Filters
total: 5706
filtered: 3995
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: plastic hinges
-
Estimation of the amplitude of the signal for the active optical gesture sensor with sparse detectors
PublicationIn this paper we deal with the problem of precise gesture recognition for the active optical proximity sensor with sparse 8 photodiodes. We particularly focus on developing the method of estimating the real, usually not observable, maximum signal value representing maximum intensity of light reflected from an obstacle present in the front of the sensor. Different configurations of the fingers were used as an obstacle. The Monte Carlo...
-
Reduced order model of 2d system
PublicationA new method of modelling is developed for static and dynamic analysis of two-dimensional elastic bodies. In the analysis, an elastic body is divided into strips. For each one-dimensional strip the reduced modal model is build up. The modal model contains appropriate number of inputs and outputs to connect lumped interaction that occur between strips. Proposed method of modelling enables to obtain more accurate and more simple...
-
Polyester sail technical woven fabric behaviour under uniaxial and biaxial tensile tests
PublicationThe paper is focused on the identification of mechanical properties of a sail technical woven fabric (yacht sailcloth polyester) style 480 AP with MTO (Medium Tempered Optimized) finish. The non-linear elastic behaviour of the fabric applied for sails is investigated under uniaxial and biaxial tensile tests. Comparison of non-linear elastic parameters with others polyester coated fabrics is made. This paper is intended to be an...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART II IDENTIFICATION STUDIES – DEVELOPING THE FATIGUE DURABILITY MODEL OF A DRIVE SHAFT
PublicationThe article presents a continuation of research carried out concerning identification of energy consequences of mechanical fatigue within a propeller shaft in a rotating mechanical system, while working under conditions of the loss of the required alignment of shaft lines. Experimental research was carried out on a physical model reflecting a full-sized real object: i.e., the propulsion system of the ship. It is proven, by means...
-
Poroelastic Low Noise Road Surfaces
PublicationNoise is one of the most important problems related to road traffic. During the last decades, noise emitted by engine and powertrain of vehicles was greatly reduced and tyres became a clearly dominant noise source. The paper describes the concept of low noise poroelastic road surfaces that are composed with mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and are much more flexible...
-
Ultra Low Noise Poroelastic Road Surfaces
PublicationNoise is one of the most important environmental problems related to road traffic. During the last decades, the noise emitted by the engines and powertrains of vehicles was greatly reduced and tires became a clearly dominant noise source. The article describes the concept of low noise poroelastic road surfaces that are composed of mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and...
-
Deregulacja polskiego rynku pracy
PublicationHistorycznie ukształtowana regulacja rynku pracy związana jest z jego infrastrukturą organizacyjno-prawną, tzn. przepisami dotyczącymi płac, czasu pracy i ochrony stosunku pracy. W opinii zwolenników deregulacji utrudnia ona elastyczne dostosowywanie się do rozmiarów zatrudnienia w zależności od zaistniałej sytuacji gospodarczej, powodując wzrost bezrobocia strukturalnego i wzrost kosztów pracy. Deregulacja rynku pracy związana...
-
New perspective on the in vivo use of cold stress dynamic thermography in integumental reconstruction with the use of skin-muscle flaps
PublicationAmong the problems encountered by plastic surgeons is the reconstruction of defects following tumors. One of the reconstructive options is TRAM flap. Despite that anatomy is well-explored, marginal flap necrosis may develop. To minimize complications imaging examinations was designed to determine the degree of flap perfusion. One of them is the thermographic examination.
-
The experimental and numerical investigation of fracture behaviour in PMMA notched specimens under biaxial loading conditions – Tension with torsion
PublicationThis paper presents the results of experimental fracture test of flat PMMA specimens under biaxial loading condition tension with torsion (proportional). The specimens were made in two thicknesses: 5 and 15 mm and were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. Thanks to the ARAMIS 3D 4 M non-contact vision system, measurement of the elongation and twist angle were recorded. During experimental...
-
Identification of leaf rust resistance genes Lr34 and Lr46 in common wheat (Triticum aestivum L. ssp. aestivum) lines of different origin using multiplex PCR
Publication -
Application of Oil-in-Water Nanoemulsion Carrying Size-Defined Gold Nanoparticles Synthesized by Non-thermal Plasma for the Human Breast Cancer Cell Lines Migration and Apoptosis
Publication -
Raman Spectra Measurements for Chemical Identifications - Aspect of Uncertainty Sources and Reduction of Their Effects
PublicationRaman spectrometers enable fast and non-contact identification of examined chemicals. These devices measure Raman spectra and compare with the spectra database to identify unknown and often illicit chemicals (e.g. drugs, explosives) usually without any sample preparation. Raman spectra measurements are a challenge due to noise and interferences present outside the laboratories (field applications). The design of a portable Raman...
-
Degradation of implantable materials – in vivo and in vitro research
PublicationThe article concerns the biological and electrochemical degradation of metallic implants in vivo and in vitro studies. The in vivo research dealt with degradation of plates used to join bones, as well as endoprostheses. The most common damages were: metalosis, breaking in the microstructure changes, breaking in area of holes, as well as plastic deformation throughout the length of an implant. The material used for the research...
-
Radiation Therapy–Related Changes in Serum Proteome and Lipidome Are Primarily Associated With a Type of Acute Toxicity: Comparison of Radiation-Induced Effects in Patients Treated Because of Head and Neck Cancer or Prostate Cancer
Publication -
Low-energy positron scattering from gas-phase benzene
PublicationIn this paper we are presenting calculations of the elastic cross section of positrons with gas-phase benzene for the energy range from 0.25 eV to 9.0 eV. The calculations are done with the molecular R-matrix method for positron-scattering from poly-atomic molecules using a scaling factor to scale the electron-positron interaction. The scaling factor influences the position of the poles of the R-matrix. We adjust the scaling factor...
-
On rotary inertia of microstuctured beams and variations thereof
PublicationWe discuss the classic rotary inertia notion and extend it for microstructured beams introducing new microinertia parameters as an additional dynamic response to microstructure changes. Slender structures made of beam- or platelet-lattice metamaterials may exhibit not only large translations and rotations but also general deformations of inner structure. Here we considered a few examples of beam-like structures and derive their...
-
Eco-Friendly Electromagnetic Interference Shielding Materials from Flexible Reduced Graphene Oxide Filled Polycaprolactone/Polyaniline Nanocomposites
PublicationHybrid nanocomposites have the unique ability of enhancing material properties due to the existing synergistic effect of the fillers. In this study, the authors report such an eco-friendly hybrid nanocomposite comprising of polyaniline and reduced graphene oxide in polycaprolactone. The conducting polyaniline improved the processability of polycaprolactone, and the final composites were prepared by incorporating graphene oxide...
-
Mechanical properties of Precontraint 1202 S2 based on uniaxial tensile and creep tests
PublicationThe purpose of the paper is the estimation of the polyvinyl chloride – polyester-coated fabric (Precontraint 1202 S2) mechanical properties under uniaxial tensile tests as well as short- and long-time creep tests. The uniaxial tests are the basis of non-linear elastic description while the creep tests are used for the evaluation of the stiffness parameters in time and for the identification of the standard viscoelastic model. The...
-
Mechanical testing of technical woven fabrics
PublicationThis article presents a review of technical fabrics testing methods used by the authors on the basis of their experience with research on properties of polytetrefluoroethylene-coated fabrics used for Forest Opera in Sopot (Poland). First, the different types of testing methods used for description of mechanical properties (uniaxial tensile tests, biaxial tensile tests and shear tests) of technical woven fabrics are described. The...
-
Polyurethane/ground tire rubber composite foams based on polyglycerol: processing, mechanical and thermal properties
PublicationDuring the synthesis of rigid polyurethane foams, petrochemical polyol was substituted with polyglycerol, the product of thermo-catalytic polycondensation of waste glycerol, resulting from biodiesel production. Two types of ground tire rubbers, untreated and thermo-mechanically reclaimed, were used to obtain ‘‘green’’ polyurethane-polyglycerol composite foams. Samples were prepared by a single-step method for the ratio of NCO/OH...
-
Influence of selected submicron inorganic particles on mechanical and thermo-mechanical properties of unsaturated polyester/glass composites
PublicationIn this paper, the influence of different submicron-scaled particles (zinc oxide, titanium dioxide, or silica) on mechanical and thermo-mechanical properties of unsaturated polyester matrix composites reinforced with glass fabric was investigated. Surface morphology of obtained composites was also examined. At first inorganic particles were mechanically dispersed into unsaturated polyester resin system as per the calculated weight...
-
Influence of thermal effects on mechanical properties of PVDF-coated fabric
PublicationThis paper describes the method of laboratory tests necessary for identification of temperature influence on mechanical properties of polyvinylidene fluoride-coated polyester fabric often used for tensile structures. Two nonlinear model descriptions are investigated. The first one is based on the piece-wise linear relations between stress and strain and the second one on the Murnaghan model of solid behavior. This paper is proposed...
-
Mechanical properties of polyvinyl chloride-coated fabric under cyclic tests
PublicationThe aim of the present paper is to propose a method of laboratory tests necessary for the identification of mechanical properties of the coated fabric. The material parameters of the coated fabric AF 9032 are specified on the basis of the uniaxial and biaxial tensile tests. For the identification process, the techniques based on the least squares methods are used. Additionally, the uniaxial and biaxial cyclic tests are performed...
-
The Influence of Binding Agents on Stiffness of Mineral-cement-emulsion Mixtures
PublicationThis paper attempts to determine the behavior of mineral-cement-emulsion mixture (MCE) under load, whether is it similar to asphalt mixtures (viscoelastic behavior) or to cement treated materials (elastic behavior). To answer this question nine mineral- cement-emulsion mixtures with different combinations of cement and emulsion content were tested in laboratory using Simple Performance Test (SPT). For each mixture stiffness moduli...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublicationMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Separation of the effects of notch and macro residual stress on the MFL signal characteristics
PublicationMagnetic flux leakage (MFL) distribution for three configurations of samples has been investigated in order to study the influence of notch and plastic deformation separately as well as together. Samples have been made of S355 steel. The MFL signal measurements were carried out along the longest dimension of the sample over a length of 120 mm. Two components of magnetic field were measured: 1) tangential to the main axis and 2)...
-
Numerical Modelling of Connections Between Stones in Foundations of Historical Buildings
PublicationThe aim of this paper is to analyse the behaviour of old building foundations composed of stones (the main load-bearing elements) and mortar, based on numerical analysis. Some basic aspects of historical foundations are briefly discussed, with an emphasis on their development, techniques, and material. The behaviour of a foundation subjected to the loads transmitted from the upper parts of the structure is described...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Wykorzystanie kamery termowizyjnej nowej generacji do oceny wpływu sił ortodontycznych na dziąsło = The application of a new-generation thermal imaging camera for the assessment of hemodynamic changes in gingiva during orthodontic treatment
PublicationIntroduction. One ot the most interesting modern methods of assessing microcirculation is thermovisiual examination. Thermovision cameras are commonly used in general medicine. As the periodontium is one of the most vascularized tissues in the human body, the application of high-sensitivity thermovision cameras may allow tor noninvasive asses- sment and early detection ot pathological changes in the gingiva by giving a complete...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublicationTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublicationThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
Sounding of Layered Marine Bottom - Model Investigations
PublicationThe necessary actions connected with interpretations of examining of physical properties of sea bottom structure is developing of proper procedure of modeling of the layered structure. The implementation of the acoustic waves for the determination of seabed stratification requires a precise diagnosis of the topic from both the theoretical and practical side. Little differences between the parameters of sediments, as well as irregular...
-
Applications of Tensor Analysis in Continuum Mechanics
PublicationA tensor field is a tensor-valued function of position in space. The use of tensor fields allows us to present physical laws in a clear, compact form. A byproduct is a set of simple and clear rules for the representation of vector differential operators such as gradient, divergence, and Laplacian in curvilinear coordinate systems. The tensorial nature of a quantity permits us to formulate transformation rules for its components...
-
Electron Scattering from Methyl Formate (HCOOCH3): A Joint Theoretical and Experimental Study
PublicationElastic low-energy electron collisions with methyl formate have been studied theoretically at the level of various theories. The elastic integral cross section was calculated using Schwinger multichannel and R-matrix methods, in the static-exchange and static-exchange plus polarization levels of approximations for energies up to 15 eV. The absolute total cross section for electron scattering from methyl formate has been measured...
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublicationIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Numerical analyses of novel prefabricated structural wall panels in residential buildings based on laboratory tests in scale 1:1
PublicationThe paper presents experimental and numerical investigations on novel prefabricated composite building wall panels for residential building constructions. The wall panels were composed of reinforced concrete ribbed elements with the core from the EPS foam as the thermal insulation. The wall panels in the full-scale 1:1 were subjected to vertical loads. In the first step, the experiments were analysed with simple usual static methods....
-
Artificial Thermal Ageing of Polyester Reinforced and Polyvinyl Chloride Coated Technical Fabric
PublicationArchitectural fabric AF9032 has been subjected to artificial thermal ageing to determine changes of the material parameters of the fabric. The proposed method is based on the accelerated ageing approach proposed by Arrhenius. 300 mm x 50 mm samples were cut in the warp and fill directions and placed in a thermal chamber at 80 °C for up to 12 weeks or at 90 °C for up to 6 weeks. Then after one week of conditioning at ambient temperature,...
-
CROSS SECTIONS CALCULATIONS FOR ELECTRON SCATTERING FROM RHODANINE AND CYANOACETIC ACID
PublicationCross sections for electron-impact ionization and for elastic electron scattering for rhodanine (C3H3NOS2) and cyanoacetic acid (C3H3NO2) have been calculated in wide impinging electron energy range.
-
The reasons of considarable deflections of roof trusses in engineering analysis
PublicationThe aim of the paper is to present an unconventional analysis of deformations of roof trusses of an exhibition pavilion. Structure of the main hall of the pavilion consists of repeatable span frames with steel pillars made of I-sections, fastened in the foundations and hinged supporting roof girders. The roof trusses, completed in steel construction, have undergone considerable permanent deflections. Deformations of the lower chord...
-
A Nonlinear Model of a Mesh Shell
PublicationFor a certain class of elastic lattice shells experiencing finite deformations, a continual model using the equations of the so-called six-parameter shell theory has been proposed. Within this model, the kinematics of the shell is described using six kinematically independent scalar degrees of freedom — the field of displacements and turns, as in the case of the Cosserat continuum, which gives reason to call the model under consideration...
-
Pronounced cytostatic activity and bystander effect of a novel series of fluorescent tricyclic acyclovir and ganciclovir derivatives in herpes simplex virus thymidine kinase gene-transduced tumor cell lines
Publication -
Intensity Ratio of Kβ/Kα in Selected Elements from Mg to Cu, and the Chemical Effects of Cr Kα1,2 Diagram Lines and Cr Kβ/Kα Intensity Ratio in Cr Compounds
Publication -
The activity of latent benzoperimidine esters to inhibit P-glycoprotein and multidrug resistance-associated protein 1 dependent efflux of pirarubicin from several lines of multidrug resistant tumor cells.
PublicationZaprezentowano wyniki badań biologicznych przeprowadzonych dla nowej grupy związków: estrów benzoperymidyny z zastosowaniem wybranych linii komórek nowotworowych: wrażliwych i opornych o oporności P-gp-zależnej, MRP1-zależnej i o oporności związanej z nadekspresją białek MRP1/LRP. Metodą spektrofluorymetryczną zbadano zdolność estrów benzoperymidyny do hamowania eksportu aktywnego pirarubicyny z komórek opornych. Estry benzoperymidyny...
-
2,7-Dihydro-3H-pyridazino[5,4,3-kl]acridin-3-one derivatives, novel type of cytotoxic agents active on multidrug-resistant cell lines. Synthesis and biological evaluation.
PublicationOtrzymano serię pirydazyno akrydyn-3-onów w reakcji 9-okso-9,10-dihydroakrydyno-1-karboksylanu etylu z POCl3, następnie dodanie odpowiedniej alkiloaminoalkilohydrazyny. Badane związki wykazują w porównaniu z referencyjnymi cytostatykami DX, MIT niższe wartości indeksu RI, a także niższe aktywności cytotoksyczne.
-
A multi-analytical approach to the characterization of natural organic dyestuffs and inorganic substrates present in the 19th-century artistic oil paints manufactured by a French art materials supplier Richard Aines
PublicationThis paper presents a comprehensive analysis of artistic paints produced in the 19th century by a French art materials supplier Richard Ain`es. Improved mild extraction with hydrofluoric acid enabled the observation of intact organic dyes. Reversed-phase liquid chromatography with diode-array and mass spectrometry detection was utilised for the identification of 35 dyes present in yellow and red paint samples, and in selected plant...
-
Elektryczne zespoły zasobnikowe jako alternatywa dla elektryfikacji nowych linii w Trójmieście = Electric Multiple Units With Energy Storage – Alternative to Electrification of New Lines in Three City
PublicationRozważono zastosowanie nowoczesnych zespołów trakcyjnych na liniach pasażerskich Trójmiasta. Zaproponowano budowę linii Gdańsk Śródmieście - Orunia Górna oraz odtworzenie komunikacji do północnych dzielnic Gdyni. Przeanalizowano trójmiejski układ komunikacyjny dla ruchu pociągów z zasobnikami energii. Zaproponowano trasę Orunia Górna - Wrzeszcz - Osowa - Chylonia - Port Oksywie z naprzemiennie występującymi odcinkami zelektryfikowanymi...
-
Tackling microplastics pollution in global environment through integration of applied technology, policy instruments, and legislation
PublicationMicroplastic pollution is a serious environmental problem that affects both aquatic and terrestrial ecosystems. Small particles with size of less than 5 mm, known as microplastics (MPs), persist in the environment and pose serious threats to various species from micro-organisms to humans. However, terrestrial environment has received less attention than the aquatic environment, despite being a major source of MPs that eventually...
-
Intelligent monitoring the vertical dynamics of wheeled inspection vehicles
PublicationThe problem of intelligent monitoring of the vertical dynamics of wheeled inspection vehicles is addressed. With the independent MacPherson suspension system installed, the basic analysis focuses on the evaluation of the parameters of the so-called quarter car model. To identify a physically motivated continuous description, in practice, dedicated integral-horizontal filters are used. The obtained discrete model, which retains...
-
Investigation of the 0.4C-35Cr-45Ni-Nb Alloy after Service in High-Temperature Steam and Hydrocarbons Environment
PublicationThe paper presents the results of investigation of the 0.4C-35Cr-45Ni-Nb alloy, which operated in the cracked hydrocarbon feeds and dilution steam at 1125 C. The material originated from the pyrolytic furnace coil tubes, of which internal walls were in contact with the aforementioned medium, whereas the external walls were in contact with the flue gases. The examination included metallographic and mechanical tests on the material...
-
Inkjet Printing of Lanthanide–Organic Frameworks for Anti-Counterfeiting Applications
PublicationPhotoluminescent lanthanide−organic frameworks (Ln-MOFs) were printed onto plastic and paper foils with a conventional inkjet printer. Ln-MOF inks were used to reproduce color images that can only be observed under UV light irradiation. This approach opens a new window for exploring Ln-MOF materials in technological applications, such as optical devices (e.g., lab-on-a-chip), as proof of authenticity for official documents.