Search results for: anticorrosive coatings
-
Effect of microstructure on mechanical properties of BA1055 bronze castings
PublicationThe article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1032) castings used for marine propellers. Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich phase precipitates in bronze microstructure significantly affect its mechanical...
-
Wpływ zawartości grafitu na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit osadzonych na stopie AW-7075 metodą redukcji chemicznej.
PublicationPrzedstawiono wpływ obecności grafitu jako fazy dyspersyjnej na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit, które osadzono metodą redukcji chemicznej na stopie glinu AW-7075. Wykonano badania morfologii powierzchni warstw metodą mikroskopii świetlnej i skaningowej. Dalszą część pracy stanowiły badania mechaniczne, czyli pomiary mikrotwardości warstw oraz ich adhezji do aluminiowego podłoża, a także analizy wpływu...
-
Mechanical and physical assessment of epoxy, mineral, solvent-based, and water-soluble coating materials
PublicationThis paper assesses the behavior of mineral, epoxy (EP), solvent, and water-soluble coatings when exposed to salt and regular water for 28 days. Also, it evaluates the pull-off adhesion strength of the same coating materials applied to concrete slabs saturated with oil and water and dried with two different processes: air-dried for 28 days and air-dried for 14 days plus 14 days in the oven at 70 °C. Properties such as carbonation,...
-
Remote Monitoring System for Impedance Spectroscopy using Wireless Sensor Network
PublicationThe architecture of a miniaturized impedanceanalyser with wireless communication module for remoteImpedance Spectroscopy (IS) of anticorrosion coatings ondifficult-to-reach objects (e.g. on the steel construction ofthe bridge) is described in this paper. Some practical aspectsof implementation of a Wireless Sensor Network (WSN) arealso discussed. A low scale, middle range, WSN networkcomposed of a Base Station (BS) with a Personal...
-
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublicationLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
Metoda badania powłok ceramicznych w ruchu postępowo-zwrotnym = A method for testing of ceramic coatings under reciprocating sliding
PublicationOpracowano metodę badania powłok ceramicznych w warunkach tarcia ślizgowego na próbkach tworzących układ o styku niekonforemnym kula - powierzchnia płaska. Pokryte warstwą ceramiczną kule dociskano do próbek płaskich - prostopadłościennych listew (również pokrytych ceramiką), wykonujących ruch postępowo-zwrotny. Jako stanowisko badawcze zastosowano Tribometr Posuwisto-zwrotny TPZ-1. Przebieg zużywania się powłoki ceramicznej oceniano...
-
Friction and wear behaviour of self mated DLC and DLC-W coatings in water or salt in water solution lubricated sliding
PublicationPrzedstawiono wyniki badań powłok ceramicznych DLC oraz DLC z wolframem (DLC-W) nałożonych na podłoże ze stali nierdzewnej,przy tarciu ślizgowym , w modelowym skojarzeniu o styku konforemnym (płaskie czoło obracającej się względem swojej osi tulei - powierzchnia płaska). Badania prowadzono stosując smarowanie wodą destylowaną albo wodnym roztworem soli - NaCl. Wyznaczano współczynniki tarcia oraz intensywność zużywania ceramicznej...
-
Preparation and evaluation of solid-phase microextraction fibres based on functionalized latex nanoparticle coatings for trace analysis of inorganic anions
Publication -
Anisotropic optical properties of few-layer black phosphorus coatings: from fundamental insights to opto-electrochemical sensor design
PublicationFew-layer black phosphorus (FLBP) is characterised by a tuneable bandgap, high carrier mobility and anisotropic optical properties. It therefore has the potential to find applications in electronics and photonics. FLBP oxidizes upon exposure to air, limiting its utility in devices and components. To address this issue, the thesis introduces methods and tools developed for studying FLBP's optical parameters, with a particular emphasis...
-
Gelatin-chitosan interactions in edible films and coatings doped with plant extracts for biopreservation of fresh tuna fish products: A review
PublicationThe preservation of tuna fish products, which are extremely perishable seafood items, is a substantial challenge due to their instantaneous spoilage caused by microbial development and oxidative degradation. The current review explores the potential of employing chitosan-gelatin-based edible films and coatings, which are enriched with plant extracts, as a sustainable method to prolong the shelf life of tuna fish products. The article...
-
Tailoring optical constants of few-layer black phosphorus coatings: Spectroscopic ellipsometry approach supported by ab-initio simulation
Publication2D black phosphorus (BP) has attracted extensive attention as an anisotropic platform for novel optoelectronic and polarizing optics applications. Insight into the factors that tune the optical and polarizing properties of 2D BP reveals their essential influence on BP-based photonic and optoelectronic devices. In this work, studies of the optical constants of few-layer black phosphorus coatings are studied and discussed, with particular...
-
Bulk processing of ZnO nanostructures via microwave assisted oxidation of mechanically seeded Zn dust for functional paints and coatings
Publication -
The abrasive wear resistance of coatings manufactured on high-strength low-alloy (HSLA) offshore steel in wet welding conditions
PublicationSome marine and offshore structure elements exploited in the water cannot be brought to the surface of the water as this will generate high costs, and for this reason, they require in-situ repairs. One of the repair techniques used in underwater pad welding conditions is a wet welding method. This paper presents an investigation of the abrasive wear resistance of coatings made in wet welding conditions with the use of two grades...
-
Ionogel sorbent coatings for determining organophosphorus and pyrethroid insecticides in water and fresh juice samples by headspace-solid phase microextraction
PublicationThe sol–gel method yielded three different ionogel sorbent coatings that were obtained based on a silica material containing ionic liquids (ILs) immobilized in its pores. Two ILs, triethylsulfonium bis(trifluoromethylsulfonyl) imide [Set3][TFSI] and 1-butyl-1-methylpiperidinium bis(trifluoromethylsulfonyl)imide [C4C1Pip][TFSI], as well as their equimolar mixture [Set3/C4C1Pip], were used to obtain ionogel fibers. The developed...
-
The Effect of Surface Modification of Ti13Zr13Nb Alloy on Adhesion of Antibiotic and Nanosilver-Loaded Bone Cement Coatings Dedicated for Application as Spacers
PublicationSpacers, in terms of instruments used in revision surgery for the local treatment of postoperative infection, are usually made of metal rod covered by antibiotic-loaded bone cement. One of the main limitations of this temporary implant is the debonding effect of metal–bone cement interface, leading to aseptic loosening. Material selection, as well as surface treatment, should be evaluated in order to minimize the risk of fraction...
-
Low temperature deposition of dense MnCo 2 O 4 protective coatings for steel interconnects of solid oxide cells
PublicationIn this work manganese cobalt spinel (MnCo2O4) coatings were deposited on steel substrates by spray pyrolysis at 390 °C. This is at much lower temperatures than previously reported (typically in excess of 900 °C). It was possible to produce coatings with well controlled thickness (2-5-10 μm). The as-deposited coatings were evaluated for their microstructural changes and electrical conductivity up to 800 °C. Results confirm the...
-
A compact smart sensor based on a neural classifier for objects modeled by Beaunier's model
PublicationA new solution of a smart microcontroller sensor based on a simple direct sensor-microcontroller interface for technical objects modeled by two-terminal networks and by the Beaunier’s model of anticorrosion coating is proposed. The tested object is stimulated by a square pulse and its time voltage response is sampled four times by the internal ADC of microcontroller. A neural classifier based on measurement data classifies the...
-
Naval mine detection system based of FPGA circuit
PublicationElectrochemical processes take place in a metal object immersed into sea water even if an anticorrosive coating is applied [1]. As a result, flowing field appears around the object. There are naval mines between many other objects situated in the sea. Naval mines can be put in the seabed in order to be more difficult to detect by sonars. Such a mine is located on the line demarking two environments of different electrical conductivity....
-
Advanced coating of Tank Interior as means of Rising Environmental Safety of Tankers/RIM technology
Publication -
Chapter 13 : The influence of dispersion phase on composite coating properties after cold working
PublicationW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
Advanced coating of interior of tanks for rising environmental safety of tankers - novel applications of polyurethanes
PublicationOpisano technologię nanoszenia ciekłego systemu poliuretanowego na niewygrzewane elementy stalowe i stalowo-betonowe oraz sposób łączenia powłoki poliuretanowej z wymienionymi materiałami, a także między sobą przy użyciu odpowiednich środków adhezyjnych. Scharakteryzowano metodę utylizacji i odzysku polioli z zużytych w badaniach powłok poliuretanowych w recyklingu surowcowym poprzez zastosowanie małoczšsteczkowych glikoli jako...
-
The effect of the ceramic dispersion on the nickel matrix composite coating properties after plastic working
PublicationW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
Elastic protection coating for ship fuel tanks, intended for the increasing of environment protection level
PublicationW opracowaniu przedstawiono problemy związane z wprowadzeniem nowego rozwiązania dla podniesienia bezpieczeństwa zbiorników paliwowych, poprzez zainstalowanie we wnętrzu zbiornika drugiej elastycznej bariery ochronnej opartej na warstwie wypełniacza. Przedstawiono wyniki prac związanych z doborem parametrów warstwy drugiej bariery jak również materiału wypełniacza.
-
Biopolymers based paper coating with promoted grease resistivity, bio-degradable and mechanical properties
Publication -
Drug-Releasing Antibacterial Coating Made from Nano-Hydroxyapatite Using the Sonocoating Method
Publication -
Optical-Fiber Microsphere-Based Temperature Sensors with ZnO ALD Coating—Comparative Study
PublicationThis study presents the microsphere-based fiber-optic sensor with the ZnO Atomic Layer Deposition coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range from 100 °C to 300 °C, with a 10 °C step. The interferometric signal was used to monitor the integrity of the microsphere and its attachment to the connecting fiber. For the sensor...
-
The Effect of Texturing of the Surface of Concrete Substrate on the Pull-Off Strength of Epoxy Resin Coating
Publication -
Improved surface coverage of an optical fibre with nanocrystalline diamond by the application of dip-coating seeding
PublicationGrowth processes of diamond thin films on the fused silica optical fibres (10 cm in length) were investigated at various temperatures. Fused silica pre-treatment by dip-coating in a dispersion consisting of detonation nanodiamond (DND) in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) was applied. Nanocrystalline diamond (NCD) films were deposited on the fibres using the microwave plasma assisted chemical vapour deposition...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublicationElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Applications of spin coating of polymer precursor and slurrysuspensions for Solid Oxide Fuel Cell fabrication
PublicationW pracy przedstawiono możliwości zastosowania w tlenkowych ogniwach paliwowych metody nanoszenia wirowego prekursorów polimerowych i zawiesin. Przedstawiono przykłady zastosowania tej metody do wytworzenia elektrolitu oraz warstw ochronnych dla stali nierdzewnych.
-
Multispectral impedance quality testing of coil-coating system using principal component analysis
PublicationThe task of quality checking of the coil-coated system was undertaken using impedance spectroscopy. In order to properly characterize the system the new impedance spectrum was calculated as an averaged result of 12 experimental spectra obtained from 12 different places of the sample at the same time of immersion in 3% of NaCl. The experimental spectra were recorded for a 24-h period at 1 h intervals between starting points of each...
-
Damage tests of the single shell ship fuel tank with additional elastic protective coating
PublicationWejście na mieliznę lub kolizja średniej wielkości np. kontenerowca może doprowadzić do zanieczyszczenia środowiska Morza Bałtyckiego paliwem uwolnionym z rozszczelnionych, jednoposzyciowych zbiorników dennych, a ilość tego paliwa może być znaczna. W związku z tym podjęto prace badawcze zmierzające do opracowania sposobu obniżenia ryzyka rozlewu paliwa w wypadku kolizji poprzez wprowadzenie drugiej bariery ochronnej. Idea pomysłu...
-
Evaluation of organic coating systems for corrosion protection of industrial equipment using impedance spectroscopy
PublicationThe high economic impact of corrosion can be reduced by enhanced corrosion management and prevention based on appropriate means. This applies in particular to the protection of structures with organic protective coatings. Steel is subject to corrosion that reduces its service life and leads to destruction in most severe cases. The application of paints to metallic objects for corrosion control has been known for a long time and...
-
Functional fluorine-doped tin oxide coating for opto-electrochemical label-free biosensors
PublicationSensors operating in multiple domains, such as optical and electrochemical, offer properties making biosensing more effective than those working in a single domain. To combine such domains in one sensing device, materials offering a certain set of properties are required. Fluorine-doped tin oxide (FTO) thin film is discussed in this work as functional optically for guiding lossy modes and simultaneously electrochemically, i.e....
-
Drop-coating deposition surface-enhanced Raman spectroscopy on silver substrates for biofluid analysis
PublicationUtilization of surface-enhanced Raman spectroscopy as a measurement technique is of particular interest in biodetection due to its superb chemical specificity and high sensitivity. The use of SERS substrates further improve this method by massive enhancement of the molecule Raman spectrum, permitting very low levels of detection. Therefore it is important to seek for new ways to develop reliable substrates, which are quickly and...
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublicationPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
Using impedance spectroscopy to characterize and monitor protection aspects of organic coating systems on metal
PublicationOrganiczne powłoki ochronne stosowane są powszechnie do ochrony konstrukcji metalowych przed korozją i zużyciem mechanicznym. W pracy zaproponowano nowy typ sensora impedancyjnego, który może być zastosowany do ciągłej oceny właściwości barierowych i adhezyjnych systemów powłokowych w warunkach terenowych w sposób nieniszczący, bez konieczności stosowania naczyń z elektrolitem. Przedstawiono koncepcję czujnika oraz przykładowe...
-
Silica-Based Ionogels: Nanoconfined Ionic Liquid-Rich Fibers for Headspace Solid-Phase Microextraction Coupled with Gas Chromatography–Barrier Discharge Ionization Detection
PublicationIn this work, hybrid silica-based materials with immobilized ionic liquids (ILs) were prepared by sol–gel technology and evaluated as solid-phase microextraction (SPME) fiber coatings. High loadings of the IL 1-methyl-3-butylimidazolium bis(trifluoromethylsulfonyl)imide ([C4MIM][TFSI]) were confined within the hybrid network. Coatings composition and morphology were evaluated using scanning electron microscopy and energy dispersive...
-
Raman spectroscopy analysis of synthesized sol-gel silica coatings
Open Research DataThese data contains Raman spectra of silica coatings synthesized using sol-gel method A and B, which were described with publication associated with this dataset. Raman scattering was measured with a Renishaw microRaman spectrometer (830 nm).
-
SEM micrographs of the topography of Cu-Sn-TiO2 nanocomposite coatings
Open Research DataThe dataset contains the scanning electron microscopy (SEM) micrographs of nanocomposite Cu-Sn-TiO2 coatings electrodeposited from oxalic acid bath containing Cu and Sn salts as well as TiO2 nanoparticles under various treatments: mechanical stirring, ultrasonic or none. The details of the electrodeposition process are presented in the readme file attached...
-
Imaging and chemical investigation of silver coating
Open Research DataThe recovery of silver from materials such as plates, still used in clinical radiography [1], or scrap jewelery is still very popular. The subject of the research, part of which was microscopic imaging, was to recreate the behavior of an electrochemically deposited silver coating. The copper electrodes were covered with a layer of silver obtained from...
-
Method of managing drill cuttings from shale gas formations
PublicationProposed management method of drill cuttings involves recycling for the expanded clay production. A theoretical presentation of the possibility, choosing planning path based on similarity between the materials used in the manufacture of expanded clay and oily cuttings. Application for the main stages of manufacture of expanded clay production of drill cuttings from shale gas extraction. Introduced into circulation solid waste partly...
-
On bounded load routings for modeling k-regular connection topologies
PublicationW pracy analizowane są problemy modelowania k-regularnych topologii sieci komputerowych z punktu widzenia routingu typu point-to-point. Zaprezentowane są algorytmy oraz przeprowadzona jest analiza złożoności obliczeniowej.
-
Effect of the Unit Pressure on the Selection Parameters of Intermetallic Coastings NiAl and Ni3Al after Platic Working
PublicationW artykule omówiono wpływ zgniotu na wybrane parametry warstwy międzymetalicznej NiAl i Ni3Al napawanej na stali C45 podanej obróbce plastycznej poprzez prasowanie na zimno.
-
Fuzzy reasoning approach to properties' determination of calcium phosphate coatings processed using ion beam assisted deposition on heated substrates
PublicationPraca przedstawia rozmyty system wnioskowania dla zamodelowania związków pomiędzy temperaturą podłoża oraz stosunkiem molowym Ca/P w gradientowej powłoce hydroxyapatytowej na podłożu tytanowym. Przeprowadzono symulację działania sterownika rozmytego na pomocą oprogramowania Matlab.
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublicationThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
Artificial neural network model of hardness, porosity and cavitation erosion wear of APS deposited Al2O3 -13 wt% TiO2 coatings
Publication -
The Use of Cluster Analysis to Assess the Wear Resistance of Cermet Coatings Sprayed by High Velocity Oxy-Fuel on Magnesium Alloy Substrate
PublicationCermet coatings are one of the best surface protection of machine elements against wear. On the other hand, the most universal and economically justified method of applying such coatings is high velocity oxy-fuel (HVOF) spraying. This method makes it possible to produce coatings characterized by compact structure, low porosity and very good adhesion to the substrate. All these fundamental properties contribute to the high wear...
-
Osteoblast and bacterial cell response on RGD peptide‐functionalized chitosan coatings electrophoretically deposited from different suspensions on Ti13Nb13Zr alloy
PublicationMetallic materials for long-term load-bearing implants still do not provide high antimicrobial activity while maintaining strong compatibility with bone cells. This study aimed to modify the surface of Ti13Nb13Zr alloy by electrophoretic deposition of a chitosan coating with a covalently attached Arg-Gly-Asp (RGD) peptide. The suspensions for coating deposition were prepared in two different ways either using hydroxyacetic acid...
-
Solid State Conductivity of Optimized Polypyrrole Coatings on Iron Obtained from Aqueous Sodium Salicylate Solution Determined by Impedance Spectroscopy
PublicationIn this work the optimization procedure for corrosion resistance, surface analysis and electrical properties of PPy-Fe electrodes have been examined. Polypyrrole (PPy) film was electrochemically synthesized in a one step process from an aqueous solution of sodium salicylate and pyrrole with certain concentrations, different parameters and type of polymerization...