Filters
total: 373
filtered: 291
Search results for: PENTACENE BLEND
-
Complementary Use of Multi-dimensional Gas Chromatography and Proton Transfer Reaction Mass Spectrometry for Identification of Rapeseed Oil Quality Indicators
PublicationThe change of concentration of various volatiles generated during frying may be an indicator of oil quality. Chemical compounds such as aldehydes, ketones, alcohols and carboxyl acids are the products of oxidation during thermal degradation of edible oils. Shown in this work is a complementary use of GC×GC-TOFMS and PTR-MS for the detection and determination of quality indicators of rapeseed oil. The former technique was used for...
-
Microwave-assisted preparation of potato starch silicated with silicic acid
PublicationApplication of microwave irradiation for the silication of granular potato starch with silicic acid, and the properties of silicated starch were investigated. Potato starch was esterified on 20 min microwave irradiation of starch with silicic acid, applying the power of 450 or 800Wand, for comparison, on 120 min convectional heating of the reagent blend at 100 ◦C. The degree of esterification and the reaction efficiency did not...
-
Negative carbon dioxide gas power plant integrated with gasification of sewage sludge
PublicationOne of the primary objectives of the negative carbon dioxide gas power plant (nCO2PP) is to develop an innovative technology confirming the possibility of the use of sewage sludge to produce electricity while having a positive impact on the environment. In this paper, a mathematical model is presented to estimate thermodynamic parameters of the system in relation to the gasification process and changes in such parameters in the...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublicationThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
Current trends in the field of steganalysis and guidelines for constructions of new steganalysis schemes
PublicationThe paper concerns blind steganalysis techniques in the passive steganalysis scenario designed to detect the steganographic cover modification schemes. The goal is to investigate the state-of-art in the field of steganalysis, and, above all, to recognize current trends existing in this field and determine guidelines for constructions of new steganalysis schemes. The intended effects are to examine the possibilities for the development...
-
Modelowanie i ograniczanie skutków ataków uzurpacji uprawnień w systemach teleinformatycznych wspierających różnicowanie poziomu QoS
PublicationW wieloagentowych systemach teleinformatycznych pracujących w paradygmacie Klient-Serwer i wspierających różnicowanie poziomu QoS poważnym zagrożeniem są ataki uzurpacji uprawnień metodą Fałszywego VIPa. Ich celem jest zapewnienie Klientowi nienależnie wysokiego poziomu QoS, co powoduje nadużycie zasobów Serwera i szkody dla innych Klientów. W referacie podjęto próbę sforma-lizowania modelu takich ataków oraz zaproponowa-no obustronnie...
-
Determination of API content in a pilot-scale blending by near-infrared spectroscopy as a first step method to process line implementation
PublicationNear infrared (NIR) spectroscopy was used for estimation of powder blend homogeneity and manufacturing control of a medicinal product powder mixture containing active pharmaceutical ingredient (API). Aiming at initiating a Process Analytical Technology (PAT) activity, the first step was a stationary mode atline evaluation. In this, the content of pharmaceutical active compound in the powder mixtures intended to the direct tabletting...
-
Quantitative assessment of the main antioxidant compounds, antioxidant activities and FTIR spectra from commonly consumed fruits, compared to standard kiwi fruit
PublicationBioactive compounds (polyphenols and ascorbic acid) and dietary fibers, and related antioxidant activities of commonly consumed apples, bananas, peaches, pears, blond and red grapefruits, pomelos, oranges, lemons, red plums, white grapes, mango, persimmon and strawberries grown in the same geographical and climatic conditions were compared with standard kiwi fruit. The presence of polyphenols was studied by Fourier transform infrared...
-
Wideband crossover structure with double ring resonators
PublicationThe structure of a four-port microstrip crossover is presented. The device is composed of two ring resonators, one circular and one built from meander lines, connected by four straight lines. The equivalent circuit model of the crossover is derived. The structure is designed on thin and flexible substrate to allow it to bend. The possibility of applying the device on curved surfaces is tested experimentally.
-
Thermal degradation assessment of canola and olive oil using ultra-fast gas chromatography coupled with chemometrics
PublicationOil blending is often used to enhance the properties of vegetable oils. The admixture of a more thermally stable oil makes the resulting blend more suitable for use in frying. A new method of quality assessment of vegetable oils used in frying is presented in this paper. In this method, ultra-fast gas chromatography coupled with flame ionization detector and chemometrics is employed. Principal component analysis was used for data...
-
Hybrid cross-linked chitosan/protonated-proline:glucose DES membranes with superior pervaporation performance for ethanol dehydration
PublicationThis work explores a protonated L-proline:glucose (molar ratio 5:1) deep eutectic solvent (DES) in fabricating biopolymer membranes utilizing chitosan (CS). Initially, the miscibility of CS and DES to prepare homogeneous dense blend membranes has been investigated. Different techniques, such as scanning electron microscopy, contact angle (CA), atomic force microscopy (AFM), Fourier transformed infrared spectroscopy (FTIR) and swelling...
-
Fabrication of toughened plastic using styrene butadiene rubber-poly (methyl methacrylate) interpenetrating polymer networks
PublicationA standard set of interpenetrating polymeric networks (IPNs) has been contrived using an elastomerstyrene butadiene rubber and a thermoplastic poly (methyl methacrylate) through sequential polymerization protocol. This low-cost material can be hopefully engaged as a toughened plastic with cocontinuous morphology. Different morphological protocols including Raman imaging are effectively utilized to envisage the effect of blend ratio...
-
Application of microturbines in CHP systems with reciprocating engines
PublicationThe analysis was carried out for Combined Heat and Power generation systems with micro-turbines power plants working on heat rejected from the reciprocating engine. The calculations were performed for GE Jerbacher engines of J320 GS- C05, J320 GS- C25 and J416 GS- B05 types. We considered different working media (both wet and dry fluids): water, ammonia, ethanol, methanol, methylacetylene (propyne), dimethyloether, sulphur dioxide,...
-
Updating Finite Element Model of a Wind Turbine Blade Section Using Experimental Modal Analysis Results
PublicationThis paper presents selected results and aspects of themultidisciplinary and interdisciplinary research oriented for the experimental and numerical study of the structural dynamics of a bend-twist coupled full scale section of awind turbine blade structure.Themain goal of the conducted research is to validate finite elementmodel of themodified wind turbine blade section mounted in the flexible support structure accordingly to the...
-
Feature extraction in detection and recognition of graphical objects
PublicationDetection and recognition of graphic objects in images are of great and growing importance in many areas, such as medical and industrial diagnostics, control systems in automation and robotics, or various types of security systems, including biometric security systems related to the recognition of the face or iris of the eye. In addition, there are all systems that facilitate the personal life of the blind people, visually impaired...
-
Interactions of fish gelatin and chitosan in uncrosslinked and crosslinked with EDC films: FT-IR study
PublicationFilms based on fish gelatin, chitosan and blend of fish gelatin and chitosan before and after cross-linking with EDC have been characterized by FT-IR spectroscopy. The FT-IR spectrum of fish gelatin film showed the characteristic amide I, amide II and amide III bands, and the FT-IR spectrum of chitosan film confirmed that the polymer was only a partially deacetylated product, and included CH3-C=O and NH2 groups, the latter both...
-
Syntheses and structures of the first terminal phosphanylphosphido complex of hafnium [cp2hf(cl){η1-(me3si)p-p(net2)2}] and the firstzirconocene-phosphanylphosphinidene dimer [cp2zr{μ2-p-p(net2)2}2zrcp2]
PublicationReactions of (Et2N)2P-P(SiMe3)Li with [Cp2MCl2] (M= Zr, Hf) in toluene or pentane yield the related terminal phosphanylphosphido complexes [Cp2M(Cl){η1-(Me3Si)P-P(NEt2)2}]. The solid statestructure of [Cp2Hf(Cl){η1-(Me3Si)P-P(NEt2)2}] was established by single crystal X-ray diffraction. The reaction of (Et2N)2P-P(SiMe3)Li with [Cp2ZrCl2] in THF or DME solutions leads to the formationof deep red crystals of the first neutral diamagnetic...
-
Knowledge-Based Virtual Modeling and Simulation of Manufacturing Processes for Industry 4.0
PublicationABSTRACT Industry 4.0 aims at providing a digital representation of a production landscape, but the challenges in building, maintaining, optimizing, and evolving digital models in inter-organizational production chains have not been identified yet in a systematic manner. In this paper, various Industry 4.0 research and technical challenges are addressed, and their present scenario is discussed. Moreover, in this article, the novel...
-
Preparation and characterization of genipin cross-linked porous chitosan–collagen–gelatin scaffolds using chitosan–CO2 solution
PublicationNovel porous scaffolds composed of chitosan, collagen and gelatin were prepared by the multistep procedure involving final freeze-drying and characterized. To eliminate the need for residual acid removal from the material after drying, carbon dioxide saturation process was used for chitosan blend formulation. The use of CO2 for chitosan dissolution made the scaffold preparation process more reproducible and economically sustainable....
-
HIGH TEMPERATURE HEAT PUMPS – PERSPECTIVE HEATING SYSTEMS?
PublicationIn the paper presented are authors own concepts of high temperature compressor heat pumps for the utilisation of medium and low temperature sources of heat. Working fluids for use in high temperature heat pumps are discussed, as well as the criteria for their selection. Analyses are presented for the production of in the upper steam source at 130 °C. One-stage systems and cascade systems were analyzed. An analysis of the coefficient...
-
Synthesis and properties of carboxy derivative of Epidian 6 monomethacrylate (in English)
PublicationWe present the synthesis of an oligomer with carboxy and methacrylic groups based on Epidian 6. The effect of the catalyst nature and amount, solvent nature and process temperature on the rate of the reaction between Epidian6 monomethacrylate and adipic acid was examined at 313, 323 and 333 K in the presence of 4-dimethylaminopyridine, 1,4-diazobicyclo[2.2.2]octane, and benzyltriammonium chloride. The synthesized oligomer was characterized...
-
Application of cyanated asphaltenes in gas-phase adsorption processes for removal of volatile organic compounds
PublicationThe paper presents an innovative, chemically modified (methylcyanated) asphaltene-based adsorbent that can be an inter-esting low-cost alternative for traditional adsorbents. Adsorption properties of adsorbents were examined by inverse gas chromatography technique, adsorption isotherms, and breakthrough curves. A significant increase in retention volume for pyridine, 2-pentanone, nitropropane, toluene, and 1-butanol was observed....
-
Composite Materials Based on Silicon Oxycarbide as Anodes for Lithium-Ion Batteries
PublicationIn this work, the properties of binary SiOC/graphite and SiOC/tin, as well as ternary SiOC/graphite/tin obtained from various preceramic precursors are described. During the first step, the materials were synthesized using various techniques such as sol-gel and hydrosilylation. To prevent sedimentation and agglomeration of graphite particles during the gelation stage without using surfactants and thickeners, a new gelation technique...
-
Influence of microwave treatment conditions of GTR on physico-mechanical and structural properties of NBR/NR/GTR composites
PublicationThe increasing amount of tires used in the industry induces the researchers to find alternatives to the recycling of the end-of-life tires. Several alternatives in order to application of ground tire rubber GTR include their incorporation as a filler in composites. The main issue in this approach is the lack of compatibility between GTR and polymer matrix. In order to solve this problem the devulcanization by microwaves has been...
-
Dynamic mechanical properties and flexing fatigue resistance of tire sidewall rubber as function of waste tire rubber reclaiming degree
PublicationA stepwise downsizing method of gel particles in reclaimed rubber to a micro-nano scale and its excellent dynamic performance in tire sidewall were introduced by this work. The results showed that the size of gel particles decreased from several micrometers to micro-nanometers with the increase of reclaiming degree, accompanied by reduced molecular weight and widened molecular weight distribution of sol fraction. The addition of...
-
Recent Advances in Development of Waste-Based Polymer Materials: A Review
PublicationLimited petroleum sources, suitable law regulations, and higher awareness within society has caused sustainable development of manufacturing and recycling of polymer blends and composites to be gaining increasing attention. This work aims to report recent advances in the manufacturing of environmentally friendly and low-cost polymer materials based on post-production and postconsumer wastes. Sustainable development of three groups...
-
Testing Watermark Robustness against Application of Audio Restoration Algorithms
PublicationThe purpose of this study was to test to what extent watermarks embedded in distorted audio signals are immune to audio restoration algorithm performing. Several restoration routines such as noise reduction, spectrum expansion, clipping or clicks reduction were applied in the online website system. The online service was extended with some copyright protection mechanisms proposed by the authors. They contain low-level music features...
-
Medical Image Dataset Annotation Service (MIDAS)
PublicationMIDAS (Medical Image Dataset Annotation Service) is a custom-tailored tool for creating and managing datasets either for deep learning, as well as machine learning or any form of statistical research. The aim of the project is to provide one-fit-all platform for creating medical image datasets that could easily blend in hospital's workflow. In our work, we focus on the importance of medical data anonimization, discussing the...
-
Aktywności stymulujące refleksję w nauczaniu języka pisanego w wirtualnej klasie
PublicationThe paper aims to show how to engage students attending an online language course in various activities which by stimulating reflection enhance the learning process and result in better learning outcomes. By blending cognitivist, constructivist, constructionist and behavioural ideas, course developers and tutors can produce materials and use methods which satisfy the varied needs of adults who want to improve their writing skills....
-
DETERMINATION OF SP3 FRACTION IN ta-C COATING USING XPS AND RAMAN SPECTROSCOPY
PublicationThe paper presents results of studies on the structure of tetrahedral amorphous carbon films (ta-C) with a thickness in the range from 20 to 280 nm, deposited using pulsed vacuum arc technique with an electromagnetic Venetian blind plasma filter. The results of the phase structure analysis, obtained using visible Raman spectroscopy and UV Raman spectroscopy methods, showed a strong dependence of the results on the presence, on...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublicationThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
Low-Level Music Feature Vectors Embedded as Watermarks
PublicationIn this paper a method consisting in embedding low-level music feature vectors as watermarks into a musical signal is proposed. First, a review of some recent watermarking techniques and the main goals of development of digital watermarking research are provided. Then, a short overview of parameterization employed in the area of Music Information Retrieval is given. A methodology of non-blind watermarking applied to music-content...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements Dataset
PublicationThe dataset titled EH36 steel for shipbuilding (plate thickness 50 mm) – CMOD – force record, a0/W=0.6 contains a CMOD (Crack Mouth Opening Displacement) – Force record which is the base for evaluation of the fracture toughness of structural steel. Bend specimens with a Bx2B section (B = 50 mm), and relative initial crack length a0/W=0.60 were used. The test was carried out at ambient temperature in accordance with the ISO 12135...
-
Preliminary Testing of the Influence of Modified Polycaprolactones on Anabaena Variabilis Growth in Seawater
PublicationSeveral new biodegradable polymer materials have recently come onto the global market. Mostly the results on degradation kinetic studies are presented. This paper suggests using one of the tests to estimate the impact of polymer packaging material on sea life. The microorganism chosen was Anabaena variabilis (identified in many waters, including those of the Baltic Sea, especially in the Gulf of Gdansk and Puck Bay; this cyanobacterium...
-
Thermosensitive composite based on agarose and chitosan saturated with carbon dioxide. Preliminary study of requirements for production of new CSAG bioink.
PublicationThis study introduces a method for producing printable, thermosensitive bioink formulated from agarose (AG) and carbon dioxide-saturated chitosan (CS) hydrogels. The research identified medium molecular weight chitosan as optimal for bioink production, with a preferred chitosan hydrogel content of 40–60 %. Rheological analysis reveals the bioink's pseudoplastic behavior and a sol-gel phase transition between 27.0 and 31.5 °C. The...
-
Silicon Oxycarbide-Graphite Electrodes for High-Power Energy Storage Devices
PublicationHerein we present a study on polymer-derived silicon oxycarbide (SiOC)/graphite composites for a potential application as an electrode in high power energy storage devices, such as Lithium-Ion Capacitor (LIC). The composites were processed using high power ultrasound-assisted sol-gel synthesis followed by pyrolysis. The intensive sonication enhances gelation and drying process, improving the homogenous distribution of the graphitic...
-
Analyzing the Effectiveness of the Brain–Computer Interface for Task Discerning Based on Machine Learning
PublicationThe aim of the study is to compare electroencephalographic (EEG) signal feature extraction methods in the context of the effectiveness of the classification of brain activities. For classification, electroencephalographic signals were obtained using an EEG device from 17 subjects in three mental states (relaxation, excitation, and solving logical task). Blind source separation employing independent component analysis (ICA) was...
-
In uence of Low-Level Features Extracted from Rhythmic and Harmonic Sections on Music Genre Classi cation
PublicationWe present a comprehensive evaluation of the infuence of 'harmonic' and rhythmic sections contained in an audio file on automatic music genre classi cation. The study is performed using the ISMIS database composed of music files, which are represented by vectors of acoustic parameters describing low-level music features. Non-negative Matrix Factorization serves for blind separation of instrument components. Rhythmic components...
-
Hospital as a landscape mark
PublicationHalf of the nineteenth century brought significant changes in the organization and operation of hospitals. The on-coming takeover by the state and its agencies tasks related to medical care resulted in a significant jump in quantitative and almost massive construction of new hospitals. Several hospitals and nursing homes functioned on a relatively small area of a city or town, with different specializations and profiles of care....
-
Soft Tissue Retraction Maneuver in Cone Beam Computed Tomography Prior to Crown-Lengthening Procedure—A Technical Note
PublicationBackground: An accurate determination of the biological width and the relationship of the cemento-enamel junction with the border of the alveolar bone is crucial during a clinical crown-lengthening (CCL) procedure. The aim of this study was to present a technical note about the retraction techniques in cone beam computed tomography (CBCT) prior to CCL, highlighting the significant enhancement in procedural accuracy and predictability...
-
Data-Driven Modeling of Mechanical Properties of Fiber-Reinforced Concrete: A Critical Review
PublicationFiber-reinforced concrete (FRC) is extensively used in diverse structural engineering applications, and its mechanical properties are crucial for designing and evaluating its performance. The compressive, flexural, splitting tensile, and shear strengths of FRCs are among the most important attributes, which have been discussed more extensively than other properties. The accurate prediction of these properties, which are required...
-
Intermolecular Interactions as a Measure of Dapsone Solubility in Neat Solvents and Binary Solvent Mixtures
PublicationDapsone is an effective antibacterial drug used to treat a variety of conditions. However, the aqueous solubility of this drug is limited, as is its permeability. This study expands the available solubility data pool for dapsone by measuring its solubility in several pure organic solvents: N-methyl-2-pyrrolidone (CAS: 872-50-4), dimethyl sulfoxide (CAS: 67-68-5), 4-formylmorpholine (CAS: 4394-85-8), tetraethylene pentamine (CAS:...
-
The analytical design method of railway route’s main directions intersection area
PublicationThe paper presents a design method related to railway track sections situated in a bend. In the method advantage is taken of an analytical form of description by using appropriate mathematical formulae. This may becomeparticularly usefulwhen the investigations are based on the data obtained from mobile satellite measurements. In the paper attention is concentrated on an universal approach creating an opportunity to diversify the...
-
Organic Rankine as bottoming cycle to a combined Brayton and Clausius-Rankine cycle
PublicationThis paper presents an enhanced approach, as it will be considered here that the ORC installation could be extra-heated with the bleed steam, a concept presented by the authors. In such way the efficiency of the bottoming cycle can be increased and an amount of electricity generated increases. A thermodynamic analysis and a comparative study of the cycle efficiency for a simplified steam cycle cooperating with ORC cycle will be...
-
The electrochemical impedance spectroscopy studies of the anode material based on polymer and starch derived ceramic for lithium ion batteries
PublicationThe anode materials derived of preceramic polymer poly(1,2-dimethylsilazane) (PSN) and starch was study. Commercially available polysilazane (poly(1,2-dimethylsilazane (PSN 2M01 Gelest) was mixed with commercially available starch (POCH Gliwice). The ratio polymer/starch (PSN/starch) was 1/1 or 3/7. The polysialazane/starch blend was cross-linked at 230 ºC for 2 h followed by heating to the final temperature (500 ºC, 700 ºC and...
-
Collagen Type II—Chitosan Interactions as Dependent on Hydroxylation and Acetylation Inferred from Molecular Dynamics Simulations
PublicationChitosan–collagen blends have been widely applied in tissue engineering, joints diseases treatment, and many other biomedical fields. Understanding the affinity between chitosan and collagen type II is particularly relevant in the context of mechanical properties modulation, which is closely associated with designing biomaterials suitable for cartilage and synovial fluid regeneration. However, many structural features influence...
-
An investigation on the role of GMA grafting degree on the efficiency of PET/PP-g-GMA reactive blending: morphology and mechanical properties
PublicationGlycidyl methacrylate (GMA) has been grafted on polypropylene (PP) with the aid of styrene (St) comonomer, by changing dicumyl peroxide initiator content, GMA level, and St concentration. The performance of the resulting PP-g-GMA reactive material towards static and dynamic mechanical properties of poly (ethylene terephthalate) (PET) was monitored in terms of grafting reaction variables and compatibilizer content. Fourier transform...
-
Practical I-Voting on Stellar Blockchain
PublicationIn this paper, we propose a privacy-preserving i-voting system based on the public Stellar Blockchain network. We argue that the proposed system satisfies all requirements stated for a robust i-voting system including transparency, verifiability, and voter anonymity. The practical architecture of the system abstracts a voter from blockchain technology used underneath. To keep user privacy, we propose a privacy-first protocol that...
-
Digital fingerprinting for color images based on the quaternion encryption scheme
PublicationIn this paper we present a new quaternion-based encryption technique for color images. In the proposed encryption method, images are written as quaternions and are rotated in a three-dimensional space around another quaternion, which is an encryption key. The encryption process uses the cipher block chaining (CBC) mode. Further, this paper shows that our encryption algorithm enables digital fingerprinting as an additional feature....
-
In vitro antioxidative and binding properties of phenolics in traditional, citrus and exotic fruits
PublicationMany polyphenols bind proteins, therefore our research was focused on the potential of protein binding to polyphenols of investigated fruits and their health-related effects. The contents of polyphenols and related antioxidant activities of traditional, citrus and exotic fruits were compared. The presence of polyphenols (flavonoids and phenolic acids) in the investigated samples and their interaction with human serum albumin (HSA)...