Filters
total: 4733
-
Catalog
displaying 1000 best results Help
Search results for: ADIABATIC HEATING
-
Evaluation of water turbine hydrodynamic thrust bearing performance on the basis of thermoelastohydrodynamic calculations and operational data.
PublicationW pracy przedstawiono analizę konstrukcji łożyska wzdłużnego turbiny wodnej. Łożysko zostało skonstruowane około 50 lat temu, a jego konstrukcja przewiduje kompensację termicznych odkształceń klocków. W analizie uwzględniono odkształcenia łożyska i wymianę ciepła w filmie smarowym i klockach łożyskowych. Poza obecną konstrukcją łożyska przeprowadzono również studium wpływu podstawowych parametrów konstrukcyjnych: grubości klocka...
-
Influence of hydrostatic pump operation period on performance of a thrust bearing of a 125 MW pump-turbine.
PublicationW pracy przedstawiono wyniki badań eksploatacyjnych łożysk wzdłużnych pompoturbin 125 MW elektrowni szczytowo pompowej (esp) Żar. W celu oceny warunków pracy łożysk wyposażono je w segmenty pomiarowe umożliwiające pomiary temperatury i położenia segmentu. W pracy omówiono konstrukcję i wyposażenie segmentu badawczego, metodykę wyznaczania charakterystycznych wielkości. Omówiono także wyniki badań wpływu czasu pracy pompy hydrostatycznego...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Evaluation of adhesion strength, corrosion, and biological properties of the MWCNT/TiO2 coating intended for medical applications
PublicationMulti-wall carbon nanotube (MWCNT) coatings are gaining increasing interest because of their special properties used in many science fields. The titania coatings are known for their improvement of osteoblast adhesion, thus changing the surface architecture. Bi-layer coatings comprising 0.25 wt% of the MWCNTs and 0.30 wt% of titania (anatase structure) were synthesized in a two-stage procedure using the electrophoretic deposition...
-
Justifying the prolongation of the service life of the bearing structure of a tank car when using Y25 bogies
PublicationThis paper substantiates the use of Y25 bogies under tank cars in order to prolong their service life. The reported study has been carried out for a tank car with rated parameters, as well as the actual ones, registered during full-scale research. Mathematical modeling was performed to determine the basic indicators of the tank car dynamics. The differential equations of motion were solved by a Runge-Kutta method using the Mathcad...
-
Bridge Non-Destructive Measurements Using a Laser Scanning during Acceptance Testing: Case Study
PublicationOwing to the recent proliferation of inventory works on roads and railways, bridge acceptance tests have increased exponentially. These tests’ results are often misinterpreted owing to the use of various measuring equipment types, rendering integrated interpretation problematic. It is also problematic that adjusting the measurement method is difficult when the structure’s response to load is uncertain. Therefore, it is important...
-
Framework for extracting rails and setting-out railway line axis based on UAV photogrammetric measurements
PublicationTechnical diagnostics enables assessing the current technical condition of a railway line and adjacent infrastructure, and forecasting its changes over a specific time horizon. One of its elements is the periodic monitoring of rail position and their geometry. This article presents a new framework for the setting-out of a railway track axis. The process presented in the manuscript is based on the specific filtration and extraction...
-
Deep eutectic solvents microbial toxicity: Current state of art and critical evaluation of testing methods
PublicationDeep eutectic solvents (DESs) were described at the beginning of 21st century and they consist of a mixture of two or more solid components, which gives rise to a lower melting point compared to the starting materials. Over the years, DESs have proved to be a promising alternative to traditional organic solvents and ionic liquids (ILs) due to their low volatility, low inflammability, easy preparation, and usually low cost of compounds...
-
A novel method of creating thermoplastic chitosan blends to produce cell scaffolds by FDM additive manufacturing
PublicationDue to its remarkable and promising biological and structural properties, chitosan has been widely studied in several potential applications in the biomedical sector. Attempts are being made to use this polymer and its properties in thermoplastics dedicated to 3D printing in FDM technology. However, chitosan can be processed only from acid solution, which limits its applications. The paper presents a new path for the production...
-
Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects
PublicationMetallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...
-
Path integrals formulations leading to propagator evaluation for coupled linear physics in large geometric models
PublicationReformulating linear physics using second kind Fredholm equations is very standard practice. One of the straightforward consequences is that the resulting integrals can be expanded (when the Neumann expansion converges) and probabilized, leading to path statistics and Monte Carlo estimations. An essential feature of these algorithms is that they also allow to estimate propagators for all types of sources, including initial conditions....
-
Buckling Analysis of a Micro Composite Plate with Nano Coating Based on the Modified Couple Stress Theory
PublicationThe present study investigates the buckling of a thick sandwich plate under the biaxial non-uniform compression using the modified couple stress theory with various boundary conditions. For this purpose, the top and bottom faces are orthotropic graphene sheets and for the central core the isotropic soft materials are investigated. The simplified first order shear deformation theory (S-FSDT) is employed and the governing differential...
-
The Application Of A Noise Mapping Tool Deployed In Grid Infrastructure For Creating Noise Maps Of Urban Areas
PublicationThe concept and implementation of the system for creating dynamic noise maps in PL-Grid infrastructure are presented. The methodology of dynamic acoustical maps creating is introduced. The concept of noise mapping, based on noise source and propagation models, was developed and employed in the system. The details of incorporation of the system to the PL-Grid infrastructure are presented. The results of simulations performed by...
-
Quantum Steering Inequality with Tolerance for Measurement-Setting Errors: Experimentally Feasible Signature of Unbounded Violation
Publicationuantum steering is a relatively simple test for proving that the values of quantum-mechanical measurement outcomes come into being only in the act of measurement. By exploiting quantum correlations, Alice can influence — steer — Bob ’ s physical system in a way that is impossible in classical mechanics, as shown by the violation of steering inequalities. Demonstrating this and similar quantum effects for systems of increasing size,...
-
A method for testing the wide-sense stationary uncorrelated scattering assumption fulfillment for an underwater acoustic channel
PublicationWide-sense stationary and uncorrelated scattering (WSSUS) assumptions are often applied for the statistical description of wireless communication channels. However, in the case of underwater acoustic channels the WSSUS model is of limited value. The degree of similarity of in-phase and quadrature components of the channel impulse response, measured with the use of bandpass modulated signals, can be used as an indicator of WSSUS...
-
Analysis of pavement structure sensitivity to passage of oversized heavy duty vehicle in terms of bearing capacity
PublicationOversized heavy duty vehicles occur in traffic very rarely but they reach extremely high weights, even up to 800 tonne. The detrimental impact of these vehicles on pavement structure is much higher than in case of commercial vehicles that comprise typical traffic, thus it is necessary to assess the sensitivity of pavement structure to passage of oversized vehicles. The paper presents results of sample calculations of load equivalency factor...
-
A Set of Low-power Microcontroller-based Modules Used for Testing of Small Energy Measurement Methods
PublicationEstimation of energy consumption of low-power devices is not widely discussed in the scientific literature, but this topic is getting more and more popular. Evaluation process of newly developed methods and instrumentation requires carefull treatment. In order to fulfill this niche, the set of micro-power microcontroller based devices was proposed. The devices represent typical energy consuption profiles and allow experimental verification...
-
Low Cost Hexacopter Autonomous Platform for Testing and Developing Photogrammetry Technologies and Intelligent Navigation Systems
PublicationLow-cost solutions for autonomous aerial platforms are being intensively developed and used within geodetic community. Unmanned aerial vehicles are becoming very popular and widely used for photogrammetry and remote sensing applications. Today’s market offers an affordable price components for unmanned solution with significant quality and accuracy growth. Every year market offers a new solutions for autonomous platforms with better...
-
THE USE OF THE Ti-13Zr-13Nb ALLOY POWDER FOR MANUFACTURING OF PROSTHETIC PARTS BY SELECTIVE LASER MELTING
PublicationThe 3D printing is a manufacturing technique belonging to the additive methods able to prepare the designed parts for various purposes. The present reasearch was aimed to fabricate the prosthetic foundations and bridges made of the new Ti-13Zr-13Nb alloy by the selective laser melting (SLM) of a metal powder. The scanning electron examinations and micro scanning tomography were used to investigate the surface quality and intrinsic...
-
High temperature oxidation behavior of SUS430 SOFC interconnects with Mn-Co spinel coating in air
PublicationIn this study, SUS430 alloy is evaluated for its high temperature corrosion properties as a possible material for interconnects of solid oxide fuel cells (SOFCs). Samples are coated with Mn-Co by commercial physical vapor deposition (PVD) process and oxidized in air for 1250 h at 800 °C. A dense cubic Mn-Co-Fe spinel layer is formed on the surface, showing great effect on corrosion reduction compared with the samples without coating....
-
Preparation and Characterization of Microsphere ZnO ALD Coating Dedicated for the Fiber-Optic Refractive Index Sensor
PublicationWe report the fabrication of a novel fiber-optic sensor device, based on the use of a microsphere conformally coated with a thin layer of zinc oxide (ZnO) by atomic layer deposition (ALD), and its use as a refractive index sensor. The microsphere was prepared on the tip of a single-mode optical fiber, on which a conformal ZnO thin film of 200 nm was deposited using an ALD process based on diethyl zinc (DEZ) and water at 100 °C....
-
Improving the procedure of probabilistic load testing design of typical bridges based on structural response similarities
PublicationThis paper concerns load testing of typical bridge structures performed prior to operation. In-situ tests of a two-span post-tensioned bridge loaded with three vehicles of 38-ton mass each formed the input of this study. On the basis of the results of these measurements, an advanced FEM model of the structure was developed for which the sensitivity analysis was performed for chosen uncertainty sources. Three uncorrelated random...
-
A method of self-testing of an analog circuit terminated by an ADC in electronic embedded systems controlled by microcontrollers
PublicationA new self-testing method of analog parts terminated by an ADC in electronic embedded systems controlled by microcontrollers is presented. It is based on a new fault diagnosis method based on on-line (i.e. during measurement), transformations of voltage samples of the time response of a tested part to a square pulse - onto localization curves placed in the measurement space. The method can be used for fault detection and single...
-
A testing method of analog parts of mixed-signal electronic systems equipped with the IEEE1149.1 test bus
PublicationA new solution of the JTAG BIST for testing analog circuits in mixed-signal electronic microsystems controlled by microcontrollers and equipped with the IEEE1149.1 bus is presented. It is based on a new fault diagnosis method in which an analog circuit is stimulated by a buffered signal from the TMS line, and the time response of the circuit to this signal is sampled by the ADC equipped with the JTAG. The method can be used for...
-
High-precision bearing estimation for active sonar with cylindrical array performed by interpolated array transformation
PublicationThe article presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. The antenna’s non-linear shape and the resulting non-uniform sampling of the signal in space, mean that known methods of high-resolution spectral analysis cannot be used. In order to apply an algorithm from this group, a linear virtual antenna must be produced. The paper presents a technique of mapping a cylindrical...
-
Deterministic and statistical size effect during shearing of granular layer within a micro-polar hypoplasticity
PublicationArtykuł omawia deterministyczny i statystyczny efekt skali w materiałach granulowanych podczas ścinania cienkiej warstwy piasku między dwoma bardzo szorstkimi ścianami. Obliczenia wykonano metodą elementów skończonych na bazie mikropolarnego prawa hipoplastycznego. Przyjęto różne metody redukujące ilość realizacji pól losowych dla początkowego wskaźnika porowatości..
-
Possibility to use engine compression ignition engines in floating power plants marine
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
The topography of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with confocal microscope
Open Research DataThe topography of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with confocal microscope.
-
Effect of temperature and ionic strength on volumetric and acoustic properties of solutions of urea alkil derivatives in aqueous NaCl
PublicationThe present work was undertaken to study volumetric and acoustic properties for diluted solutions of tetramethylurea in pure water and for urea, n-propylurea, n-butylurea and tetramethylurea in 0.5 or 1 moldm3 aqueous solutions of sodium chloride. This paper presents measured values of densities and sound velocities at T = (288.15, 298.15 and 308.15) K. From these data the apparent molar volumes, , adiabatic compressibilities,...
-
Organic Supercritical Thermodynamic Cycles with Isothermal Turbine
PublicationOrganic Rankine cycles (ORC) are quite popular, but the overall efficiencies of these plants are rather very low. Numerous studies have been conducted in many scientific centers and research centers to improve the efficiency of such cycles. The research concerns both the modification of the cycle and the increase in the parameters of the medium at the inlet to the turbine. However, the efficiency of even these modified cycles rarely...
-
Strength testing machine results
Open Research DataThe aim of the research project is to determine the rotational stiffness of the connection between the purlin and the part of the truss top chord. The attached files are referred to the forces and displacements obtained from the strength testing machine (two sensors). The 16 specimens were tested on the experimental set up.
-
Impact of Boundary Conditions on Acoustic Excitation of EntropyPerturbations in a Bounded Volume of Newtonian Gas
PublicationExcitation of the entropy mode in the field of intense sound, that is, acoustic heating, is theoreticallyconsidered in this work. The dynamic equation for an excess density which specifies the entropy mode,has been obtained by means of the method of projections. It takes the form of the diffusion equation withan acoustic driving force which is quadratically nonlinear in the leading order. The diffusion coefficient isproportional...
-
Measurement file of stainless stell shaft LSS1 and LSS2 with diameter 95,995 with 3d measurment device
Open Research Data3d point cloud consist of measured points on new stainless steel shaft used during testing hydrodynamic journal PEEK bearing.
-
Journal of Essential Oil Bearing Plants
Journals -
The morphology of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with AFM
Open Research DataThe morphology of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses was measured with the use of atomic force microscope.
-
Experimental verification of a new method of loop resistance testing in low voltage systems with residual current devices
PublicationA periodical verification of the effectiveness of protection against electric shock shall be performed in low voltage systems. The scope of this verification includes loop impedance/resistance testing. If a residual current device is installed in a tested circuit, this testing is problematic. A residual current device trips out during the test, because of the high value of measurement current. This precludes the execution of the...
-
Detailed investigation of the phase transition inKxP4W8O32and experimental arguments for a charge density wave due to hidden nesting
PublicationDetailed structural and magnetotransport properties of monophosphate tungsten bronze Kx(PO2)4(WO3)8 single crystals are reported. Both galvanomagnetic and thermal properties are shown to be consistent with a charge density wave electronic transition due to hidden nesting of the quasi-1D portion of the Fermi surface. We also observe the enhancement of electronic anisotropy due to reconstruction of the Fermi surface at the Peierls...
-
Why do patients decline amniocentesis? Analysis of factors influencing the decision to refuse invasive prenatal testing
Publication -
DSC Melting Profile of Cold-Pressed Hemp Seed Oil as an Authenticity Fingerprint Influenced by Scanning Rate
Publication -
Grating Resonances on Periodic Arrays of Sub-wavelength Wires and Strips: From Discoveries to Photonic Device Applications
Publication -
Bifurcation in von Karman problem for rectangular, thin, elastic plate resting on elastic foundation of Winkler type
PublicationPraca poświęcona jest utracie stateczności prostokątnej, cienkiej płyty sprężystej spoczywającej na podłożu liniowo sprężystym typu Winklera. Płyta jest ściskana równomiernie rozłożonymi obciążeniami na dwóch równoległych brzegach. Wyznaczono obciążenia krytyczne, formy utraty stateczności płyty oraz początkowe zachowanie pokrytyczne. Analizę prowadzono za pomocą analizy funkcjonalnej przy zachowaniu precyzyjnego matematycznego...
-
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublicationPresented in article MF seals are being researched for sea technology purposes due to their excellenttightness and low resistance of motion. These features are most valuable for ring propellers and ship'smain propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systemsare designed with contactless...
-
The meaning of cultural projects in the revitasation of urban Areas / Rola projektów kultury w rewitalizacji obszarów miejskich
PublicationArtykuł przedstawia rolę projektów kultury jako jednego z kluczowych czynników skutecznych działań rewitalizacyjnych.
-
Remote learning among students with and without reading difficulties during the initial stages of the COVID-19 pandemic
PublicationThis article presents the results of a survey on yet under-researched aspects of remote learning and learning difficulties in higher education during the initial stage (March – June 2020) of the COVID-19 pandemic. A total of 2182 students from University of Warsaw in Poland completed a two-part questionnaire regarding academic achievements in the academic year 2019/2020, living conditions and stress related to learning and pandemic,...
-
Indirect Relationship between Alcoholics Anonymous Spirituality and Their Hopelessness: The Role of Meaning in Life, Hope, and Abstinence Duration
Publication -
Synthesis and photochemical properties of unsymmetrical phthalocyanine bearing two 1-adamantylsulfanyl groups at adjacent peripheral positions
Publication -
Nanocomposites of Graphene Oxide—Silver Nanoparticles for Enhanced Antibacterial Activity: Mechanism of Action and Medical Textiles Coating
Publication -
Diagnostic testing of marine propulsion systems with internal combustion engines by means of vibration measurement and results analysis
PublicationIn this paper selected issues concerning vibration diagnosis of the mechanical system within marine propulsion units have been presented, carried out on the basis of experimental examinations of a real object in which an exceedance of the allowable vibration’s level had been observed. Used diagnosing system has been characterised. A procedure of longitudinal and transverse vibrations shaft lines of the mechanical system within...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
Proposal for calculating the bearing capacity of screw displacement piles in non-cohesive soils based on CPT results
PublicationPrzedstawienie wyników badań terenowych pali przemieszczeniowych wkręcanych, zrealizowanych w ramach projektu badawczego MNiSW. Propozycja dwóch metod obliczania nośności pali przemieszczeniowych wkręcanych w niespoistym podłożu gruntowym na podstawie wyników badań CPT. Metody dostosowano do wytycznych Eurokodu 7. Weryfikacja metod obliczeniowych z wynikami badań terenowych pali.