Filters
total: 3372
filtered: 2330
displaying 1000 best results Help
Search results for: mesurments
-
Proposal of a System Loss Model for Body Area Network in Passenger Ferry Environment
PublicationIn the paper, proposal of an empirical off-body system loss model for Body Area Networks working in a passenger ferry environment at 2.45 GHz has been presented. The measurements were carried out for dynamic scenarios in the discotheque passenger ferry environment. The general model formula consists of three components: mean system loss, attenuation resulting from the variable antenna position on the human body, and attenuation...
-
Accuracy analysis of 3D model obtained by photogrammetric method on the example of historic room from Wisłoujście Fortress
PublicationThe article presents a comparison of obtained models of a test object. Close range photogrammetry was used to obtain 3D models. As test object was used one of the rooms located in Wisłoujście Fortress in Gdańsk, Poland. Different models were obtained by using different distribution and number of reference points. Article contains analysis of differences between coordinates of control points obtained from total station measurements...
-
Investigation of energy deposition and its optical imaging in polymer gel dosimeters
PublicationThis following chapter describes methods for verifying the absorbed dose during radiotherapy. Special attention is paid to the method using polymer-gel dosimeters, the dose reading of which is performed by means of Laser Computed Tomography. The chapter also includes considerations on alternative solutions for dosimetric measurements and various types of radiotherapy and their pros and cons. In addition, both the methods of structural...
-
Pomiar wartości opóźnienia hamowania dla sprawnego i niesprawnego układu hamulcowego
PublicationW artykule przedstawiono wyniki badań: sprawny układ hamulcowy i niesprawny układ hamulcowy. Pomiary opóźnienia hamowania przeprowadzono na suchej nawierzchni asfaltowej. Wykonano układ, który rozszczelnia przewód hamulcowy przy przednim prawym kole w czasie jazdy. Wykonano symulację wycieku płynu hamulcowego
-
THE METHOD OF MEASURING THE MEMBRANE COVER GEOMETRY USING LASER SCANNING AND SYNCHRONOUS PHOTOGRAMMETRY
PublicationThe authors present the experience and results of field studies carried out at the technical acceptance of Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland). An unusual design of covering made in the form of “Sheerfill I” technical fabric membrane required spanned in the form of sails, required the use of terrestrial laser scanning. Such approach allowed for the fast and accurate record of the surface of individual panels...
-
Modelowanie wymiany wody w zbiornikach hodowlanych przy użyciu zmodyfikowanego modelu tłokowego na przykładzie basenów hodowlanych dla fok
PublicationNiniejszy artykuł opisuje sposób prostego modelowania wymiany wody w basenach hodowlanych fokarium Stacji Morskiej Instytutu Oceanografii Uniwersytetu Gdańskiego. W celu rozpoznania warunków wymiany wody oraz udziału stref zastoiskowych w basenach posłużono się dwiema uzupełniającymi się metodami. Były to badania traserowe z wykorzystaniem znacznika fluororescencyjnego oraz komputerowe obliczenia rozkładu linii prądu z użyciem...
-
Tracking Moving Objects in Video Surveillance Systems with Kalman and Particle Filters – A Practical Approach
PublicationThis Chapter focuses on the first type of object tracking algorithms, namely on Kalman and particle filters. A theory of these algorithms may be found in many publications, there are also reports on implementation of these approaches to object tracking in video. However, developers of VCA systems still face two important problems. The first one is related to obtaining accurate measurements of positions and sizes of the tracked...
-
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublicationIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
The shallow sea experiment with usage of linear hydrophone array
PublicationPurpose of this article is to present designed and made linear hydrophone array and the results obtained during in situ trails on Gulf of Gdańsk. The measuring system allowed to localize hydrophones in the selected points and perform measurements in both the horizontal antenna positioning and vertical. Made in this way recordings allow creating accurate 3D imaging of sound intensity/propagation. During research three floating objects...
-
Speed dependency of temperature effects on road traffic noise
PublicationRecently, a new literature review on the influence of temperature on tire/road noise became available, based on a compilation of large amounts of data from empirical research. This review showed that the effect of temperature is roughly double of that previously assumed and taken account of in international standards. This makes temperature one of the main sources of error in measurement results. Furthermore, it suggested that...
-
LOW NOISE TIRES FOR HYBRID AND ELECTRIC VEHICLES
PublicationLow Emission Vehicles that are hybrid and electric cars may benefit from specially designed tires that are optimized for driving conditions typical for such vehicles. It is possible that in the future Low Emission Vehicles, especially passenger cars, will substitute conventional vehicles in all applications, however for the time being they are mostly used in urban and suburban areas. Urban traffic has a rather low demand for grip...
-
The best porous asphalt pavement in Sweden so far
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Low energy elastic scattering of electrons from hexafluoropropene (C3F6)
PublicationWe present cross sections from a joint experimental and theoretical study on elastic electron scattering from hexafluoropropene (C3F6) in the gas phase. The experimental results, using low energy electron spectroscopy, were obtained at incident electron energies of 0.5, 1, 1.5, 2, 3, 4, 5, 6, 10, 12, 15 and 20 eV, for scattering angles ranging from 10°to 130°. The theoretical method used in the computation of the integral, momentum...
-
Evaluation of Connectivity Gaps Impact on TCP Transmissions in Maritime Communications
PublicationMany organizations and research working groups, including among others IEEE, ITU, ETSI and IMO are currently working towards improvements in communication of different types of vehicles (cars, trains, planes and vessels) and upgrading utilities and services offered to their crews and passengers travelling all over the world. The paper deals with selected aspects of the TCP protocol connectivity in maritime wireless networks. The...
-
Effective density of airborne wear particles from car brake materials
PublicationPeople living in urban environments are subject to high health risks due to various anthropogenic sources of airborne particulate matter, including wear of transport vehicle brakes. Studies of airborne particles often require an estimate of the effective particle density, a property that allows correct matching of mass and size characteristics measured by different aerosol instruments. In this study we investigated the effective...
-
Structural and physical characterization of NpPt2In7
PublicationA new neptunium intermetallic compound, NpPt2In7, has been synthesized in polycrystalline form and characterized by several macroscopic techniques. A Rietveld analysis of its powder x-ray diffraction pattern shows that NpPt2In7 crystallizes in a tetragonal lattice with I4/mmm symmetry and lattice parameters a = 4.58471(3) Å, c = 21.5065(3) Å. Magnetic susceptibility, electrical resistivity, Hall effect, and heat capacity measurements indicate...
-
Synthesis and physical properties of the 10.6 K ferromagnet NdIr3
PublicationThe magnetic, transport, and thermodynamic properties of NdIr3 are reported. Its PuNi3-type crystal structure (space group R−3m), with lattice parameters a= 5.3262(1)Å and c=26.2218(3)Å, was confirmed by powder x-ray diffraction. Our measurements indicate that NdIr3 exhibits a previously unreported paramagnetic to ferromagnetic phase transition below TC=10.6 K(determined by using the Arrott plot). The magnetic susceptibility obeys...
-
The Optical Coherence Tomography and Raman Spectroscopy for Sensing of the Bone Demineralization Process
PublicationThe presented research was intended to seek new optical methods to investigate the demineralization process of bones. Optical examination of the bone condition could facilitate clinical trials and improve the safety of patients. The authors used a set of complementary methods: polarization-sensitive optical coherence tomography (PS-OCT) and Raman spectroscopy. Chicken bone samples were used in this research. To stimulate in laboratory...
-
A Numerical Study on Baseline-Free Damage Detection Using Frequency Steerable Acoustic Transducers
PublicationIn structural health monitoring (SHM) a considerable amount of damage detection algorithms based on guided waves (GW) have been developed. Most of them rely on extensive transducer networks, besides preliminary reference measurements of the structures. This originated a growing demand for hardware simplification and cost reduction of the wave-based SHM methods, driving the conception of new solutions enabling both: the reduction...
-
STAN AWARYJNY TRYBUNY STADIONU W ZIELONEJ GÓRZE WYWOŁANY SYNCHRONICZNYM TAŃCEM KIBICÓW
PublicationW artykule przedstawiono badania i naprawy trybuny stadionu żużlowego w Zielonej Górze narażonej na nadmierne drgania podczas synchronicznego tańca kibiców zwanego „Labado”. W trakcie prac wykonano dwa etapy wzmocnień: za pomocą dodatkowych słupków (zalecenie zespołu z Uniwersytetu Zielonogórskiego) oraz wzmocnienie dodatkowymi stężeniami całej konstrukcji zadaszenia trybuny. W artykule przedstawiono wyniki badań pomiarowych in...
-
STAN AWARYJNY TRYBUNY STADIONU W ZIELONEJ GÓRZE WYWOŁANY SYNCHRONICZNYM TAŃCEM KIBICÓW
PublicationW artykule przedstawiono badania i naprawy trybuny stadionu żużlowego w Zielonej Górze narażonej na nadmierne drgania podczas synchronicznego tańca kibiców zwanego „Labado”. W trakcie prac wykonano dwa etapy wzmocnień: za pomocą dodatkowych słupków (zalecenie zespołu z Uniwersytetu Zielonogórskiego) oraz wzmocnienie dodatkowymi stężeniami całej konstrukcji zadaszenia trybuny. W artykule przedstawiono wyniki badań pomiarowych in...
-
Niepewność wyniku analizy - sposób obliczania
PublicationW pracy przedstawiono sposób obliczania niepewności wyniku analizy zalecany przez EURACHEM. Zamieszczono także podstawowe terminy i definicje, które są stosowane przy konsultowaniu budżetu niepewności i obliczaniu niepewności całkowitej. Praca powstała na podstawie doświadczeń autora w trakcie 2 letniego stażu podoktorskiego, odbytego w Institute for Reference Materials and Measurements w Geel (Belgia), jednym z laboratoriów Komisji...
-
Modelling of steady state and transient performance of the synchronous generator considering harmonic distortions caused by non-uniform saturation of the pole shoe
PublicationIn this paper a synchronous generator model is described. This model is developed on the assumption that in loaded and no load conditions the saturation effect affects the pole shoe in a different way. The developed model is based on the multiple saliency model and is formulated using winding function approach in machine variables. The influence of the non-uniform saturation of the pole shoe in load conditions on the performance...
-
Factory Acceptance Test – Strain Gauge Measurement, Report no: WOiO /II/123/2014
PublicationTested object was 40 meters long jib and its foundation, placed in Gdansk Shiprepair Yard, manufactured by KMK. The contruction was dedicated to the passenger cruise vessel "Quantum of the Seas" The Strain Gauge measurement in different location and load situation was done in order to validate calculation finite element models used during strength analysis for project. The expertise contains: methodology of the measurements, description...
-
Factory Acceptance Test – Strain Gauge Measurement - Report no: WOiO /II/88/2014
PublicationTested object was 40 meters long jib and its foundation, placed in Gdansk Shiprepair Yard, manufactured by KMK. The contruction was dedicated to the passenger cruise vessel "North Star" The Strain Gauge measurement in different location and load situation was done in order to validate calculation finite element models used during strength analysis for project. The expertise contains: methodology of the measurements, description...
-
Identification of Optocoupler Devices with RTS Noise
PublicationThe results of noise measurements in low frequency range for CNY 17 type optocouplers are presented. The research were carried out on devices with different values of Current Transfer Ratio (CTR). The methods for identification of Random Telegraph Signal (RTS) in noise signal of optocouplers were proposed. It was found that the Noise Scattering Pattern method (NSP method) enables to identify RTS noise as non-Gaussian component...
-
Metrological analysis of an computerized system of protection against electric shock in circuits with variable speed drives
PublicationDrive systems, that can be operated at variable speed, are equipped with power electronics converters. This causes distortion of the earth current, and consequently the need to take into account the use of proper protective devices in relation to earth current harmonics. This paper presents a system for protection against electric shock in circuits with power electronics converters and metrological analysis indicating the requirements...
-
Evaluation of the fast impedance spectroscopy method in the laboratory measurement system
PublicationIn this paper the method for fast impedancespectroscopy of technical objects with very high impedance(|Zx| ≥ 1 GΩ) is evaluated by means of simulation and practicalexperiment. The method is based on excitation of an object, witha square pulse and measurements of voltage and currentresponses with DAQ card. The object impedance spectrum isobtained with use of continuous Fourier transform. Someimprovements of the method concerned...
-
TDOA Navigation Using CDMA2000 Signals – Experimental Results
PublicationThis paper presents results of an experiments on the possibility to estimate position of a CDMA2000 receiver on the basis of TDOA measurements. The hardware and software structure of a navigation receiver used during investigation is briefly described with focus on drawbacks and limitations. The main part of this paper contains basic information about CDMA2000 network in northern Poland, which signals were recorded during tests...
-
Determining the leakage current resistive component by the orthogonal vector method
PublicationThe measurement of the metal – oxide surge arresters (MOSA) leakage current and the analysis of its components is a key diagnostic criterion according to technical standards. During on site MOSA condition assessment, the easy way is based on the measurement only leakage current, without the inconvenient live working measurements of supply voltage. Orthogonal vectors method of determination the resistive leakage current is presented....
-
Liquid residence time in vortex separators
PublicationCentrifugal force enhances gravitational separation of suspension (vortex separators), as well as allows regulation of liquid discharge (vortex flow controls). Furthermore, it elongates the effective residence time of liquid inside the chamber in comparison to non-circulative flow. Laboratorz measurements, described in the paper, indicate that average liquid residence time for circulative flow exceeds 50% of plug-flow time,...
-
Distribution of roughness and waviness components of turned surface profiles
PublicationThe paper presents a spectral formulation of surface profile irregularity in a wideband frequency range for roughness, waviness and shape components along the measured length. A unique distribution of roughness and waviness components is proposed, according to the nature of their origination in the course of machining with tools of defined cutting edge, as distinct from standard filtration in measurements of surface irregularities....
-
Spatial Modelling in Environmental Analysis and Civil Engineering
PublicationAs can be seen, Spatial Modelling in Environmental Analysis and Civil Engineering applies to a multitude of applications. In an attempt to bring the topic closer to potential readers, the special issue referred to security methods, optimization of calculations, conducting measurements and empirical tests. Each article has made an original contribution to the development of practical science that can be replicated by researchers...
-
Application of mesh deformation for modeling of conformal RF components with 3D FEM
PublicationIn this paper, a method of analysis of conformal RF components has been proposed. In this approach, modeling of a curved structure is based on mesh deformation of planar objects rather than the construction of conformal geometry at CSG level. Since the model is represented as a 3D mesh, the deformation only requires the calculation of nodes position in the bent structure. The results of the proposed algorithm have been validated...
-
Wzrost zatrudnienia w pomorskich firmach – świadome planowanie czy przypadek
Publicationroblematyka poruszająca relację planowania w małych przedsiębiorstwach do wyników przez nie osiąganych doczekała się wielu badań, których wyniki są niejednoznaczne. Niejednoznaczność ta w dużym stopniu jest spowodowana wykorzystywaniem różnych miar tych zależności. Przeprowadzone na Pomorzu badania panelowe wskazały jednoznacznie na brak związków między planowaniem a wynikiem funkcjonowania przedsiębiorstwa mierzonego wzrostem...
-
Nośność konstrukcji gruntowo-łukowej prefabrykowanego wiaduktu w świetle obliczeń numerycznych i badań „in situ”
PublicationWartykule przedstawiono analizy przeprowadzone dla wiaduktu WK-15 Pomorskiej Kolei Metropolitalnej wykonanego w technologii łuków prefabrykowanych przykrytych gruntem (system TechSpan). W celu weryfikacji obliczeń numerycznych wykonano próbne obciążenie konstrukcji. Przedstawiono wyniki pomiarów naprężeń i prezmieszczeń konstrukcji. Odniesiono się krytycznie do zastosowanego modelu obliczeniowego.
-
Field-induced suppression of charge density wave in GdNiC2
PublicationWe report the specific heat, magnetic, magnetotransport, and galvanomagnetic properties of polycrystalline GdNiC 2 . In the intermediate temperature region above T N = 20 K, we observe large negative magnetoresistance due to Zeeman splitting of the electronic bands and partial destruction of a charge density wave ground state. Our magnetoresistance and Hall measurements show that at low temperatures a magnetic field-induced transformation from...
-
Influence of operation of national experimental nuclear reactor on the natural environment
PublicationThis paper presents the impact of experimental nuclear reactor operations on the national environment, based on assessment reports of the radiological protection of active nuclear technology sources. Using the analysis of measurements carried out in the last 15 years, the trends are presented in selected elements of the environment on the Świerk Nuclear Centre site and its surroundings. In addition, the impact of research results...
-
Effect of glycolysate obtained from polyurethane wastes on mechanical properties of rubber materials
PublicationThe paper presents the possibility of utilization of wastes from polyurethane foams. In this work the results of mechanical investigations of materials obtained from natural rubber mixtures with a mixture of glycolysate and biodiesel glycerine as a plasticizer are described. The measurements of mechanical properties showed rather good tensile strength, elongation at break and modules of extensions M100%, M200%, M300% of obtained...
-
Measurement of complex refractive index of human blood by low-coherence interferometry
PublicationIn this article, the usefulness of the optical technique for measurements of blood complex refractive index has been examined. Measurement of optical properties of human blood is difficult to perform because of its nonuniform nature. However, results of my investigation have shown the usefulness of low-coherencei nterferometry for measurement complex refractive index of human blood. Furthermore, mathematical analysis of spectrum...
-
System of wireless magnetic sensors for detection and identification of ferromagnetic vehicles
PublicationThe paper presents the results of deformation of the Earth's magnetic field by land vehicles. Basing on the analysis of the shape of the magnetic field deformation, it is possible to detect and identify a vehicle. In order to eliminate the interference of the Earth's magnetic field by the environment, the measurements were performed in a differential configuration. Under a development project a wireless system of magnetic sensors...
-
Assessment of protective properties of rubber lining in absorbers of flue gas desulphurization systems.
PublicationResults of research on degradation of rubber lining which is the main protection of absorbers in flue gas desulphurization (FGD) systems were presented. The power plant where the system operated is lignite-fired. Owing to measurements using electrochemical impedance spectroscopy and gravimetric determination of water content in the lining, the areas of the system which are most exposed to degradation were shown. The results obtained...
-
Synthesis and Testing of BCZY/LNZ Mixed Proton–electron Conducting Composites for Fuel Cell Applications
PublicationA composite of BaCe0.6Zr0.2Y0.2O3–δ and Li2O:NiO:ZnO was investigated for fuel cell applications. The composite was successfully synthesized and its phase stability was confirmed at temperatures up to 900 °C. The influence of sintering and pressing aids on density was also investigated. Electrical properties were measured. DC electrical conductivity was about 8•10-4 S/m at 845 K. Open circuit voltage measurements in wet hydrogen...
-
Materials for Mediator-free Electron Transfer in the Enzymatic Electrodes of Biobatteries and Biofuel Cells
PublicationWe present functionalization of single-walled carbon nanotubes (SWCNTs) and their application in the enzymatic fuel cells construction. SWCNTs were covalently modified with different types of aromatic moieties. Free radical reaction was employed to create direct carbon-carbon bond between moiety and SWCNTs. In second approach functionalization takes place through amide bonding. Functionalized SWCNTs were characterized by spectroscopy...
-
The Effect of Welding Conditions on Mechanical Properties of Superduplex Stainless Steel Welded Joints
PublicationThe tests results of superduplex stainless steel welded joints made with a different heat input, using automatic submerged arc welding (SAW) and semi-automatic flux-cored arc welding (FCAW) have been presented. Metallographic examinations, the measurements of the ferrite content, the width of the heat affected zone (HAZ) and the hardness of the welds in characteristic areas have been performed. Significant differences in the amount of...
-
An Analysis of Probe-Fed Rectangular Patch Antennas With Multilayer and Multipatch Configurations on Cylindrical Surfaces
PublicationA multi-patch configuration of probe-fed rectangular microstrip antennas mounted on a cylindrical body, with electrically small radius, with an arbitrary number of substrate and superstrate layers is investigated in this paper. A full-wave analysis and a moment-method calculation are employed. A unified procedure for creating proper matrices for the investigated geometry of the structure is outlined here. Numerical results for...
-
Measurement and Analysis of the Radio Wave Polarisation in Off-Body Communications in Indoor Environment
PublicationThe paper describes an analysis of the radio wave polarisation in off-body communications in indoor environment. The measurement stand for polarisation measurements has been shortly described. Five investigated scenarios with different body postures and different antenna placements have been characterize. The vertical and horizontal components of received radio signal have been analysed. The measure used in analysis is a ratio...
-
The Use of Liquid Crystal Thermography an Image Processing in Heat and Fluid-Flow Research
PublicationLiquid crystal thermography (LCT) have been used in many technical, industrial and biomedical applications [1]. During over 20 years it has been successfully applied in Department of Energy and Industrial Apparatus at Gdansk University of Technology for visualization of steady-state and transient temperature fields. In order to demonstrate feasibility of LCT techniques in practical heat transfer contexts, the authors have performed...
-
Optical method for verification of homogeneity of phantoms for calibration of magnetic resonance
PublicationThe primary purpose of this study was to develop a laboratory photonic set-up for characterisation of homogeneity of gel phantoms for calibration of magnetic resonance. In this system, optical coherence tomography allows the detection of micro- and macroscopic heterogeneities of a structure. The set-up was used to perform measurements of agar and agar-carrageenan gels, which are the basis for more complex phantoms for magnetic...
-
THE INFLUENCE OF MANUFACTURING OVERSIZING ON POSTWELDING DISTORTIONS OF THE FILLET WELDED JOINT
PublicationWelding proces is basic joining technique in shipbuilding. Such method generated welding distortions which cause a lot of problems during the manufacturing process. In the literature it is proposed wide spectrum of suggestions for a correct estimation of welding deformation in particular angular deformation in the fillet welded T joint. In the work influence of oversizing of weld on angular distortions of joint is presented basing...