Search
Filters
total: 8470
filtered: 5782
displaying 1000 best results Help
Search results for: ALB2 TYPE STRUCTURE
-
Traffic Type Influence on QoS Network Performance of Streaming Traffic Class
PublicationFeasibility study on QoS routing proved that the traffic type influence the network performance. The performance is defined here as a number of packets serviced by the network. In the paper additional element - buffers lengths used in service system was verified in terms of dependencies with routing performance. We present results obtained by simulation for many simulation scenarios. Analysis was done for two different network...
-
Wideband crossover structure with double ring resonators
PublicationThe structure of a four-port microstrip crossover is presented. The device is composed of two ring resonators, one circular and one built from meander lines, connected by four straight lines. The equivalent circuit model of the crossover is derived. The structure is designed on thin and flexible substrate to allow it to bend. The possibility of applying the device on curved surfaces is tested experimentally.
-
Tripping of F-type RCDs for sinusoidal residual current with superimposed smooth DC component
PublicationRecent trends in green energy development make that photovoltaics and electric vehicles are applied on an increasing scale. In both photovoltaic and electric vehicle charging installations, a significant value of DC component of the earth fault current may appear, which is a challenge, in particular, for commonly used residual current devices (RCDs). This paper presents results of the laboratory test on the operation of F-type...
-
Static and dynamic modelling blow- out type trauma of orbital wall
PublicationAuthors of the paper present initial results of finite element analysis of a blow-out type trauma of orbital wall. The research is liked with laboratory tests for the Young’s modulus of bones evaluation. In the finite element analysis the neighbourhood of orbital wall is modelled by triangle thin shell finite elements. In the paper results of nonlinear static and transient dynamic analysis (including damping) are compared. The...
-
Analysis of start energy of Stirling engine type alpha
PublicationThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
The Influence of Cement Type on Early Properties of Cold In-Place Recycled Mixtures
PublicationCold in-place recycling is a commonly used maintenance treatment in rehabilitation of low and medium volume roads in Poland. Typically, two types of binding agents are used—cement and bituminous emulsion (or foamed bitumen).Due to the harsh Polish climate with many freeze/thaw cycles and frequent occurrence of saturated conditions, the used amounts of cement are higher than those commonly used in warmer parts of Europe. While there...
-
Investigation of tracking systems properties in CAVE-type virtual reality systems
PublicationIn recent years, many scientific and industrial centers in the world developed a virtual reality systems or laboratories. One of the most advanced solutions are Immersive 3D Visualization Lab (I3DVL), a CAVE-type (Cave Automatic Virtual Environment) laboratory. It contains two CAVE-type installations: six-screen installation arranged in a form of a cube, and four-screen installation, a simplified version of the previous one. The...
-
The Boltzmann sequence-structure channel
PublicationWe rigorously study a channel that maps binary sequences to self-avoiding walks in the two-dimensional grid, inspired by a model of protein statistics. This channel, which we also call the Boltzmann sequence-structure channel, is characterized by a Boltzmann/Gibbs distribution with a free parameter corresponding to temperature. In our previous work, we verified experimentally that the channel capacity has a phase transition for...
-
Classifying type of vehicles on the basis of data extracted from audio signal characteristics
PublicationThe aim of this study is to find and optimize a feature vector for an automatic recognition of the type of vehicles, extracted form an audio signal. First, the influence of weather-based conditions of road surface on spectral characteristic of the audio signal recorded from a passing vehicle in close proximity to the road is discussed. Next, parameterization of the recorded audio signal is performed. For that purpose, the MIRtoolbox,...
-
SiC-based T-type modules for multi-pulse inverter with coupled inductors
PublicationThe paper presents SiC-based three-level T-type modules designed for a high-performance 30kVA DC/AC inverter operating at high frequency 85 kHz with low THD of the output voltage. This inverter system consists of two integrated parts. The first part is active and contains three parallelconnected three-phase T-type modules built with fast-switching SiC power transistors. The second, passive part of the system is a set of inductors...
-
Structure and paramagnetism in weakly correlated Y8Co5
PublicationWe report the basic physical properties of monoclinic Y8Co5 determined by means of magnetic susceptibility, electrical resistivity, and specific heat measurements. The crystal structure of Y8Co5 is monoclinic (P21/c) with lattice parameters a = 7.0582(6) Å, b = 7.2894(6) Å, c = 24.2234(19) Å, and β = 102.112(6)° as refined by using synchrotron powder x-ray diffraction data. The compound shows temperature independent paramagnetism...
-
Surface Structure of Components Created by Stereolitography
PublicationStereolithography is an additive rapid prototyping method. This method is based on the principle of solidifying a liquid photopolymer (resin) by laser radiation. Models obtained with this method are characterized by a specific surface structure called “stairstep effect”. It causes that, the surface should be processed by additional finishing (postprocessing). To minimize the additional machining process, the model should be set...
-
The inhibition effect of mad Honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution
PublicationThe inhibition effect of mad honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution was investigated by Tafel extrapolarisation (TP), electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). All the studied parameters exhibited good anti-corrosive properties against corrosion of 2007-type aluminium alloy in the test solution; the corrosion rates decreased with the increase...
-
Construction and development of IT Competence Centers - organizational structure
PublicationThe author presents the situation of the current units working between academic environment and business. the paper presents the possibility of using a dynamic structure to develop UCC.
-
Influence of process of straightening ship hull structure made of 316L stainless steel on corrosion resistance and mechanical properties
PublicationThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries, for architectural elements, and many others. The chemical composition of corrosion-resistant...
-
Experimental Tests Of Sandwich Beams In The Design Process Of GFRP Shell Footbridge Structure
PublicationThe paper includes selected aspects of the study to elaborate architectural, material and construction design of pedestrian footbridge spans made of composite materials. The considered footbridge is a sandwich-type shell structure. The cooperation of PET foam core with outer lining surfaces is crucial for its load bearing capacity. The paper is aimed to experimental investigation of sandwich beams subjected to bending loading....
-
Software modules and application layer's security structure of RSMAD
PublicationThe paper discusses the software modules of Radio System for Monitoring and Acquisition of Data from Traffic Enforcement Cameras (in short RSMAD). The structure of the application layer of the system has also been analysed in details, including: purpose, structure and principles of operation of software modules constituting this system. In addition, the paper presents and discusses the structure of security of application layer...
-
Why is the cubic structure preferred in newly formed ice?
PublicationMolecular dynamics was employed to explain the preference for the cubic structure in newly formed crystals of ice. The results showed that in supercooled liquid water the molecules connected by hydrogen bonds are more likely to adopt relative orientations similar to the ones characteristic for cubic ice. The observed preference for certain relative orientations of molecules in the hydrogen-bonded pairs results in the higher probability...
-
Influence of dopants on structure of polycrystalline bismuth niobate
PublicationBismuth niobate (BiNbO4) has attracted attention as a low-fired ceramics with promising microwave application potential. BiNbO4 ceramics was fabricated by mixed oxide method and sintered at temperature T<1000˚C. As the sintering aids a small amount of CuO oxide was used. The crystalline structure of the ceramic samples was examined by X-ray diffraction method at room temperature. The Rietveld refinement method was used for analysis...
-
The effect of package type on selected parameters of nutritional quality of the chilled stored red sauerkraut
PublicationThe key elements responsible for the quality of food are the technologies used toprocess raw materials and preserve obtained products. The aim of this paper wasto investigate the effect of package type (bags made from low density polyethylene[PE-LD] and the metallized polyethylene terephthalate [PET met/PE foil]) onselected quality parameters of the chilled stored red sauerkraut. Vegetables wereanalyzed before packaging and after...
-
A higher order transversely deformable shell-type spectral finite element for dynamic analysis of isotropic structures
PublicationThis paper deals with certain aspects related to the dynamic behaviour of isotropic shell-like structures analysed by the use of a higher order transversely deformable shell-type spectral finite element newly formulated and the approach known as the Time-domain Spectral Finite Element Method (TD-SFEM). Although recently this spectral approach is reported in the literature as a very powerful numerical tool used to solve various...
-
Urban Railway within the Linear Urban Structure: the Case Study of Perm, Russia
PublicationThe paper analyses the ten years’ experience of Perm to develop its system of the urban train trying to reveal the reasons for its modest performance and decline in the passenger traffic. The authors show how the Urban Train fits within the city urban structure and eval uate the potential of the Urban Train to become a feasible solution to the problem of connecting the periphery with the city centre. Furthermore,...
-
Superconducting properties and electronic structure of NaBi
PublicationResistivity, dc magnetization, and heat capacity measurements are reported for superconducting NaBi. Tc, the electronic contribution to the specific heat γ, the ΔCp/γTc ratio, and the Debye temperature are found to be 2.15 K, 3.4 mJ mol−1 K−2, 0.78, and 140 K respectively. The calculated electron–phonon coupling constant (λep = 0.62) implies that NaBi is a moderately coupled superconductor. The upper critical field and coherence...
-
The structure of demand and its economic consequences for urban transport
PublicationThe structure of demand for urban transport services, determined by the share of passengers entitled to free and reduced fares, is an important factor influencing its economic condition. The aim of this article is to present the results of research into the structure of demand for urban transport as well as its economic consequences. The article begins by considering the nature of the determinants and consequences of the public...
-
On the electronic structure of methyl butyrate and methyl valerate
PublicationWe present novel results of the analysis of the electronic structure of two aliphatic esters: methyl butyrate and methyl valerate. High-resolution photoabsorption spectra were collected and analyzed over the energy range 4.0–10.8 eV and showed for both the molecules not only a clear band of the HOMO to LUMO transition, but also vibronic structure associated with the first Rydberg-valence transition. Photoelectron spectra recorded...
-
Resonant Frequencies in Microstrip Structure with Omega Medium Substrate
PublicationThe paper presents the research on a rectangular microstrip structure with multilayer substrate containing dielectric and omega medium layers. The effect of pseudochiral medium layer location in the substrate and its thickness on the resonant frequency of the rectangular microstrip structure is investigated. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields. Utilizing the continuity...
-
Crystal growth of CsCl-type Yb0.24Sn0.76Ru
Publication -
New type T-Source inverter
Publication -
Personality Type and Neural Circulatory Control
Publication -
Conley type index and hamiltonian inclusions
PublicationOpisano definicję i własności indeksu dla zbiorów niezmienniczych wielowartościowego układu dynamicznego w nieskończenie-wymiarowej przestrzeni Hilberta. Podano nowe przykłady zastosowań do twierdzeń o istnieniu nietrywialnych rozwiązań okresowych układów hamiltonowskichz prawą stroną niegładką.
-
Taylor type predictor for pressure changes
PublicationCelem pracy jest ocena predykcji ciśnienia za pomocą rozwinięcia funkcji w szereg Taylora. Przewidywana wartość ciśnienia jest obliczana jako iloczyn wcześniejszych wartości mnożonych przez współczynniki wagowe wyznaczone w oparciu o szereg Taylora. Zaletą takiego podejścia jest możliwość analizy danych próbkowanych nierównomiernie. Podstawową wadą jest założenie, że ciśnienie jest dobrze aproksymowane przez wielomian niskiego...
-
Displacement control in PWK-type pumps
PublicationW referacie zaprezentowano konstrukcję mechanizmu sterowania wydajnością zastosowanego w pompach z rozrządem krzywkowym typu PWK. Przedstawiono wyniki wstępnych badań prototypu PWKZ-78 oraz komputerową analizę zjawisk zachodzących w komorze cylindrowej pompy.
-
Displacement control in PWK-type pumps
PublicationThe most important, strategic goal however is creation of the variable displacement version of the new pump PWK. Thanks to full discharge of it's commutation mechanism from hydrostatic forces the variable pump can be directly controlled by low-energy actuator like proportional electromagnet or stepping motor. It means that costly and complicated hydraulic servomechanism (applied in all present variable displacement pumps) is no...
-
Type of surface and tire rolling resistance
Publication...
-
Crystal growth of CsCl-type Yb0.24Sn0.76Ru
PublicationWzrost kryształów o stechiometrii Yb0.24Sn0.76Ru został przeprowadzony metodą topnikową. Kryształy poddano badaniom dyfrakcyjnym a także mikroskopii elektornowej. Yb0.24Sn0.76Ru krystalizuje w sześciennej strukturze typu chlorku cezu (CsCl).
-
Bernstein-type theorem for ϕ-Laplacian
PublicationIn this paper we obtain a solution to the second-order boundary value problem of the form \frac{d}{dt}\varPhi'(\dot{u})=f(t,u,\dot{u}), t\in [0,1], u\colon \mathbb {R}\to \mathbb {R} with Sturm–Liouville boundary conditions, where \varPhi\colon \mathbb {R}\to \mathbb {R} is a strictly convex, differentiable function and f\colon[0,1]\times \mathbb {R}\times \mathbb {R}\to \mathbb {R} is continuous and satisfies a suitable growth...
-
New type T-Source inverter
PublicationThis paper presents different topologies of voltage inverters with alternative input LC networks. The basic topology is known in the literature as a Z-source inverter (ZSI). Alternative passive networks were named by the authors as T-sources. T-source inverter has fewer reactive components in comparison to conventional Z-source inverter. The most significant advantage of the T-source inverter (TSI) is its use of a common voltage...
-
Design, modelling and analysis of a new type of piezoelectric motor. Multicell piezoelectric motor
PublicationThis paper describes a new type of piezoelectric motor. The results, obtained in the field of piezoelectric motors, have pointed out that these motors have potentially high possibilities in the future special applications. The research work presents the design, simulations and parameters of the piezoelectric motor with three rotation-mode actuators. The motor is characterized by a high power, relative high speed and torque. The...
-
Styrene Oxidation by Copper(II) Complexes Salen-Type Encapsulated into Nay Zeolite
PublicationThe copper(II) complex with a Schiff-base salen-type ligand has been encapsulated in the nanopores of a NaY zeolite by using two different methodologies, the flexible ligand and in situ complex preparation methods. The encapsulated and non-encapsulated copper(II) complexes were screened as catalysts for styrene oxidation by using TBHP as the oxygen source in acetonitrile solvent. Under the optimized conditions, the catalysts exhibited...
-
Taurine as a water structure breaker and protein stabilizer
PublicationThe enhancing effect on the water structure has been confirmed for most of the osmolytes exhibiting both stabilizing and destabilizing properties in regard to proteins. The presented work concerns osmolytes, which should be classified as “structure breaking” solutes: taurine and N,N,N-trimethyltaurine (TMT). Here, we combine FTIR spectroscopy, DSC calorimetry and DFT calculations to gain an insight into the interactions between...
-
DYNAMIC RESPONSE OF FORUM GDANSK STRUCTURE DUE TO RAIL TRAFFIC
PublicationThe paper presents the study of the impact of vibration induced by the movement of the railway rolling stock on the Forum Gdańsk structure. This object is currently under construction and is located over the railway tracks in the vicinity of the Gdańsk Główny and Gdańsk Śródmieście railway stations. The analysis covers the influence of vibrations on the structure itself and on the people within. The in situ measurements on existing...
-
Novel structure and design of compact UWB slot antenna
PublicationIn this paper, a novel structure of a compact UWB slot antenna is presented along with a simulation-driven design optimization algorithm for adjusting geometry parameters of the device. Our primary objective is to obtain small footprint of the structure while maintaining its acceptable electrical performance. It is achieved by introducing sufficiently large number of geometry degrees of freedom, including increased number of parameterized...
-
A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines
PublicationThe Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling...
-
Numerical FDM modelling of wave propagation in concrete structure
PublicationThe article presents application of finite difference method to damage detection and its size evaluation in concrete structure by elastic wave propagation method. The simulations of wave propagation in concrete structure were performed for six different damage scenarios. Damages were modelled as areas with changed material properties. Investigation focused on the influence of damage size on the energy of wave reflection. Presented...
-
Synthesis and crystal structure of ferrocenyl benzothiazole derivatives
PublicationNovel ferrocenyl-containing benzothiazole derivatives were synthesised in moderate yields by one-pot α-amidoalkylation of ferrocene. The reaction conditions were critically evaluated and the crystal structure of one of the amidoalkylated ferrocenes was resolved. Oxidation of the obtained compounds led to known fully aromatic 2-ferrocenylbenzothiazole in 81 % yield, which represents a convenient alternative to earlier methods utilizing...
-
Fatigue Performance of Double-Layered Asphalt Concrete Beams Reinforced with New Type of Geocomposites
PublicationThe reinforcement of asphalt layers with geosynthetics has been used for several decades, but proper evaluation of the influence of these materials on pavement fatigue life is still a challenging task. The presented study investigates a novel approach to the reinforcement of asphalt layers using a new type of geogrid composite, in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions is bonded...
-
Assessment of chemical‐crosslink‐assisted protein structure modeling in CASP13
Publication -
Advanced Macromodel Matrix Structure Cloning for FDTD
PublicationWe propose an improved macromodel-based techniquefor efficient analysis of the structures based on PhotonicCrystals (PhC). The technique involves a new structure of thecoupling matrix and advanced cloning of not only the macromodel matrices, but also the coupling matrices SE and SH.The method allows one to shorten considerably the preprocessingtime, the RAM usage and also the iterating speed of performingFDTD. With this...
-
Resonance in Rectangular Microstrip Structure Loaded with a Pseudochiral Medium Layer
PublicationA rectangular microstrip structure with multilayer substrate containing dielectric and pseudochiral medium layers is studied in this paper. The effect of Omega medium layer location in the substrate and its thickness on the complex resonant frequency of the rectangular microstrip structure is investigated.
-
Simulation of fluid structure interaction in a novel design of high pressure axial piston pump
PublicationA novel type of an axial, piston-driven high pressure hydraulic pump with variable capacity marks a significant improvement in the area of the hydraulic machinery design. Total discharge from hydrostatic forces eliminates a need for a servomechanism, thus simplifying operation, reducing weight and introducing the possibility of the pump displacement control by computer. PWK-type pumps, invented in the Gdansk University of Technology,...