Filters
total: 1232
filtered: 1048
displaying 1000 best results Help
Search results for: technical requirements and operating range of photovoltaic power plants
-
Design Analysis of Micro Gas Turbines in Closed Cycles
PublicationThe problems faced by designers of micro-turbines are connected with a very small volume flow rate of working media which leads to small blades’ height and high rotor speed. In the case of gas turbines this limitation can be overcome by the application of a closed cycle with very low pressure at the compressor inlet (lower than atmospheric pressure). In this way we may apply a micro gas turbine unit of accepted efficiency to work...
-
Electrochemical Stability of Few-Layered Phosphorene Flakes on Boron-Doped Diamond: A Wide Potential Range of Studies in Aqueous Solutions
PublicationTwo-dimensional phosphorene has attracted great interest since its discovery as a result of its extraordinary properties. Two-dimensional single crystals of phosphorene can be useful for electrochemical (EC) sensing applications due to their enhanced surface-to-volume ratio. We proposed to investigate the electrochemical performance of phosphorene deposited directly on boron-doped diamond (BDD) electrodes. Noncovalent interaction...
-
Structure and electric transport properties of Ca-doped bulk PrBa2Cu3O7−δ
PublicationThe crystal structure and electric transport properties of Pr1-xCaxBa2Cu3O7- delta (x= 0.0, 0.1, 0.2, 0.5) bulk ceramic samples, prepared by the standard solid-state reaction in air, were examined by X-ray power diffraction, resistivity measurements and room temperature thermoelectric power determination. Ca atoms introduce additional holes to the system as well as structural defects. The orthorhombic-to-tetragonal structural...
-
Design of a test bench for determining the general characteristics of an internal combustion engine using a hydraulic power take-off system
PublicationThe paper presents a design of an engine test bench, which is used to determine the general characteristics of a truck engine using a power take-off (PTO). PTO drives a hydraulic system that generates a load on the engine at various points in its operation in the power range specified by the hydraulic system. The design allows for stationary and mobile tests with the test bench mounted on the truck, without any modification of...
-
Influence of operation temperature instability on gas sensor performance
PublicationGas sensors based on the semiconducting metal-oxides, such as SnO2, have been found to be very useful for detecting a wide range of gases. The reversible interactions of the gas with the surface of the sensing layer made of semiconducting metal-oxides are responsible for changes of sensor resistance which is usually used as a measure of sensor response. Semiconductor gas sensors are commercially available and applied in numerous...
-
Przyczółki mostowe wspomagane konstrukcjami z gruntu zbrojonego
PublicationW referacie przedstawiono syntezę prac związanych z oceną projektów przyczółków wykorzystujących odciążenie w postaci konstrukcji z gruntu zbrojonego geosyntetykami, realizowanych na drogach ekspresowych S3 i S7. W ramach przeprowadzonych audytów dokonano oceny zastosowanych rozwiązań szczegółowych i materiałów jak również obliczeń zamieszczonych w projektach. Zwrócono szczególną uwagę na przestrzenną prace bloków z gruntu zbrojonego...
-
Polityka i porządek prawny w polskiej energetyce na tle polityki Unii Europejskiej
PublicationW artykule przeanalizowano rozwój wspólnotowego rynku energii elektrycznej, polityk ę energetyczną Polski i UE, sytuację i działania Polski na wspólnotowym rynku energii elektrycznej, a następnie przeanalizowano nowe regulacje prawne dla współpracy rozproszonych źródeł energii elektrycznej i sieci inteligentnych z systemem krajowym, dla zwrotu energii odzyskiwanej z systemów elektromechanicznych do zasilającej...
-
Solutions of Power Electronics Converter for the Shore - to - Ship Power Systems
PublicationW artykule poruszono tematykę zasilania statków zacumowanych w porcie z lądowej sieci elektroenergetycznej poprzez wykorzystanie nowoczesnych konstrukcji przekształtników energoelektronicznych. Zaproponowano budowę sieci dystrybucyjnej prądu stałego, przewoźnej platformy zasilającej oraz zastosowanie zasobników energii
-
Analysis of inductive power transfer systems for variable air gap and voltage supply frequency
PublicationThe paper describes an IPT system, by which electrical energy may be transmitted through a large air gap between coils without electrical connection. It presents theoretical and simulation analysis of IPT, which allows for supplying a receiver in the conditions of slow, in relation to the dynamics of power supply, changes in dimension of the air gap. The influence of frequency characteristics of the system on the possible selection...
-
Assessment of the Current Potential of Hydropower for Water Damming in Poland in the Context of Energy Transformation
PublicationThe present paper indicates that hydropower, including small hydropower plants (SHPs), may play a very important role in Poland’s energy transformation in the near future. The development of SHPs may also increase water resources in the steppe Poland. Additionally, the aim of the present research is to conduct the PEST analysis of SHPs in Poland, taking into account the SHP potential. For the first time, maps showing the power...
-
Experimental bases for the rail track surface damage detection system
PublicationA diagnosis of rail surface is generally based on the classical method of direct assessment and track geometry measurements. Identification and qualification of inequality and damage on the surface rails is depend on the skills and experience person who conducting inspection. In times of increasing exploitation of railways, infrastructure managers decide to use systems supporting the assessment of technical condition of the railways....
-
Low-Power Receivers for Wireless Capacitive Coupling Transmission in 3-D-Integrated Massively Parallel CMOS Imager
PublicationThe paper presents pixel receivers for massively parallel transmission of video signal between capacitive coupled integrated circuits (ICs). The receivers meet the key requirements for massively parallel transmission, namely low-power consumption below a single μW, small area of less than 205 μm2, high sensitivity better than 160 mV, and good immunity to crosstalk. The receivers were implemented and measured in a 3-D IC (two face-to-face...
-
Comparing Apples and Oranges: A Mobile User Experience Study of iOS and Android Consumer Devices
PublicationWith the rapid development of wireless networks and the spread of broadband access around the world, the number of active mobile user devices continues to grow. Each year more and more terminals are released on the market, with the smartphone being the most popular among them. They include low-end, mid-range, and of course high-end devices, with top hardware specifications. They do vary in build quality, utilized type of material,...
-
Optimization of using recuperative braking energy on a double-track railway line
PublicationIn the introduction, possible ways of reusing energy from recuperation are presented. Next, the paper investigates the possibility of using regenerative braking in the range allowed by the detailed timetable by adopting the method of transferring the recovered electric energy directly to the catenary and immediate use of this energy by another train at the same power section. In the main part of the work, it is shown, that the...
-
Conducted emi propagation modelling in the wound components.
PublicationThe modelling of EMC behaviour of power electronics converters require specific models of devices which are adequate in a wide frequency range. A novel equivalent-circuit model of the inductor, suitable for EMC applications, has been developed and validated. The model can be used for the analyses of wounded components' behaviour in the conducted-EMI frequency range. The parameters of the proposed model can be evaluated based on...
-
Regulacja napięcia w sieci nN z rozproszonymi źródłami energii
PublicationPodłączanie rozproszonych źródeł energii do sieci energetycznych niskiego napięcia powoduje powstawanie problemów zmienności i niesymetrii napięcia, zwłaszcza w przypadku dużych odległości od transformatora zasilającego. W skrajnych przypadkach zachodzi konieczność redukcji mocy generowanej przez źródło podczas oddawaniu energii do sieci. Rozwiązaniem tego problemu jest zastosowanie energoelektronicznego regulatora napięcia składającego...
-
Architektura bezpieczeństwa systemu netBaltic
PublicationW artykule zaprezentowano założenia dotyczące zabezpieczania węzłów sieci realizowanej w ramach systemu netBaltic. Ze względu na dużą różnorodność rozważanych mechanizmów komunikacyjnych architektura bezpieczeństwa została podzielona na kilka elementów – infrastrukturę klucza publicznego (PKI), bezpieczeństwo systemowe węzłów, zabezpieczanie komunikacji w modelu samoorganizującej wieloskokowej sieci kratowej, a także sieci niewrażliwej...
-
THE METHOD OF MEASURING THE MEMBRANE COVER GEOMETRY USING LASER SCANNING AND SYNCHRONOUS PHOTOGRAMMETRY
PublicationThe authors present the experience and results of field studies carried out at the technical acceptance of Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland). An unusual design of covering made in the form of “Sheerfill I” technical fabric membrane required spanned in the form of sails, required the use of terrestrial laser scanning. Such approach allowed for the fast and accurate record of the surface of individual panels...
-
Wpływ właściwości czynników chłodniczych na straty egzergii w pompie ciepła (Influence of Refrigerants Properties for Exergy Losses in Heat Pump)
PublicationArtykuł poświęcony jest wpływowi występujących w pompie ciepła strat egzergii na jej efektywność energetyczną, a co za tym idzie koszty funkcjonowania instalacji. Autorzy prezentują tu metodologię obliczeniową, która może być zastosowana w procesach projektowania układów cieplno-przepływowych. Obliczenia zostały wykonane na podstawie typowego układu powietrznej pompy ciepła pracującej w klimacie środkowo-europejskim. Ponadto w...
-
NetBaltic System-Heterogenous Wireless Network for Maritime Communications
PublicationIn case of maritime communications, we observe a growing interest in deployment of multitask satellite-based solutions and development of new maritime-specific systems intended for improvements in safety of e-navigation. Analysis of different types of currently used maritime communication systems leads, however, to a conclusion that neither global and still very expensive satellite systems nor cheaper, but short-ranged transmission...
-
A low-voltage CMOS negative impedance converter for analogue filtering applications
PublicationLow-voltage high-frequency continuous-time filters are still required in many applications and are the subject of continuing research. There are many techniques to realize integrated filters, including OTA C, Opamp RC and MOSFET-C-Opamp. The latter two show high dynamic range at low supply voltage, but their frequency operating range is usually limited to several megahertz. Transconductance filters are dedicated to higher frequencies....
-
Frequency-Reconfigurable Hybrid SIW-Based Self-Diplexing Antenna Using Solid and Liquid Dielectric Loading
PublicationThis paper presents a novel frequencyreconfigurable self-diplexing antenna (SDA) utilizing a hybrid substrate-integrated waveguide (SIW). The antenna comprises a radiating slot, a feeding network, and a hybrid SIW cavity featuring half-mode circular and half-mode rectangular SIW structures. The unique feature of this antenna lies in its fine-tuning capability of each resonant frequency by inserting or injecting solid and liquid...
-
Magazynowanie energii elektrycznej i gospodarka wodorowa
PublicationW artykule dokonano przegl ą du aktualnych technologii magazynowania energii elektrycznej oraz zestawiono uzyskiwane parametry w aspekcie zastosowa ń w zasobnikach systemowych. Przedstawiono studium mo ż liwo ś ci magazynowania energii z odnawialnych ź róde ł energii (O Ź E) w zasobnikach akumulatorowych i elektrowniach szczytowo-pompowych w Polsce. Omówiono tak ż e mo ż liwo ś ci wykorzystania...
-
Możliwości sterowania mocą bierną elektrowni wiatrowej : Reactive power control methods in wind parks
PublicationReferat poświęcony jest zagadnieniu sterowania mocą bierną w elektrowniach wiatrowych. W pierwszej części referatu opisano tło problemu sterowania mocą bierną w parkach wiatrowych, podano powody, dla których moc bierna powinna podlegać regulacji oraz zarysowano metody, które mogą być do niej użyte. W celu sprawdzenia proponowanych metod kompensacji, zbudowano model matematyczny elektrowni wiatrowej, którego poszczególne elementy...
-
Design of an Autonomous IoT Node Powered by a Perovskite-Based Wave Energy Converter
PublicationThis paper presents the results of experimental research focused on wave energy harvesting and its conversion to power Internet of Things (IoT) devices. The harvesting and conversion process was performed using a wave energy converter (WEC) consisting of a lead zirconate titanate piezoelectric ceramic perovskite material and a prototype power electronic circuit. The designed WEC was considered as a power supply for an end node...
-
Liquid chromatography techniques for separation of flavonoids from Droseraceae
PublicationFlavonoids which are presented in insectivorous plants of the Droseraceae family have wide range of advantageous properties i.e. an antioxidant, anti-inflammatory and antimicrobial activities, antitumor activity was reported as well.The purpose of the research was to develop the most favourable conditions for liquid chromatographic separation and identification of myricetin and quercetin in extracts of insectivorous plants. In...
-
PARAMETRIC ANALYSIS OF THE EFFICIENCY OF THE COMBINED GAS-STEAM TURBINE UNIT OF A HYBRID CYCLE FOR THE FPSO VESSEL
PublicationA thermal diagram of the combined gas‒steam turbine unit of a hybrid cycle, which is an energy complex consisting of a base gas turbine engine with a steam turbine heat recovery circuit and a steam-injected gas turbine operating with overexpansion, is proposed. A mathematical model of a power plant has been developed, taking into consideration the features of thermodynamic processes of simple, binary, and steam-injected...
-
CFD analysis of fluid flow through the labyrinth seal
PublicationSteam and gas turbines are some of the fundamental means of power generation. The energy efficiency of the turbines, however, is not satisfactory. Ever since the start-up of the first turbine in the world, engineers have been striving for their increased efficiency. Multiple solutions to the problem of steam loss in an operating turbine are available. The use of seals is one of them. Empirical methods or numerical calculations...
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublicationIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
The distributed model predictive controller for the nuclear power plant turbo-generator set
PublicationTypically there are two main control loops with PI controllers operating at each turbo-generator set. In this paper a distributed model predictive controller DMPC, with local QDMC controllers for the turbine generator, is proposed instead of a typical PI controllers. The local QDMC controllers utilize step-response models for the controlled system components. These models parameters are determined based on the proposed black-box...
-
Metamaterial-Based Series-Fed Antenna with High Gain and Wideband Performance for Millimeter Wave Spectrum Applications
PublicationThis paper presents a high-gain, wideband series-fed antenna designed for 5G millimeter-wave (MMW) applications. The structure employs a substrate-integrated waveguide (SIW)-based power splitter and metamaterials (MMs). The power divider functions effectively at 27.5 GHz, exhibiting an impedance bandwidth from 26.9–28.6 GHz. The series-fed dipole is assembled on the SIW-based power splitter, incorporating four dipoles with varying...
-
Analysing the potential for application of the phase shift method in endoscopic examination of marine engines
PublicationThe article presents theoretical principles of image processing in digital endoscopy which makes use of a miniaturised spectral scanner “PhaseProbe” designed by General Inspection Technologies LP, the producer of the measuring videoendoscope Everest XLG3. The technology of optoelectronic 3D mapping of the examined surface, which consists in measuring the phase shift between the emitted and reflected light waves, is briefly described....
-
INTERLABORATORY COMPARISON OF THE ELECTROMAGNETIC EMISSION MEASUREMENTS USING FAR AND GTEM TEST SITES UP TO 1 GHz
PublicationElectromagnetic emission limiting is one of the basic requirements in the European Directive 2014/30/EU (EMC Directive). Manufacturers often use alternative methods of measurements to make preliminary verification of emission. This paper presents and analyzes problem with comparison between measurements in different test sites: FAR (Fully Anechoic Room) and GTEM (Gigahertz Transverse Electromagnetic cell). FAR is assumed as the...
-
Unravelling the role of electron–hole pair spin in exciton dissociation in squaraine-based organic solar cells by magneto-photocurrent measurements
PublicationA high absorption coefficient and narrow absorption bands in squaraine (SQ) dyes have resulted in rapidly growing interest in them as a donor material in photovoltaic devices. The exciton dissociation process in organic systems proceeds via a multistep mechanism where the electron–hole pairs (charge transfer states) involved in the current generation process determine the recombination losses and subsequently limit the overall...
-
Highly linear CMOS triode transconductor for VHF applications
PublicationA high-speed, fully balanced complementary-symmetry metal-oxide-semiconductor (CMOS) triode transconductor is presented. The proposed approach exploits a pseudo-differential-pair triode configuration with a simple adaptive circuit stabilising the drain-to-source voltages of metal-oxide-semiconductor (MOS) transistors. Since no additional active circuits (apart from the resistors made of the cut-off MOS devices) and no feedback...
-
Analysis of circular polarization antenna design trade‐offs using low‐cost EM‐driven multiobjective optimization
PublicationCircular polarization (CP) antennas are vital components of modern communication systems. Their design involves handling several requirements such as low reflection and axial ratio (AR) within the frequency range of interest. Small size is an important criterion for antenna mobility which is normally achieved as a by‐product of performance‐oriented modifications of the structure topology. In this work, multiobjective optimization...
-
Ideas of the New European Bauhaus (NEB) in architectural education
PublicationThe New European Bauhaus (NEB) is an interdisciplinary project initiated by the European Commission in 2020 [1], based on three values: sustainability, beauty and community (social inclusion). Its aim is to support the European Green Deal programme [2] by accelerating the transformation of various economic sectors, including construction, to improve the quality of people’s lives and protect the natural environment. Even though...
-
THE APPLICATION OF KALMAN FILTERING TO PREDICT VERTICAL RAIL AXIS DISPLACEMENTS OF THE OVERHEAD CRANE BEING A COMPONENT OF SEAPORT TRANSPORT STRUCTURE
PublicationAs the devices designed to transport materials, the overhead cranes should meet certain geometric requirements for their operation to be safe. The presently available geodetic equipment, in particular total stations, provides opportunities for precise 3D measurements of coordinates of the controlled points. These coordinates make a basis for correcting the height of crane runway axes. The paper presents a method to calculate position...
-
A current-controlled FET
PublicationA novel semiconductor device, viz., Horizontally-Split-Drain Current-Controlled Field-Effect Transistor (HSDCCFET) with two control electrodes is proposed in this works. For the sake of brevity, the device can be called a CCFET. Operating principle of the proposed transistor is based on one of the galvanomagnetic phenomena, the Biot-Savart-Laplace law and a Gradual Channel Detachment Effect (GCDE). The transistor is dedicated...
-
Size Reduction of Microwave Couplers by EM-Driven Optimization
PublicationThis work addresses simulation-driven design optimization of compact microwave couplers that explicitly aims at circuit footprint area reduction. The penalty function approach allows us to minimize the area of the circuit while ensuring a proper power division between the output ports and providing a sufficient bandwidth with respect to return loss and isolation around the operating frequency. Computational cost of the optimization...
-
Novel structure and EM-driven design of miniaturized microstrip rat-race coupler
PublicationIn this paper, a novel structure and design procedure of a miniaturized microstrip rat-race coupler (RRC) is described. Small size of the RRC is achieved by folding the transmission lines of the conventional circuit into its interior, as well as by implementation of the structure on three layers. The final size of the coupler realized for the operating frequency of 1 GHz is only 220 mm2, which gives over 95% footprint reduction...
-
Uniform sampling in constrained domains for low-cost surrogate modeling of antenna input characteristics
PublicationIn this letter, a design of experiments technique that permits uniform sampling in constrained domains is proposed. The discussed method is applied to generate training data for construction of fast replacement models (surrogates) of antenna input characteristics. The modeling process is design-oriented with the surrogate domain spanned by a set of reference designs optimized with respect to the performance figures and/or operating...
-
Assessment, optimisation and working fluid comparison of organic rankine cycle combined with negative CO2 gas power plant system
PublicationThis study aims to investigate the application of the Organic Rankine Cycle (ORC) as an alternative to low-pressure expansion in the negative CO2 power plant (nCO2PP). The reason for this study is that a detailed analysis of nCO2PP indicates a certain amount of waste heat present in the exhaust gas from the high-to-intermediate pressure gas turbine. Some of this energy can be used by the application of the expansion in a low-pressure...
-
A Five-Leg Three-Level Dual-Output Inverter
PublicationClassical 3-level dual-output inverter, 3-L DOI, involves two similar 3-level inverters that provides a pair of 3-phase output voltages with same or different frequencies from common input voltage source. Flexibility of either operation of the constituting inverters is evident in this DOI; but total duplication of power switches is a major drawback. State of the art coupled 3-L DOIs reduce this drawback by providing series-shared...
-
WYDZIELONE STRUKTURY W ZDECENTRALIZOWANYM SYSTEMIE ELEKTROENERGETYCZNYM
PublicationJednym z trendów, które są obserwowane we współczesnych systemach elektroenergetycznych jest stopniowa decentralizacja, będąca w dużej mierze efektem rosnącej roli generacji rozproszonej oraz ewolucją odbiorców w stronę prosumeryzmu. Rośnie rola lokalnego bilansowania i rodzi się zapotrzebowanie na powstawanie lokalnych struktur organizacyjnych, dążących do wydzielenia części infrastruktury elektroenergetycznej. Rodzi to nie tylko...
-
A novel dual-band rectifier circuit with enhanced bandwidth for RF energy harvesting applications
PublicationIn recent years, a rapid development of low-power sensor networks, enabling machine-to-machine communication in applications such as environmental monitoring, has been observed. Contemporary sensors are normally supplied by an external power source, typically in a form of a battery, which limits their lifespan and increases the maintenance costs. This problem can be addressed by harvesting and converting ambient RF energy into...
-
Testing sensitivity of A-type residual current devices to earth fault currents with harmonics
PublicationIn many applications, modern current-using equipment utilizes power electronic converters to control the consumed power and to adjust the motor speed. Such equipment is used both in industrial and domestic installations. A characteristic feature of the converters is producing distorted earth fault currents, which contain a wide spectrum of harmonics, including high-order harmonics. Nowadays, protection against electric shock in...
-
TEST FOR ASSESSING THE ENERGY EFFICIENCY OF VEHICLES WITH INTERNAL COMBUSTION ENGINES
PublicationThe most popular method for assessing the energy efficiency of vehicles is to compare the fuel consumption achieved in the conditions of selected approval test. Operating conditions are defined using the speed profiles, usually for only two categories: urban and extra-urban driving. Assessing the energy efficiency of vehicles should be performed using a more detailed classification of conditions. Presented results of comparison...
-
The semi-Markov model of the process of appearance of sea-going ship propupsion system ability and inability states in application to determining the reliablity of these systems
PublicationThe article presents possible application of the theory of semi-Markov processes in creating the eight-state model of the process of appearance of the propulsion systems ability and inability states on sea-going vessels performing transportation tasks in a relatively long operating time t (t → ∞). The model has been proved to be able to be successfully used for determining the reliability of the abovementioned systems. The probability...
-
Selection of C-Type Filters for Reactive Power Compensation and Filtration of Higher Harmonics Injected into the Transmission System by Arc Furnaces
PublicationThis article presents a method for selecting the elements of a C-type filter working with a conventional LC-type filter for compensating reactive power and filtering out higher harmonics generated by arc furnaces and ladle furnaces. The study was conducted in a steel mill supplied by a 110 kV transmission system, where higher harmonic currents and nonlinear loads were measured. A series of computer simulations were performed under...