displaying 1000 best results Help
Search results for: IMPEDANCE CONVERTORS
-
APPLICATION OF THE HIGH FREQUENCY LINEARIZATION OF THE EAR IN PATIENTS WITH TINNITUS . Metoda linearyzacji narządu słuchu u osób cierpiących z szumami usznymi
PublicationThis paper summarises the problem of tinnitus, hypotheses on its causes and the treatment methods. Moreover, a hypothesis on tinnitus origins is explained, based on the mechanisms of the analog-to-digital conversion and quantization. In addition, this paper describes methods of determining the acoustic intensity and spectra of low- level ultrasonic signals, as well as impedance characteristics of an ultrasound transducer. Furthermore,...
-
Magnetic and capacitive couplings influence on power losses in double circuit high voltage overhead transmission line
PublicationPurpose – The paper aims to discuss problems of power and energy losses in a double-circuit overhead transmission line. It was observed from energymeters’ readings, that in such a line, active power losses can be measured as “negative”. The “negative” active power losses appear when the active power injected to the circuit is lower than the active power received at the circuit end. The purpose of this paper is to explain this phenomenon. Theoretical...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublicationThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
An Analysis of Multistrip Line Configuration on Elliptical Cylinder
PublicationA configuration of multistrip lines mounted on a multilayer dielectric coated elliptic cylinder is investigated in this paper. A full-wave analysis and a moment-method calculation are employed. The analysis is carried out considering the expansion of the field as a series of Mathieu functions. Both open and shielded lines are considered in the analysis. Propagation coefficients and characteristic impedances are calculated for the...
-
The use of numerical methods for the analysis of phase phenomena in multi element antennas.
PublicationW artykule zostały zaprezentowane wyniki analizy wpływu wzajemnej i własnej impedancji promieniowania na fazę sygnału odbieranego przez antenę wieloelementową. Obliczenia dokonano dla elektrycznego modelu zastępczego Mason`a przetwornika ultradźwiękowego.
-
A Dual-Polarized 39 GHz 4x4 Microstrip Antenna Array for 5G MU-MIMO Airflight Cabin Connectivity
PublicationThis paper presents the design, fabrication, and experimental validation of a 39 GHz dual-polarized 4x4 microstrip antenna array. The array consists of 16 slot coupled circular microstrip patches, fed through SMPS connectors. The procedure requiring a reduced number of cables for measurement of the uniformly excited antenna array is also presented. The array exhibits 18 dBi peak gain and 2.9 GHz reflection bandwidth and is intended...
-
Odporność korozyjna staliwa wysokochromowego
PublicationBadano odporność korozyjną staliwa wysokochromowego w dwóch stanach: lanym i po obróbce cieplnej - hartowaniu i odpuszczaniu. Stwierdzono korzystny wpływ obróbki cieplnej na odporność korozyjną, ocenianą metodą badania polaryzacji i impedancji.
-
System do spektroskopii impedancyjnej z wykorzystaniem oscyloskopu cyfrowego.
PublicationW artykule przedstawiono alternatywną dla fabrycznych mierników impedancji metodę badań spektroskopowych materiałów biologicznych. System pomiarowy pozwala na osiągnięcie dużej dokładności pomiarów w szerokim zakresie częstotliwości, zwłaszcza w zakresie niskich częstotliwości.
-
Load introduction to composite columns revisited—Significance of force allocation and shear connection stiffness
PublicationThe AISC 360-16 Specification recommends that the design shear force between parts of a composite column in the load introduction area shall be calculated based on the force allocation at ultimate limit state. Applicability of this straightforward method to the load levels that usually arise in slender composite columns is questionable, as this capacity-based force allocation is only true when the axial force is equal to the plastic...
-
Modulacja 3D-SVPWM z kompensacją napięcia niezrównoważenia i balansowaniem napięć DC dla czterogałęziowego falownika 3L-NPC
PublicationPrzedstawiono realizację algorytmu modulacji napięcia 3D-SVPWM (ang. 3-Dimensional Space Vector Pulse Width Modulation) z kompensacją napięcia niezrównoważenia dla trójpoziomowego czterogałęziowego falownika 3L-NPC (ang. 3-Level Neutral-Point-diode-Clamped Converter). Do wyznaczania współczynników wypełnień w modulacji szerokości impulsów zastosowano liniowe funkcje kształtu czworościennego elementu skończonego z węzłami, których...
-
Tripping limitations of residual current devices in photovoltaic installations
PublicationIn electrical installations with photovoltaic sources of energy, earth fault current may comprise alternating current component and direct current component. The waveform shape of this earth fault current mainly depends on the point of the fault and the properties of a photovoltaic power electronics converter. The waveform shape of the current influences operation of protection devices, especially tripping threshold of residual...
-
Distribution Transformer with Multi-Zone Voltage Regulation for Smart Grid System Application
PublicationThe article presents four concepts of the multi-zone voltage regulation (MZVR) system. It is a combination of a distribution transformer with an on-load tap-changer, for step voltage regulation, and a power electronic converter, dimensioned for a fraction of MZVR power, realizing continuous voltage regulation, supplemented by a special switch, the so-called bypass. This allows voltage regulation at high resolution, wide range and...
-
Terbium Substituted Lanthanum Orthoniobate: Electrical and Structural Properties
PublicationThe results of electrical conductivity studies, structural measurements and thermogravimetric analysis of La1−xTbxNbO4+δ (x = 0.00, 0.05, 0.1, 0.15, 0.2, 0.3) are presented and discussed. The phase transition temperatures, measured by high-temperature x-ray diffraction, were 480 °C, 500 °C, and 530 °C for La0.9Tb0.1NbO4+δ, La0.8Tb0.2NbO4+δ, and La0.7Tb0.3NbO4+δ, respectively. The impedance spectroscopy results suggest mixed conductivity...
-
Optical glyphs based localization and identification system
PublicationThe paper presents a description of functioning of a platform supporting the detection of obstructive diseases in the respiratory system education process. A 16-parameter model of the respiratory system simulated in the MATLAB/Simulink environment was set in the role of the tested patient. It has been linked to the control layer, developed in the LabVIEW environment, using the SIT library (Simulation Interface Toolkit). This layer...
-
A detector of sleep disorders for using at home
PublicationObstructive sleep apnea usually requires all-ni ght examination in a specialized clinic, under the supervision of a medical staff. Because of those requirements it is an expensive and a non-widely utilized test. Moving the examination procedure to patients’ home with automatic analysis algorithms involved will decrease the costs and make it available for larger group of patients. The developed device allows all-night recordings...
-
Electrochemical investigations on the corrosion behaviour of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sulphuric acid
PublicationCorrosion is a major concern for most structural applications. Its detrimental effect significantly reduces the life of metallic components. This paper presents the results of an experimental investigation of corrosion in the steel reinforcement of concrete samples having three different substituents: 20% diatomite, 20% zeolite, and a reference without zeolite or diatomite. All concrete specimens were subjected to a solution of...
-
An application supporting the educational process of the respiratory system obstructive diseases detection
PublicationThe paper presents a description of functioning of a platform supporting the detection of obstructive diseases in the respiratory system education process. A 16-parameter model of the respiratory system simulated in the MATLAB/Simulink environment was set in the role of the tested patient. It has been linked to the control layer, developed in the LabVIEW environment, using the SIT library (Simulation Interface Toolkit). This layer...
-
Automatic tuning of a resonant circuit in wireless power supply systems for biomedical sensors
PublicationIn this paper, a tuning method of a resonant circuit suited for wireless powering of miniature endoscopic capsules is presented and discussed. The method allows for an automatic tuning of the resonant frequency and matching impedance of a full wave rectifier loading the resonant circuit. Thereby, the receiver tunes so as to obtain the highest power efficiency under given conditions of transmission. A prototype receiver for wireless...
-
Electrical conductivity of nanostructured acceptor-doped ceria fabricated by spark plasma sintering (SPS)
PublicationHigh purity nanoscale powders (~10–15 nm size) of two different compositions of ceria, doped with Gd3+ and Ca2+, have been consolidated by spark plasma sintering (SPS) at different temperatures. Fully-dense samples were observed only at a sintering temperature of 980 °C. The as-sintered samples showed rather fast grain growth with an average grain size below 300 nm. The electrical properties of the samples were evaluated by impedance...
-
Nested Kriging Surrogates for Rapid Multi-Objective Optimization of Compact Microwave Components
PublicationA procedure for rapid EM-based multi-objective optimization of compact microwave components is presented. Our methodology employs a recently developed nested kriging modelling to identify the search space region containing the Pareto-optimal designs, and to construct a fast surrogate model. The latter permits determination of the initial Pareto set, further refined using a separate surrogate-assisted process. As an illustration,...
-
Właściwości elektryczne szkło-ceramiki zawierającej ferroelektryczną fazę BiV
PublicationKompozyty szklano - ceramiczne zawierające nanokryształy posiadają właściwości fizyczne, które nie są możliwe do uzyskania w innych materiałach. Dzięki możliwości wytworzenia szkło - ceramik posiadających kryształy o różnej wielkości (nano, mikro...) i różnorodnego typu, można w istotny sposób kontrolować właściwości elektryczne takich materiałów. Stała dielektryczna faz ferroelektrycznych jest bardzo wrażliwa na zmiany rozmiarów...
-
Lamp of adjustable spectrum for photographic usage
PublicationPhotography is a unique rapidly growing interdisciplinary field encompassing aspects of science, art and technology. Expectations of photographers are steadily increasing with the development of technology. One of the areas playing a crucial role in photography is lighting. Consequently, several types of light sources for photographic use have been developed. The ongoing research in this field concentrates on lamps with tunable...
-
A Power-Efficient Digital Technique for Gain and Offset Correction in Slope ADCs
PublicationIn this brief, a power-efficient digital technique for gain and offset correction in slope analog-to-digital converters (ADCs) has been proposed. The technique is especially useful for imaging arrays with massively parallel image acquisition where simultaneous compensation of dark signal non-uniformity (DSNU) as well as photo-response non-uniformity (PRNU) is critical. The presented approach is based on stopping the ADC clock by...
-
Infrastruktura ładowania pojazdów elektrycznych
PublicationW artykule przedstawiono przegląd zagadnień z zakresu infrastruktury ładowania pojazdów elektrycznych. Przeanalizowano wpływ dużej liczby pojazdów EV na system elektroenergetyczny. W analizie uwzględniono zarówno wzrastające zapotrzebowanie na moc jak też na zapewnienie wysokiej jakości energii elektrycznej. Pokazano ideę wykorzystania pojazdów EV jako magazynów energii w systemie elektroenergetycznym. Zaprezentowano podstawowe...
-
Wyznaczanie właściwości uziemień metodami statycznymi, wysokoczęstotliwościowymi i udarowymi
PublicationW artykule przedstawiono różne metody pomiaru rezystancji statycznej i udarowej oraz impedancji uziemień. Przedstawiono wyniki badań porównawczych wykonanych przy użyciu metody statycznej, wysokoczęstotliwościowej oraz udarowej. Omówiono obszary zastosowań oraz ograniczenia omawianych metod.
-
Design and Optimization of a Compact Super-Wideband MIMO Antenna with High Isolation and Gain for 5G Applications
PublicationThis paper presents a super-wideband multiple-input multiple-output (SWB MIMO) antenna with low profile, low mutual coupling, high gain and compact size for microwave and millimeter wave (mm-wave) fifth-generation (5G) applications. A single antenna is a simple elliptical-square shape with a small physical size of 20 × 20 × 0.787 mm3. The combination of both square and elliptical shapes results in an exceptionally broad impedance...
-
Mechanizm korozji stopu Al-Si nadtapianego laserowo w niskiej temperaturze.
PublicationBadano odporność na korozję elektrochemiczną stopu Al-Si metodami krzywych polaryzacji i impedancji. Ujawniono wyraźny wzrost odporności na korozję stopu nadtapianego laserowo po schłodzeniu do niskiej temperatury. Zaproponowano mechanizm korozji warstwy wierzchniej stopu.
-
Elektros energetiniai irengimai ir instaliacija. Vadoelis aukstesniosiomsir profesinems mokykloms.
PublicationZawarto: domowe instalacje elektryczne; urządzenia oświetleniowe i grzejne;przemysłowe instalacje elektryczne niskiego napięcia; ochrona przeciwporażeniowa w urządzeniach niskiego napięcia; linie napowietrzne; linie kablowe;stacje elektroenergetyczne; elektrownie; przepięcia i ochrona odgromowa; ochrona przed pożarami i wybuchami; impedancje elementów toru przesyłu energii;obliczanie spadku napięcia oraz strat mocy i strat energii...
-
An Analysis of Probe-Fed Rectangular Patch Antennas With Multilayer and Multipatch Configurations on Cylindrical Surfaces
PublicationA multi-patch configuration of probe-fed rectangular microstrip antennas mounted on a cylindrical body, with electrically small radius, with an arbitrary number of substrate and superstrate layers is investigated in this paper. A full-wave analysis and a moment-method calculation are employed. A unified procedure for creating proper matrices for the investigated geometry of the structure is outlined here. Numerical results for...
-
Hybrid inductance-thyristor short-circuit current limiting devices
PublicationDla wartości prądu w gałęzi w której zainstalowane jest urządzenie jest mniejsza od prądu w dławiku urządzenia, dławik jest zwarty gałęzią z tyrystorem. Impedancja bieguna urządzenia hybrydowego jest praktycznie równa zero. W chwili wzrostu prądu w gałęzi z urządzeniem ograniczającym ponad tę wartość, do obwodu głównego wtrącona zostaje impedancja kolejno dwóch dławików, ograniczając bezzwłocznie dynamikę i amplitudę prądu zwarciowego....
-
Modulacja 3D-SVPWM dla przekształtników wielopoziomowych czterogałęziowych na bazie funkcji kształtu
PublicationPrzedstawiono realizację algorytmu modulacji napięcia 3D-SVPWM (ang. 3-Dimensional Space Vector Pulse Width Modulation) dla trójpoziomowego czterogałęziowego przekształtnika 3L-NPC (ang. 3-Level Neutral-Point-diode-Clamped Converter). Do wyznaczania współczynników wypełnień w modulacji szerokości impulsów zastosowano liniowe funkcje kształtu czworościennego elementu skończonego. Proponowany algorytm modulacji nie jest ograniczony...
-
Impulse and high frequency methods of lighting earthing testes.
PublicationUziemienia projektowane dla prądów zwarciowych nie zawsze są właściwe do odprowadzania prądów piorunowych, gdzie należy brać pod uwagę impedancję uziemień. W pracy porównano metody: udarową oraz wysokiej częstotliwości zastosowane do oceny przydatności uziemień odgromowych.
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublicationGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
Wpływ kształtu elektrody woltamperometrycznej na jej właściwości metrologiczne w dziedzinie czasu
PublicationW artykule omówiono właściwości metrologiczne elektrod woltamperometrycznych. Wykazano, że w przypadku oznaczania małych wartości stężeń jonów metali, elektrody te zachowują się tak jak przetworniki pomiarowe I rzędu. Ich właściwości metrologiczne opisuje czułość i stała czasowa. Wartości tych wielkości są uzależnione od mechanizmu transportu jonów do/od powierzchni elektrod oraz od ich kształtu. Wykonano symulacje wpływu kształtu...
-
Development of an emulation platform for synchronous machine power generation system using a nonlinear functional level model
PublicationThe article presents the Power Hardware in the Loop (PHIL) approach for an autonomous power system analysis based on the synchronous generator model incorporating magnetic saturation effects. The model was prepared in the MATLAB/Simulink environment and then compiled into the C language for the PHIL platform implementation. The 150 kVA bidirectional DC/AC commercial-grade converter was used to emulate the synchronous generator....
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublicationMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Effect of Thermal Shock During Legionella Bacteria Removal on the Corrosion Properties of Zinc-Coated Steel Pipes
PublicationThe purpose of this investigation was to conduct the failure analysis of a water-supply system made from zinc-coated steel. The observed corrosion process had an intense and complex character. The brownish deposits and perforations were present after 2-3 years of exploitation. The electrochemical study based on the Tafel polarization, corrosion potential monitoring, and electrochemical impedance spectroscopy together with microscopic...
-
Corrosion behavior of concrete produced with diatomite and zeolite exposed to chlorides
PublicationChloride induced reinforcement corrosion is widely accepted to be the most frequent mechanism causing premature degradation of reinforced concrete structures. The electrochemical impedance of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sodium chloride was assessed. Chemical, physical and mineralogical properties of three concrete samples (20% diatomite, 20% zeolite, and a reference containing neither)...
-
Performance of organic coatings upon cyclic mechanical load
PublicationA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Design and Performance Evaluation of the Energy Subsystem of a Hybrid Light andWave Energy Harvester
PublicationThe paper presents the design and performance of an energy subsystem (ES) dedicated to hybrid energy harvesters (HEHs): wave energy converters (WECs) combined with photovoltaic panels (PVPs). The considered ES is intended for compact HEHs powering autonomous end-node devices in distributed IoT networks. The designed ES was tested experimentally and evaluated in relation to the mobile and wireless distributed communication use case....
-
Pipelined Two-Operand Modular Adders
PublicationPipelined two-operand modular adder (TOMA) is one of basic components used in digital signal processing (DSP) systems that use the residue number system (RNS). Such modular adders are used in binary/residue and residue/binary converters, residue multipliers and scalers as well as within residue processing channels. The structure of pipelined TOMAs is usually obtained by inserting an appropriate number of pipeline register layers within...
-
Dynamiczna aplikacja Internetowa ASP.NET silnika indukcyjnego jako elementu wirtualnego laboratorium maszyn elektrycznych
PublicationTematem referatu jest dynamiczna aplikacja internetowa, która umożliwia symulację obwodową silnika indukcyjnego trójfazowego Sg 100 L2 z wykorzystaniem interfejsu przeglądarki WWW. Model matematyczny silnika jest zdefiniowany w tzw. osiach naturalnych i sformułowany na podstawie metody energetycznej Lagrange’a. Do implementacji modelu maszyny w aplikacji internetowej wybrano projekt typu Web Forms, który jest składnikiem środowiska...
-
Różnicowa tomografia impedancyjna
PublicationW pracy zaprezentowano ideę obrazowania obiektów trójwymiarowych przy pomocy pomiaru impedancji na jego punktach brzegowych. W pracy pokazano podstawy obrazowania przy użyciu pomiaru z wykorzystaniem dwu częstotliwości jednocześnie , pokazano algorytmy rekonstrukcji i przykładowy system pomiarowy wykorzystujący zaproponowaną technikę.
-
Testing of the Superconducting Magnets Frequency Characteristics
PublicationPrzedstawiono zagadnienia związane z opracowaniem systemu do wyznaczania impedancji uzwojeń magnesów nadprzewodzących w funkcji częstotliwości. Omówiono strukturę sprzętową systemu, oprogramowanie oraz sposób wyznaczania parametrów badanego uzwojenia. Pokazano przykładowe wyniki uzyskane przy użyciu omawianego systemu w GSI w Darmstadt.
-
Fast synthesis of coupled-resonator filters.
PublicationZaproponowana została nowa, szybko zbieżna technika syntezy macierzy sprzężneń filtrów wykorzystujących rezonatory sprzężone. Metoda jest sformułowana jako nieliniowy problem najmniejszych kwadratów, optarty o zera i bieguny zwarciowej impedancji wejsciowej i wyjściowej oraz wartości własnych macierzy sprzężeń i jej podmacierzy.
-
Badania nowego czujnika wilgotności z filmem polimerowym
PublicationW pracy przedstawione zostały wyniki pomiarów widm impedancji czujników wilgotności z epoksydowymi filmami polimerowymi, zawierającymi czułe na wilgoć czwartorzędowe sole amoniowe. Filmy spreparowano z polietylenoiminy (PEI), usieciowanej przy pomocy eteru diglicydylowego 1,4-butanodiolu (BDDGE) z dodatkiem chlorku trójmetyloamoniowoglicydylowego (GTMAC).
-
Anna Golijanek-Jędrzejczyk dr inż.
People -
Non-linear electrical properties of myocardium in computer simulation
PublicationPomiar impedancji elektrycznej jest obiecującą metodą monitorowania stanu mięśnia sercowego, szczególnie podczas niedokrwienia. Typową metodą pomiaru jest rejestrowanie odpowiedzi-napięcia na pobudzenie prądowe. Odpowiedź jest często aproksymowana jako liniowa względem pobudzenia. Artykuł jest poświęcony oszacowaniu rzędu wielkości nieliniowych komponentów w odpowiedzi.
-
Ryszard Katulski prof. dr hab. inż.
People -
Comparison of road and laboratory measurements of tyre/road noise
PublicationTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...