Filtry
wszystkich: 2535
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MULTI-FIDELITY MODELING
-
Modeling of Ice Passage Through Reservoirs System on the Vistula River
PublikacjaNumerical model was used to assess ice passage through proposed reservoir on the lower Vistula River. Model results were compared with observation on the Vistula River, but because the dam is not constructed yet, the direct comparison was not possible. The study focused on ice movement and accumulation in the reservoir for variety of low flow condition with and without wind effect. Bridge’s piers in the upper part of the reservoir...
-
Analytical modeling of electric drives for vehicle traction control systems
PublikacjaWheel-torque control bandwidth in vehicle dynamics model is crucial in evaluating optimal tracking ability of tire slip and in analysis of control system stability. Electric drives’ control dynamics are influenced by timing of digital control events, e.g. by sampling instant of motor currents. Reflecting this timing in drive analytical models is therefore important for analysis of vehicle traction systems. The paper considers five...
-
Assessment of chemical‐crosslink‐assisted protein structure modeling in CASP13
Publikacja -
Modeling of Wireless Traffic Load in Next Generation Wireless Networks
Publikacja -
FEM modeling of structures based on close range digital photogrammetry
PublikacjaPraca dotyczy metodologii przygotowania modelu konstrukcji istniejącej do analizy mechanicznej metodą element ow skończonych. MOdelowanie geometrii budowli jest oparte na danych pozyskanych z pomiarów fotogrametrycznych. Praca wskazuje na możliwości oraz efektywność zastosowania metod optometrycznych w rewitalizacji budowli zabytkowych, an przykładzie modelu dachu drewnianego.
-
Temperature-dependent structure-property modeling of viscosity for ionic liquids
PublikacjaIn this paper we present the methodology for assessing the ionic liquids' viscosity at six temperature points (25, 35, 45, 50, 60 and 70 [C]), which utilizes only the in silico approach. The main idea of such assessment is based on the "correction equation" describing the correlation between experimentally measured viscosity and theoretically derived density (calculated with use of molecular mechanics), given at 6 different temperature...
-
Modeling of a Combined Cycle Gas Turbine Integrated with an Adsorption Chiller
Publikacja -
Modeling of lapping plate wear and conditioning in single-sided lapping
PublikacjaIn order to achieve higher quality on worked surfaces with lower roughness, very high accuracy of shape and dimensions it is crucial to improve conventional finishing technologies and to develop new working principles. Single-sided lapping is one of the most effective planarization technologies and it is determined by a number of factors and boundary conditions. The most significant influence over a dimensional and profile accuracy,...
-
POM/EVA Blends with Future Utility in Fused Deposition Modeling
PublikacjaPolyoxymethylene (POM) is one of the most popular thermoplastic polymers used in the industry. Therefore, the interest in its potential applications in rapid prototyping is understandable. Nevertheless, its low dimensional stability causes the warping of 3D prints, limiting its applications. This research aimed to evaluate the effects of POM modification with ethylene-vinyl acetate (EVA) (2.5, 5.0, and 7.5 wt.%) on its processing...
-
Modeling the Structure, Dynamics, and Transformations of Proteins with the UNRES Force Field
PublikacjaThe physics-based united-residue (UNRES) model of proteins ( www.unres.pl ) has been designed to carry out large-scale simulations of protein folding. The force field has been derived and parameterized based on the principles of statistical-mechanics, which makes it independent of structural databases and applicable to treat nonstandard situations such as, proteins that contain D-amino-acid residues. Powered by Langevin dynamics...
-
Mispronunciation Detection in Non-Native (L2) English with Uncertainty Modeling
PublikacjaA common approach to the automatic detection of mispronunciation in language learning is to recognize the phonemes produced by a student and compare it to the expected pronunciation of a native speaker. This approach makes two simplifying assumptions: a) phonemes can be recognized from speech with high accuracy, b) there is a single correct way for a sentence to be pronounced. These assumptions do not always hold, which can result...
-
Modeling SARS‐CoV‐2 proteins in the CASP‐commons experiment
PublikacjaCritical Assessment of Structure Prediction (CASP) is an organization aimed at advancing the state of the art in computing protein structure from sequence. In the spring of 2020, CASP launched a community project to compute the structures of the most structurally challenging proteins coded for in the SARS-CoV-2 genome. Forty-seven research groups submitted over 3000 three-dimensional models and 700 sets of accuracy estimates on...
-
Mainstream shortcut N removal modeling current status and perspectives
PublikacjaThis work gives an overview of the state-of-the-art in modelling of short-cut processes for nitrogen removal in mainstream wastewater treatment and presents future perspectives for directing research efforts in line with the needs of practice. The modelling status for deammonification (i.e., anammox-based) and nitrite-shunt processes is presented with its challenges and limitations. The importance of mathematical models for considering...
-
Systems, Environments, and Soliton Rate Equations: Toward Realistic Modeling
PublikacjaIn order to solve a system of nonlinear rate equations one can try to use some soliton methods. The procedure involves three steps: (1) find a ‘Lax representation’ where all the kinetic variables are combined into a single matrix ρ, all the kinetic constants are encoded in a matrix H; (2) find a Darboux–Bäcklund dressing transformation for the Lax representation iρ˙=[H,f(ρ)], where f models a time-dependent environment; (3) find...
-
SIMPLIFIED MODELING OF STRESS AND DEFLECTION LIMIT STATES OF UNDERGROUND TANKS
PublikacjaFuel tanks are designed with regard to standard actions and operating conditions. The work analyses the impact of corrosion and other means to variation of stresses and deformation of a horizontal underground tank shell. The computations are preliminary. Due to the long computational time of the entire tank the analysis is restricted to its part only. The full analysis is bound to assess structural reliability, further allowing...
-
Comparative modeling of shear localization in granular bodies with FEM and DEM
PublikacjaThe intention of the paper is to compare the calculations of shear zones in granular bodies using two different approaches: a continuum and a discrete one. In the first case, the FEM based on a micro-polar hypoplastic constitutive law was used. In the second case, the DEM was taken advantage of, where contact moments were taken into account to model grain roughness. The comparative calculations were performed for a passive case...
-
Modeling of the behavior of granular bodies using DEM with contact moments
PublikacjaW artykule przedstawiono wyniki symulacji badania trójosiowego dla materiałów granulowanych. Obliczenia wykonano przy zastosowaniu metody DEM. Pokazano wpływ momentów kontaktowych na wytrzymałość próbki. Zbadano wpływ parametrów mikroskopowych.
-
Numerical modeling of shear localizations during granular flow in silos.
PublikacjaW artykule przedstawiono wyniki numerycznej analizy MES dotyczącej przepływów materiałów sypkich w silosach. Omówiono różne metody opisu lokalizacji odkształceń stycznych wewnątrz materiałów. Wyniki porónano z wynikami doświadczalnymi.
-
On Computationally-Efficient Reference Design Acquisition for Reduced-Cost Constrained Modeling and Re-Design of Compact Microwave Passives
PublikacjaFull-wave electromagnetic (EM) analysis has been playing a major role in the design of microwave components for the last few decades. In particular, EM tools allow for accurate evaluation of electrical performance of miniaturized structures where strong cross-coupling effects cannot be adequately quantified using equivalent network models. However, EM-based design procedures (parametric optimization, statistical analysis) generate...
-
Modeling and simulation of blood flow under the influence of radioactive materials having slip with MHD and nonlinear mixed convection
PublikacjaRadioactive materials are widely in industry, nuclear plants and medical treatments. Scientists and workers in these fields are mostly exposed to such materials, and adverse effects on blood and temperature profiles are observed. In this regard, objective of the current study is to model and simulate blood based nanofluid with three very important radioactive materials, named as Uranium dioxide (UO2), Thorium dioxide (ThO2) and...
-
Effective Permeability of Multi Air Gap Ferrite Core 3-Phase Medium Frequency Transformer in Isolated DC-DC Converters
PublikacjaThe magnetizing inductance of the medium frequency transformer (MFT) impacts the performance of the isolated dc-dc power converters. The ferrite material is considered for high power transformers but it requires an assembly of type “I” cores resulting in a multi air gap structure of the magnetic core. The authors claim that the multiple air gaps are randomly distributed and that the average air gap length is unpredictable at the...
-
warsztaty dotyczące tematyki „Multi-Paradigm Modelling for Cyber-Physical Systems”
WydarzeniaKomitet Zarządzający Europejskiej Akcji COST (http://www.cost.eu) IC-1404 Multi-Paradigm Modelling for Cyber-Physical Systems (MPM4CPS; www.cost.eu/COST_Actions/ict/IC1404); Oddział Mazowiecki PTI oraz Polski Oddział IEEE Computer Society zapraszają na warsztaty dotyczące tematyki "Multi-Paradigm Modelling for Cyber-Physical Systems"; miejsce: Wydział...
-
Towards an efficient multi-stage Riemann solver for nuclear physics simulations
PublikacjaRelativistic numerical hydrodynamics is an important tool in high energy nuclear science. However, such simulations are extremely demanding in terms of computing power. This paper focuses on improving the speed of solving the Riemann problem with the MUSTA-FORCE algorithm by employing the CUDA parallel programming model. We also propose a new approach to 3D finite difference algorithms, which employ a GPU that uses surface memory....
-
The use of numerical methods for the analysis of phase phenomena in multi element antennas.
PublikacjaW artykule zostały zaprezentowane wyniki analizy wpływu wzajemnej i własnej impedancji promieniowania na fazę sygnału odbieranego przez antenę wieloelementową. Obliczenia dokonano dla elektrycznego modelu zastępczego Mason`a przetwornika ultradźwiękowego.
-
Compact scheduling of zero-one time operations in multi-stage systems.
PublikacjaRozważamy szeregowanie zwarte na maszynach dedykowanych z zero-jedynkowymi operacjami w modelu otwartym, przepływowym i mieszanym. Harmonogramy zostały zmodelowane przy pomocy pokolorowań krawędzi grafu konfliktów z pewnymi dodatkowymi ograniczeniami. Dowodzimy NP-trudności problemów w przypadku ogólnym oraz prezentujemy przegląd znanych wielomianowych algorytmów szeregujących dla systemów o specyficznej budowie.
-
Fixed point theorems for weakly commuting and compatible multi-valued mappings.
PublikacjaW pracy podano twierdzenia o wspólnych punktach stałych czwórki odwzorowań: dwóch jednowartościowych T i S oraz dwóch wielowartościowych F i G, spełniających nieliniowy uogólniony warunek kontrakcyjny, przy pewnych założeniach dotyczących uogólnionej komutatywności T,S i F,G. W pracy zamieszczono przykłady ilustrujące udowodnione twierdzenia.
-
Compact scheduling of zero–one time operations in multi-stage systems
Publikacja -
POPULATION-BASED MULTI-AGENT APPROACH TO SOLVING MACHINE LEARNING PROBLEMS
Publikacja -
Dynamical processes in a multi-motor gear drive of heavy slabbing mill
Publikacja -
Rip currents in the southern Baltic Sea multi-bar nearshore zone
Publikacja -
An application of the TCRBF neural network in multi-node fault diagnosis method
PublikacjaPrzedstawiono nową metodę samo-testowania części analogowej w systemach elektronicznych sterowanych mikrokontrolerami. Układ badany pobudzany jest przebiegiem sinusoidalnym przez generator zamontowany w systemie, a jego odpowiedź jest próbkowana w wybranych węzłach przez wewnętrzny przetwornik A/C mikrokontrolera. Detekcja i lokalizacja uszkodzenia jest dokontwana przez sieć neuronową typu TCRBF. Procedurę diagnostyczną zaimplementowano...
-
Bilateral Multi-Issue Negotiation Between Active Documents and Execution Devices
PublikacjaMobile document-agents are often in conflict with execution devices when attempting to perform activities of the business process they implement, since preferences of device owners may change depending on their current location and the actual class of the device in use. The paper proposes a bilateral negotiation mechanism based on a simple bargaining game that can effectively resolve such conflicts without any third party support.
-
A study of rigorous ODE integrators for multi-scale set-oriented computations
Publikacja -
Middle Eastern Christian Spaces in Europe: Multi-sited and Super-diverse
Publikacja -
Analysis of electrical patterns activity in artificial multi-stable neural networks
Publikacja -
Multi-Criteria Early Warning System Against Enteprise Bankruptcy Risk
PublikacjaW artykule tym autor porównuje skuteczność opracowanego przez niego wielokryterialnego systemu wczesnego ostrzegania firm z tradycyjnym modelem analizy dyskryminacyjnej prognozowania upadłości. System wczesnego ostrzegania oparty został na metodzie logiki rozmytej. Badania te są jedną z pierwszych prób na świecie wykorzystania logiki rozmytej w prognozowaniu zagrożenia bankructwem firm. Uzyskane wyniki świadczą o dużym potencjale...
-
Solving Multi-Ship Encounter Situations by Evolutionary Sets of Cooperating Trajectories
PublikacjaAutor zaproponował nowe podejście do sytuacji kolizyjnych na morzu. Polega ono na zastąpieniu ewolucyjnej trajektorii własnej ewolucyjnym zbiorem trajektorii wszystkich obiektów. Podejście to umożliwia predykcję manewrowania obiektów obcych przy jednoczesnym zachowaniu efektywności algorytmów ewolucyjnych. Dodatkowo, opracowany już wstępnie przez autorów zbiór kryteriów, ograniczeń i operatorów specjalizowanych powinien zapewnić...
-
Ad Hoc Multi-WLAN: A Game-Theoretic Model of Correlated Play
PublikacjaZakładając pewien rozkład prawdopodobieństwa długości sesji danych, scharakteryzowano punkt równowagi korelowanej w przypadku wielodostępu w sieci bezprzewodowej z wieloma sieciami lokalnymi i dokonano porównania wydajności z punktem równowagi mieszanej dla różnych liczb terminali.
-
Multi-Option Model of Railway Traffic Organization Including the Energy Recuperation
PublikacjaThe article presents the issue of organization of railway traffic within the station, taking into account energy recuperation. We identified a number of factors which affect the energy efficiency of recuperation, including the issue of transfer of energy technology between a few vehicles. We presented some aspects of the decision problem of graphic train timetable construction with regard to recuperation. As an indicator of quality...
-
Bilateral multi-issue negotiation of execution contexts by proactive document agents
PublikacjaA proactive document can react to its actual environment by autonomously selecting and performing actions integrated into its body and interact with its user. When migrating over a network of execution devices it may encounter diverse execution contexts, each one set up according to temporal characteristics of a receiving device and preferences of its owner. A concept to augment proactive documents with negotiation capability is...
-
Multi‐wall carbon nanotubes – a vehicle for targeted Irinotecan drug delivery
Publikacja -
Application of multi-criteria mathematical programming models for assignment of services in a hospital
Publikacja -
Survey of multi-objective portfolio optimization by linear and mixed integer programming
Publikacja -
A Multi-Antenna Scheme for Early Detection and Mitigation of Intermediate GNSS Spoofing
PublikacjaThis article presents a method for detecting and mitigating intermediate GNSS spoofing. In this type of attack, at its early stage, a spoofer transmits counterfeit signals which have slight time offsets compared to true signals arriving from satellites. The anti-spoofing method proposed in this article fuses antenna array processing techniques with a multipath detection algorithm. The latter is necessary to separate highly correlated...
-
Mitigating Traffic Remapping Attacks in Autonomous Multi-hop Wireless Networks
PublikacjaMultihop wireless networks with autonomous nodes are susceptible to selfish traffic remapping attacks (TRAs). Nodes launching TRAs leverage the underlying channel access function to receive an unduly high Quality of Service (QoS) for packet flows traversing source-to-destination routes. TRAs are easy to execute, impossible to prevent, difficult to detect, and harmful to the QoS of honest nodes. Recognizing the need for providing...
-
A city is not a tree: a multi-city study on street network and urban life
PublikacjaChristopher Alexander, a British-American scholar, differentiated an old (natural) city from a new (planned) one by structure. The former resembles a “semilattice”, or a complex system encompassing many interconnected sub-systems. The latter is shaped in a graph-theoretical “tree”, which lacks the structural complexity as its sub-systems are compartmentalized into a single hierarchy. This structural distinction explains why, or...
-
Multi-scale modelling of concrete beams subjected to three-point bending
PublikacjaW artykule przedstawiono wyniki numeryczne MES dwuskalowego modelowania belek betonowych z nacięciem na poziomie skali makro i mezo. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Natomiast na poziomie skali makro został opisany jako materiał...
-
Modeling Earth Systems and Environment
Czasopisma -
Sławomir Jerzy Ambroziak dr hab. inż.
OsobySławomir J. Ambroziak urodził się w 1982 r. Uzyskał tytuł zawodowy magistra inżyniera w zakresie systemów i usług radiokomunikacyjnych w roku 2008, w 2013 r. uzyskał stopień doktora nauk technicznych w dyscyplinie telekomunikacja, w specjalności radiokomunikacja, natomiast w 2020 r. uzyskał stopień doktora habilitowanego. Od 2008 r. jest pracownikiem Katedry Systemów i Sieci Radiokomunikacyjnych na Wydziale Elektroniki, Telekomunikacji...
-
Modeling of TEC Variations Based on Signals from Near Zenith GNSS Satellite Observed by Dense Regional Network
PublikacjaCurrently the substantial successes in high-resolution ionospheric mapping is declared in many publications. Nevertheless, up to now there are no examples of dynamic visualization of TEC disturbances on regional scale with as high resolution as tropospheric models. Over the years, ionosphere has been modeling basing on the simple assumption, that it is a thin layer, which surrounds the Earth at some arbitrary height. However, the...
-
The evaluation of COD fractionation and modeling as a key factor for appropriate optimization and monitoring of modern cost-effective activated sludge systems
PublikacjaA study was conducted to characterize the raw wastewater entering a modern cost effective municipal WWTP in Poland using two approaches; 1) a combination of modeling and carbonaceous oxygen demand (COD) fractionation using respirometric test coupled with model estimation (RTME) and 2) flocculation/filtration COD fractionation method combined with BOD measurements (FF-BOD). It was observed that the particulate fractions of COD obtained...
-
Bandwidth-size design trade-offs for compact spline-parameterised patch couplers by means of electromagnetic-driven multi-objective optimisation
PublikacjaBroad bandwidth and small size are the key performance figures for contemporary microwave couplers. These requirements are conflicting, i.e. improvement of one generally leads to degradation of the other assuming fixed topology of the circuit at hand. From a designer's perspective, the knowledge about available design trade-offs is indispensable as it permits for tailoring the circuit for particular applications as well as comparing...
-
Mathematical modeling and prediction of pit to crack transition under cyclic thermal load using artificial neural network
PublikacjaThe formation of pitting is a major problem in most metals, which is caused by extremely localized corrosion that creates small holes in metal and subsequently, it changes into cracks under mechanical load, thermo-mechanical stress, and corrosion process factors. This research aims to study pit to crack transition phenomenon of steel boiler heat tubes under cyclic thermal load, and mathematical modeling...
-
Geometry Modeling and Processing
Konferencje -
Estimation of groundwater recharge in a shallow sandy aquifer using unsaturated zone modeling and water table fluctuation method
PublikacjaQuantification of groundwater recharge is one of the most important issues in hydrogeology, especially in view of the ongoing changes in climate and land use. In this study, we use numerical models of 1D vertical flow in the vadose zone and the water table fluctuation (WTF) analysis to investigate local-scale recharge of a shallow sandy aquifer in the Brda outwash plain in northern Poland. We show that these two methods can be...
-
ACM Transactions on Modeling and Performance Evaluation of Computing Systems
Czasopisma -
Energy Systems-Optimization Modeling Simulation and Economic Aspects
Czasopisma -
Metabolic activity of tree saps of different origin towards cultured human cells in the light of grade correspondence analysis and multiple regression modeling
PublikacjaTree saps are nourishing biological media commonly used for beverage and syrup production. Although the nutritional aspect of tree saps is widely acknowledged, the exact relationship between the sap composition, origin, and effect on the metabolic rate of human cells is still elusive. Thus, we collected saps from seven different tree species and conducted composition-activity analysis. Saps from trees of Betulaceae, but not from...
-
Applications of the artificial intelligence methods for modeling of the ACAlSi7Cu alloy crystallization process
Publikacja -
High-resolution microscopy assisted mechanical modeling of ultrafine electrospun network
Publikacja -
Ultracapacitor modeling and control with discrete fractional order artificial neural network
Publikacja -
Modeling of CO Accumulation in the Headspace of the Bioreactor during Organic Waste Composting
Publikacja -
Cross-talk modeling in coupled transmission lines terminated with nonlinear loads
PublikacjaW pracy przedstawiono przegląd dostępnych metod symulacji zjawiska przesłuchu kładąc szczegółny nacisk na efekty nieliniowości rzeczywistych obciążeń linii sygnałowych na płytach drukowanych. Wykorzystując metodę analizy opartą o szeregi Volterry przeanalizowano efekt przesłuchu w strukturze sprzężonych linii mikropaskowych obciążonych na wyjściu toru transmisyjnego diodą Schottky'ego z niską barierą potencjalu. Uzyskano bardzo...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublikacjaIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...
-
Mathematical Modeling of Ice Dynamics as a Decision Support Tool in River Engineering
PublikacjaThe prediction of winter flooding is a complicated task since it is affected by many meteorological and hydraulic factors. Typically, information on river ice conditions is based on historical observations, which are usually incomplete. Recently, data have been supplemented by information extracted from satellite images. All the above mentioned factors provide a good background of the characteristics of ice processes, but are not...
-
Selected aspects of customization of cognitive dimensions for evaluation of visual modeling languages.
PublikacjaFor the successful application of diagrams in software engineering, high quality visual modelling languages (VML) are required. There is a need for new effective methodologies of VML evaluation. This paper discusses selected aspects of applying cognitive dimensions as a basis of the evaluation. Then, it briefly presents CD-VML methodology which integrates the cognitive dimensions with a theory of visual modelling languages. Finally,...
-
Modeling incipient creep damage effects on Barkhausen noise and magnetoacoustic emission.
PublikacjaZaproponowano model fizyczny opisujący zmiany natężenia efektu Barkhausena i emisji magnetoakustycznej podczas procesu degradacji stali ekploatowanych w przemyśle energetycznym.
-
Modeling of unsaturated water flow in double-porosity soils by the homogenization approach.
PublikacjaGrunty o podwójnej porowatości zbudowane są z dwóch materiałów o znacznie różniących się parametrach hydraulicznych. Ze względu na tą szczególną strukturę, podczas przepływu nieustalonego w tego typu gruntach wytwarzają się lokalne różnice ciśnienia kapilarnego. W artykule przedstawiono model przepływu w gruntach o podwójnej porowatości w skali makroskopowej z uwzględnieniem efektów lokalnych. Model otrzymano metodą homogenizacji....
-
The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling
PublikacjaThis paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...
-
Stress Relaxation Behaviour Modeling in Rigid Polyurethane (PU) Elastomeric Materials
PublikacjaPolyurethane (PU) has been used in a variety of industries during the past few years due to its exceptional qualities, including strong mechanical strength, good abrasion resistance, toughness, low-temperature flexibility, etc. More specifically, PU is easily “tailored” to satisfy particular requirements. There is a lot of potential for its use in broader applications due to this structure–property link. Ordinary polyurethane items...
-
Monte-Carlo Modeling of Optical Sensors for Postoperative Free Flap Monitoring
PublikacjaThis work aims to develop a numerical tissue model and implement software to simulate photon propagation using the Monte Carlo method to determine design guidelines for a physical measurement system. C++ was used for the simulation program, and Python as a programming environment to create an interface that allows the user to customize individual simulation elements, allowing for increased accuracy and flexibility when simulating...
-
5G/6G optical fronthaul modeling: cost and energy consumption assessment
PublikacjaIn fifth generation (5G) and the future beyond 5G (6G) radio access networks (RANs), the cost of fronthaul deployment is a main challenge for mobile network operators. Depending on different constraints, there are various solutions to deploy an efficient fronthaul. Fiber-optic-based fronthaul offers long-term support with regard to a rapid increase in capacity demands. When fiber connections, either point-to-point (P2P) or point-to-multipoint...
-
Efficient modeling of the time-domain crosstalk phenomena in coupled microstrip lines
PublikacjaW pracy przedstawiono efektywną technikę analizy zjawiska przesłuchu w sprzężonych liniach mikropaskowych. Analiza uwzględnia hybrydową naturę prowadzonych fal i prowadzi do określenia postaci czasowych sygnałów na zaciskach struktury w zależności od parametrów układu linii sprzężonych oraz własności obciążeń. Wyniki analizy zweryfikowano poprzez porównanie z wynikami badań eksperymentalnych, uzyskując bardzo dobrą zgodność.
-
Accidental wow evaluation based on sinusoidal modeling and neural nets prediction
PublikacjaReferat przedstawia opis algorytmu do określenia charakterystyki zniekształcenia kołysania dźwięku. Prezentowane podejście wykorzystuje sinusoidalną analizę dźwięku bazującą zarówno na amplitudowym jak i fazowym widmie sygnału fonicznego. Trajektorie poszczególnych składowych tonalnych, obrazujące zniekształcenie kołysania, określane są na podstawie analizy ich chwilowych amplitud, częstotliwości i faz. Dodatkowo referat przedstawia...
-
Process modeling inside cylinder in an internal combustion engine with heat regeneration
Publikacja -
Fourth International Workshop on Reliable Networks Design and Modeling (RNDM 2012)
Publikacjaartykuł sprawozdawczy z konferencji
-
Designing drainage systems – possible application of advanced calculations and hydrodynamical modeling
PublikacjaNowadays we can observe a faster development of drainage systems than ever. This gives us an opportunity to de- sign more efficient systems that can cope with the rapid growth of cities and, what comes with it, impervious surfaces. Here the question arises, whether traditional methods used in drainage system design are potent enough to cope with the emerging prob- lems and difficulties. In this paper we will make...
-
Numerical single-phase modeling of turbulent flow and heat transfer of nanofluids
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000< Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with published experimental data.
-
Thermal ablation modeling via the bioheat equation and its numerical treatment
PublikacjaThe phenomenon of thermal ablation is described by Pennes’ bioheat equation. This model is based on Newton’s law of cooling. Many approximate methods have been considered because of the importance of this issue. We propose an implicit numerical scheme which has better stability properties than other approaches.
-
Performance Modeling and Prediction of Real Application Workload in a Volunteer-based System
PublikacjaThe goal of this paper is to present a model that predicts the real workload placed on a volunteer based system by an application, with incorporation of not only performance but also availability of volunteers. The application consists of multiple data packets that need to be processed. Knowing the computational workload demand of a single data packet we show how to estimate the application workload in a volunteer based system. Furthermore,...
-
Application of Capillary Polypropylene Membranes for Microfiltration of Oily Wastewaters: Experiments and Modeling
Publikacja -
Two dimensional modeling of the flood zones in the Vistula river valley in Warsaw
PublikacjaPrzedstawiono metodę numerycznego wyznaczania stref zagrożenia powodziowego. Transformację fali powodziowej symulowano, używając dwuwymiarowych równań de Saint-Venanta. Zasięg zalewu i strefy zagrożenia powodziowego przedstawiono w systemie GIS. Wykonano analizę zagrożenia powodziowego w dolinie Wisły w Warszawie.
-
Noise modeling of static CMOS gates for low-noise circuit synthesis
PublikacjaW artykule przedstawiono efektywną metodę modelowania widma szumu napięcia zasilającego generowanego przez statyczne bramki cyfrowe CMOS. Metoda modelowania uwzględnia krótkie impulsy prądowe powstające w czasie przełączania bramek i pozwala oszacować górne limity widma szumu napięcia zasilającego co umożliwia niskoszumową syntezę układów cyfrowych.
-
OmicSelector: automatic feature selection and deep learning modeling for omic experiments
Publikacja -
Monte-Carlo Modeling of Optical Sensors for Postoperative Free Flap Monitoring
PublikacjaThis work aims to develop a numerical tissue model and implement software to simulate photon propagation using the Monte Carlo method to determine design guidelines for a physical measurement system. C++ was used for the simulation program, and Python as a programming environment to create an interface that allows the user to customize individual simulation elements, allowing for increased accuracy and flexibility when simulating...
-
Improving peak detection by Gaussian mixture modeling of mass spectral signal
Publikacja -
Probabilistic approach of the Upper and Middle Odra basin daily rainfall modeling
Publikacja -
3rd International Workshop on Reliable Networks Design and Modeling (RNDM 2011)
Publikacjaartykuł sprawozdawczy z konferencji
-
Mathematical Modeling of Dissolved Matter Transport with Biodegradation in Activated-Sludge Systems
PublikacjaW pracy przedstawiono problem matematycznego modelowania transportu substancji rozpuszczonej z biodegradacją w systemach z osadem czynnym. Przedstawione zostały główne równania opisujące proces transportu adwekcyjno-dyspersyjnego wraz z modelem biokinetycznym ASM2d, opisującym procesy przemian pod wpływem osadu czynnego. W artykule przedstawiono wyniki symulacji numerycznych odtwarzających testy laboratoryjne przeprowadzone w nieprzepływowych...
-
1+1 Protection of Overlay Distributed Computing Systems: Modeling and Optimization
PublikacjaW niniejszym artykule przedstawiono autorską koncepcję ochrony transmisji od krańca do krańca (ang. 1+1 protection) dla systemów przetwarzania rozproszonego (ang. distributed computing systems). Artykuł prezentuje nowatorskie rozwiązanie dedykowane systemom typu ''overlay'', w których system przetwarzania rozproszonego stanowi warstwę najwyższą w warstwowej architekturze sieci, korzystającą z usług warstwy sieci transportowej....
-
Remarks on steam condensation modeling related to steam turbine large output
PublikacjaIn the paper numerical simulations have been performed to predict the performance of the diferent steam models. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine equipped with the so-called Baumann stage. For numerical analysis three models have been finally used - the ideal steam model without...
-
Experiments and numerical modeling of meat and bone meal pyrolysis in a rotary kiln
PublikacjaThe paper presents aspects of modelling the pyrolysis of meat and bone meal (MBM) in a rotary kiln. The pyrolysis of MBM produces a solid fraction which can be used as a fuel, a liquid fraction with potential chemical applications and a low heating value gas. The meat and bone meal pyrolysis was carried out at the temperature of 900 oC. Main features of experiments and numerical model of the pyrolysis were described. The model...
-
Modeling of natural convection with Smoothed Particle Hydrodynamics: Non-Boussinesq formulation
Publikacja -
Modeling of the finite amplitude plane wave propagation in non-dissipative medium
PublikacjaPraca prezentuje wyniki analizy teoretycznej zagadnienia propagacji fali płaskiej o skończonej amplitudzie w ośrodku wodnym bez dyssypacji. Przedstawiono model matematyczny i przykładowe wyniki obliczeń numerycznych. Model matematyczny zbudowano w oparciu o jednowymiarowe równania mechaniki płynów. Do rozwiązania zagadnienia zastosowano metodę różnic skończonych. Analizowano zmiany ciśnienia i zmiany widma. Badano zbieżność i dokładność...
-
Molecular modeling of amphotericin B - ergosterol primary complex in water II
PublikacjaPrezentowane badania dotyczą oddziaływania antybiotyku polienowego anfoterycyny B (AmB) i ergosterolu (ERG) (typowego sterolu błonowego komórek grzybowych) na poziomie molekularnym. W odróżnieniu od badanego poprzednio kompleksu binarnego analizowany obecnie kompleks AnB/ERG/AmB charakteryzuje się zdecydowanie wiekszą stabilnością i wzglednie sztywną, sandwiczową geometrią. Za trwałość i geometrie kompleksu odpowiedzialne są oddziaływania...
-
Modeling the Customer’s Contextual Expectations Based on Latent Semantic Analysis Algorithms
PublikacjaNowadays, in the age of Internet, access to open data detects the huge possibilities for information retrieval. More and more often we hear about the concept of open data which is unrestricted access, in addition to reuse and analysis by external institutions, organizations and people. It’s such information that can be freely processed, add another data (so-called remix) and then published. More and more data are available in text...
-
Modeling of Heat Source Based on Parameters of Electron Beam Welding Process
Publikacja -
Modeling human thinking about similarities by neuromatrices in the perspective of fuzzy logic
Publikacja -
Preventing Work-Related Musculoskeletal Disorders in Manufacturing by Digital Human Modeling
Publikacja -
Processing and Maturation of Cathepsin C Zymogen: A Biochemical and Molecular Modeling Analysis
Publikacja