displaying 1000 best results Help
Search results for: addiction
-
Photogrammetric and total station's measurement of compressed column's model
PublicationModelling studies continue to play an important role. One of such study is stress determination in the reinforcement bars of reinforced columns and determine column's axis deformation. The article presents measurements results of control points located on the model of reinforced concrete column. The column was compressed in few series till it's destruction. In this studies, photogrammetric method and total station measurements...
-
Rapid and Green Separation of Mono- and Diesters of Monochloropropanediols by Ultrahigh Performance Supercritical Fluid Chromatography–Mass Spectrometry Using Neat Carbon Dioxide as a Mobile Phase
PublicationThis study demonstrates the effect of column selectivity and density of supercritical carbon dioxide (SC-CO2) on the separation of monochloropropanediol (MCPD) esters, known as food toxicants, using SC-CO2 without addition of cosolvent in ultrahigh performance supercritical fluid chromatography–mass spectrometry (UHPSFC-MS). This study shows that over 20 2-monochloropropanediol (2-MCPD) and 3-monochloropropanediol (3-MCPD) mono-...
-
Turán numbers for odd wheels
PublicationThe Turán number ex(n,G) is the maximum number of edges in any n-vertex graph that does not contain a subgraph isomorphic to G. A wheel W_n is a graph on n vertices obtained from a C_{n−1} by adding one vertex w and making w adjacent to all vertices of the C_{n−1}. We obtain two exact values for small wheels: ex(n,W_5)=\lfloor n^2/4+n/2\rfloor, ex(n,W_7)=\lfloor n^2/4+n/2+1 \rfloor. Given that ex(n,W_6) is already known, this...
-
Solid phase microextraction–comprehensive twodimensional gas chromatography–time-of-flight mass spectrometry: a new tool for determining PAHs in airport runoff water samples
Publicationfundamental aspect of airport operations is the pollution caused by airport runoff waters. Polycyclic aromatic hydrocarbons (PAHs) are one of the most important groups of xenobiotics which are commonly found in runoff water originating from airports. Only very limited data on the analysis of airport runoff water have been published until now. Therefore, a reliable and accurate analytical method based on headspace solid-phase microextraction...
-
Modeling the global atmospheric transport and deposition of mercury to the Great Lakes
PublicationMercury contamination in the Great Lakes continues to have important public health and wildlife ecotoxicology impacts, and atmospheric deposition is a significant ongoing loading pathway. The objective of this study was to estimate the amount and source-attribution for atmospheric mercury deposition to each lake, information needed to prioritize amelioration efforts. A new global, Eulerian version of the HYSPLIT-Hg model was used...
-
Impedance Measurement and Selection of Electrochemical Equivalent Circuit of a Working PEM Fuel Cell Cathode
PublicationThe dynamic impedance analysis of direct methanolfuel cell (DMFC) cathode supplied with pure oxygen is pre-sented. Presented results were obtained during dynamic chang-es of the current density in working fuel cell. Investigation ofthe occurring processes at cathode was carried with dynamicelectrochemical impedance spectroscopy (DEIS). A discussionwas conducted based on the determined correlation parameterχ2. It was shown that...
-
Towards the Application of Structure-Property Relationship Modeling in Materials Science: Predicting the Seebeck Coefficient for Ionic Liquid/Redox Couple Systems
PublicationThis work focuses on determining the influence of both ionic liquid (IL) type and redox couple concentration on Seebeck coefficient values of such a system. The quantitative structure property relationship (QSPR) and read-across techniques are proposed as methods to identify structural features of ILs (mixed with LiI/I2 redox couple), which have the most influence on the Seebeck coefficient (Se) values of the system. ILs consisting...
-
Big Data Analytics for ICT Monitoring and Development
PublicationThe expanded growth of information and communication technology has opened new era of digitization which is proving to be a great challenge for researchers and scientists around the globe. The utmost paradigm is to handle and process the explosion of data with minimal cost and discover relevant hidden information in the least amount of time. The buzz word “BIG DATA” is a widely anticipated term with the potential to handle heterogeneous,...
-
Using Principal Component Analysis and Canonical Discriminant Analysis for multibeam seafloor characterisation data
PublicationThe paper presents the seafloor characterisation based on multibeam sonar data. It relies on using the integrated model and description of three types of multibeam data obtained during seafloor sensing: 1) the grey-level sonar images (echograms) of seabed, 2) the 3D model of the seabed surface which consists of bathymetric data, 3) the set of time domain bottom echo envelopes received in the consecutive sonar beams. The classification...
-
Bacterial cellulose vs. bacterial cellulose nanocrystals as stabilizer agents for O/W pickering emulsions
PublicationThe growing interest in Pickering emulsions in functional food systems resulted in the need to find suitable stabilizers for them. The work considers the use of bacterial cellulose for this purpose, and its aim was to compare the properties of disintegrated bacterial cellulose, before and after freeze-drying, and its nanocrystals obtained using H2SO4 under variable of time and concentration conditions. The structure of nanocrystals...
-
Study on effective front region thickness of PCM in thermal energy storage using a novel semi-theoretical model
PublicationThermal energy storage in mobile applications, particularly battery of electric vehicles, is currently gaining a lot of importance. In this paper, a semi-theoretical time-dependent mathematical model of the phase change in a double shell thermal energy storage module has been developed where the inner tube is a heat exchange surface. An effective front region thickness for the melting and solidification process has been studied....
-
Ion Chromatography with Pulsed Amperometric Detection for Determining Cyanide in Urine and Meconium Samples
PublicationThe parents’ addictions and eating habits have a significant influence on the child’s growth. The first stool of a newborn baby provides a large amount of information about xenobiotics transmitted by the mother’s body. The analytical technique used in the study is ion chromatography with pulsed amperometric detection (IC-PAD). The biological samples, which were obtained from women staying in a maternity ward and their partners,...
-
Hanna Gaweł
PeopleHanna is a PhD student at the Doctoral School in Social Sciences in the discipline of Social Communication and Media Sciences at the Jagiellonian University and is employed as an Assistant at the Institute of Information Studies of the said university. She received her Master's degree from Jagiellonian University, where she studied Information Management at the Faculty of Management and Social Sciences. Her Bachelor's degree was...
-
Engineering Challenges in the Design of Cochlear Implants
PublicationHearing aids such as cochlear implants have been used by both adults and children for a long time. In addition, cochlear implants are used by patients who have severe hearing loss either by birth or after an accident. This paper aims to investigate the engineering challenges bounding the design of cochlear implants and present its possible solution...
-
Application of Fracture Mechanics for Energetic Effects Predictions While Wood Sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (or power - more interesting from energetic point of view) could be considered from a point of view of modern fracture mechanics. Cutting...
-
Characterization and properties of LDPE/(ground tire rubber)/crosslinked butyl rubber blends
PublicationIn recent years, interest in used rubber recycling, mainly focusing on the utilization of end-of-life tires, has heightened. This interest, is owing to the activities related to environmental protection and economic factors, which both stimulate companies to reuse the high-quality rubber present in ground rubber scrap. In this study, the application of crosslinked butyl rubber in thermoplastic compositions of low-density polyethylene...
-
Bioactive compounds and the antioxidant capacity in new kiwi fruit cultivars
PublicationThe aim of this investigation was to find the best among seven different kiwi fruit cultivars (‘Hayward’, ‘Daheung’, ‘Haenam’, ‘Bidan’, ‘Hort16A’, ‘Hwamei’ and ‘SKK12’) for human consumption and to classify them as groups. Therefore, the contents of bioactive compounds and the level of antioxidant capacities of these cultivars were determined in four different extracts and compared. It was found that the contents of the bioactive...
-
Transport properties of aqueous ionic liquid microemulsions: influence of the anion type and presence of the cosurfactant
PublicationTransport properties, viz. specific conductivity, dynamic viscosity and apparent diffusion coefficients, were measured as a function of water content in aqueous ionic liquid microemulsions containing 1-butyl-3- methylimidazolium hexafluorophosphate, [BMIM][PF6] and bis(trifluoromethanesulphonyl)imide, [BMIM][Tf2N], stabilized by the nonionic surfactant TX-100, or its mixture with a cosurfactant, i.e. butanol. The investigation covered...
-
Analysis of Airport Runoff Waters
PublicationA particularly important facet of airport operation is the impact of the pollution caused byrunoff waters. Runoff waters at an airport may contain relatively high concentrations of differentcontaminants resulting from the various aspects of its operation: de/anti-icing operations,washing and cleaning operations, spills of fuel and lubricants, exhaust fumes, and weed removal.The pollution caused by airport operations affects soil,...
-
Market Size, Competitiveness and Technological Frontier - the Impact of Trade Integration with the UE on Productivity in Polish Manufacturing Sectors
PublicationThis paper addresses the relationship between growth of relative productivity in Polish manufacturing sectors and forces stemming from trade integration with the EU. We look at the productivity growth from the perspective of relations between Polish manufacturing sectors and the foreign ones, focusing on partner countries from the enlarged EU. Empirical analysis is based on sector level bilateral data concerning both domestic (Polish)...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublicationThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Remote communication in Scrum teams - a COVID-19 preventive measure or work time optimisation?
PublicationThe article presents the impact of remote work, resulting from the COVID-19 pandemic, on the functioning of Scrum teams. Attempts have been made to analyse the positive and negative aspects of remote work. The article also looks at the impact of remote work on the level of communication and efficiency of Scrum teams. For this purpose, the author conducted research on a sample of 40 organisations that declared to use Scrum methodology,...
-
Nickel-nanodiamond coatings electrodeposited from tartrate electrolyte at ambient temperature
PublicationIn this study, nanocrystalline Ni and Ni-diamond coatings were obtained by electrodeposition from tartrate electrolyte at ambient temperature aiming at improving corrosion and wear properties of the material. The created surfaces were investigated with regard to microhardness, adhesion, wear- and corrosion-resistance. The various methods such as atomic force microscopy, scanning electron microscopy, electrochemical impedance spectroscopy...
-
A numerical analysis of the thermal effects in the jet impingement stagnation zone
PublicationMost of the flows occurring in the engineering systems are turbulent and their accurate numerical analysis is still challenging, especially when combined with the heat transfer. One of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied also in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to its...
-
Expedited Feature-Based Quasi-Global Optimization of Multi-Band Antenna Input Characteristics with Jacobian Variability Tracking
PublicationDesign of modern antennas relies—for reliability reasons—on full-wave electromagnetic simulation tools. In addition, increasingly stringent specifications pertaining to electrical and field performance, growing complexity of antenna topologies, along with the necessity for handling multiple objectives, make numerical optimization of antenna geometry parameters a highly recommended design procedure. Conventional algorithms, particularly...
-
Deodorization of model biogas by means of novel non-ionic deep eutectic solvent
PublicationThe paper presents new non-ionic deep eutectic solvent (DES) composed of natural and non-toxic components i.e. guaiacol, camphor and levulinic acid in 1:1:3 molar ratio as a promising absorbent for removal of selected volatile organic compounds (VOCs) including dichloromethane, toluene, hexamethyldisiloxane and propionaldehyde from model biogas. The affi nity of DES for VOCs was determined as vapour-liquid coeffi cients and the...
-
Simultaneous Removal of Hexane and Ethanol from Air in a Biotrickling Filter—Process Performance and Monitoring Using Electronic Nose
PublicationBiofiltration is a well-accepted method for the removal of malodorous compounds from air streams. Interestingly, the mechanisms underlying this process are not fully understood. The aim of this paper was to investigate the simultaneous removal of hydrophobic hexane with hydrophilic ethanol, resulting in the enhanced removal of hexane in the presence of ethanol. Investigations were performed in a peat-perlite packed biotrickling...
-
Bio-mitigation of organic pollutants using horseradish peroxidase as a promising biocatalytic platform for environmental sustainability
PublicationA wide array of environmental pollutants is often generated and released into the ecosystem from industrial and human activities. Antibiotics, phenolic compounds, hydroquinone, industrial dyes, and Endocrine-Disrupting Chemicals (EDCs) are prevalent pollutants in water matrices. To promote environmental sustainability and minimize the impact of these pollutants, it is essential to eliminate such contaminants. Although there are...
-
Improving carbon dioxide capture in aqueous ammonia solutions by fine SiO2 particles
PublicationAmmonia solutions are considered to be effective solvents for carbon dioxide absorption. Despite the numerous advantages of these solvents, their high volatility is a significant technical and economic problem. Therefore, in this work, silica particles were used as additives to improve CO2 absorption and inhibit NH3 desorption. SiO2 microparticles and colloidal SiO2 particles in the concentration range of 0-0.15 wt.% were used...
-
Optimization of a Fabric Phase Sorptive Extraction protocol for the isolation of six bisphenols from juice pouches to be analysed by high performance liquid chromatography coupled with diode array detector
PublicationFabric Phase Sorptive Extraction (FPSE) combined with high pressure liquid chromatography using to diode array detection (HPLC-DAD) was applied for the simultaneous determination of bisphenols (BPA, BPB, BPC, BPE, BPF, BPS) in juice pouches. The FPSE procedure was optimized with regards to the critical parameters that affect the performance of the method including the selection of the FPSE membrane type and size, adsorption time,...
-
Application of 3D- printed hydrogels in wound healing and regenerative medicine
PublicationHydrogels are three-dimensional polymer networks with hydrophilic properties. The modifiable properties of hydrogels and the structure resembling living tissue allow their versatile application. Therefore, increasing attention is focused on the use of hydrogels as bioinks for three-dimensional (3D) printing in tissue engineering. Bioprinting involves the fabrication of complex structures from several types of materials, cells,...
-
Social Media in the Fashion Industry. Fundamentals, Strategy and Research Methods
PublicationThis book introduces social network fundamentals in the fashion domain. It addresses the creation of social media marketing plans, highlighting strategic approaches that allow fashion brands to differentiate themselves in the ephemeral and challenging fashion context. Through a variety of academic and professional sources and by sharing the results of their own research, the authors present research methodologies, including netnography,...
-
Isolation and structure of a covalent cross-link adduct between mitomycin C and DNA
PublicationA DNA cross-link adduct of the antitumor agent mitomycin C (MC) to DNA has been isolated and characterized; the results provide direct proof for bifunctional alkylation of DNA by MC. Exposure of MC to Micrococcus luteus DNA under reductive conditions and subsequent nuclease digestion yielded adducts formed between MC and deoxyguanosine residues. In addition to the two known monoadducts, a bisadduct was obtained. Reductive MC activation...
-
POLAND’S ENERGY DEPENDENCE AT THE TURN OF THE 21ST CENTURY
PublicationThe following article is an attempt to assess Poland's energy independence in the years 1993-2020. The main aim of the paper is to present Poland's dependence on raw materials from foreign partners - in the field of imports of electricity, natural gas, crude oil, non-renewable energy resources, i.e., hard coal and lignite, and the country's dynamics in the amount of imports. In addition, the aim of the work is to answer research...
-
Carbon nitride exfoliation for photocatalysis and photocatalytic ozonation over emerging contaminants abatement
PublicationThe production of graphitic carbon nitride was studied with the addition of a following exfoliation step using ultrasounds, at different times. The treatment produced catalysts with much higher surface areas, from 2.18 m2 g 1 with no treatment to 28.34 m2 g 1 after 36 h of exfoliation. During exfoliation, melem was also produced, and may further enhance the photoluminescence and photocatalytic properties. The photocatalytic reaction...
-
Magnetic deep eutectic solvents – Fundamentals and applications
PublicationMagnetic deep eutectic solvents (MDES), a relatively new subclass of conventional deep eutectic solvents (DES) containing additional paramagnetic components in their structure. MDES exhibit a strong response toward external magnetic fields, thus they can improve many industrial and analytical applications. In addition, this new group of solvents present unique physicochemical properties that can be easily tuned by selecting the...
-
High-density Polyethylene - Expanded Perlite Composites: Structural Oriented Analysis of Mechanical and Thermomechanical Properties
PublicationAs part of this work, research was carried out on the effect of the addition of expanded perlite (PR) on the mechanical and thermomechanical properties of high-density polyethylene (PE) composites. Composites containing from 1 to 10 wt% of the inorganic filler were produced. Polyethylene-based composites manufactured by twin-screw extrusion and formed in the compression molding process were subjected to mechanical, thermomechanical,...
-
Impact of blending with polystyrene on the microstructural and electrochemical properties of SiOC ceramic
PublicationIn this work, we present the electrochemical behavior and microstructural analysis of silicon oxycarbide (SiOC) ceramics influenced by an addition of polystyrene (PS). Polymer-derived ceramics were obtained by pyrolysis (1000°C, Ar atmosphere) of different polysiloxanes prepared by sol–gel synthesis. This method is very effective to obtain desired composition of final ceramic. Two alkoxysilanes phenylthriethoxysilane and diphenyldimethoxysilane...
-
Graphical interface adaption for children to explain astronomy proportions and distances
PublicationMobile Science Center is a Polish project that seeks to bring astronomy knowledge to wider social groups through various applications. In its development it is necessary to design a graphical interface that explains a concept that is difficult to assimilate such as spatial proportions and distances. This paper develops a framework to create graphical representations that explain this learning to the target audience of children....
-
Estimation of Vehicle Energy Consumption at Intersections Using Microscopic Traffic Models
PublicationThis paper addresses issues related to modeling energy consumption and emissions using microscopic traffic simulations. This paper develops a method in which a traffic model is used to calculate the energy needed to travel through selected types of intersections. This paper focuses on energy consumption and derived values of calculated energy, which can be, for example, carbon dioxide emissions. The authors present a review of...
-
TiO2-C nanocomposite synthesized via facile surfactant-assisted method as a part of less energy-consuming LED-based photocatalytic system for environmental applications
PublicationA novel facile method was used to incorporate carbon into the titania structure. An alternative synthesis method of carbon-doped TiO2 has been proposed by using a widely used and cheap surfactant. During the process, cetyltrimethylammonium bromide plays a dual role, as a morphology modifier and as a carbon source. The presented approach allows obtained TiO2-C nanostructures to be anatase nanocrystals with carbon being deposited...
-
Tensor Decomposition for Imagined Speech Discrimination in EEG
PublicationMost of the researches in Electroencephalogram(EEG)-based Brain-Computer Interfaces (BCI) are focused on the use of motor imagery. As an attempt to improve the control of these interfaces, the use of language instead of movement has been recently explored, in the form of imagined speech. This work aims for the discrimination of imagined words in electroencephalogram signals. For this purpose, the analysis of multiple variables...
-
VOCs absorption from gas streams using deep eutectic solvents – A review
PublicationVolatile organic compounds (VOCs) are one of the most severe atmospheric pollutants. They are mainly emitted into the atmosphere from anthropogenic sources such as automobile exhaust, incomplete fuel combustion, and various industrial processes. VOCs not only cause hazards to human health or the environment but also adversely affect industrial installation components due to their specific properties, i.e., corrosive and reactivity....
-
Silver nanoparticles induce premutagenic DNA oxidation that can be prevented by phytochemicals from Gentiana asclepiadea
PublicationAmong nanomaterials, silver nanoparticles (AgNPs) have the broadest and most commercial applications due to their antibacterial properties, highlighting the need for exploring their potential toxicity and underlying mechanisms of action. Our main aim was to investigate whether AgNPs exert toxicity by inducing oxidative damage to DNA in human kidney HEK 293 cells. In addition, we tested whether this damage could be counteracted...
-
Mg2+ Doping Effects on the Structural and Dielectric Properties of CaCu3Ti4O12 Ceramics Obtained by Mechanochemical Synthesis
PublicationIn this study, ceramic CaCu3Ti4O12 (CCTO) and CaCu3−xMgxTi4O12 solid solutions in which 0.1 ≤ x ≤ 0.5 were prepared by the mechanochemical method, realized by a high‐energy ball milling technique. The effects of the Mg2+ ion concentration and sintering time on the dielectric response in the prepared ceramics were investigated and discussed. It was demonstrated that, by the use of a sufficiently high energy of mechanochemical treatment,...
-
Incomplete Cross-Bonding in the MV Line. Experience from the Operation of MV Single Cable Lines
PublicationCable lines are one of the basic components of power systems. Medium and high voltage cables mainly comprise a metallic sheath, which is concentric to the main core conductor. There are several operating schemes of such cable lines, which differ in the place of earthing of sheaths and the possible use of the sheaths and/or conductors crossing. The sheaths cross-bonding is typically done in two places of one cable line section,...
-
Activation of peroxymonosulfate using carbon black nano-spheres/calcium alginate hydrogel matrix for degradation of acetaminophen: Fe3O4 co-immobilization and microbial community response
PublicationHerein, we focused on the degradation of acetaminophen (ACT) drug in liquid phase by peroxymonosulfate (PMS) activated by carbon black nano-spheres (CBNS). The nanostructured activator was immobilized into calcium alginate hydrogel matrix (CAHM) to avoid the washout of the fine nanostructures. The Langmuir modeling showed an insignificant contribution to the adsorption process in the removal of ACT. The basic pH conditions favored...
-
Material Identification of the Human Abdominal Wall Based On the Isogeometric Shell Model
PublicationThe human abdominal wall is an object of interest to the research community in the context of ventral hernia repair. Computer models require a priori knowledge of constitutive parameters in order to establish its mechanical response. In this work, the Finite Element Model Updating (FEMU) method is used to identify an heterogeneous shear modulus distribution for a human abdominal wall model, which is based on nonlinear isogeometric...
-
High temperature proton conduction in LaSbO4
PublicationLanthanum orthoantimonate was synthesized using a solid‐state synthesis method. To enhance the possible protonic conductivity, samples with the addition of 1 mol% Ca in La‐site, were also prepared. The structure was studied by the means of X‐ray diffraction, which showed that both specimens were single phase. The materials crystallized in the space group P2 1 /n. Dilatometry revealed that material expands non‐linearly with the...
-
Multi-functional sensor based on photonic crystal fiber using plasmonic material and magnetic fluid
PublicationA unique highly sensitive photonic crystal fiber is investigated based on plasmonic material and magnetic fluid (MF) for the simultaneous measurement of temperature and magnetic field sensor. The designed sensor is explored by tracing the different parameters such as birefringence, coupling length, power spectrum, and the peak wavelength of the transmission intensity. The magnetic field and temperature computation are attained...