Filters
total: 3308
filtered: 1689
displaying 1000 best results Help
Search results for: connection stiffnes
-
An approach for the response of buildings subjected to impact load after soft-story failure due to earthquake excitation
Publicationhe soft-story failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an intermediate soft story of a structure results in large impact loading acting on the lower floors due to the fall of the upper stories. The aim of the present paper is to study the behavior of the structural members exposed to such extreme load conditions occurring under ground motion excitation. Special...
-
Application of probabilistic tools to extend load test design of bridges prior to opening
PublicationLoad tests of bridges are widely performed in a large number of countries. Deterministic comparison of measurement results to the theoretical, FEM (finite element method)-based outcomes with possible further calibration is mostly applied. Sometimes, the data collected in the tests are also used to calibrate the reliability factors of bridge structures or their components. This work proposes to complement the stage of the load test...
-
Układ kompensacji wpływu wzniesienia oraz przyspieszenia w przyczepie do badania oporu toczenia
PublicationW artykule przedstawiono metodę pomiaru współczynnika oporu toczenia przy wykorzystaniu przyczepy opracowanej w Zakładzie Pojazdów na Politechnice Gdańskiej. Następnie omówiono opatentowany układ bezwładnościowy do korekcji wpływu wzniesienia oraz metodę korekcji wpływu przyspieszenia wzdłużnego. W dalszej części przedstawiono przykładowe wyniki obrazujące pomiar współczynnika CRR na wzniesieniu przy zmiennej prędkości.
-
Modeling of Composite Shells in 6-Parameter Nonlinear Theory with Drilling Degree of Freedom
PublicationWithin the framework of a 6-parameter nonlinear shell theory, with strain measures of Cosserat type, constitutive relations are proposed for thin elastic composite shells. The material law is expressed in terms of five engineering constants of classical anisotropic continuum plus an additional parameter accounting for drilling stiffness. The theory allows for unlimited displacements and rotations. A number of examples are presented...
-
Behaviour of orthotropic surgical implant in hernia repair due to the material orientation and abdomen surface deformation
Publicationrelation to the different range of typical deformations observed in different directions and zones of abdomen surface due to the patients’ life activities, has a significant influence on the extreme junction forces in the mesh–tissue connections and hence the repair persistence. The finite element model of the orthotropic implant was developed, and the junction forces in the connections of tissue and mesh were studied. The kinematical...
-
The landscape in the informal education of the youngest
PublicationThe European Landscape Convention, adopted in 2000, aims to promote the protection, management and planning of landscapes and to organise cooperation on landscape-related issues. Countries that ratified the Convention undertook to introduce activities that would promote public education on the subject. In Poland, the Ministry of Education has identified schools as the place to implement...
-
Rapid EM-driven antenna dimension scaling through inverse modeling
PublicationIn this letter, a computationally feasible technique for dimension scaling of antenna structures is introduced. The proposed methodology is based on inverse surrogate modeling where the geometry parameters of the antenna structure of interest are explicitly related to the operating frequency. The surrogate model is identified based on a few antenna designs optimized for selected reference frequencies. For the sake of computational...
-
Evaluating Asymmetric N-Grams as Spell-Checking Mechanism
PublicationTypical approaches to string comparing marks two strings as either different or equal without taking into account any similarity measures. Being able to judge similarity is however required for spelling error corrections, as we want to find the best match for a given word. In this paper we present a bi2quadro-grams method for spelling errors correction. The method proposed uses different n-grams dimension for the source (checked)...
-
A measurement method for lossy capacitive relative humidity sensors based on a direct sensor-to-microcontroller interface circuit
PublicationA new time-domain measurement method for determining the capacitance and resistance values of lossy relative humidity capacitive sensors is presented. The method is based on a direct sensor-to-microcontroller interface for microcontrollers with internal analog comparators and timers. The interface circuit consists only of four reference resistors (two reference resistors if a microcontroller includes a voltage reference source),...
-
The application of microscopic models in the study of pedestrian traffic
PublicationCities (especially in Central and Eastern Europe) focus on improving the road network, which aims to improve the efficiency of motor traffic and minimize congestion. Most of existing tools for analysing the effectiveness of urban transport networks do not assume to analyse the impact of walking and cycling on efficiency of transport systems. It is therefore necessary to develop solutions...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublicationNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Fault diagnosing system of wheeled tractors
PublicationA defect of complex wheeled tractor assembles most frequently negative influence on exploitation efficiency, safety and exhaust gases emission. Structure complexity of wheeled tractors requires more and more advanced diagnostic methods for identification of their serviceable possibilities as well in manufacturing step as in exploitation. In classical diagnosing methods of wheeled tractor defects states mapping by measured diagnostic...
-
Spin and Orbital Effects on Asymmetric Exchange Interaction in Polar Magnets: M(IO3)2 (M = Cu and Mn)
PublicationMagnetic polar materials feature an astonishing range of physical properties, such as magnetoelectric coupling, chiral spin textures, and related new spin topology physics. This is primarily attributable to their lack of space inversion symmetry in conjunction with unpaired electrons, potentially facilitating an asymmetric Dzyaloshinskii–Moriya (DM) exchange interaction supported by spin–orbital and electron–lattice coupling. However,...
-
3D buckling analysis of a truss with horizontal braces
PublicationThe present research is devoted to the study of out-of-plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor ¼. A linear buckling and a non-linear analysis with geometric and material nonlinearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness...
-
THE USE OF GREEN LOGISTICS ELEMENTS DURING THE CONSTRUCTION OF OFFSHORE VESSELS
PublicationThe article is aimed at the presentation referring to the use of green logistics elements during the construction of the offshore vessels in the following aspects: collection, removal and utilisation of any waste that is harmful for natural environment, elimination of the negative impact that such waste can have on natural environment and the search for the optimal solutions as regards these aspects.
-
Modal analysis of temporary steel grandstand equipped with different bracing systems
PublicationThe aim of this paper is to present the results of numerical analysis focused on temporary steel scaffolding grandstand. The investigation has been devoted to modal analysis where modes of free vibrations and corresponding natural frequencies have been estimated and compared. The structure was equipped with different types of stiffener members. One on them is a typical tubular stiffener, while the second one is spe-cially designed...
-
The Impact of Wind Generation on the Transmission System
PublicationThis article has been published to investigate the im-pact of the wind power on the power system- this is a system dependent issue that requires to perform sys-tem specific impact study. This paper discusses the impact of power flow, short circuit current, power quali-ty, voltage stability and the power system during the connection of a wind farm into transmission system. W referacie omówiono wpływ farm wiatrowych na pracę systemu...
-
Practical aspects of testing superconducting electromagnets by the capacitor discharge method taking into account the non-linearity of circuit parameters
PublicationThe article presents selected issues related to the development and testing of the diagnostics systems dedicated for superconducting electromagnets. The systems were constructed to assess the production quality of superconducting electromagnets of the SIS100 synchrotron, a new accelerator being built as part of the Facility of Antiproton and Ion Research (FAIR). One of the systems is used for automatic checking of electrical connection...
-
Distributed state estimation using a network of asynchronous processing nodes
PublicationWe consider the problem of distributed state estimation of continuous-time stochastic processes using a~network of processing nodes. Each node performs measurement and estimation using the Kalman filtering technique, communicates its results to other nodes in the network, and utilizes similar results from the other nodes in its own computations. We assume that the connection graph of the network is not complete, i.e. not all nodes...
-
Mechanical compatibility of implants used in hernia repair with abdominal wall
PublicationThe paper deals with a membrane model of a synthetic surgical mesh for treatment of abdominal hernia. The authors analyse the compatibility of two implant types with the human wall: Dualmesh Gore and Proceed. The finite element method is applied to simulate tjhe behavior of the proposed model. Due fact that recurrences are usually caused by connection failure, this study is focused on reaction forces in supports representing the...
-
Distributed state estimation using a network of asynchronous processing nodes
PublicationWe consider the problem of distributed state estimation of continuous-time stochastic processes using a~network of processing nodes. Each node performs measurement and estimation using the Kalman filtering technique, communicates its results to other nodes in the network, and utilizes similar results from the other nodes in its own computations. We assume that the connection graph of the network is not complete, i.e. not all nodes...
-
The conducted EMI in DC-DC converters
PublicationThis book presents the phenomena of conducted electromagnetic interference (EMI) generation in DC-DC converters. The measurement and simulation are used to analyze the impact of the most important parameters on the character, level and propagation path of interference. In this book, the analysis of the interference generation and propagation is presented on the example of three basic converters. The wide banded behavior of all...
-
Experimental investigations on concrete beams reinforced with CFRP lamellas
PublicationPaper presents experimental investigation made on two concrete beams reinforced with internal Carbon Fibre Reinforced Polymer (CFRP) lamellas (i.e. strips, bands). The reinforcement geometrical arrangement was similar as in normal concrete beams reinforced with steel bars and stirrups. The beams were destroyed by the shear forces, as intended. Obtained load-carrying capacities were lower as expected: below 40% of a calculated value....
-
Strong ellipticity conditions and infinitesimal stability within nonlinear strain gradient elasticity
PublicationWe discuss connections between the strong ellipticity condition and the infinitesimal instability within the nonlinear strain gradient elasticity. The strong ellipticity (SE) condition describes the property of equations of statics whereas the infinitesimal stability is introduced as the positive definiteness of the second variation of an energy functional. Here we establish few implications which simplify the further analysis...
-
Testbed for development and verification of hybrid localization systems
PublicationIn this paper a testbed for development and verification of hybrid localization systems is presented. It allows for systematic analysis of hybrid localization methods and speed up the development of new schemes. The proposed testbed platform is composed of subsystem for sequential data collection and testing infrastructure that can be used for investigating the localization mechanisms in controllable environment.
-
The multiscalar control of induction motor with the sliding mode controllers
PublicationThe control structure of induction motor is proposed in this paper. The structure of multiscalar control with conventional PI - controllers is well known in literature. The sliding mode multiscalar control (SMMC) conception is presented in this paper. The induction motor is fed by voltage source inverter. Comparison between two multiscalar control method is showed.
-
A procedure for the identification of effective mechanical parameters of additively manufactured elements using integrated ultrasonic bulk and guided waves
PublicationThe subject of the current work was a simple but robust novel two-stage procedure for the non-destructive determination of effective elastic constants using ultrasonic wave propagation. First, ultrasonic bulk wave velocities measured on cubic samples were used to calculate most of the elements of the stiffness matrix. Secondly, the remaining elements were determined using the dispersion curves of elastic guided waves measured on...
-
Modelling tunnelling-induced deformation in stiff soils with a hyperelastic–plastic anisotropic model
PublicationIn this paper, the tunnelling-induced deformation in anisotropic stiff soils is analysed using FE modelling. The influence of material description is investigated rather than an advanced simulation of the tunnelling method. A new hyperelastic– plastic model is proposed to describe the anisotropic mechanical behaviour of stiff highly overconsolidated soil. This model can reproduce the superposition of variable stress-induced anisotropy...
-
Research on operational characteristics of tyres with run flat insert
PublicationThe paper describes results of research on heavy vehicle tyre with Run Flat VFI insert. The experiment has included the determination of heat generation, rolling resistanceand radial stifnessof two different tyre designes (textile and steel carcass). The results have been used for the purpose of ewalution of tyre operating characteristics. The study included research on non-inflated tyre properties. The purpose of the paper is...
-
Collision‐Aware Routing Using Multi‐Objective Seagull Optimization Algorithm for WSN‐Based IoT
PublicationIn recent trends, wireless sensor networks (WSNs) have become popular because of their cost, simple structure, reliability, and developments in the communication field. The Internet of Things (IoT) refers to the interconnection of everyday objects and sharing of information through the Internet. Congestion in networks leads to transmission delays and packet loss and causes wastage of time and energy on recovery. The routing protocols...
-
A pore-scale thermo–hydro-mechanical model for particulate systems
PublicationA pore scale numerical method dedicated to the simulation of heat transfer and associated thermo–hydro-mechanical couplings in granular media is described. The proposed thermo–hydro-mechanical approach builds on an existing hydromechanical model that employs the discrete element method for simulating the mechanical behavior of dense sphere packings and combines it with the finite volume method for simulating pore space fluid flow...
-
Positron Scattering and Annihilation in Organic Molecules
PublicationIn this paper, we address the problem of connecting positron lifetimes in liquids with collision cross sections in gases. We present the analyses of annihilation lifetime spectra of positrons in the liquid benzene, c-hexane, n-hexane, methanol and ethanol and calculations of scattering cross sections of positrons with benzene and c-hexane in the gas phase.
-
Dekodowanie kodów iterowanych z użyciem sieci neuronowej
PublicationNadmiarowe kody iterowane są jedną z prostych metod pozyskiwania długich kodów korekcyjnych zapewniających dużą ochronę przed błędami. Jednocześnie, chociaż ich podstawowy iteracyjny dekoder jest prosty koncepcyjnie oraz łatwy w implementacji, to nie jest on rozwiązaniem optymalnym. Poszukując alternatywnych rozwiązań zaproponowano, przedstawioną w pracy, strukturę dekodera tego typu kodów wspomaganą przez sieci neuronowe. Zaproponowane...
-
Chapter 8 – Active Sampling of Air
PublicationThis chapter reviews the literature information on analytical techniques and laboratory equipment used for active sampling of air (atmospheric and indoor) in regular monitoring research. It describes popular analytical devices applied for sample collection using various types of polymeric bags, e.g. Tedlar bags, Teflon or Nafion bags, and/or stainless steel vacuum containers. It reviews literature data about the application of...
-
Experimental and numerical investigations of ultimate strength of degradated structures
PublicationThe presented work investigates the corrosion influence on the structural behaviour of structural elements. Nine welded large-scale stiffened plates, and 30 standard small specimens have been subjected to the accelerated marine immersed conditions. After corrosion testing, the specimens have been accurately measured in terms of surface characteristics. The coupon specimens were furtherly subjected to tensile loading to develop...
-
Reactive Energy Billing in Operator Tariffs in Poland
PublicationThe paper describes the current method of reactive energy billing in the tariffs of distribution grid operators in Poland. The current solutions are subject to critical assessment. Issues related to the motivation effect of the current solutions on consumers are analysed. Problems that occur in relation with connecting distributed generators to the distribution grid and challenges related to prosumer billing are indicated.
-
Mechanical properties of Precontraint 1202 S2 based on uniaxial tensile and creep tests
PublicationThe purpose of the paper is the estimation of the polyvinyl chloride – polyester-coated fabric (Precontraint 1202 S2) mechanical properties under uniaxial tensile tests as well as short- and long-time creep tests. The uniaxial tests are the basis of non-linear elastic description while the creep tests are used for the evaluation of the stiffness parameters in time and for the identification of the standard viscoelastic model. The...
-
3D Buckling Analysis of a Truss with Horizontal Braces
PublicationThe present research is devoted to the study of out–of–plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor 1=4. A linear buckling and a non–linear analysis with geometric and material non–linearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness condition...
-
A novel genetic approach to provide differentiated levels of service resilience in IP-MPLS/WDM networks
PublicationThis paper introduces a novel class-based method of survivable routing for connection-oriented IP-MPLS/WDM networks, called MLS-GEN-H. The algorithm is designed to provide differentiated levels of service survivability in order to respond to varying requirements of end-users. It divides the complex problem of survivable routing in IP-MPLS/WDM networks into two subproblems, one for each network layer, which enables finding the...
-
On the exact equilibrium conditions of irregular shells reinforced by beams along the junctions
PublicationThe exact, resultant equilibrium conditions for irregular shells reinforced by beams along the junctions are formulated. The equilibrium conditions are derived by performing direct integration of the global equilibrium conditions of continuum mechanics. New, exact resultant static continuity conditions along the singular curve modelling reinforced junction are presented. The results do not depend on shell thickness, internal through-the-thickness...
-
Euro 2012 in Gdańsk, Poland. Is it worth using public funds?
PublicationThe aim of this study is to estimate the willingness - to - pay (WTP) among the community of the Pomeranian region, Poland in connection with intangible benefits and costs st emming from hosting the Euro 2012 in Gdansk. A survey conducted among 407 respondents was the source of information. The results of the study show that the average value of WTP benefit for the whole sample was 45,72 PLN2012 and WTP cost...
-
Water related esthetics - the phenomenon of new structure in the post industrial shipyard areas
PublicationDirection of the main movements that are made in the European cities determines not only structural but also an esthetic changes. Paper follows the topic of visual diversity of post industrial waterfront cities and it’s relation to the local identity and cultural changes that are provided. Reshaping of the cities continuously proceed. Are those changes related with industrial shipyard districts only economical and spatial or also...
-
Control system for contactless electrical energy transfer with varying air gap
PublicationInductive power transfer (IPT) is a system by which electrical energy may be transmitted without electrical connection through a large air gap between coils. Systems usually considered in the literature are the ones with a constant air gap. The paper describes the analysis of IPT, which allows for supplying an electrical load in the conditions of slow, in relation to the dynamics of power supply, changes in the dimensions of the...
-
Low-Loss Mechanically Tunable Resonator and Phase Shifters in Groove Gap Waveguide Technology
PublicationThis research is focused on the design and realization of high-performance high-power variable phase shifters in groove gap waveguide technology. Specifically, it is shown that the unique characteristic of groove gap waveguides, which is its proper operation without the need for electrical connection between the top and bottom sections of the waveguide, can be used to design mechanically tunable devices. Using the proposed method,...
-
Routing Method for Interplanetary Satellite Communication in IoT Networks Based on IPv6
PublicationThe matter of interplanetary network (IPN) connection is a complex and sophisticated topic. Space missions are aimed inter alia at studying the outer planets of our solar system. Data transmission itself, as well as receiving data from satellites located on the borders of the solar system, was only possible thanks to the use of powerful deep space network (DSN) receivers, located in various places on the surface of the Earth. In...
-
Stock Markets’ Reactions to the Announcement of the Hosts. An Event Study in the Analysis of Large Sporting Events in the Years 1976–2032
PublicationThis study attempts to estimate the impact of the announcements of hosts of large sporting events on domestic stock markets. The research problem is to establish a connection between the uniqueness of a sporting event and investors’ beliefs through stock price behavior. Using appropriate estimation windows, 13 different sporting events classified as large, including mega and major events, were tested. The obtained results show...
-
The dependence of linear viscoelasticity limits of cold-recycled mixtures on time of curing and compaction method
PublicationCold-recycled mixtures are currently among the most widely used and investigated methods that enable recycling of old pavement structures in an environmentally friendly manner. Upon milling, the old pavement structure – whose gradation can be improved with addition of virgin aggregate – is mixed and compacted at ambient temperature. The main binding agents are bituminous emulsion and cement. Due to their dual binding behaviour,...
-
Interactive Information Retrieval Algorithm for Wikipedia Articels
PublicationThe article presents an algorithm for retrieving textual information in documents collection. The algorithm employs a category system that organizers the repository and using interaction with user improves search precision. The algorithm was implemented for simple English Wikipedia and the first evaluation results indicates the proposed method can help to retrieve information from large document repositories.
-
WARUNKI REZONANSOWE W WĘŹLE Z KOMPENSATOREM SVC
PublicationInstalowanie kompensatorów statycznych w sieciach rozdzielczych i przesyłowych służy poprawie profili napięciowych. Kompensatory jako źródła mocy biernej zwiększają stabilność napięciową systemu. Pozwalają także na szybszą odbudowę systemu w przypadku awarii napięciowej. W artykule zaprezentowano wpływ struktury i wysterowania układu SVC na zmianę impedancji w układzie zasilania. Ma to bezpośredni wpływ na częstotliwości, przy...
-
Opracowanie procedury i badania wytrzymałościowe połączeń spawanych pomiędzy rurą kwadratowa a elementami giętymi na zimno ze stali S355 oraz testowanie połączeń o grubości 4, 6, 8mm typu S355
PublicationCelem pracy było: - opracowanie procedury badania wytrzymałości połączeń spawanych rozciąganych w kierunku prostopadłym i w kierunku równoległym (ścinanych) do osi spoiny. Spoiny te łączyły elementy rur kwadratowych o różnej grubości z elementami w kształcie ceownika giętymi na zimno. - wykonanie próbek do badań wytrzymałościowych wyciętych z elementów spawanych dostarczonych przez Zakład Produkcyjny firmy Borga obciążonych prostopadle...