Search
Search results for: MODELLING AND SIMULATIONS
-
Hydrogen fuel cell power supply for hybrid elelectric multiple unit train
PublicationIn European countries, electrified routes amount for 40% to 65% of the total railway networks length. Some of those routes are only partially electrified, and construction of a catenary network might not be viable on all routes. Consequently, operators run diesel trains under catenary or require both an electric and diesel vehicle, increasing costs of operation. Dual-mode vehicles exist, but they are mostly equipped with diesel...
-
Design, modelling and analysis of a new type of piezoelectric motor. Multicell piezoelectric motor
PublicationThis paper describes a new type of piezoelectric motor. The results, obtained in the field of piezoelectric motors, have pointed out that these motors have potentially high possibilities in the future special applications. The research work presents the design, simulations and parameters of the piezoelectric motor with three rotation-mode actuators. The motor is characterized by a high power, relative high speed and torque. The...
-
Rapid tolerance‐aware design of miniaturized microwave passives by means of confined‐domain surrogates
PublicationThe effects of uncertainties, primarily manufacturing tolerances but also incomplete information about operating conditions or material parameters, can be detrimental to the performance of microwave components. Quantification of such effects is essential to ensure a meaningful evaluation of the structure, in particular, its reliability under imperfect fabrication procedures. The improvement of the circuit robustness can be achieved...
-
Modelling of sequencing batch reactor operating at various aeration modes
PublicationThe presented study involved designing a computer model of a sequencing batch reactor (SBR) at laboratory scale. The data pertaining to the technical aspects of the bioreactor and quality indicators of wastewater constituted the input for the employed simulation tool, i.e. GPS-X software package. The results of a simulation involving a 12-hour operation cycle are presented in this work; each cycle included 6 phases: filling, mixing,...
-
Numerical Analysis of Recharge Rates and Contaminant Travel Time in Layered Unsaturated Soils
PublicationThis study focused on the estimation of groundwater recharge rates and travel time of conservative contaminants between ground surface and aquifer. Numerical simulations of transient water flow and solute transport were performed using the SWAP computer program for 10 layered soil profiles, composed of materials ranging from gravel to clay. In particular, sensitivity of the results to the thickness and position of weakly permeable...
-
Impact of different car-following models on estimating safety and emissions on signal-controlled intersections using microscopic simulations
PublicationThis paper examines the influence of two selected car-following models on the outcomes of microscopic traffic simu-lations. The authors begin by reviewing the literature on the various traffic models, methods for estimating energy consumption, fuel use, and emissions. The authors discuss using surrogate safety measures derived from analysing vehicle trajectories in a microscopic traffic model to estimate safety levels. This paper...
-
Evolution of Ag nanostructures created from thin films: UV–vis absorption and its theoretical predictions
PublicationAg-based plasmonic nanostructures were manufactured by thermal annealing of thin metallic films. Structure and morphology were studied using scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HR-TEM) and X-ray photoelectron spectroscopy (XPS). SEM images show that the formation of nanostructures is influenced by the initial layer thickness as well as the...
-
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublicationIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
Modelling and Simulation of a New Variable Stiffness Holder for Milling of Flexible Details
PublicationModern industry expectations in terms of milling operations often demand the milling of the flexible details by using slender ball-end tools. This is a difficult task because of possible vibration occurrence. Due to existence of certain conditions (small depths of cutting, regeneration phenomena), cutting process may become unstable and self-excited chatter vibration may appear. Frequency of the chatter vibration is close to dominant...
-
Badania eksperymentalne i symulacyjne dynamiki modelowego odcinka sieci trakcyjnej
PublicationW pracy przedstawiono główne założenia i strukturę opracowanego modelu matematycznego odcinka kolejowej górnej sieci trakcyjnej, opartego na metodzie energetycznej Lagrange’a. W celu wyznaczenia wybranych parametrów modelu, jak również dla oceny stopnia zgodności odwzorowania przez utworzony program symulacyjny stanów statycznych i dynamicznych sieci zbudowano laboratoryjny model odcinka sieci jezdnej z użyciem rzeczywistych jej...
-
Response of a fiber-optic Fabry-Pérot interferometer to refractive index and absorption changes – modelling and experiments
PublicationThis paper describes how the refractive index and the absorption of investigated substances change the spectrum of the optical radiation at the output of the fiber-optic Fabry-Pérot interferometer. The modeling of the operation of the interferometer takes into account not only the spectra of the refractive index and the absorption of the medium that is inside the cavity, but also spectra of the refractive indices of the core and...
-
Enhancing colloidal stability of nanodiamond via surface modification with dendritic molecules for optical sensing in physiological environments
PublicationPre-treatment of diamond surface in low-temperature plasma for oxygenation and in acids for carboxylation was hypothesized to promote the branching density of the hyperbranched glycidol polymer. This was expected to increase the homogeneity of the branching level and suppress interactions with proteins. As a result, composite nanodiamonds with reduced hydrodynamic diameters that are maintained in physiological environments were...
-
Strategies for mitigating nitrous oxide production and decreasing the carbon footprint of a full-scale combined nitrogen and phosphorus removal activated sludge system
PublicationNitrous oxide (N2O) emitted from biological nutrient removal activated sludge systems contributes significantly to the total carbon footprint of modern wastewater treatment plants. In the present study, N2O production and emissions were experimentally determined in a large-scale plant (220,000 PE) employing combined nitrogen (N) and phosphorus (P) removal. As a modelling tool, the Activated Sludge Model 2d (ASM2d) was extended...
-
Application of the Bodner-Partom constitutive equations for modelling of the technical fabric Valmex used for the hanging roof of the Forest Opera in Sopot
PublicationThe study of an inelastic properties of the technical fabric Valmex used for 20 years as the roof structure of the Forest Opera in Sopot (Poland) is presented. The uniaxial tensile laboratory tests with constant strain rate have been conducted and analysed. Parameters of the Bodner-Partom constitutive model have been identified and verified by numerical simulations. Two approaches of the parameters identification have been proposed:...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Numerical modelling of different airbag folding patterns and their influence on occupant responses in frontal vehicle impact
PublicationThis paper presented a procedure for airbag folding for the application in occupant safety studies and analysed the influence of different airbag folding patterns on the occupant severity in frontal impact. Airbags were folded in two patterns: zig-zag and top-roll, using two folding techniques: Initial Metric Method and Explicit Folding. The explicit folding was found to be more expensive in terms of preparation time. However,...
-
Modelling of shear zones during quasi-static granular silo flow using material point method (MPM)
PublicationThe paper focuses on confined silo flow of cohesionless sand. The problem considered is a quasi-static flow in a plane strain model silo with parallel walls simulated with the material point method (MPM). The simulation used a non-local hypoplastic constitutive model. Initially, the paper validated the implemented numerical approach with basic element tests and a plane strain compression test. The subsequent MPM calculations for...
-
Refinement of the Hardening Soil model within the small strain range
PublicationThe popularity of the elasto-plastic Hardening Soil (HS) model is based on simple parameter identification from standard testing and empirical formulas. The HS model is implemented in many commercial FE codes designed to analyse geotechnical problems. In its basic version, the stress–strain behaviour within the elastic range is subject to the hypoelastic power law, which assures the barotropy of the elastic stiffness. However,...
-
Spectral Finite Element Method in Condition Monitoring and Damage Detection
PublicationIt is well known that the dynamic behaviour of engineering structures may carry very important and crucial information that can be further used for the assessment of their condition as well as detection of any damage induced. The current interest in monitoring techniques based on the propagation of guided elastic waves requires that numerical techniques used for modelling the phenomena associated must shift into the realm of high...
-
MATHEMATICAL MODELING OF FLOOD MANAGEMENT SYSTEM IN THE CITY OF GDAŃSK, ORUŃSKI STREAM CASE STUDY
PublicationAim of the study This study analyses the efficiency of flood protection in a small urban catchment, based on a system of small reservoirs. Material and methods To assess the flood routing and surge reduction, a mathematical model of the river catchment was implemented. This was a lumped hydrological model, based on the SCS-CN method. Channel routing was performed, using kinematic wave equation. The sub-catchments have been determined...
-
Low-cost performance-driven modelling of compact microwave components with two-layer surrogates and gradient kriging
PublicationUtilization of electromagnetic (EM) simulation tools has become indispensable for reliable evaluation of microwave components. As the cost of an individual analysis may already be considerable, the computational overhead associated with EM-driven tasks that require massive simulations (e.g., optimization) may turn prohibitive. One of mitigation methods is the employment of equivalent network models. Yet, they are incapable of accounting...
-
FLOOD MANAGEMENT IN URBAN BASINS OF THE CITY OF GDAŃSK
PublicationOver the last years, the City of Gdańsk suffers twice from flash floods. Both events were caused by intense storms which produced significant surface runoff and caused inundation private and cities properties. The first case of July 2001 flood [3], [9] was the turning point for the city authorities, who decide to look close on the flood management in small urban catchments. The aim of research projects was to establish technical...
-
Experimental and numerical study of thermal and electrical potential of BIPV/T collector in the form of air-cooled photovoltaic roof tile
PublicationAmong renewable energy sources, Building-Integrated Photovoltaic/Thermal (BIPV/T) systems are gaining increasing interest. To improve their economic competitiveness, technologies that increase their efficiency are searched for. The paper is devoted to evaluating the impact of various air-cooling configurations on the thermal and electrical performance of a photovoltaic roof tile. A numerical model of the own experimental system...
-
NUMERICAL MODEL QUALITY ASSESSMENT OF OFFSHORE WIND TURBINE SUPPORTING STRUCTURE BASED ON EXPERIMENTAL DATA
PublicationAs a structure degrades some changes in its dynamical behavior can be observed, and inversely, observation and evaluation of these dynamical changes of the structure can provide information of structural state of the object. Testing of the real structure, besides of being costly, can cover only limited working states. It is particularly considerable in case of hardly accessible, and randomly/severely dynamically loaded offshore...
-
Modelling hydraulic and capillary-driven two-phase fluid flow in unsaturated concretes at the meso-scale with a unique coupled DEM-CFD technique
PublicationThe goal of the research was to demonstrate the impact of thin porous interfacial transition zones (ITZs) between aggregates and cement matrix on fluid flow in unsaturated concrete caused by hydraulic/capillary pressure. To demonstrate this impact, a novel coupled approach to simulate the two-phase (water and moist air) flow of hydraulically and capillary-driven fluid in unsaturated concrete was developed. By merging the discrete...
-
Proportional-Derivative and Model-Based Controllers for Control of a Variable Mass Manipulator
PublicationIn the paper, numerical analysis of dynamics of a variable mass manipulator is presented. A revolute joints composed manipulator is considered. Payload of the gripper is considered as the only element characterized by unknown value of its mass (variable between subsequent operations). As in other cases of the revolute joints composed manipulators, its behaviour dependents significantly on the pose of the manipulator. When the manipulator...
-
H2O˙+ and OH+ reactivity versus furan: experimental low energy absolute cross sections for modeling radiation damage
PublicationRadiotherapy is one of the most widespread and efficient strategies to fight malignant tumors. Despite its broad application, the mechanisms of radiation-DNA interaction are still under investigation. Theoretical models to predict the effects of a particular delivered dose are still in their infancy due to the difficulty of simulating a real cell environment, as well as the inclusion of a large variety of secondary processes. This...
-
Simplified Distribution Grid Modelling for Connection Analyses
PublicationThis paper considers the modelling of medium and low voltage grids for the purpose of connection studies by distribution grid operators. Possible simplifications in grid modelling are discussed, which are acceptable from the viewpoint of the final result. The main driver of the modelling simplification is the MS Excel environment used as the computation platform, and the limitation of time for grid modelling.
-
PHYSICAL MODELLING OF GEOTECHNICAL STRUCTURES IN PORTS AND OFFSHORE
PublicationThe physical modelling of subsoil behaviour and soil-structure interaction is essential for the proper design of offshore structures and port infrastructure. A brief introduction to such modelling of geoengineering problems is presented and some methods and experimental devices are described. The relationships between modelling scales are given. Some examples of penetration testing results in centrifuge and calibration chamber...
-
Diagnostyka eksploatacyjna okrętowych silników spalinowych - tłokowych i turbinowych
PublicationW monografii przedstawiono wybrane zagadnienia diagnostyki technicznej silników spalinowych dużej mocy, zarówno tłokowych, jak i turbinowych, ukierunkowane na eksploatację okrętowych (i nie tylko) systemów energetycznych, w których występują tego typu silniki. W początkowej części opracowania zaproponowano koncepcję systemowego ujęcia diagnostyki eksploatacyjnej silników okrętowych w aspekcie obowiązujących standardów światowych...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublicationDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Modeling of the internal combustion engine cooling system
PublicationThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
Modelling of power electronic compensators for the analysis of power system operation
PublicationThe article presents selected methods of modelling power electronic compensators in order to analyze their operation in the power systems. Advantages and disadvantages of models have been shown with an indication of their usefulness for modelling specific phenomena.
-
Derivation of the scaling laws used in geotechnical centrifuge modelling-application of dimensional analysis and Buckingham Π theorem
PublicationGeotechnical centrifuge modelling has been a world-wide used technology in physical tests. In this paper a derivation of scaling laws by dimensional analysis for the centrifugal modelling is presented. Basic principles of centrifuge modelling are described. Scaling laws for slow events like consolidation and fast events like dynamic loads are shown. The differences in scale factors for both processes are noticed. The aim of this...
-
Mode choice modelling for urban areas
PublicationThe article presents the question of mode choice modelling in a four-stage travel modelling process. The article indicates limitations of currently used simplified methods of mode choice modelling and presents the possibility of using a more detailed approach that accounts for additional, statistically significant factors with the use of advanced mathematical tools, discrete choice models. A need has also been identified to include...
-
Biological processes modelling for MBR systems: A review of the state-of-the-art focusing on SMP and EPS
PublicationA mathematical correlation between biomass kinetic and membrane fouling can improve the understanding and spread of Membrane Bioreactor (MBR) technology, especially in solving the membrane fouling issues. On this behalf, this paper, produced by the International Water Association (IWA) Task Group on Membrane modelling and control, reviews the current state-of-the-art regarding the modelling of kinetic processes of biomass, focusing on...
-
Wiktoria Wojnicz dr hab. inż.
PeopleDSc in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2019 PhD in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2009 (with distinction) List of papers (2009 - ) Wojnicz W., Wittbrodt E., Analysis of muscles' behaviour. Part I. The computational model of muscle. Acta of Bioengineering and Biomechanics, Vol. 11, No.4, 2009, p. 15-21 Wojnicz W., Wittbrodt E., Analysis of...
-
Mathematical modelling and computer simulation of activated sludge systems.Second edition
PublicationMathematical Modelling and Computer Simulation of Activated Sludge Systems – Second Edition, provides, from the process engineering perspective, a comprehensive and up-to-date overview regarding various aspects of the mechanistic (“white box”) modelling and simulation of advanced activated sludge systems performing biological nutrient removal. In the new edition of the book, a special focus is given to nitrogen removal and an overview...
-
Modeling of Combined Phenomena Affecting an AUV Stealth Vehicle
PublicationIn the paper some results of research connected with modelling the basic stealth characteristics of an AUV vehicle are presented. First of all a general approach to design of the stealth AUV autonomous underwater vehicle under consideration is introduced. Then, the AUV stealth vehicle concept is briefly described. Next a method of modelling of the stealth characteristics is briefly described as well. As an example of the stealth...
-
Port-Based Modelling of Distributed-Lumped Parameter Systems
PublicationThere in the paper is presented an uniform, port-based approach to modelling of both lumped and distributed parameter systems. Port-based model of the distributed system has been defined by application of bond graph methodology and distributed transfer function method (DTFM). The approach proposed combines versatility of port-based modelling and accuracy of distributed transfer function method. The concise representation of lumped-distributed...
-
Application of spatial neural simulators of turbine blade rows to fluid flow diagnostics
PublicationThis chapter presents the results of neural modelling of fluid flow in steam turbine row. In modelling working conditions of the flow channel varied, thus the aim of the work was to reconstruct the reference state - distributions of velocity, pressure, and losses in flow channel - with high accuracy for fluid flow diagnostics.
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublicationLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublicationIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...
-
Raman Scattering versus Strain Engineering in Phosphorene Nanostructures: An Ab Initio Studies
PublicationThe one-dimensional nanoribbons made from phosphorene are novel structures with great applicability potential in material science. The significant carrier mobility combined with intrinsic semiconductor properties makes them ideal for application in electronics, and they are excellent candidates for sensing material. The lack of a well–established multiscale modelling strategy for phosphorene nano optoelectronic devices is one of...
-
Modelling a 6-dof manipulator using Matlab software
PublicationThis paper presents an alternative approach to modelling a revolute robot. The manipulator in question is Kuka KR 16-2. The main problem in robot modelling is a kinematic analysis. The revolute robot consist of six rotary joints (6-DOF) with base, shoulder, elbow and wirst. The kinematics problem is defined as a transformation from the cartesian space to the joint space. The Denavit- Hartenberg (D-H) model of representation was...
-
Designing Control and Protection Systems with Regard to Integrated Functional Safety and Cybersecurity Aspects
PublicationThis article addresses current problems of risk analysis and probabilistic modelling for functional safety management in the life cycle of safety-related systems. Two main stages in the lifecycle of these systems are distinguished, namely the design and operation. The risk analysis and probabilistic modelling differ in these stages in view of available knowledge and data. Due to the complexity and uncertainty involved, both qualitative...
-
Between Descriptive Geometry and CAD 3D
PublicationDescriptive geometry provides methods to analyse three-dimensional space through two-dimensional drawings and prepares to create technical documentation. Geometric form of an engineering project is presented by the means of projection methods based on a 3D model, which is present in designer’s imagination. The forthcoming era of Building Information Modelling (BIM) brings changes in the way the engineer works, as the vision is...
-
Quasi-discrete modelling of PMSM phase currents in drives with low switching-to-fundamental frequency ratio
PublicationThis study proposes a new quasi-discrete approach to modelling the permanent magnet synchronous motor (PMSM). The quasi-discrete modelling reflects the impact of continuous rotor movement, which takes place during a control cycle, on the shape of motor current waveforms. This provides much improvement in current modelling accuracy under inverter low switching-to-fundamental frequency operation. The proposed approach may be used...
-
Mainstream shortcut N removal modeling current status and perspectives
PublicationThis work gives an overview of the state-of-the-art in modelling of short-cut processes for nitrogen removal in mainstream wastewater treatment and presents future perspectives for directing research efforts in line with the needs of practice. The modelling status for deammonification (i.e., anammox-based) and nitrite-shunt processes is presented with its challenges and limitations. The importance of mathematical models for considering...
-
Low cost real time UAV stereo photogrammetry modelling technique – accuracy considerations
PublicationThe paper presents accuracy considerations regarding three 3D modelling techniques. The tested new consumer type stereo camera (ZED 3D Stereolabs) has been implemented info an aerial mapping system, on board micro air vehicle MAV) and tested object has been mapped using a real-time photogrammetry with original real-time software application. The evaluated results has been compared with model gained with a state of art unmanned...