Filters
total: 1967
filtered: 1602
displaying 1000 best results Help
Search results for: INTEGRAL CROSS SECTION
-
Torsional buckling and post-buckling of columns made of aluminium alloy
PublicationThe paper concerns torsional buckling and the initial post-buckling of axially compressed thin-walled aluminium alloy columns with bisymmetrical cross-section. It is assumed that the column material behaviour is described by the Ramberg–Osgood constitutive equation in non-linear elastic range. The stationary total energy principle is used to derive the governing non-linear differential equation. An approximate solution of the equation...
-
Electronic states of tetrahydrofuran molecules studied by electron collisions
PublicationElectronic states of tetrahydrofuran molecules were studied in the excitation energy range 5.5-10 eV using the technique of electron energy loss spectroscopy in the gas phase. Excitation from the two conformations, C2 and Cs, of the ground state of the molecule are observed in the measured energy loss spectra. The vertical excitation energies of the 3(no3s) triplet state from the C2 and Cs conformations of the ground state of the...
-
Finite element modeling of plastic hinges based on ductility demand-capacity method using nonlinear material for dynamic analysis
PublicationThe article discusses modeling plastic hinges in reinforced concrete interme-diate supports using finite elements methods. The ductility demand-capacitymethod was used to determine the geometrical parameters of cross-section plas-ticization zones, their ability to move and rotate, as well as their ductility. Dueto the varied geometry and stiffness of the supports and their nonlinear behav-ior under dynamic load, this method was...
-
Dehydrogenation in electron-induced dissociative ionization of pyridine molecule
PublicationThe electron-impact dissociative ionization of pyridine has been investigated using mass spectrometry. Thirty-two well-resolved mass peaks have been identified in the cation mass spectra and assigned to the most likely ionic molecular fragments. The new sixteen ionic fragments' appearance energies have been determined, and sixteen others remeasured. The total cross-section for electron-impact ionization of pyridine has been measured...
-
Load-carrying capacity of axially loaded concrete-filled steel tubular columns made of thin tubes
PublicationAn experimental investigation was conducted on 30 CFST columns. An influence of the following factors on load-carrying capacity of the investigated columns was analyzed: the column slenderness (l1 = 42, l2 = 27 and l3 = 15), the tube thickness (the reinforcement ratio was equal to 4% or 6%), the way of applying the load to CFST columns (through the concrete core or through the entire cross-section), the bond strength between a...
-
The Effectiveness of Polymer Damper in Damage Reduction of Temporary Steel Grandstand
PublicationA large number of accidents involving damage of temporary grandstands during different types of events were observed in the past. The aim of the paper is to analyse numerically the effectiveness of a polymer damper in damage reduction of a temporary steel scaffolding grandstand exposed to dynamic load due to jumping. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Experimental and numerical study on polymer element used for reduction of temporary steel grandstand vibrations
PublicationThe purpose of the paper is to analyse the effectiveness of a polymer damper in reduction of a temporary steel grandstand vibrations through the experimental and numerical study. The damper considered in the investigation is constructed out of two L-shape steel members bonded with polymer mass of high damping properties. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Pedestrian safety in road traffic – studies, recommendations and proposed improvements
PublicationPedestrians are involved and most frequently the victims of every third road accident in Poland. Pedestrian accidents most frequently occur in complex circumstances, as a result of many factors related to the behaviour of drivers and pedestrians. The basic parameters that determine road safety include the perception of traffic and visibility on the road. The paper will present the results of research conducted within the project...
-
Structural and mechanical properties of hydroxyapatite coatings formed by ion-beam assisted deposition
PublicationThe ion-beam assisted deposition (IBAD) is an advanced method capable of producing crystalline coatings at low temperatures. We determined the characteristics of hydroxyapatite Ca10(PO4)6(OH)2 target and coatings formed by IBAD using X-ray photoemission spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and energy dispersive X-ray (EDX). The composition of the coatings'...
-
Assessing unsignalised pedestrian crossings
PublicationThe lack of pedestrian safety on crossings is a complex problem and one that is influenced by a number of factors such as the law, road traffic culture, the road and traffic. This paper will focus on the last two by presenting a method for assessing pedestrian crossings for their geometry and roadside using data from 930 pedestrian crossings in Warsaw. The authors of this paper have attempted to systematise the process of assessment...
-
Cultural Values Moderate the Impact of Relative Deprivation
Publication -
Psychometric Properties and Correlates of Precarious Manhood Beliefs in 62 Nations
Publication -
The Magnetic Fluid Seals Research Results vs. Kelvin-Helmholtz (K-H) instability and Preliminary Conclusions
PublicationIn the article a magnetic-fluid seals durability research and the tests results are presented. The tests were made with three magnetic fluids using various magnets quantity in magnetic assemblies. If values obtained in the repeated test deviated by more than 10 % from results of the first test an additional control test was made for final characteristics. The characteristics are: critical pressure, critical motion velocity and...
-
Selected Stability Problems of Thin-Walled Columns and Beams
PublicationThe article reviews a number of papers in the light of buckling analy- sis of thin-walled columns and beams. Stability of thin-walled columns and beams are considered a vital engineering science issue in both historical and present-day approaches. The paper refers to the recent authors’ works of the 2012–2019 period, published in leading journals. Similar review of stability problems of thin-walled structures developed at Gdansk...
-
On the existence of homoclinic type solutions of inhomogenous Lagrangian systems
PublicationWe study the existence of homoclinic type solutions for a class of inhomogenous Lagrangian systems with a potential satisfying the Ambrosetti-Rabinowitz superquadratic growth condition and a square integrable forcing term. A homoclinic type solution is obtained as a limit of periodic solutions of an approximative sequence of second order differential equations.
-
Design of modified PID controllers for 3D crane control
PublicationFrom the control viewpoint, 3D crane is a dynamic, nonlinear and multidimensional electromechanical system. In this paper, five control systems using a set-point weighted PID controllers (modified controllers) are designed. These structures and properties are presented. Optimization process of controllers settings based on integral performance indices is made. Simulation tests of control systems are presented. Comparison of integral...
-
Design of optimal state feedback controller with observer for multidimensional electrical system
PublicationFrom the control point of view, two-input-two-output RC electrical system is a linear and multidimensional system. In this paper, integral control and closed-loop observer are verified whether they can be used and designed. To verify this, Kalman tests are made. These structures are presented and discussed. Integral Control is tested with some base disturbances impact and checked whether it can handle them. The estimated values...
-
Fe-modified Mn2CuO4 spinel oxides: coatings based on abundant elements for solid oxide cell interconnects
PublicationThe current state of the art steel interconnect coating materials are based on critical raw material - Co-oxide spinels. Replacing Co-oxide spinels with alternative, abundant materials can reduce the dependence on the critical raw materials. Cobalt-free coatings with the general formula Mn2-xCuFexO4, where x = 0, 0.1, 0.3, were electrophoretically deposited on a ferritic stainless-steel support and evaluated. Prior to deposition,...
-
Multilayer coatings based on cerium oxide and manganese cobaltite spinel for Crofer22APU SOC interconnects
PublicationThe current state of the art steel interconnect coating materials are based on critical raw material - Co-oxide spinels. Replacing Co-oxide spinels with alternative, abundant materials can reduce the dependence on the critical raw materials. Cobalt-free coatings with the general formula Mn2-xCuFexO4, where x = 0, 0.1, 0.3, were electrophoretically deposited on a ferritic stainless-steel support and evaluated. Prior to deposition,...
-
Harmonization and Quality Assurance of Income and Wealth Data: The Case of LIS.
PublicationComparability of concepts in survey data harmonization is essential for scientific analyses. LIS – also known as the Luxembourg Income Study or LIS Cross-National Data Center in Luxembourg – acquires and harmonizes income and wealth microdata to provide the scientific community with a comparable database that is unique in the world in its growing temporal and geographic breadth. Over many decades, scholars worldwide have used the...
-
Political Sources of Government Redistribution in High-Income Countries
PublicationIn cross-national empirical work on income inequality and government redistribution, the greatest emphasis has been on the extremes of the income scale. Less work has been done on groups that are neither rich nor poor—the middle class. The lack of attention to this group is unfortunate for several reasons. Most obviously, the middle class, if defined as the three middle income quintile groups, is by far the largest income group,...
-
Non-proportional full-order Luenberger observers of induction motors
PublicationThe paper recapitulates recently conducted investigations of non-proportional Luenberger observers, applied to reconstruction of state variables of induction motors. Three structures of non-proportional observers are analyzed, a proportional-integral observer, modified integral observer and observer with integrators. Criteria for gain selection of the observer are described, classical ones based on poles, as well as additional,...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results. Part II Results of life tests of multi-stage magnetic - fluid seal operating in water
PublicationThe edge criteria for magnetic-fluid seals durability research were described in previous article [24] and now the tests results are presented. The tests were made with three magnetic fluids using various magnets quantity in magnetic assemblies. If values obtained in the repeated test deviated by more than 10 % from results of the first test an additional control test was made for final characteristics. The characteristics are:...
-
Structures for parameterization, meshing and data exchange of topologically related surfaces of a ship hull
PublicationThis paper presents proposal of data structures for storage and processing of a parametric three-dimensional model of a midship hull sections. The model consists of coarse surfaces like: decks, frames, girders, stiffeners, brackets, partitions etc. bounded by topological relations. All workshop details are omitted as the model is intended for numeric calculations. Proposed data structures are prepared to facilitate changes in the...
-
Estimation of the Maximum Permissible PV Power to be Connected to the MV Grid
PublicationIn recent decades, a significant increase in the share of renewable energy sources in power grids at various voltage levels has been observed. A number of articles have been published highlighting emerging problems in low-voltage grids with a large share of prosumers and in medium- and high-voltage grids to which photovoltaic (PV) plants are connected. The article analyzes the medium-voltage grid in terms of the possibility of...
-
Modelling of Longitudinal Elastic Wave Propagation in a Steel Rod Using the Discrete Element Method
PublicationThe paper deals with the issue of modelling elastic wave propagation using the discrete element method (DEM). The case of a longitudinal wave in a rod with a circular cross-section was considered. A novel, complex algorithm consisting of the preparation of models and simulation of elastic waves was developed. A series of DEM models were prepared for simulations, differing in discretisation and material parameters. Additional calculations...
-
Dynamic tests of composite footbridge segment – experimental and numerical studies
PublicationExperimental dynamic tests and numerical simulations of a 3 meters long segment of a footbridge made of polymer composites are presented in the paper. The span-length is reduced, however dimensions of cross-section are the same as the target footbridge. The segment structure is made of sandwich panels, which consist of fibre reinforced polymer (GFRP) laminates (skins) and a PET foam (core). The first part of the paper contains...
-
Influence of sheet/purlin fasteners spacing on shear flexibility of the diaphragm
PublicationThe paper presents the influence of sheet/purlin fasteners location (in reference to trapezoidal profile cross section) on shear flexibility of the cladding acting as a diaphragm. Analytical procedures were presented and their limitations were discussed. Next, selected schemes of fasteners location, known from engineering practice, but not included in European codes and recommendations, were analysed numerically in order to observe...
-
Digital technologies and women's empowerment – casting the bridges
PublicationThis work briefly discusses the nexuses between digital technology development and adoption across societies, and its potential impact on overall welfare through women’s economic empowerment. In the first section it sets out the context and background. Next, Section 2 demonstrates the state of access to and the use of digital technologies across the world. Section 3 intends to trace the causal links and channels of digital technologies'...
-
PI observer stability and application in an induction motor control system
PublicationThe paper discusses the problem of stability of a proportional-integral Luenberger observer, designated for the state variables reconstruction of a linear, time-invariant dynamical system.
-
Quantum corrections to phi^4 model solutions and applications to Heisenberg chain dynamics
PublicationThe Heisenberg spin chain is considered in φ^4 model approximation. Quantum corrections to classical solutions of the one-dimensional φ^4 model within the correspondent physics are evaluated with account of rest d−1 dimensions of a d-dimensional theory. A quantization of the model is considered in terms of spacetime functional integral. The generalized zeta-function formalism is used to renormalize and evaluate the functional integral...
-
Quantum corrections to 4 model solutions and applications to Heisenberg chain dynamics
PublicationThe Heisenberg spin chain is considered in φ^4 model approximation. Quantum corrections to classical solutions of the one-dimensional φ^4 model within the correspondent physics are valuated with account of rest d − 1 dimensions of a d-dimensional theory. A quantization of the model is considered in terms of space- time functional integral. The generalized zeta-function formalism is used to renormalize and evaluate the functional...
-
Electron scattering from 2-methyl–1,3-butadiene,C5H8, molecules: Role of methylation
PublicationWe report cross-section results from experimental and theoretical investigations into electron collisions with the 2-methyl–1,3-butadiene [C5H8] molecule. The current results are compared with our previous results for the 1,3-butadiene [C4H6] molecule, a structural homologue of 2-methyl–1,3-butadiene, to investigate how the methylation (the substitution of hydrogen atom by a methyl group) affects the shape and/or magnitude of the...
-
Flow maldistribution and its mitigation in mini heat exchangers
PublicationIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm x 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave mani-folds in Z-type flow configuration (16 different cases). The working medium was ethanol and the mass flow rate was 5×10-4 kg/s. Both sections was heated from the bottom side. Heat...
-
Numbers, Please: Power- and Voltage-Related Indices in Control of a Turbine-Generator Set
PublicationThis paper discusses the proper selection and interpretation of aggregated control performance indices values mirroring the quality of electrical energy generation by a turbine-generator set cooperating with a power system. Typically, a set of basic/classical and individual indices is used in energy engineering to ensure the mirroring feature and is related to voltage, frequency and active or reactive power deviations from their...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Resonances and Dissociative Electron Attachment in HNCO
PublicationIn a combined experimental and theoretical study, we probe the dissociative electron attachment in isocyanic acid HNCO. The experimental absolute cross section for the NCO− fragment shows a sharp onset and fine structures near the threshold. The autoionizing state responsible for the dissociative attachment is found in both the R-matrix calculation and using analytic continuation in the coupling constant. The involved A' resonance...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublicationIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...
-
Influence of nonlinearities on the efficiency and accuracy of FEM calculations on the example of a steel build-up thin-walled column
PublicationDue to the increase of computing capabilities of standard processing units, it is possible to perform complex analyses, considering a number of nonlinearities, such as geometric, material and boundary (contact) even on personal computers. In the paper, the authors have analysed the efficiency and accuracy of standard PC’s FEM calculations performed in Abaqus CAE 2017 software on the example of a critical load assessment of a thin-walled...
-
Multi-Stage Video Analysis Framework
PublicationThe chapter is organized as follows. Section 2 presents the general structure of the proposed framework and a method of data exchange between system elements. Section 3 is describing the low-level analysis modules for detection and tracking of moving objects. In Section 4 we present the object classification module. Sections 5 and 6 describe specialized modules for detection and recognition of faces and license plates, respectively....
-
The concept of aida applied to online interactive advertisement: an youtube case study
PublicationThis paper presents an approach of application of the AIDA framework to interactive advertisements presented on social media channels. The first section introduces the definitions of social media and its categorization. It is given an overview of the online video service YouTube.com. The second section describes social media marketing. The third section presents a theoretical introduction of traditional and interactive advertisement....
-
Optimum Control of Gyroscopic Systems
PublicationThe problem of optimum control of transverse rotor vibrations with gyroscopic interactions has been described and solved in the paper. An integral performance index has been defined for such system in order to minimize vibration level of a chosen rotor point. For this reason, an efficient way of finding the weight coefficients of integral performance index for multi-degrees-of-freedom system with gyroscopic interactions has been...
-
Thermohydraulic maldistribution reduction in mini heat exchangers
PublicationA detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm × 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave manifolds in Z-type flow configuration. The working medium was ethanol and the mass flow rate was 5 × 10−4 kg/s. Both sections were heated from the bottom side. Heat flux of 10 000 W/m2 and 5000 W/m2 was...
-
Charge Transfer, Complexes Formation and Furan Fragmentation Induced by Collisions with Low-Energy Helium Cations
PublicationThe present work focuses on unraveling the collisional processes leading to the fragmentation of the gas-phase furan molecules under the He+ and He2+ cations impact in the energy range 5–2000 eV. The presence of different mechanisms was identified by the analysis of the optical fragmentation spectra measured using the collision-induced emission spectroscopy (CIES) in conjunction with the ab initio calculations. The measurements of...
-
One Year Evaluation of Material Properties Changes of Polylactide Parts in Various Hydrolytic Degradation Conditions
PublicationBiodegradable biocompatible materials are widely used in medical applications. Determining the possibility of using biodegradable materials depends on determining the changes in their parameters over time due to degradation. The current scientific research on biodegradable materials has presented results based on research methods characterized by the different geometry and cross-section size of the specimen, type of degradation...
-
Separation of the effects of notch and macro residual stress on the MFL signal characteristics
PublicationMagnetic flux leakage (MFL) distribution for three configurations of samples has been investigated in order to study the influence of notch and plastic deformation separately as well as together. Samples have been made of S355 steel. The MFL signal measurements were carried out along the longest dimension of the sample over a length of 120 mm. Two components of magnetic field were measured: 1) tangential to the main axis and 2)...
-
Dissociative Electron Attachment to 5-Iodo-4-thio-2′-deoxyuridine: A Potential Radiosensitizer of Hypoxic Cells
PublicationIn the search for effective radiosensitizers for tumor cells, halogenated uracils have attracted more attention due to their large cross section for dissociation upon the attachment of low-energy electrons. In this study, we investigated dissociative electron attachment (DEA) to 5-iodo-4-thio-2'-deoxyuridine, a potential radiosensitizer using a crossed electron-molecule beam experiment coupled with quadrupole mass spectrometry....
-
Concrete-filled FRP tubular members in marine and bridge structures
PublicationConcrete core of the concrete-filled tubes (CFTs) with circular cross-section is in the case of an axial compression subjected to a spatial state of compressive stresses. This state leads to enhancement in the concrete strength. The enhancement is utilized in Eurocode 4 design procedures for CFSTs (i.e. CFTs with tube made of steel). The structural design of CFFTs (i.e. CFTs with tube made of Fibre Reinforced Polymer - FRP) is...
-
Experimental and numerical investigations of ultimate strength of imperfect stiffened plates of different slenderness
PublicationThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive...
-
Validation Process for Computational Model of Full-Scale Segment for Design of Composite Footbridge
PublicationExperimental tests and numerical simulations of a full-scale segment of a foot and cycle bridge made of polymer composites are presented in the paper. The analysed structure is made of sandwich panels, which consist of glass fibre reinforced polymer (GFRP) multi-layered laminate faces and a PET foam (obtained from recycling) core. The dimensions of the segment cross-section are the same as for the target footbridge; however, span...