
Experimental study of the fuel jet combustion in high temperature and low oxygen content exhaust gases
PublicationPrzeprowadzono badania eksperymentalne spalania pojedynczego strumienia paliwa gazowego. Paliwo podawano współosiowo do generowanych przez konwencjonalny palnik gazowy spalin o wysokiej temperaturze i niskiej zawartości tlenu. Badano wpływ zawartości tlenu w utleniaczu na widzialność płomienia i skład produktów spalania.
-
Surface morphology of PrBa2Cu3O7-ë single crystals after the long lasting high temperature reduction. .
PublicationZaprezentowano wyniki szczegółowej analizy powierzchni kryształów poddanych długotrwałej redukcji wysokotemperaturowej. Badania za pomocą skaningowej mikroskopii (SEM) wykazały obecność niestabilnych strukturalnie krystalitów powstałych w wyniku rozpadu powierzchni kryształów. Zanikanie zaindukowanego przy pomocy obróbki wysokotemperaturowej nadprzewodnictwa może być spowodowane migracją defektów podsieci Pr-Ba z wnętrza...
-
Thermodynamic interpretation and prediction of CO2 solubility in imidazolium ionic liquids based on regular solution theory
PublicationRegular solution theory (RST) is the most popular model for the interpretation of the interaction between CO2 and ionic liquids. In the present work, the parameters of this model were determined for the CO2 absorption in eleven imidazolium ionic liquids. The y-intercept (A) of the RST model for the investigated imidazolium liquids increases with increasing temperature whereas the slope (B) remains constant. The values of RST parameters...
-
Chemical structures, rheological and physical properties of biopolyols prepared via solvothermal liquefaction of Enteromorpha and Zostera marina biomass
PublicationIn this work, liquefied biomass from the Baltic Sea was used for the preparation of rigid polyurethane (PUR) foams. The biomass contained 10 wt% of Enteromorpha macroalgae and 90 wt% of Zostera marina seagrass characterized by a high content of cellulose. The influence of time, temperature and the type of solvent on the efficiency of the liquefaction process and properties of biopolyols was determined. Obtained materials were analyzed...
-
Effect of ground tire rubber on structural, mechanical and thermal properties of flexible polyurethane foams
PublicationFlexible polyurethane foams were modified with two kinds of ground tire rubber, untreated and thermo-mechanically reclaimed. A reclamation process was performed in auto-thermal conditions, which reduced the cost of the process and decreased the environmental impact of devulcanization (e.g., emission of gases). The reclamation process was carried out in a continuous manner using a co-rotating twin screw extruder. The foams were...
-
Fabrication of La-Doped Bi4Ti3O12 Ceramics
PublicationLa-modified Bi4Ti3O12 is a typical ferroelectric, piezoelectric and electro-optic material, having relatively low coercive field, low dielectric constant, high Curie temperature and high breakdown strength. Goal of the present research was to apply mixed oxide method for fabrication of BiTLax ceramics, study its chemical composition, crystalline structure and microstructure. The compound BiTLax for x=0, 0.25, 0.5, 0.75 ceramic...
-
Electronic and ionic relaxations in strontium-borate glass and glass-ceramics containing bismuth and vanadium oxides
PublicationThe topography, microstructure and electrical properties of strontium-borate glass and SBO glass containing bismuth and vanadium oxides, were studied. The structure was measured using X-ray diffraction (XRD), Energy Dispersive X-ray Spectrometer (EDS) and Scanning electron microscope (SEM) methods. The A.C. complex conductivity was investigated as a function of temperature and frequency. The influence of the quantity of bismuth...
-
Modelling study of flow boiling heat transfer of perspective fluids for refrigeration technology
PublicationThere is a gap of knowledge on flow boiling at high saturation temperatures and higher values of reduced pressure. Thus far, the in-house developed semi-empirical model for flow boiling and flow condensation showed a satisfactory accuracy for calculations for various refrigeration fluids for a wide scope of reduced pressures. This study presents results of calculations of heat transfer coefficient of perspective refrigeration fluids,...
-
Understanding the interactions between protein stabilizers and the peptide bond through the analysis of the volumetric and compressibility properties for the model systems
PublicationThis work confirms our earlier supposition, that volumetric and acoustic parameters for simple model proposed by us are directly related to stabilizing/destabilizing effect of osmolytes on proteins structure. The apparent molar volumes, V and the apparent molar isentropic compressions, KS,, of glycine and N,N,N –trimethylglycine (betaine) were determined from densities and speed of sound measurements in aqueous solution of N-methylacetamide...
-
Quantification of ultrafine airborne particulate matter generated by the wear of car brake materials
PublicationThe wear of car brakes is one of the main sources of airborne particulate matter in urban environments. Ultrafine wear particles are of special environmental interest since they can easily penetrate the human body through inhalation and cause various diseases. In the present study, the contribution of ultrafine particles to airborne particulate matter emitted from car brake materials was investigated under different friction conditions....
-
Preliminary study of linear viscoelasticity limits of cold recycled mixtures determined in Simple Performance Tester (SPT)
PublicationThe publication presents methodology developed for determination of linear viscoelasticity limits for cold recycled mixtures with cement and bituminous emulsion using Simple Performance Tester (SPT). Methodology was verified on reference materials (PCV and steel dummy specimens, cement concrete and asphalt concrete) to comply with elasticity and viscoelasticity theory. The developed methodology enabled determination of linear viscoelasticity...
-
Assessing Acute Toxicity and Endocrine Disruption Potential of Selected Packages Internal Layers Extracts
PublicationThe focus of the present study is migration of toxic substances from food contact materials and its actual influence on the health of the final consumer. Two food packagings (metal cans, TetraPack®) and five simulants medias (water, ethanol, acetic acid, DMSO, artificial saliva) were selected for simulation studies. For assessment of acute toxicity and endocrine disruption potential of extract samples, two biotests (Microtox® and...
-
Experimental study of the multi-disc negative brake for a hydraulic motor
PublicationThis paper describes the methodology for experimental testing of a multi-disc brake. The construction of this brake was also present. The brake is dedicated to hydraulic motors with a small working volume. Experimental tests were carried out on a brake with plates immersed in oil and, for comparison, tests were carried out on a dry brake. As a result of the tests, the permissible torque (load) that is able to transfer the brake...
-
Transformation of bimetallic Ag–Cu thin films into plasmonically active composite nanostructures
PublicationFormation of plasmonically active silver, copper and composite silver-copper nanostructures were studied in this paper. Metallic nanostructures were fabricated by thermal disintegration, so called dewetting, of the thin films in an argon atmosphere. The formation process of the nanostructures was in-situ observed by a novel method, based on resistance measurements. The influence of the material and thickness of the initial thin...
-
Microstructural Design of Ba0.5La0.5Co0.5Fe0.5O3 Perovskite Ceramics
PublicationBa0.5La0.5Co0.5Fe0.5O3 was synthesized in the solid-state reaction route. The influence of ball milling parameters (such as milling media size, angular velocity, and time), pelletizing pressure, and annealing parameters on the microstructure was studied. The grain size distribution and density or specific surface area changes were investigated in each approach while the individual parameters were changed. The evaluation of BLCF...
-
Electrical properties of Na2O-CaO-P2O5 glasses doped with SiO2 and Si3N4
PublicationSodium-calcium-phosphate glasses doped with SiO2 or Si3N4 having similar sodium ion concentrations were prepared by melt quenching. The conductivity was measured by impedance spectroscopy under nitrogen atmosphere in a wide frequency range (10 mHz–1 MHz) and wide temperature range (153–473 K). At 36.6 °C, DC conductivities of all glasses vary between 1.1 ∗ 10−12 and 8.9 ∗ 10−12 S cm−1 and have similar activation energies (between...
-
Właściwości elektryczne szkło-ceramiki zawierającej ferroelektryczną fazę BiV
PublicationKompozyty szklano - ceramiczne zawierające nanokryształy posiadają właściwości fizyczne, które nie są możliwe do uzyskania w innych materiałach. Dzięki możliwości wytworzenia szkło - ceramik posiadających kryształy o różnej wielkości (nano, mikro...) i różnorodnego typu, można w istotny sposób kontrolować właściwości elektryczne takich materiałów. Stała dielektryczna faz ferroelektrycznych jest bardzo wrażliwa na zmiany rozmiarów...
-
Application possibilities of the low-temperature repairs on creep-resistance turbine components from material GX23CrMoV12-1
Publication -
Temperature-Based Prediction of Joint Hardness in TIG Welding of Inconel 600, 625 and 718 Nickel Superalloys
Publication -
NICKEL-BASED LAYERED PEROVSKITE CATHODE MATERIALS FOR APPLICATION IN INTERMEDIATE-TEMPERATURE SOLID OXIDE FUEL CELLS
Publication -
<title>Correction of fiber optic ion sensor readings using a fiber optic temperature sensor</title>
Publication -
Short-term changes in thickness and temperature of the active layer in summer in the Kaffiøyra region, NW Spitsbergen, Svalbard
Publication -
Effect of high temperature exposure on the fatigue damage development of X10CrMoVNb9-1 steel for power plant pipes
Publication -
Effect of plasma nitriding process on the fatigue and high temperature corrosion resistance of Inconel 740H nickel alloy
Publication -
A Novel Method for High Temperature Fatigue Testing of Nickel Superalloy Turbine Blades with Additional NDT Diagnostics
Publication -
MITOGEN-ACTIVATED PROTEIN KINASE 4 impacts leaf development, temperature, and stomatal movement in hybrid aspen
Publication -
Automatic Adjustment of Integration Time in the NIR Camera for Calibrated Temperature Measurement during Inductive Heating Processes
Publication -
New devices to capture the temperature effect under dynamic compression and impact perforation of polymers, application to PMMA
Publication -
The Impact of Experimental Temperature and Water Level Manipulation on Carbon Dioxide Release in a Poor Fen in Northern Poland
Publication -
Investigation of the 0.4C-35Cr-45Ni-Nb Alloy after Service in High-Temperature Steam and Hydrocarbons Environment
PublicationThe paper presents the results of investigation of the 0.4C-35Cr-45Ni-Nb alloy, which operated in the cracked hydrocarbon feeds and dilution steam at 1125 C. The material originated from the pyrolytic furnace coil tubes, of which internal walls were in contact with the aforementioned medium, whereas the external walls were in contact with the flue gases. The examination included metallographic and mechanical tests on the material...
-
Prediction of cast-in-place concrete strength of the extradosed bridge deck based on temperature monitoring and numerical simulations
PublicationThe work is devoted to the implementation of a monitoring system for high performance concrete embedded in the span of an extradosed bridge deck using a modified maturity method augmented by numerical simulations conducted by the authors’ FEM code. The paper presents all research stages of bridge construction and considers the conclusions drawn from the results of laboratory tests, field measurements, and numerical calculations....
-
Improved Empirical Coefficients for Estimating Water Vapor Weighted Mean Temperature over Europe for GNSS Applications
PublicationDevelopment of the so-called global navigation satellite system (GNSS) meteorology is based on the possibility of determining a precipitable water vapor (PWV) from a GNSS zenith wet delay (ZWD). Conversion of ZWD to the PWV requires application of water vapor weighted mean temperature (Tm) measurements, which can be done using a surface temperature (Ts) and its linear dependency to the Tm. In this study we analyzed up to 24 years...