Search results for: CCR PLATFORMING UNIT
-
X-RAY DIFFRACTION STUDY OF BISMUTH LAYER-STRUCTURED MULTIFERROIC CERAMICS
PublicationGoal of the present research was to apply a solid state reaction route to fabricate bismuth layer-structured multiferroic ceramics described with the formula Bi5FeTi3O15 and reveal the influence of processing conditions on its crystal structure and phase composition. Simple oxide powders Bi2O3, TiO2 and Fe2O3 were used to fabricate Aurivillius-type bismuth layer-structured ferroelectrics. Pressureless sintering in ambient air was...
-
A comparative study of English viseme recognition methods and algorithm
PublicationAn elementary visual unit – the viseme is concerned in the paper in the context of preparing the feature vector as a main visual input component of Audio-Visual Speech Recognition systems. The aim of the presented research is a review of various approaches to the problem, the implementation of algorithms proposed in the literature and a comparative research on their effectiveness. In the course of the study an optimal feature vector...
-
A comparative study of English viseme recognition methods and algorithms
PublicationAn elementary visual unit – the viseme is concerned in the paper in the context of preparing the feature vector as a main visual input component of Audio-Visual Speech Recognition systems. The aim of the presented research is a review of various approaches to the problem, the implementation of algorithms proposed in the literature and a comparative research on their effectiveness. In the course of the study an optimal feature vector construction...
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublicationThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
Charge density wave and large nonsaturating magnetoresistance in YNiC2 and LuNiC2
PublicationWe report a study of physical properties of two quasi-low-dimensional metals YNiC2 and LuNiC2 including the investigation of transport, magnetotransport, galvanomagnetic, and specific heat properties. In YNiC2 we reveal two subsequent transitions associated with the formation of weakly coupled charge density wave at TCDW=318K and its locking in with the lattice at T1=275K. These characteristic temperatures follow the previously...
-
<i>N,N,N</i>-Trimethyl-N-(methyl 5-deoxy-2,3-<i>O</i>-isopropylidene-β-D-ribofuranosid-5- yl)ammonium 4-methylbenzenesulfonate sesquihydrate.
PublicationThe structure of the title compound, [C12H24NO4][C7H7O3S]·1.5H2O, contains alternating layers parallel to (001) of hydrophobic and polar character, stabilized by C-H...O hydrogen bonding. The furan ring adopts an envelope conformation with the C(OMe) atom as the flap, and the dioxolane ring is twisted about one of the O-C(methine) bonds. A comparison to related compounds is presented. The tosylate-O atoms were disordered over two...
-
Wpływ sposobu odwzorowania pojazdu szynowego na odpowiedź dynamiczną przęsła mostowego
PublicationW pracy przedstawiono rezultaty analiz numerycznych oraz badań eksploatacyjnych dwóch przęseł mostowych wymuszonych ruchomym pojazdem szynowym. Pojazd odwzorowano za pomocą czterech modeli uproszczonych: strumienia sił skupionych, strumienia mas skupionych oraz strumieni oscylatorów jedno- i dwumasowych. Analizy numeryczne wykonano przy wykorzystaniu MES. Potrzebne parametry dynamiczne wyznaczono na podstawie wyników identyfikacji...
-
Wastewater Engineering 2020/21 (Environmental Engineering, II stopnia, stacjonarne, II semestr))
e-Learning CoursesWastewater sources and flows Wastewater characterization based on physical and biodegradation criteria Preliminary treatment unit operations (screens, grit chambers, primary clarifiers) Biological processes (suspended growth vs. attached growth, hybrid systems, granular sludge) for wastewater treatment. Principles of biological nutrient removal (nitrification, denitrification, enhanced biological P removal, anammox). Implementation...
-
Effect of isovalent substitution on microstructure and phase transition of LaNb1−xMxO4 (M=Sb, V or Ta; x=0.05–0.3)
PublicationLaNb1−xMxO4 oxides with pentavalent elements of different ionic sizes (M=Sb, Ta and V, x=0.05–0.3) were synthesized by the solid state reaction method. Special interest was devoted to the antimony substituted lanthanum niobate which is a new material in this group. Rietveld analysis of the X-ray diffraction patterns was used to determine the influence of the material composition on unit cell parameters. On the basis of dilatometric...
-
Combined operation of 900MW power plant with the ORC through the bleed steam extraction point and CO2 recovery system
PublicationThe work presented here is aimed at utylisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90 C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach...
-
A Noded Carbon Emission Tool (NCET) to Measure Embodied Carbon (EC) in Compositional Cementitious Materials
PublicationThe ever evolving modern construction industry is now producing the highest levels of carbon content adversely affecting the construction associated environment. Although, the impact of carbon induced emission is quite large, but still not enough measurable standards and tools to scale these emission are available. This study contributes to the body of knowledge by providing a Grasshopper based definition to calculate the embodied...
-
Efficiency of European public higher education institutions: a two-stage multicountry approach
PublicationThe purpose of this study is to examine efficiency and its determinants in a set of higher education institutions (HEIs) from several European countries by means of non-parametric frontier techniques. Our analysis is based on a sample of 259 public HEIs from 7 European countries across the time period of 2001-2005. We conduct a two-stage DEA analysis (Simar and Wilson in J Economet 136:31-64, 2007), first evaluating DEA scores...
-
Revisiting Toroidal Dipolar Moment in Planar Metamaterial
PublicationThis article revisits the electric, magnetic, and toroidal dipolar moments in the metamaterial structure and presents the flatland design for generating a toroidal dipolar response for the electromagnetic plane wave at normal incidence. Based on the numerical analysis of the surface current, the electric field, the magnetic field, and the quantitative analysis of scattered power supported by the electromagnetic multipole theory,...
-
Recurrent Neural Network Based Adaptive Variable-Order Fractional PID Controller for Small Modular Reactor Thermal Power Control
PublicationThis paper presents the synthesis of an adaptive PID type controller in which the variable-order fractional operators are used. Due to the implementation difficulties of fractional order operators, both with a fixed and variable order, on digital control platforms caused by the requirement of infinite memory resources, the fractional operators that are part of the discussed controller were approximated by recurrent neural networks...
-
Novel MNZ-type microwave sensor for testing magnetodielectric materials
PublicationA novel microwave sensor with the mu-near-zero (MNZ) property is proposed for testing magnetodielectric material at 4.5 GHz. The sensor has a double-layer design consisting of a microstrip line and a metal strip with vias on layers 1 and 2, respectively. The proposed sensor can detect a unit change in relative permittivity and relative permeability with a difference in the operating frequency of 45 MHz and 78 MHz, respectively....
-
Accuracy, Memory and Speed Strategies in GPU-based Finite-Element Matrix-Generation
PublicationThis paper presents strategies on how to optimize GPU-based finite-element matrix-generation that occurs in the finite-element method (FEM) using higher order curvilinear elements. The goal of the optimization is to increase the speed of evaluation and assembly of large finite-element matrices on a single GPU (Graphics Processing Unit) while maintaining the accuracy of numerical integration at the desired level. For this reason,...
-
Wyznaczenie obciążeń na poszycie okrętu wywołanych uderzeniem fal i uderzeniem w lód i ich wpływ na bezpieczeństwo okrętu
PublicationThe main problem is the vessels rather accurate determination of the hydrodynamic loads so-called hydroelasticity outside . This can be done by theoretical analysis , computer simulation or by experiment. This gives the hydrodynamic pressure distribution on the walls of the ship's hull and also on the walls of marine vessels .The most dangerous are the impact of extreme storm waves , the impact of the wharf and the impact zone...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Perspectives on the replacement of harmful organic solvents in analytical methodologies: a framework toward the implementation of a generation of eco-friendly alternatives
PublicationVolatile organic solvents derived from non-renewable fossil feedstocks are commonplace in analytical laboratories. In spite of their convenient performance in countless unit operations, their environmental, health and safety issues represent a major area of concern. The progressive replacement of organic solvents obtained from fossil resources by eco-friendly alternatives would involve remarkable advances within the framework of...
-
Theoretical and Economic Evaluation of Low-Cost Deep Eutectic Solvents for Effective Biogas Upgrading to Bio-Methane
PublicationThis paper presents the theoretical screening of 23 low-cost deep eutectic solvents (DESs) as absorbents for effective removal of the main impurities from biogas streams using a conductor-like screening model for real solvents (COSMO-RS). Based on thermodynamic parameters, i.e., the activity coefficient, excess enthalpy, and Henry’s constant, two DESs composed of choline chloride: urea in a 1:2 molar ratio (ChCl:U 1:2), and choline...
-
Technology Concept of TLP Platform Towing and Installation in Waters with Depth of 60 m
PublicationThe article is part of the design and research work conducted at the Gdansk University of Technology, Faculty of Ocean Engineering and Ship Technology, in cooperation with a number of other research centres, which concerns offshore wind farms planned to be built in the Polish zone of the Baltic sea in the next years. One of most difficult tasks in this project is building suitable foundations for each power unit consisting of a...
-
Synthesis and antimicrobial activity of amino acid and peptide derivatives of mycophenolic acid
PublicationThe series of 16 novel amino acid and peptide mycophenolic acid (MPA) derivatives was obtained as potential antibacterial agents. Coupling of MPA with respective amines was optimized with condensing reagents such as EDCI/DMAP and T3P/TEA. Amino acid analogs were received both as methyl esters and also with the free carboxylic group. The biological activity of the products was tested on five references bacterial strains: Klebsiella...
-
Investigation of praseodymium and samarium co-doped ceria as an anode catalyst for DIR-SOFC fueled by biogas
PublicationThe Pr and Sm co-doped ceria (with up to 20 mol.% of dopants) compounds were examined as catalytic layers on the surface of SOFC anode directly fed by biogas to increase a lifetime and the efficiency of commercially available DIR-SOFC without the usage of an external reformer. The XRD, SEM and EDX methods were used to investigate the structural properties and the composition of fabricated materials. Furthermore, the electrical...
-
Single and Dual-GPU Generalized Sparse Eigenvalue Solvers for Finding a Few Low-Order Resonances of a Microwave Cavity Using the Finite-Element Method
PublicationThis paper presents two fast generalized eigenvalue solvers for sparse symmetric matrices that arise when electromagnetic cavity resonances are investigated using the higher-order finite element method (FEM). To find a few loworder resonances, the locally optimal block preconditioned conjugate gradient (LOBPCG) algorithm with null-space deflation is applied. The computations are expedited by using one or two graphical processing...
-
9-Cyano-10-methylacridinium hydrogen dinitrate
PublicationThe title compound, C15H11N2+·HN2O6−, crystallizes in the monoclinic space group C2/c with four molecules in the unit cell. The planar 9-cyano-10-methylacridinium cations lie on crystallographic twofold axes and are arranged in layers, almost perpendicular to the ac plane, in such a way that neighbouring molecules are positioned in a `head-to-tail' manner. These cations and the hydrogen dinitrate anions are linked through C—H⋯O...
-
Analysis of unsteady flow forces on the thermowell of steam temperature sensor
PublicationIn this paper, 3D numerical analysis of unsteady flow forces acting on the measuring sheath of steam temperature is presented. According to that purpose, the CFD (Computation Fluid Dynamic [1]) approach has been used. The nonstationary of fluid acting on the measuring sheath such as: Strouhal frequency, amplitude of pressure, structure of vortex, peak of pressure, field of pressure, field of velocity etc. are studied analytically...
-
Design and distribution of air nozzles in the biomass boiler assembly
PublicationDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
Impacts of Using Exhaust Gas Recirculation and Various Amount of Dimethyl Ether Premixed Ratios on Combustion and Emissions on a Dual-Fuel Compression Ignition Engine
PublicationIn the presented research, the authors dealt with the specific properties of the combustion process of dimethyl ether (DME) in a combustion car (Volkswagen Golf IV) engine AJM 1.9 TDI PDE made by Volkswagen factory. Dimethyl ether is an alternative fuel produced most often from natural gas, which can be used in compression ignition engines as a single fuel or co-burned with diesel oil. This work describes the impacts of using exhaust...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublicationThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Looking for a minimum exergy destruction in hierarchical cycle
PublicationThe paper presents results of energy analysis, complemented with an exergy balance, of hierarchical thermodynamic cycle. Proposed cycle is a binary vapour cycle based on a model of real supercritical steam power plant. Energy analysis is used to preliminary optimization of the cycle and the exergy losses analysis is proposed to perform optimization of heat transfer processes, which are essential for hierarchical cycles. Proposed...
-
Criteria for selection of working fluid in low-temperature ORC
PublicationThe economics of an ORC system is strictly linked to thermodynamic properties of the working fluid. A bad choice of working fluid could lead to a less efficient and expensive plant/generation unit. Some selection criteria have been put forward by various authors, incorporating thermodynamic properties, provided in literature but these do not have a general character. In the paper a simple analysis has been carried out which resulted...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublicationThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublicationIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Micellar aggregation of Triton X-100 surfactant in imidazolium ionic liquids
PublicationIn this work we investigated aggregation behavior of a nonionic surfactant Triton X-100 in eighteen imidazolium ionic liquids (ILs) with two to eight carbon atoms in cations alkyl chain, namely 1-ethyl-3-methylimidazolium, [EMIM], 1-butyl-3-methylimidazolium, [PrMIM], 3-methyl-1-propylimidazolium, [BMIM], 1-hexyl-3-methylimidazolium, [PMIM], 3-methyl-1-pentyl-imidazolium, [HMIM], and 1-octyl-3-methylimidazolium, [OMIM], and with...
-
Evaluati on of long-term start up costs impact on short-term price based operational optimization of a CCGT using MILP
PublicationAn increasing share of the weather-dependent RES generation in the power system leads to the growing importance of flexibility of conventional power plants. They were usually designed for base load operation and it is a challenge to determine the actual long-term cycling costs, which account for an increase in maintenance and overhaul expenditures, increased forced outage rates and shortened life expectancy of the plant and components....
-
Zero-Emissions, Off-grid, Autonomous Houseboat – a Case Study of Selected Locations in Europe
PublicationThe aim of this study was to assess the feasibility of creating a prototype of a self-sufficient houseboat that is capable of prolonged independence from power grids and freshwater sources. In this design, electricity demand is met by a photovoltaic installation, and the energy is stored in batteries. Fresh water for living needs may be obtained from many sources, depending on the environmental conditions, such as through purifying...
-
Circularly Polarized Metalens Antenna Design for 5G NR Sub-6 GHz Communication Systems
Publication5G NR (new radio) FR1 range refers to as Sub-6GHz band (410MHz to 7125MHz and 3.4GHz to 6GHz). In this paper, the frequency range of interest is from 3.4 to 6GHz, as many cellular companies are focusing on this Sub-6GHz band. A wideband circularly polarized (CP) antenna radiator is designed with diamond shape patches, fed by a microstrip line at the bottom through a rectangular shape wide slot on a ground plane. The proposed CP...
-
Local Conformation and Cocrystallization Phenomena in Renewable Diaminoisoidide-Based Polyamides Studied by FT-IR, Solid State NMR, and WAXD
PublicationBiobased polyamides synthesized from diaminoisoidide (DAII), 1,4-diaminobutane, and sebacic acid are investigated by FT-IR, 13C{1H} magic-angle spinning/cross-polarization (CP/MAS) NMR spectroscopy, and WAXD. Their molecular conformation and mobility undergo distinct changes as a function of temperature and diaminoisoidide content in the compositions. The presence of randomly distributed diaminoisoidide (DAII) in the polyamides...
-
Projekt Fakultatywny II/ Elective Design II 2020/2021 S.Hudnik+K.Życzkowska
e-Learning CoursesSUPERSURFACE – an alternative model for life The studio will explore an alternative architectural models for contemporary society in the context of different political, cultural, economic and environmental contexts. Temporal living and technology links the general fashion principles with architecture. The projects will investigate the visionary scenarios through Superstudio movies Fundamental Acts and various concepts and structures...
-
Research of electric drive systems with real time software configurable control
PublicationПредмет исследования. Представлен учебно-лабораторный стенд для исследования систем управления элек- троприводами. Стенд используется для обучения студентов системам управления электроприводами и предна- значен для повышения эффективности усвоения материала. Метод. В основу предлагаемого решения положен метод взаимного нагружения электрических машин, питаемых от силовых преобразователей с общим звеном постоянного тока. Это позволяет...
-
A concept of Signal Equalization Method Based on Music Genre and the Listener's Room Characteristics
PublicationA research study that investigates the influence of the room acoustics environment on the frequency characteristic of the audio signal playback is presented. First, a novel spectral equalization method of the room acoustic conditions is introduced. On the basis of the frequency response of the room, a system for room acoustics compensation based on eight-band equalizer is proposed. The system settings depend on music genre. In...
-
Processes of enhancing the intelligence of Learning Organizations on the basis of Competence Centers
PublicationThe process of organizational learning and proper knowledge management became today one of the major challenges for the organization acting in the knowledge-based economy. According to the observations of the authors of this paper the demand for formalization of knowledge management processes and organizational learning is particularly evident in research institutions, established either by the universities, or the companies. The...
-
Release of potassium from actvated sludge as a resultof use peroxyacetic acid = Uwalnianie potasu z osadu czynnego pod wpływem kwasu nadoctowego
PublicationThe phenomenon of potassium efflux (GGKE - glutathione-gated potassium efflux) from the calls of activated sludge bacteria in the result of peroxyacetic acid (CH3CO3H) dosing was investigated. Addition of the strong oxidant to the activated sludge environment caused activation of the defense mechanisms of bacterial cells, related to glutathione transformations, which resulted in the significant increase of potassium ions concentration....
-
Methods of Determining Pressure Drop in Internal Channels of a Hydraulic Motor
PublicationIn this paper, new methods for determining the pressure drop in internal channels of a hydraulic motor are proposed and described. Mathematical models of pressure losses in internal channels have also been described. Experimental tests of the satellite motor were carried out according to one of the proposed methods. The tests were carried out for two liquids, i.e., water and mineral oil. Experimental studies have shown that at...
-
A Pilot Study on Machining Difficult-to-Cut Materials with the Use of Tools Fabricated by SLS Technology
PublicationThe growing use of contemporary materials in various industrial sectors, such as aerospace, automotive, as well as the oil and gas industry, requires appropriate machining methods and tools. Currently, apart from the necessity to obtain high-dimensional and shape accuracy, the efficiency and economic aspects of the selected manufacturing process are equally important, especially when difficult-to-cut materials, such as hard and...
-
On Decomposition-Based Surrogate-Assisted Optimization of Leaky Wave Antenna Input Characteristics for Beam Scanning Applications
PublicationRecent years have witnessed a growing interest in reconfigurable antenna systems. Travelling wave antennas (TWAs) and leaky wave antennas (LWAs) are representative examples of structures featuring a great level of flexibility (e.g., straightforward implementation of beam scanning), relatively simple geometrical structure, low profile, and low fabrication cost. Notwithstanding, the design process of TWAs/LWAs is a challenging endeavor...
-
Additive Manufacturing as a Solution to Challenges Associated with Heat Pipe Production
PublicationThe aim of this review is to present the recent developments in heat pipe production, which respond to the current technical problems related to the wide implementation of this technology. A novel approach in HP manufacturing is to utilise hi-tech additive manufacturing techniques where the most complicated geometries are fabricated layer-by-layer directly from a digital file. This technology might be a solution to various challenges...
-
Preparatory Railway Track Geometry Estimation Based on GNSS and IMU Systems
PublicationThe article discusses an important issue of railway line construction and maintenance, which fundamentally is the verification of geometric parameters of the railway track. For this purpose, mobile measurements have been performed using a measuring platform with two properly arranged GNSS receivers, which made it possible to determine the base vector of the platform. The measuring functionality of the system was extended by IMU....
-
Thin-walled frames and grids - statics and dynamics
PublicationFrames and grids assembled with thin-walled beams of open cross-section are widely applied in various civil engineering and vehicle or machine structures. Static and dynamic analysis of theses structures may be carried out by means of different models, startingfrom the classical models made of beam elements undergoing the Kirchhoff assumptions to the FE discretization of whole frame into plane elements. The former model is very...
-
Innovation in the strategies of Polish provinces - a comparative study of selected cases
PublicationMany strategic management theorists and practitioners believe that the implementation of innovation is one of the key factors determining the company success and show the relationship between long-term innovation strategy and business development strategy. It has also been claimed that similar strategies should be developed for each unit of public administrationMinistry of Economy has set National Development Strategy 2007-2015...