Filters
total: 10217
filtered: 7998
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: LOW-TEMPERATURE PROPERTIES
-
The effect of high pressure and sub-zero temperature on total antioxidant capacity and the content of vitamin C, fatty acids and secondary products of lipid oxidation in human milk
PublicationThe objective of this study was to compare of the effects of high pressure of 193 MPa at - 20°C and Low Temperature Long Time pasteurization (LTLT or holder pasteurization, 62,5°C; 30 min) on the content and composition of fatty acids (FAs), concentrations of secondary products of lipid oxidation (TBARS), the total antioxidant capacity (TAC), total vitamin C and ascorbic acid (AsA) content in human milk. It was shown that no significant...
-
Cellulosic bionanocomposites based on acrylonitrile butadiene rubber and Cuscuta reflexa: adjusting structure-properties balance for higher performance
PublicationDesign and manufacture of cellulosic nanocomposites with acceptable performance is in the period of a transition from fantasy to reality. Typically, cellulosic nanofillers reveal poor compatibility with polymer matrices. Thus, adjusting the balance between structure and properties of cellulosic bionanocomposites by careful selection of parent ingredients is the first priority. Herein, we incorporated Cuscuta reflexa derived cellulose...
-
The effect of boron concentration on the electrical, morphological and optical properties of boron-doped nanocrystalline diamond sheets: Tuning the diamond-on-graphene vertical junction
PublicationIn this paper, the effect of boron doping on the electrical, morphological and structural properties of free-standing nanocrystalline diamond sheets (thickness ~ 1 μm) was investigated. For this purpose, we used diamond films delaminated from a mirror-polished tantalum substrate following a microwave plasma-assisted chemical vapor deposition process, each grown with a different [B]/[C] ratio (up to 20,000 ppm) in the gas phase....
-
Influence of Nitriding and Laser Remelting on Properties of Austenitic Stainless Steel Type X10CrNi18-8 and Cavitation Erosion Resistance
PublicationThe paper presents properties of surface layers. Surface layers were obtained by using low temperature glow–discharge nitriding process and laser remelting carried out on austenitic stainless steel type X10CrNi18-8. Investigations were done by using an Ultra Nanoindentation Tester (UNHT) in the Warsaw Institute of Fundamental Technological Research. The influence of the above mentioned...
-
Effect of slag coal ash and foamed glass on the mechanical properties of two-stage concrete
PublicationTwo-stage concrete (TSC) is known by various names such as colcrete, Polcrete, preplaced aggregate concrete and prepacked concrete. It is different from traditional concrete in two fundamental ways, namely method of construction and mix proportion. Two-stage concrete (TSC) is defined as firstly, coarse aggregates are placed into the formwork and grout is applied to fill in the between coarse aggregate particles voids. Secondly,...
-
The effect of the temperature change rate on determination of the criticalpitting temperature of stainless steels
PublicationPrzedstawiono wyniki badań wpływu szybkości zmian temperatury na wyznaczaną krytyczną temperaturę korozji wżerowej. Badania stali 316L przeprowadzono metodą termometrii cyklicznej. Stwierdzono, że zwiększenie szybkości zmian temperatury związane jest ze zwiększeniem wyznaczonej temperatury krytycznej. Zależność krytycznej temperatury korozji wżerowej od szybkości korozji ma charakter liniowy. Wartości krytycznej temperatury korozji...
-
Influence of B/N co-doping on electrical and photoluminescence properties of CVD grown homoepitaxial diamond films
PublicationBoron doped diamond (BDD) has great potential in electrical, and electrochemical sensing applications. The growth parameters, substrates, and synthesis method play a vital role in the preparation of semiconducting BDD to metallic BDD. Doping of other elements along with boron (B) into diamond demonstrated improved efficacy of B doping and exceptional properties. In the present study, B and nitrogen (N) co-doped diamond has been...
-
Evaluation of thermal cracking probability for asphalt concretes with high percentage of RAP
PublicationThe paper presents determination of the probability of thermal cracking of asphalt mixtures with different reclaimed asphalt pavement (RAP) content on the basis of laboratory tests and analytical evaluation using thermal stress development method. Probability was evaluated taking into consideration: the type and gradation of the mixture and the quality and content of RAP. Thermal stresses were determined using two models: elastic and...
-
Enhanced acceptor concentration, proton conductivity, and hydration in multicomponent rare‐earth ortho‐niobates
PublicationThe structural properties of (La0.2Nd0.2Sm0.2Gd0.2Eu0.2)1−xCaxNbO4−δ (x = 0–0.05) series have been studied by X-ray powder diffraction at room temperature. The thermal properties were investigated using thermogravimetry, from which the concentration of proton defects was determined. Additionally, dilatometry studies were carried out, from which the thermal expansion coefficients and the phase transition temperature between low-...
-
GAS SENSORS WITH TEMPERATURE MODULATION – AN OVERVIEW
PublicationAlthough different methods of improving semiconductor gas sensor properties have been proposed, a technique involving temperature modulation seems to be the most promising. Semiconductor gas sensors working with modulated temperature can be more stable and are more selective comparing with sensor working at one temperature. In this paper, various approaches to temperature modulation are reviewed.
-
Gas sampling system for matrix of semiconductor gas sensors
PublicationSemiconductor gas sensors are popular commercial sensors applied in numerous gas detection systems. They are reliable, small, rugged and inexpensive. However, there are a few problem limiting the wider use of such sensors. Semiconductor gas sensor usually exhibits a low selectivity, low repeatability, drift of response, strong temperature and moisture influence on sensor properties. Sample flow rate is one of the parameters that...
-
Analysis of the influence of external conditions on temperature readings in thermograms and adaptive adjustment of the measured temperature value
PublicationMeasuring human temperature is a crucial step in preventing the spread of diseases such as COVID-19. For the proper operation of an automatic body temperature measurement system throughout the year, it is necessary to consider outdoor conditions. In this paper, the effect of atmospheric factors on facial temperature readings using infrared thermography is investigated. A thorough analysis of the variation of facial temperature...
-
Synthesis, structure and properties of novel poly(hydroxyurethane)s obtained by non-isocyanate route
PublicationNon-isocyanate polyurethanes (NIPUs) can be synthesized by polyaddition of five-membered bis(cyclic carbonate)s and primary diamines. NIPUs are an alternative for the commonly used (in the form of foams, elastomers, coatings or fibers) in the industry polyurethanes obtained using toxic and moisture sensitive diisocyanates, polyols and low-molecular weight chain extenders. The main aim of this work was to synthesize non-isocyanate...
-
The effect of the temperature change rate on determination of the critical pitting temperature of stainless steels
Publication -
Taguchi sensors under temperature modulation
PublicationSemiconductor gas sensors are widely used in gas- analyzing applications for various gas species determination due to their low cost and possibility to detect number of different gases. However, one of the main problems with such sensors is their lack of selectivity. To overcome this issue different ap- proaches can be used. One of them is the operation with sensor temperature modulation combined with dedicated data process- ing...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
La 15 Nb x Ge 9 : a superstructure of the Mn 5 Si 3 structure type with interstitial Nb atoms
PublicationThe crystal structure and elementary properties of La15NbxGe9 are reported. Single-crystal X-ray diffraction,from a crystallite with only 0.12 Nb/formula unit, reveals that this compound, although transition metal deficient, crystallizes in a hexagonal “15-1-9”-like structure type, space group P63mc (no. 186) with lattice parameters a = b = 15.5017(2) Å, c = 6.9173(2) Å. The physical properties were examined by specific heat and resistivity...
-
High temperature proton conduction in LaSbO4
PublicationLanthanum orthoantimonate was synthesized using a solid‐state synthesis method. To enhance the possible protonic conductivity, samples with the addition of 1 mol% Ca in La‐site, were also prepared. The structure was studied by the means of X‐ray diffraction, which showed that both specimens were single phase. The materials crystallized in the space group P2 1 /n. Dilatometry revealed that material expands non‐linearly with the...
-
Numerical analysis of crack propagation in silicone nitride
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
INFLUENCE OF TEMPERATURE ON THE TYRE ROLLING RESISTANCE
PublicationTemperature is a very important factor controlling rolling resistance of road vehicle tyres. There are at least three different temperatures that may be considered as important factors controlling thermal conditions of the rolling tyre. The most common measure of the thermal conditions during tyre rolling is ambient air temperature. The other two are: pavement temperature and “tyre” temperature. Tyre temperature is the most difficult...
-
Tuning of the Electrochemical Properties of Transparent Fluorine-doped Tin Oxide Electrodes by Microwave Pulsed-plasma Polymerized Allylamine
PublicationWe report here the dry, one-step, and low-temperature modification of FTO surfaces using pulsed plasma polymerization of allylamine (PPAAm). PPAAm/FTO surfaces were characterized by X-ray photoelectron spectroscopy, spectroscopic ellipsometry, and contact angles to understand the morphological, structural, and optical properties. FTO were coated with a very thin layer of adherent cross-linked, pinhole-, and additive-free allylamine...
-
GTR/Thermoplastics Blends: How Do Interfacial Interactions Govern Processing and Physico-Mechanical Properties?
PublicationIn this work, GTR/thermoplastics blends (in ratio 50/50 and 75/25 wt.%) were prepared by melt-compounding in an internal mixer. During research, trans-polyoctenamer rubber (TOR), ethylene-vinyl acetate copolymer (EVA), ethylene-octene copolymer (EOC), and linear low-density polyethylene (LLDPE), were used in their thermoplastic phase. Microstructure and processing-performance property interrelationships of the studied materials...
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublicationUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
Utilization of ionic liquids for the enrichment of biogas
PublicationThis article discusses the dependence of biogas composition on organic feed material. High amounts of CO2 decrease the calorific value of biogas. Several technologies are reviewed which can be used to increase the calorific value. Special emphasis is laid on ionic liquids as a new absorbing material. ILs have a number of advantages due to their unique properties such as: low melting point, high thermal conductivity, no flammability,...
-
Field-induced suppression of charge density wave in GdNiC2
PublicationWe report the specific heat, magnetic, magnetotransport, and galvanomagnetic properties of polycrystalline GdNiC 2 . In the intermediate temperature region above T N = 20 K, we observe large negative magnetoresistance due to Zeeman splitting of the electronic bands and partial destruction of a charge density wave ground state. Our magnetoresistance and Hall measurements show that at low temperatures a magnetic field-induced transformation from...
-
Non-Contact Temperature Measurements Dataset
PublicationThe dataset titled The influence of the distance of the pyrometer from the surface of the radiating object on the accuracy of measurements contains temperature measurements using a selection of four commercially available pyrometers (CHY 314P, TM-F03B, TFA 31.1125 and AB-8855) as a function of the measuring distance. The dataset allows a comparison of the accuracy and measuring precision of the devices, which are very important...
-
Distributed wireless sensor for measuring humidity and temperature
PublicationHumidity and temperature monitoring is often required in industrial halls and laboratories and can be crucial, because many properties of electrical devices deteriorates under influence of these parameters. There are several useful commercial methods for measuring humidity and temperature, such as commercial hygrometers and humidity recorders. However, they do not allow data acquisition simultaneously from multiple sensors. This...
-
Generalized temperature dependence model for anammox process kinetics
PublicationTemperature is a key operational factor influencing the anammox process kinetics. In particular, at temperatures below 15 °C, the specific anammox activity (SAA) considerably decreases. This study aimed to describe the temperature dependence of the anammox process kinetics in the temperature range from 10 to 55 °C, including the specific characteristics of“cold anammox”. The commonly used Arrhenius and extended and modifiedRatkowsky...
-
Influence of temperature on the activity of anammox granular biomass.
PublicationThe aim of this study was to determine a short-term and long-term effect of temperature on the anammox rate and determination of temperature coefficients in the Arrhenius and Ratkowsky equations. The short-term effects of temperature on the anammox granular biomass were investigated in batch tests at ten different temperatures in the range of 10–55 °C. The maximum overall nitrogen removal rate of 1.3 gN gVSS−1·d−1 was observed...
-
Chemically reduced graphene oxide based aerogels - Insight on the surface and textural functionalities dependent on handling the synthesis factors
PublicationEfficient adjusting of reduced graphene oxide aerogels properties requires information about experimental factor-aerogel property relationship. In this work, the reduced graphene oxide aerogels surface and textural functionalities in relation to precursor concentration, gelation time and hydrogel freezing temperature were studied in detail, with the use of dynamic adsorption method of gaseous organic probes and experimental design....
-
Equivalent temperature for design of asphalt pavements in Poland
PublicationThe paper presents application of equivalent temperature for design of asphalt pavements. The calculation methods of equivalent temperature: the Shell method, the French method, the methods that use the AASHTO and the Asphalt Institute fatigue criteria were presented. The results of calculations of equivalent temperature for Polish climatic conditions were presented and discussed. It was shown that different asphalt pavement design...
-
Vertical Temperature Stratification of the Gulf of Gdansk Water
PublicationThe Baltic Sea is characterized by variable hydroacoustic conditions, which depend on hydrological conditions throughout the year. The temperature of the water is the factor that has the greatest impact on the changes in the speed of the sound in this basin. Even at a small depth, we can observe a large temperature gradient affecting the accuracy of the conducted research using hydroacoustic devices. A characteristic feature of...
-
Low-Dimensional Magnetic Semimetal Cr0.65Al1.35Se3
PublicationWhile exploring novel magnetic semiconductors, the new phase Cr0.65Al1.35Se3 was discovered and characterized by both structural and physical properties. Cr0.65Al1.35Se3 was found to crystallize into orthorhombic CrGeTe3-type structure with space group Pnma (no. 62). Vacancies and mixed occupancies were tested, and the results show that one of the 4c sites accommodates a mixture of Cr and Al atoms, while the other 4c site is fully...
-
Accurate Computation of IGBT Junction Temperature in PLECS
PublicationIn the article, a new method to improve the accuracy of the insulated-gate bipolar transistor (IGBT) junction temperature computations in the piecewise linear electrical circuit simulation (PLECS) software is proposed and described in detail. This method allows computing the IGBT junction temperature using a nonlinear compact thermal model of this device in PLECS. In the method, a nonlinear compact thermal model of the IGBT is...
-
Temperature distribution in laser-clad multi-layers
PublicationW pracy przedstawiono porownanie rezultatów numerycznej symulacji rozkładu temperatur w warstwach nakładanych laserowo z wynikami pomiarów doświadczalnych. Otrzymano bardzo dobrą zgodność wyników co pozwala wnioskować, że przedstawiony model numeryczny może służyć jako efektywne narzędzie wstępnego doboru parametrów procesu laserowego nakładania warstw.
-
Influence of temperature and nitrogen pressure on the test without active gases for high-temperature proton exchange membrane fuel cells
PublicationHigh-Temperature Proton-Exchange Membrane Fuel Cells (HT-PEMFCs) are a candidate for electrical energy supply devices in more and more applications. Most notably in the aeronautic industry. Before any use, an HT-PEMFC is preheated and after that supplied with its active gases. Only at this state, the diagnostics can be performed. A method of testing not requiring a complete start-up would be beneficial for many reasons. This article...
-
HIGH TEMPERATURE HEAT PUMPS – PERSPECTIVE HEATING SYSTEMS?
PublicationIn the paper presented are authors own concepts of high temperature compressor heat pumps for the utilisation of medium and low temperature sources of heat. Working fluids for use in high temperature heat pumps are discussed, as well as the criteria for their selection. Analyses are presented for the production of in the upper steam source at 130 °C. One-stage systems and cascade systems were analyzed. An analysis of the coefficient...
-
Temperature Sensors Based on Polymer Fiber Optic Interferometer
PublicationTemperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in...
-
Changes of Conformation in Albumin with Temperature by Molecular Dynamics Simulations
PublicationThis work presents the analysis of the conformation of albumin in the temperature range of 300K – 312K, i.e., in the physiological range. Using molecular dynamics simulations, we calculate values of the backbone and dihedral angles for this molecule. We analyze the global dynamic properties of albumin treated as a chain. In this range of temperature, we study parameters of the molecule and the conformational entropy derived from...
-
Distribution of Temperature in Multicomponent Multilayered Composites
Publication -
Temperature-dependent photoluminescence of polyazomethine films
Publication -
Optimal boiling temperature for ORC installation
PublicationW pracy przedstawiono oryinalne kryterium wyznaczania optymalnej temperatury odparowania czynnika w obiegu ORC w postaci równań analitycznych. Pokazano przykład obliczeniowy na bazie R134a, wody i etanolu.
-
High temperature corrosion resistance of porous hastelloy alloy
PublicationTo further understand the suitability of Ni-Cr-base alloy for solid oxide fuel cell (SOFC), a commercial Ni-Cr-Fe-Mo alloy, Hastelloy X was selected and evaluated for oxidation behaviour under high temperature conditions. HastelloyX was chosen due to its unusual resistance to oxidizing, reducing and neutral atmospheres. For long term stability of metal supported fuel cell, the corrosion resistance plays a vital role and must be...
-
Temperature Fiber-Optic Sensor with ZnO ALD Coating
PublicationThis study presents a microsphere-based fiber-optic sensor with a ZnO Atomic Layer Deposition (ALD) coating thickness of 100 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100 °C to 300 °C, with a 10 °C step. An interferometric signal is used to control whether the microstructure is whole. Spectrum shift of a reflected signal is used to ascertain changes in...
-
High temperature drying of beech with content of tension wood
PublicationThe presented artcle is focused on comparison of tension and normal wood of beech (Fagus sylvatica L.) in a high-temperature drying process. Samples of 26 mm thickness were selected from sapwood zone with different angle of growth rings. The article evaluated properties of tension and normal wood before and after drying process. Properties which are monitored were moisture, moisture gradients, covering tests, colour changes and...
-
Thin CVD diamond films - synthesis, properties, applications
PublicationThe basic model of diamond films growth, in the low pressure synthesis, deposition from the CVD gas phase, is the mixture of hydrocarbon gas in presence with activated hydrogen and its nucleation on the substrate as a result of pyrolysis reaction. It allows to cross the great energetic barrier between graphite and diamond. High pressure and temperature are replaced by change of electronic structure of atoms into gas precursors...
-
Nanofiltration-Assisted Concentration Processes of Phenolic Fractions and Carotenoids from Natural Food Matrices
PublicationIn new food formulations, carotenoids and phenolic compounds are likely to be the most sought after food ingredients according to their bioactivity, nutraceutical, nutritional value, and compatibility properties once incorporated into food formulations. Such solutes are naturally present in many plant-based sources, and some portions are directly consumed when enriching food products and formulations; however, some portions, which...
-
Temperature measurement using NIR camera with automatic adjustment of integration time for monitoring high-temperature industrial processes
Publication -
Temperature distribution of supercapacitors prepared by various technologies
PublicationSupercapacitors, also known by different names such as electrostatic double-layer capacitors (EDLCs) or ultra-capacitors, are electrical storage devices still in development. These devices require fast and reliable methods of assessing their state-of-health. Thermographic imaging is a method which can be applied with this aim due to its popularity, and the high negative impact of overheating on a supercapacitor’s parameters. Moreover,...
-
High temperature corrosion evaluation and lifetime prediction of porous Fe22Cr stainless steel in air in temperature range 700–900 °C
PublicationThis work describes a high temperature corrosion kinetics study of ~30% porous Fe22Cr alloys. The surface area of the alloy (~0.02 m2 g-1) has been determined by tomographic microscopy. The weight gain of the alloys was studied by isothermal thermogravimetry in the air for 100 hours at 700 - 900 °C. Breakaway oxidation was observed after oxidation at 850 °C (~100 hours) and 900 °C (~30 hours). The lifetime prediction shows the...