Search results for: GENERATOR WIRÓW WZDŁUŻNYCH
-
Sensorless Disturbance Detection for Five Phase Induction Motor with Third Harmonic Injection
PublicationThe paper presents a sensorless disturbance detection procedure that was done on a five phase induction motor with third harmonic injection. A test bench was developed where a three phase machine serves as disturbance generator of different frequencies. The control of the machines is based on multi scalar variables that ensures an independent control of the motor EMF and the rotor flux. For disturbance identification a speed observer...
-
50’ Sail Catamaran with Hybrid Propulsion, Design, Theoretical and Experimental Studies
PublicationThe development of modern lithium batteries and propulsion systems now allows the use of complex propulsion systems for vessels of various sizes. As part of the research and implementation project, a parallel hybrid drive system was designed, built and then tested in the laboratory. The experimental studies conducted allowed for the measurements of power, fuel consumption and electric power distribution in various operating modes...
-
The voltage on bus bars of the main switchboard of the ferry electrical power system during a layover at the port
Open Research DataThe dataset is part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. The attached dataset contains the measurement results carried out onboard the ferry during a layover at the port.
-
Sterowanie poziomami napięć i rozpływem mocy biernej w lokalnych elektrowniach z generatorami synchronicznymi.
PublicationW krajowym systemie elektoenergetycznym możliwości regulacyjne lokalnych elektrowni w zakresie sterowania poziomami napięć i rozpływem mocy biernej dotychczas wykorzystywane są mało. Przyczyną jest brak odpowiednich systemów rozliczeń i nieprzystosowanie układów regulacyjnych. Opisano możliwe cele takiej regulacji oraz zaprezentowano niektóre sposoby potrzebnego rozwoju układów regulacyjnych elektrowni lokalnych. W szczególności...
-
Technisch-wirtschaftliche Analyse verschiedener Moglichkeiten zur Energie versorgung einer historischen Stadtvilla.
PublicationW pracy rozważono kilka wybranych wariantów systemów grzewczych i grzewczo-elektrycznych możliwych do zainstalowania w willi o znaczeniu historycznym. Przedstawiono wyniki analizy technicznej i ekonomicznej systemów opartych na: klasycznym kotle wodnym opalanym gazem ziemnym, module termomechanicznym(silnik spalinowy+generator energii elektrycznej), pompie ciepła napędzanej silnikiem spalinowym na gaz ziemny, ogniwie paliwowym....
-
Monitoring the gas turbine start-up phase on the platform using a hierarchical model based on Multi-Layer Perceptron networks
PublicationVery often, the operation of diagnostic systems is related to the evaluation of process functionality, where the diagnostics is carried out using reference models prepared on the basis of the process description in the nominal state. The main goal of the work is to develop a hierarchical gas turbine reference model for the estimation of start-up parameters based on multi-layer perceptron neural networks. A functional decomposition...
-
Przykłady zastosowań
PublicationW rozdziale przedstawiono przykładowy sposób analizy funkcji systemów sterowania i zabezpieczeń w odniesieniu do turbozespołu o strukturze typu: kocioł-turbina-generator. Ryzyko związane z eksploatacją turbozespołu zależy od różnych czynników i rozwiązań technicznych, organizacyjnych oraz od zastosowanych podsystemów sterowania, zabezpieczeń oraz systemów E/E/PE związanych z bezpieczeństwem. Jednym z elementów takiego podsystemu...
-
Detection of the acoustic interferences during AFM operation
Open Research DataAtomic force microscopy is a particularly complicated surface imaging technique due to the large number of factors that affect the quality of the resulting images. They are obviously difficult and sometimes even impossible to control at the same time. One of such factors may even be the seismological location of the building or the influence of mechanical...
-
Simulations of the Behavior of Granular Bodies Using the Discrete Element Approach
PublicationZachowanie niespójnych ciał ziarnistych opisano metodą elementów dyskretnych (DEM) w warunkach quasi-statycznych dwu- i trójwymiarowych. Do symulacji nieregularnego kształtu granulatu wykorzystano kule z momentami kontaktowymi lub skupiska sztywnych kul. Początkowo badano dwa różne problemy dla zagęszczonego materiału ziarnistego: pasywne przemieszczanie ściany oporowej i ściskanie w płaskim stanie odkształceń pod stałym ciśnieniem...
-
Właściwości uzwojeń koncentrycznych ułamkowo-żłobkowych w aspekcie jakości napięcia generatorów synchronicznych
PublicationW artykule przedstawiono wyniki analizy właściwości uzwojeń koncentrycznych ułamkowo żłobkowych. Porównano wartość współczynnika uzwojenia dla podstawowej harmonicznej oraz zawartość wyższych harmonicznych. Obliczenia wykonano w oparciu o zależności analityczne zaimplementowane w specjalnie przygotowanym programie komputerowym. W celu weryfikacji wyników przygotowano model numeryczny maszyny bezszczotkowej maszyny prądu przemiennego...
-
The voltage on bus bars of the main switchboard of the ro-ro ship electrical power system during maneuvering
Open Research DataThe dataset is part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. The attached dataset contains the measurement results carried out onboard a ro-ro ship during maneuvering.
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Analytical and reliability data from the real-time simulator biogas plant
Open Research DataThe dataset represents the results of biogas plant simulation. The described plant is an agricultural biogas system, which can produce electrical energy with power estimated up to 1070 kW and heat energy that can reach 1200 kW simultaneously.
-
Sound Field Intensity Measurements and Visualization around the Human Head Model . Rozkłąd natężenia pola akustycznego w komorze bezechowej obecności sztucznej głowy i w przypadku braku jej obecności
PublicationThe main goal of this research study was to measure and visualize sound field intensity distribution in and without presence of the human head model. Measurements were performed in the anechoic chamber with the 5 cm grid. Experimental setup consisted of a multitone generator, two loudspeakers, human head model, intensimetric probe, the Cartesian robot applied for precise positioning of the acoustic sensor, and an analyzer. Based...
-
Piezo 2011, Electroceramics for End-Users VI
PublicationThis work extends a power harvesting with using piezoelectric materials. Experimental presents the development of a piezoelectric MEMS generator which has the ability to scavenge mechanical energy of ambient vibrations from their surroundings and transform it into electrical energy that can be used in energy storage applications. Recent literature shows that piezoelectric transduction has received the most attention for vibration-to-electricity...
-
BLDFIG Design and development of a high-efficiency wind turbine based on a slow-speed gearless multiphase doubly-fed induction generator
ProjectsProject realized in Department of Power Electronics and Electrical Machines according to LIDER13/0153/2022 agreement from 2023-03-24
-
RAPORT - EKSPERTYZA Z POMIARÓW DRGAŃ LINII WAŁÓW NA JEDNOSTCE R14
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego lini transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne linii wałów okrętowego układu napędowego wykonano po naprawie głównej napędu okrętu w stoczni „NAUTA”, w celu określenia jego stanu dynamicznego. Rejestrację drgań przeprowadzono w płaszczyźnie pionowej (V)...
-
Problemy dostosowana układu sterowania maszyną dwustronnie zasilaną do nowych wymagań.
PublicationW artykule zaprezentowano problemy związane z dostosowaniem układu sterowania maszyną dwustronnie zasilaną pracującą jako generator w elektrowni wiatrowej do nowych wymagań i przepisów stawianych przez operatorów sieci energetycznych. Poruszono problem utrzymania elektrowni wiatrowej w systemie w momencie krótkotrwałego obniżenia lub uskoku napięcia sieci energetycznej spowodowanego odległym zwarciem w systemie lub podłączeniem...
-
Pitch shifter with complex instantaneous frequency rescaling and direct digital synthesis
PublicationW artykule zaprezentowano nowy przesuwnik wysokości dźwięku ze skalowaniem częstotliwości chwilowej i z syntezą bezpośrednią. Jest on przeznaczony do komponowania melodii np. w telefonie komórkowym. Implementacja przesuwnika jest oparta na twierdzeniu Bedrosiana, zastosowanego do zespolonego odpowiednika hilbertowskiego przetwarzanego sygnału rzeczywistego. Filtr Hilberta pełni tu też dodatkową rolę. Jest nią filtracja antyaliasingowa....
-
Analysis of Measurement Errors in Rail Vehicles’ Pantograph Inspection System
PublicationThe paper presents an approach to evaluation of height measurement errors in laser scanning inspection system. The system, consisting of a laser line generator and a specialized camera, is dedicated to diagnosing carbon contact strips of railway vehicles’ pantographs. While height measurement resolution is easily computable based on system parameters, determining the measurement error is troublesome due to numerous impacts. As...
-
RAPORT-EKSPERTYZA Z POMIARÓW DRGAŃ LINII WAŁÓW NA JEDNOSTCE ORP „PIORUN”
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego lini transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne linii wałów okrętowego układu napędowego wykonano po naprawie głównej napędu okrętu w stoczni „NAUTA”, w celu określenia jego stanu dynamicznego. Rejestrację drgań przeprowadzono w: • płaszczyźnie pionowej (V)...
-
Wpływ konstrukcji przestrzeni międzyklockowej na charakterystyki wzdłużnego łożyska ślizgowego
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania dużych wzdłużnych łożysk ślizgowych. W chwili obecnej wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności łożyska, które następuje m. in. po obniżeniu temperatury maksymalnej w filmie smarowym, co można uzyskać poprzez skuteczne dostarczanie zimnego oleju zasilającego wprost do strefy wlotowej filmu olejowego. Jednym z takich rozwiązań konstrukcyjnych,...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego z wykorzystaniem komputerowej dynamiki płynów (CFD) = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove with the use of computational fluid dynamic
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Obecnie wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublicationMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part I: Steady-state processes
PublicationThe article presents a possible method of detecting failures in the flow section and supply system of a naval gas turbine engine based on the exhaust gas temperature measured behind the gas generator. This temperature is a basic diagnostic parameter use for evaluating the technical state of the turbine engine in operation, and is monitored during engine start-ups, accelerations and decelerations of rotor units, and steady-load...
-
Power augmentation of PGE Gorzow's gas turbine by steam injection - thermodynamic overview
PublicationThe impact of steam injection upon a gas turbine and a combined power plant performance has been investigated. This article describes and summarizes possibilities of modification for current gas turbine in PGE Gorzow power plant into the Cheng cycle. Our modification deals with a thermal cycle, in which steam produced in a heat recovery steam generator is injected into the gas turbine's combustion chamber. It has been proved that...
-
Quantum security and theory of decoherence
PublicationWe sketch a relation between two crucial, yet independent, fields in quantum information research, viz. quantum decoherence and quantum cryptography. We investigate here how the standard cryptographic assumption of shielded laboratory, stating that data generated by a secure quantum device remain private unless explicitly published, is disturbed by the einselection mechanism of quantum Darwinism explaining the measurement process...
-
Efficient FPGA Implementation of an RFIR Filter Using the APC–OMS Technique with WTM for High-Throughput Signal Processing
PublicationNowadays, Finite Impulse Response (FIR) filters are used to change the attributes of a signal in the time or frequency domain. Among FIR filters, a reconfigurable filter has the advantage of changing the coefficient in real-time, while performing the operation. In this paper, the Anti-Symmetric Product Coding (APC) and Odd Multiple Storage (OMS) modules are utilized to implement the reconfigurable FIR filter (RFIR–APC–OMS). Herein,...
-
Measurements of passive components using of an IEEE 1149.4 mixed-signal test bus
PublicationW pracy przedstawiono wyniki badań nad wykorzystaniem magistrali testującej mieszanej sygnałowo IEEE 1149.4 do pomiarów elementów pasywnych zamontowanych na pakietach elektronicznych. Do badań użyto wyposażonych w magistralę układów scalonych typu STA400. Zaprezentowano metody pomiaru rezystancji pojedynczych elementów z wykorzystaniem źródła prądowego oraz źródła VH znajdującego się w analogowych modułach ABM układu STA400. Pokazano...
-
ZARZĄDZANIE STRATEGIAMI SZLIFOWANIA SZYN W PROCESIE UTRZYMANIA NAWIERZCHNI KOLEJOWYCH
PublicationSzlifowanie szyn kolejowych od co najmniej kilkunastu lat jest podstawową i integralną czynnością na rzecz prawidłowego utrzymania nawierzchni kolejowej i wydłużenia jej trwałości. Technologia, która pierwotnie stosowana była do usuwania tzw. zużyć falistych, czyli wzdłużnych nierówności powierzchni tocznej główki szyny, w coraz szerszym zakresie wprowadzana jest jako czynność planowo-zapobiegawcza. Zwiększone obciążenia dynamiczne...
-
Synteza układu regulacji maszyny dwustronnie zasilanej zmodyfikowanego przez zastosowanie sieci neuronowej.
PublicationMaszyna dwustronnie zasilana stosowana jest jako generator w elektrowniach wiatrowych, gdzie występują bardzo ostre wymagania dotyczące jakości wytwarzanej energii elektrycznej oraz specyficzne problemy mechaniczne. Projekt dotyczy układu regulacji mocy maszyny dwustronnie zasilanej, będącej złożonym, nieliniowym obiektem, w którym mogą pojawiać się bardzo słabo tłumione oscylacje. Celem pracy było opracowanie układu regulacji...
-
Modelowanie małej elektowni wiatrowej
PublicationW pracy przedstawiono model elektrowni wiatrowej o mocy 8500W wyposażonej w generator z silnikiem synchronicznym z magnesami trwałymi. W oparciu o analizę dostępnej literatury naukowej, norm technicznych, opracowano model elektrowni wiatrowej, który został zaimplementowany w środowisku Matlab Simulink. Model ten pozwala przeprowadzić analizę elektrowni wiatrowej, w której regulacja wytwarzanej energii odbywa się z wykorzystaniem...
-
A Preliminary Study and Analysis of Tidal Stream Generators
PublicationFor a sustainable future, tidal energy can play a vital role. Tidal energy relies on the gravitational pull of the Moon and the Sun along with the centrifugal forces created by the Earth. Tidal barrage uses the potential energy from the tide and has been very successful in electricity production. With the help of a turbine, kinetic energy can also be harnessed from tidal currents to generate electricity. However, it is not economically...
-
A multirate approach to DDS algorithm versus Taylor-series expansion technique.
PublicationPokazano, że cyfrowy generator syntezy bezpośredniej (DDS) można traktować jako algorytm wieloszybkościowy. Rozważono i porównano dwa sposoby wykorzystania pamięci. W pierwszym z nich zastosowano filtr ułamkowo-opóźniający o strukturze Farrowa. Drugie podejście oparto na rotacji fazy na podstawie rozwinięcia w szereg Taylora. Eksperymenty pokazują, że za pomocą obu tych sposobów, dla sinusoidy zespolonej generowanej w kwadraturowym...
-
Multiscalar Control Based Airgap Flux Optimization of Induction Motor for Loss Minimization
PublicationBased on the induction motor model, considering the core loss resistance that accounts for magnetic characteristic saturation, a speed control approach is devised with an adaptive full-order (AFO) speed observer. The induction motor model analysis is done sincerely in a stationary reference frame. The control approach incorporates a flux reference generator designed to meet optimal operational circumstances and a nonlinear speed...
-
Nitrogen oxides removal from hydrogen flue gas using corona discharge in marine boilers: Application perspective
PublicationThis paper focuses on the combustion of hydrogen in boilers, as it appears to be a more effective method than using fuel cells for heating purposes due to higher boiler efficiency. One of the main disadvantages of hydrogen combustion in air is NOx formation. Therefore, the authors decided to introduce corona discharge as an inno- vative technique to clean hydrogen flue gas by effectively reducing NOx levels. The method involves...
-
High-Speed Binary-to-Residue Converter Design Using 2-Bit Segmentation of the Input Word
PublicationIn this paper a new approach to the design of the high-speed binary-to-residue converter is proposed that allows the attaining of high pipelining rates by eliminating memories used in modulo m generators. The converter algorithm uses segmentation of the input binary word into 2-bit segments. The use and effects of the input word segmentation for the synthesis of converters for five-bit moduli are presented. For the number represented...
-
Dynamic Research of Masonry Vault in a Technical Scale
PublicationThe paper presents preliminary results of dynamic tests of the masonry barrel vault in a technical scale. Experimental studies are intended to identify material properties of homogenized masonry vaults under dynamic loads. The aim of the work is to create numerical models to analyse vault’s dynamic response to dynamic loads in a simplest and accurate way. The process of building the vault in a technical scale is presented in the...
-
The experience of movement in the built form and space: A framework for movement evaluation in architecture
Publication“Movement in architecture” is an organized system of various types of movements stimulated by specific architectural elements. This research was conducted through a qualitative-analytical method and empirical and bibliographical research methods with the aim to categorize different types of movements based on the explorer and observer relationships with the built space and form. So far, most of the related studies have focused...
-
Current divider-based nanosecond high current pulse measuring systems
PublicationThis paper presents the analysis of the new approach to the measurement methodology of significant values (in order of hundreds of kA) and huge steepness (in order of MA/μs) current pulses based on current dividers along with a comparison of the various types transducers suitability in measuring systems with such extreme parameters. Such dividers are used to extend the measurement ranges of current transducers with limited current...
-
Wear in siding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specim. sets #20-#21, #22-#23, #24-#25, #26-#27, #28-#29,#30 - #31. Run time: 4-8h.
Open Research DataWear in sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer.Running time: 4-8h.Specimen sets:Specim. sets (# [upper, rotating] - #[lower, non-rotating]):#20-#21, #22-#23, #24-#25, #26-#27,...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #24 - #25.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #24 (upper, rotating), #25 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Wear in siding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specim. sets #20-#21, #22-#23, #24-#25, #26-#27, #28-#29,#30 - #31. Run time: 0-4h.
Open Research DataWear in sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer.Running time: 0 - 4h.Specimen sets:Specim. sets (# [upper, rotating] - #[lower, non-rotating]):#20-#21, #22-#23, #24-#25, #26-#27,...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #30 - #31.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #30 (upper, rotating), #31 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #20 - #21.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #20 (upper, rotating), #21 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #22 - #23.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #22 (upper, rotating), #23 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #26 - #27.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #26 (upper, rotating), #27 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...