Filters
total: 357
filtered: 338
Search results for: TRAVELING FAULT ARC
-
Performance analysis of power swing blocking feature in ABB 670 series impedance relays
PublicationThis paper presents test results of a distance protection’s PSD power swing detection feature in ABB 670 series relays. A RED670 relay was tested, which is part of the hydroelectric set protection in Żarnowiec Pumped Storage Plant. The power swing blocking feature’s performance was analysed on the basis of the results of object tests made with an Omicron digital tester. Also presented are simulation results that illustrate the...
-
SELECTION OF DIAGNOSTIC FUNCTIONS IN A WHEELED TRACTOR
PublicationIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
Weldability of S500MC Steel in Underwater Conditions
PublicationWet welding with the use of covered electrodes is one of the methods of underwater welding. This method is the oldest, the most economic and the most versatile. The main difficulties during underwater wet welding are: high cooling rates of the joint, the presence of hydrogen in the arc area and formation of hard martensitic structure in the weld. These phenomena are often accompanied by porosity of welds and large number of spatters,...
-
Shaping of the turnout diverging track with variable curvature sections
PublicationThe paper presents an analytical method of shaping the turnout diverging railroad track with variable curvature segments on its length, which in an evident way distinguished it from a typical solution, made up of a single circular arc with no transition curves. Two separate causes including a linear and a nonlinear curvature one in the form of a polynomial have been examined. The obtained solutions of the problem have a universal...
-
EHV transmission lines wires location on line operation issues - case studies
PublicationTransmission lines towers construction affects the line parameters and influences on its operation in the future. Misguided design of the tower can lead to serious problems such as overvoltages, electric arc extinction difficulties, voltage asymmetry, resonance phenomena or increasing of magnetic field near the line. The paper points out those threats on example of 400 kV double circuit overhead transmission line with shunt reactors....
-
Możliwości wydłużania krzywych przejściowych w układach geometrycznych torów
PublicationW pracy przedstawiono analizę problemu wydłużania krzywych przejściowych, wykorzystując do tego celu analityczną metodę projektowania. Podstawę analizy stanowiły obliczenia numeryczne przeprowadzone dla zestawu parametrów charakteryzujących standardowy układ geometryczny: krzywa przejściowa – łuk kołowy – krzywa przejściowa (w wersji niesymetrycznej). Ocenie poddano różnice rzędnych poziomych układu istniejącego oraz układu z...
-
Enhancing seismic performance of rigid and semi-rigid connections equipped with SMA bolts incorporating nonlinear soil-structure interaction
PublicationNowadays, using smart connections can improve the performance of buildings with some recentering features that are from the superelastic behavior of Shape Memory Alloys (SMAs). It seems that there is different rigidity between the designed connection and the real one in Steel Moment-Resisting Frames (SMRFs), which can be considered as a problematic issue due to the importance of connections in seismic performance assessment. This...
-
Redukcja czasu analizy MZP przez ograniczenie rozmiaru rozwiązania
PublicationAnaliza drzew niezdatności jest uznaną metodą analizy bezpieczeństwa systemów. Notacja ECSDM pozwala definiować zależności czasowe między zdarzeniami drzewa oraz przeanalizować je w celu określenia zależności pomiędzy zdarzeniami z Minimalnych Zbiorów Przyczyn (MZP). Dzięki wprowadzeniu klasyfikacji zdarzeń z MZP można wyodrębnić zależności czasowe istotne dla zapobiegania wywoływania hazardu przez konkretny MZP. Pozostałe zależności...
-
The effect of current delay angle on tripping of residual current devices
PublicationPower electronics converters applied in domestic or similar installations may utilize current delay (phase) angle control to change the level of transferred power. Due to application of such types of converters, earth fault current in the installation may be strongly distorted. The current distortion level depends on a value of current delay angle. This delay angle also influences the tripping threshold of residual current devices....
-
Polyarmonic model of synchronous generator for analysis of autonomous power generation systems
PublicationAbstract: This paper presents the polyharmonic modelling of synchronous generator (SG) in machine variables. The simple geometry and windings physical layout has been used for inductance calculations of a salient-pole SG. The main advantage of this model is the ease of describing an autonomous power generation system (APGS) in terms of its topology and thus providing effective analysis at the static and dynamic states, both for...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublicationThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
The application of nonlinear curvature sections in the turnout diverging track
PublicationThe paper presents the analytical method of modelling the diverging track of railway turnout with nonlinear curvature sections. These sections were used for smoothing the graph of curvature in the extreme areas of turnout. The problem of the curvature distribution was identified with the use of differential equations. The resulting solutions are of universal nature for example the ability of assuming any values of curvature at...
-
Effect of hybrid modification by ceramic layer formation in MAO process and laser remelting on the structure of titanium bio-alloy Ti13Nb13Zr
PublicationTo improve the biological properties of titanium alloy Ti13Nb13Zr, hybrid modifications involving micro-arc oxidation (MAO) and Nd: YAG laser remelting were carried out in two combinations. The first consisted of laser modification before the production of the ceramic layer by the micro-arc oxidation process, and the second combination involved Nd: YAG laser modification after the MAO process. The creation of developed surface...
-
Risk Analysis by a Probabilistic Model of the Measurement Process
PublicationThe aim of the article is presentation of the testing methodology and results of examination the probabilistic model of the measurement process. The case study concerns the determination of the risk of an incorrect decision in the assessment of the compliance of products by measurement. Measurand is characterized by the generalized Rayleigh distribution. The model of the meas-urement process was tested in parallel mode by six risk...
-
Impact of configuration of earth continuity conductor on induced sheath voltages in power cables
PublicationIn high voltage power cable systems a problem of induced sheath voltages exist. Due to these voltages electric shock and damage of non-metallic outer sheath of the cables may occur. Exposure to voltage of the outer sheath may be very high in case of earth fault with high value of earth current. In order to reduce induced sheath voltages an earth continuity conductor (conductors) along power cables is applied. Configuration of this...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublicationThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Broken rotor bar impact on sensorless control of induction machine
PublicationThe aim of the research is analysis of the sensorless control system of induction machine with broken rotor for diagnostic purposes. Increasing popularity of sensorless controlled variable speed drives requires research in area of reliability, range of stable operation, fault symptoms and application of diagnosis methods. T transformation (Cunha et al.,2003) used for conversion of instantaneous rotor currents electrical circuit...
-
Integrating heterogeneous systems with high-dependability requirements by means of web services
PublicationWeb services are commonly used on boundaries of heterogeneous components in Service Oriented Architecture (SOA) as they provide a universal communication channel not bound to any particular programming language or run-time platform. This paper describes how web services can be used to integrate heterogeneous systems which serve purposes requiring high dependability, reliability and availability. Examples of such systems include...
-
Analytical design method of reverse curves
PublicationThe paper deals with a new approach relating to the design of the region of railway track direction alteration adapted to Mobile Satellite Measurements technique. The method may be particularly useful in situations when both the straights of the route directions cannot be connected in an elementary way using a circular arc with transition curves; this also refers to the application of a compound curve. Thus the only solution becomes...
-
DETERMINATION OF SP3 FRACTION IN ta-C COATING USING XPS AND RAMAN SPECTROSCOPY
PublicationThe paper presents results of studies on the structure of tetrahedral amorphous carbon films (ta-C) with a thickness in the range from 20 to 280 nm, deposited using pulsed vacuum arc technique with an electromagnetic Venetian blind plasma filter. The results of the phase structure analysis, obtained using visible Raman spectroscopy and UV Raman spectroscopy methods, showed a strong dependence of the results on the presence, on...
-
Detailed studies of superconducting properties of Y2Pd1.25Ge2.75
PublicationWe report a successful synthesis of a high-purity intermetallic germanide Y2Pd1.25Ge2.75, crystallizing in the disordered variant of the AlB2-type structure. A single-phase sample was obtained via arc-melting by deliberately tuning the composition out of the ideal 2:1:3 ratio. Specific heat, electrical resistivity and magnetization measurements show that the compound is a weakly-coupled (λ e-p = 0.58) type-II superconductor with...
-
Synthesis, structure and physical properties of new intermetallic spin glass-like compounds RE2PdGe3 (RE = Tb and Dy)
PublicationNew intermetallic compounds Tb2Pd1.25Ge2.75 and Dy2Pd1.25Ge2.75 have been synthesized using the arc-melting method. The crystallographic structure and magnetic, electronic transport, and thermal properties are reported. The crystal structure obtained from powder x-ray diffraction analysis suggests that these compounds crystallize in the AlB2-type structure (space group P6/mmm, no. 191) with lattice parameters a = 4.228 53(5)/4.230 54...
-
Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study
PublicationTwo types of the weld joint of Inconel 617 alloy were produced using gas tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) processes with ERNiCrCoMo-1 filler metal and ENiCrCoMo-1 electrode, respectively. The weld metal showed the segregation of the principle alloying elements like Mo and Cr along the inter-dendritic spaces, triggering the formation of secondary phases. The microstructure characterization of the...
-
Novel approach to modeling spectral-domain optical coherence tomography with Monte Carlo method
PublicationNumerical modeling Optical Coherence Tomography (OCT) systems is needed for optical setup optimization, development of new signal processing methods and assessment of impact of different physical phenomena inside the sample on OCT signal. The Monte Carlo method has been often used for modeling Optical Coherence Tomography, as it is a well established tool for simulating light propagation in scattering media. However, in this method...
-
The possibility of estimating the height of the ionospheric inhomogeneities based on TEC variations maps obtained from dense GPS network
PublicationA state of the ionosphere can be effectively studied using electromagnetic signals received from global navigation satellite systems (GNSS). Utilization of the dual frequency observations allows estimating values of the total electron content (TEC). They can be used for a number of scientific studies such as detection and monitoring of traveling ionospheric disturbances or plasma bubbles. Moreover, maps of TEC variations allow...
-
Kernel PCA in Application to Leakage Detection in Drinking Water Distribution System
PublicationMonitoring plays an important role in advanced control of complex dynamic systems. Precise information about system's behaviour, including faults detection, enables efficient control. Proposed method- Kernel Principal Component Analysis (KPCA), a representative of machine learning, skilfully takes full advantage of the well known PCA method and extends its application to nonlinear case. The paper explains the general idea of KPCA...
-
Earth wires currents calculation by tableau analysis
PublicationThe paper presents a new method to compute a phase-to-earth fault current distribution in overhead transmission line. The method is based on the tableau analysis of an unbalanced, multi-wire model of a transmission line. It allows for the calculation of current distribution in overhead earth wires along the transmission line. Additionally, it may be used to calculate currents in a tower’s earthing system as well as voltages over...
-
Mitigation of Fake Data Content Poisoning Attacks in NDN via Blockchain
PublicationAbstract—Information-centric networks struggle with content poisoning attacks (CPAs), especially their stronger form called Fake Data CPA, in which an intruder publisher uploads content signed with stolen credentials. Following an existing graphinfection based approach leveraging the constrained time when stolen credentials are useful, we design a blockchain-based mitigation scheme for Named Data Networking architectures. We postulate...
-
Tripping of F-type RCDs for sinusoidal residual current with superimposed smooth DC component
PublicationRecent trends in green energy development make that photovoltaics and electric vehicles are applied on an increasing scale. In both photovoltaic and electric vehicle charging installations, a significant value of DC component of the earth fault current may appear, which is a challenge, in particular, for commonly used residual current devices (RCDs). This paper presents results of the laboratory test on the operation of F-type...
-
Detection of inter-turn faults in transformer winding using the capacitor discharge method
PublicationThe paper presents results of an analysis of inter-turn fault effects on the voltage and current waveforms of a capacitor discharge through transformer windings. The research was conducted in the frame of the Facility of Antiproton and Ion Research project which goal is to build a new international accelerator facility that utilizes superconducting magnets. For the sake of electrical quality assurance of the superconducting magnet...
-
Remarks on the Subject of Back-Up Protection of Residual Current Devices
PublicationResidual current devices without integral overcurrent protection (RCCBs) are back-up protected by fuses or miniature circuit-breakers (MCBs). If the latter are used, special attention must be given to the coordination between an RCCB and an MCB. This paper indicates probable cases of the aforementioned devices coordination, in which back-up protection of the RCCB is not adequate. A laboratory test has shown that depending on the...
-
Optimum shape of turnout diverging track with segments of variable curvature
PublicationIn the paper an attempt has been made to focus on shaping the variable curvature in the diverging track of the railway turnout. Basing on some earlier studies, solutions provided with a circular arc in the mid-zone, and in the extreme regions with segments of non-linear curvature of equal length and zero curvature at the start and end of the turnout, have been assumed as models. The most advantageous type of curvature has been...
-
Intermetallic disordered magnet Gd2Pt1.1Ge2.9 and its relation to other AlB2 -type compounds
PublicationThe intermetallic germanide Gd 2 Pt 1.1 Ge 2.9 was synthesized using an arc-melting method. The crystal structure was characterized using powder x-ray diffraction, revealing a disordered ternary AlB 2 -type structure (space group P 6 / m m m , No. 191) with lattice parameters a = 4.2092 ( 1 ) Å and c = 4.0546 ( 2 ) Å . Physical properties were investigated by magnetic susceptibility and heat capacity measurements, which...
-
Crystal structure and physical properties of a novel ternary compound La15MoxGe9
PublicationWe present the synthesis, structural characterization and physical properties measurements of a new compound, La15MoxGe9 in Mn5Si3-type derived structure with interstitial Mo. The sample was synthesized by arc-melting method. La15MoxGe9 crystallizes in non-centrosymmetric hexagonal structure P63mc (#186) with lattice parameters a = b = 15.495(5) Å and c = 6.917(2) Å. The refinement on single X-ray diffraction data show that interstitial...
-
Synthesis and properties of HoT2Al20 (T = Ti, V, Cr) intermetallic cage compounds
PublicationPolycrystalline samples of HoT2Al20 (T = Ti, V, Cr) intermetallics were synthesized using a step-wise arc-melting technique. All three compounds adopt the CeCr2Al20-type crystal structure with Ho atoms positioned inside oversized icosahedral cages formed by Al atoms. The structure of HoV2Al20 compound is reported. The materials properties were studied by means of electrical resistivity, magnetic susceptibility, and specific heat...
-
DUABI - Business Intelligence Architecture for Dual Perspective Analytics
PublicationA significant expansion of Big Data and NoSQL databases made it necessary to develop new architectures for Business Intelligence systems based on data organized in a non-relational way. There are many novel solutions combining Big Data technologies with Data Warehousing. However, the proposed solutions are often not sufficient enough to meet the increasing business demands, such as low data latency while still maintaining high...
-
Polynomial Algorithm for Minimal (1,2)-Dominating Set in Networks
PublicationDominating sets find application in a variety of networks. A subset of nodes D is a (1,2)-dominating set in a graph G=(V,E) if every node not in D is adjacent to a node in D and is also at most a distance of 2 to another node from D. In networks, (1,2)-dominating sets have a higher fault tolerance and provide a higher reliability of services in case of failure. However, finding such the smallest set is NP-hard. In this paper, we...
-
Preliminary investigations of effect of conditions of FCAW process on diffusible hydrogen content in deposited metal
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper the state...
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublicationLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
Analysis of turnouts with non-linear curvature of diverging track for different train running speeds
PublicationThe paper deals with the issue of shaping a variable curvature in the diverging track of the railway turnout. Solution without a circular arc in the central zone, comprising two zones of non-linear curvature, of the same length, having zero curvature values at the end points, was adopted as a model, on the basis of the previously conducted dynamic tests. Optimum type of curvature was selected from the point of view of the kinematic...
-
Smoothed transition curve for railways
PublicationThe work draws attention to the existing situation in the area of transition curves used in the geometric layouts of the railway track. Difficulties in the practical implementation and maintenance of very small horizontal ordinates of the transition curve and the ordinates of the gradient due to cant in the initial section, appearing on smooth transition curves, were indicated. The main reason for this situation was the excessive...
-
Selection of Electrode Material for Inconel 617/P92 Steel SMAW Dissimilar Welds
PublicationThe present work aimed to investigate the microstructure and mechanical properties of the dissimilar shielded metal arc welded (SMAW) joint of Alloy 617 and P92 steel for advanced ultrasupercritical boilers. The SMAW joint was produced using three different types of electrodes, namely, ENiCrFe-3, ENiCrMo-3, and ENiCrCoMo-1. During microstructural observation of the welded joints, no possible cracking was detected in the weldments....
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublicationThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
Tourism for older and disabled people
PublicationTourist offer for the older and disabled is getting wider. Many hotels and cities are adjusted to disabled people's needs, but there are not enough safe places for leisure, where they could be surrounded by nature. In comparison with cities - villages and small towns have very little to offer as far as tourism is concerned. This problem is noticed by small local communities that threat it as a chance for their economical development....
-
Nonlinear Model of Synchronous Generator for Autonomous Electrical Power Systems Analysis
PublicationThis paper presents the nonlinear lookup table model for synchronous generator (SG) analysis. The saturation effects of the SG magnetic circuit have been considered. The saturated characteristic of the SG magnetic circuit are based on the open circuit saturation curve for magnetizing inductances. The model has been implemented into the Synopsys/Saber software using the MAST modelling language. To implement the no-load voltage characteristic...
-
Guided waves for monitoring of plate structures with linear cracks of variable length
PublicationDamage occurring at the work of plate structures may grow to a considerable size. The joint action – the detection of a defect at the earliest possible stage, the monitoring of its growth and the determination of its critical size in the context of structural reliability allows optimizing the cost of the maintenance and repair of structural elements. Thus the development of monitoring systems for permanent observation of fault...
-
Nonlinear model of a synchronous generator for analysis of more electric aircraft power systems
PublicationA nonlinear model for studying a variable-speed synchronous generator (SG) in more electric aircraft (MEA) power system has been developed. The saturation effects of the SG magnetic circuit have been considered. The model has been implemented in the Synopys/Saber simulation environment. The modelling language MAST has been used to elaborate the SG model. The model exhibit a network with the same number of external terminals/ports...
-
RCDs Tripping in the Range from DC to AC 50 kHz for Slowly Rising Residual Current
PublicationThe wide use of power electronic converters means that in many low-voltage systems earth fault currents containing components from DC to AC of various frequencies have to be taken into account. Due to the tendency to increase the modulation frequency in converters, components of higher frequencies may be in the order of several tens of kilohertz. Therefore, it is very important to verify the behavior of devices for protection against...
-
Service-based Resilience for Embedded IoT Networks
PublicationEmbedded IoT networks are the backbone of safety-critical systems like smart factories, autonomous vehicles, and airplanes. Therefore, resilience against failures and attacks should be a prior concern already in their design stage. In this study, we introduce a service-based network model as an MILP optimization problem for the efficient deployment of a service overlay to the embedded network by meeting QoS and resilience requirements....
-
The Latest Advances in Wireless Communication in Aviation, Wind Turbines and Bridges
PublicationPresent-day technologies used in SHM (Structural Health Monitoring) systems in many implementations are based on wireless sensor networks (WSN). In the context of the continuous development of these systems, the costs of the elements that form the monitoring system are decreasing. In this situation, the challenge is to select the optimal number of sensors and the network architecture, depending on the wireless system’s other parameters...